TK-8102 CONTENTS / GENERAL CONTENTS GENERAL INTRODUCTION GENERAL ..............2 SCOPE OF THIS MANUAL OPERATING FEATURES ......... 4 This manual is intended for use by experienced techni- REALIGNMENT ............7 cians familiar with similar types of commercial grade com- munications equipment. It contains all required service in- DISASSEMBLY FOR REPAIR ........
TK-8102 OPERATING FEATURES 1-4. Display 1. Controls and Functions 1-1. Front Panel q w e Indicator Description Light while transmitting. Lights when a signal is detected 1-2. Microphone on the currently selected channel. Li g hts w hi l e t he f u n ct i o n p r o - grammed onto its corresponding key is activated.
OPERATING FEATURES • Scan ON/OFF 2. Operation Features Press this key starts scanning. Pressing this key stops The TK-8102 is a UHF FM radio designed to operate in scanning. conventional format. The programmable features are sum- • Talk around marized.
Page 6
TK-8102 OPERATING FEATURES Temporary delete Clear to transpond It is possible to delete channel temporary during scan. The transceiver waits the transpond of DTMF if channel When scan stops on unnecessary channel for example by is busy until channel open. This feature prevents the inter- interference of the other party, activate the delete function ference to other party.
For group calls, only the group tone will sound, not the transpond tone. 3-2. Connection Procedure 1. Connect the TK-8102 to the personal computer with the Pre alert tone interface cable. Sounds prior to the TOT TX inhibit activation. If TOT pre 2.
NOTE: Clone mode should enabled. 1. Turn the master TK-8102 power ON with the [1] key held down. The TK-8102 [ ] LED is turned on. 2. Power on the slave TK-8102.
TK-8102 DISASSEMBLY FOR REPAIR 3. To remove the display unit PCB, detach the PCB by 1. When you remove the panel, turn the transceiver up lifting at the indents of the PCB as shown below. side down. Detach the panel by lifting the tabs as shown below.
TK-8102 CIRCUIT DESCRIPTION IF Amplifier Frequency Configuration The first IF signal is amplified by Q19, and the enters IC5 The receiver utilizes double conversion. The first IF is (FM processing IC). The signal is heterodyned again with a 49.95MHz and the second IF is 450kHz. The first local oscil- second local oscillator signal within IC5 to create a 450kHz lator signal is supplied from the PLL circuit.
Page 11
TK-8102 CIRCUIT DESCRIPTION Wide/Narrow Changeover Circuit Squelch Circuit The Wide port (pin 92) and Narrow port (pin 91) of the The detection output from the FM IF IC (IC5) passes CPU is used to switch between ceramic filters. When the through a noise amplifier (Q18) to detect noise.
Page 12
TK-8102 CIRCUIT DESCRIPTION IC1 : PLL IC TX VCO RF AMP 5kHz/6.25kHz BUFF D10,12 Phase Charge comparator pump DATA RX VCO Q7,12 T/R SW 5kHz/6.25kHz D9,11 16.8MHz Fig. 6 PLL circuit Unlock Circuit Transmitter System During reception, the 8RC signal goes high, the 8TC sig- Outline nal goes low, and Q29 turns on.
Page 13
Key Matrix Circuit 2) Adjusts the AF signal level of the AF filter (IC10) and turns The TK-8102 front panel has function keys. Each of them the filter select compounder on or off. is connected to a cross point of a matrix of the KMI1 to 3) Controls the DTMF decoder (IC9).
Page 14
TK-8102 CIRCUIT DESCRIPTION Encode D/A Converter The QT and DQT signals are output from QT/DQT of the The D/A converter (IC3) is used to adjust MO modulation, CPU (IC6) and summed with the external pin DI line by the AF volume, TV voltage, FC reference voltage, and PC summing amplifier (IC4) and the resulting signal goes to the POWER CONTROL voltage level.
TK-8102 SEMICONDUCTOR DATA Microprocessor : 784214AGCXXX (TX-RX Unit IC6) Terminal function Pin No. Name Function Pin No. Name Function FNC8 Function Port8 DTMOSC DTMF IC Clock Control PLLE PLL IC Chip Select MUTE1 AF Mute EVLLD E-Volume LD MUTE2 Speaker Mute...
TK-8102 DESCRIPTION OF COMPONENTS Display Unit (X54-3340-20) Ref. No. Use/Function Operation/Condition DIODE ANT SW SYMBOL PARTS NAME DISCRIPTION DIODE APC VOLTAGE DETECT D1~4 KEY BACKLIT DIODE APC VOLTAGE DETECT MONITOR KEY LIGHT DIODE REVERSE CONNECT PROTECTION PROGRAMMABLE KEY LIGHT DIODE...
Page 17
TK-8102 DESCRIPTION OF COMPONENTS Ref. No. Use/Function Operation/Condition TRANSISTOR DC SWITCH(SB) /Active when power on TRANSISTOR AF MUTE /Active while Mute3 is H TRANSISTOR BEAT SHIFT /Active while Beat shift is on TRANSISTOR OVER VOLTAGE DETECTION /Active while PS voltage is more than 18V...
