Advertisement
DCN Wireless 2.32 Release Notes
3 Release 2.31
3.1 General
3.1.1 Release
June 14th 2007.
3.1.2 Firmware/FPGA versions
Product
FPGA
DCN-WCCU
2.17
DCN-WDxx
1.01
DCN-WAP
1.01
DCN-DDB
--
DCN-DDI
2.0
DCN-FCS
2.5
DCN-IDESK
1.3
DCN-SWSMV
--
INT-TX04
2.2.0
INT-TX08
2.2.0
INT-TX16
2.2.0
INT-TX32
2.2.0
LBB 4402/00
--
LBB 4404/00
--
PRS-4DEX4
--
3.2 Compatibility restrictions
The following versions are not compatible with this
release:
3.2.1 DCN-IDESK
Product
FPGA
DCN-IDESK
1.1
3.2.2 DCN-SWSMV
DCN-SWSMV < 1.1 is not compatible with DCN
Wireless
3.2.3 DCN-MICS and DCN-MICL
Pluggable microphones < HW version 03.00 can
cause hum in DCN-Wireless system.