TK-8102 PARTS LIST ∗ New Parts. indicates safety critical components. Parts without Parts No. are not supplied. Les articles non mentionnes dans le Parts No. ne sont pas fournis. Teile ohne Parts No. werden nicht geliefert. TX-RX UNIT (X57-6300-20) TK-8102 Ref.
Page 19
TK-8102 PARTS LIST TX-RX UNIT (X57-6300-20) Ref. No. Address Parts No. Description Destination Ref. No. Address Parts No. Description Destination parts parts CK73GB1C104K CHIP C 0.10UF C176 CK73GB1H471K CHIP C 470PF CC73GCH1H270J CHIP C 27PF C177 CC73GCH1H070B CHIP C 7.0PF...
Page 20
TK-8102 PARTS LIST TX-RX UNIT (X57-6300-20) Ref. No. Address Parts No. Description Destination Ref. No. Address Parts No. Description Destination parts parts C268 C92-0568-05 CHIP-TAN 22UF 10WV C364,365 CK73GB1H471K CHIP C 470PF C366 CC73GCH1H070B CHIP C 7.0PF C269 CK73GB1H103K CHIP C 0.010UF K...
Page 21
TK-8102 PARTS LIST TX-RX UNIT (X57-6300-20) Ref. No. Address Parts No. Description Destination Ref. No. Address Parts No. Description Destination parts parts ∗ L41-1875-08 SMALL FIXED INDUCTOR RK73GB1J152J CHIP R 1.5K J 1/16W L34-4604-05 AIR-CORE COIL RK73GB1J683J CHIP R J 1/16W ∗...
Page 22
TK-8102 PARTS LIST TX-RX UNIT (X57-6300-20) Ref. No. Address Parts No. Description Destination Ref. No. Address Parts No. Description Destination parts parts R150 RK73GB1J102J CHIP R 1.0K J 1/16W R218 RK73GB1J394J CHIP R 390K J 1/16W R151 RK73GB1J103J CHIP R...
Page 23
TK-8102 PARTS LIST TX-RX UNIT (X57-6300-20) Ref. No. Address Parts No. Description Destination Ref. No. Address Parts No. Description Destination parts parts R295,296 R92-1252-05 CHIP R 0 OHM NJM2902V MOS IC R298 RK73GB1J101J CHIP R J 1/16W TK14489V BI-POLAR IC ∗...
TK-8102 EXPLODED VIEW N67-3008-46 PAN HEAD SEMS SCREW N87-2606-46 BRAZIER HEAD TAPTITE SCREW N87-2614-46 BRAZIER HEAD TAPTITE SCREW (For KEY 1 only) DISPLAY UNIT TX-RX UNIT Parts with the exploded numbers larger than 700 are not supplied.
TK-8102 PACKING 27 Bracket D SCREW SET (J29-0662-03) (N99-0395-05) 8 DC cord (E30-3339-05) Protection bag (H25-0103-04) 21 Inner Packing Case (H02-0617-02) 5 Instruction Manual (B62-1389-00) 22 Polystyrene Foamed Fixture 23 Polystyrene Foamed Fixture (H10-6636-03) (H10-6639-03) Protection Bag (H25-2320-04) 26 Item Carton Case (H52-1699-02) Parts with the exploded numbers larger than 700 are not supplied.
TK-8102 ADJUSTMENT Test Equipment Required for Alignment Test Equipment Major Specifications 1. Standard Signal Generator Frequency Range 400 to 520MHz (SSG) Modulation Frequency modulation and external modulation Output –127dBm/0.1µV to greater than –7dBm/100mV 2. Power Meter Input Impedance 50Ω Operation Frequency...
Page 27
TK-8102 ADJUSTMENT Note Adjustment Location • EEPROM Switch The tuning data (Deviation, Squelch, etc.) for the Volume EEPROM, is stored in memory. When parts are changed, up/down Display Power PF key readjust the transceiver. • AF PA IC (IC102) Speaker How to mounting the IC102.
Page 28
TK-8102 ADJUSTMENT Use KPG-70D programming software for adjustment of the next items. PCB Section Measurement Adjustment Specifications/ Item Condition Test equipment Terminal Parts Method Remarks 1. Setting 1) Power supply voltage DC Power supply teriminal:13.6V ±0.1V 2. VCO lock 1) CH: TX high Digital voltmeter 5.5V...
Page 29
TK-8102 ADJUSTMENT Transmitter section Measurement Adjustment Specifications/ Item Condition Test equipment Terminal Parts Method Remarks within ±100Hz 1. Frequency 1) CH: TX center Frequency PC key Adjust to center frequency 2) Transmit counter ±1.0W 2. High power 1) CH: TX low...
TK-8102 PC BOARD VIEW DISPLAY UNIT (X54-3340-20) Component side view + Foil side view DISPLAY UNIT (X57-3340-20) Component side view MONI POWER HOOK DOWN PROG POWER LEDMON LEDPF LEDC1 LEDC2 LEDR LEDG MICBL LEDC3 LEDC4 KMI1 KMI2 KMI3 KMI4 KMO1...
TK-8102 TERMINAL FUNCTION CN1 (TX-RX Unit) J1 (TX-RX Unit) Pin No. Name Function Pin No. Name Function Audio signal output to internal/external speaker. Ground Ground PTT/TXD HOOK Hook detection/RXD Mic ground J1 (Control Unit) Mic signal input Pin No. Name...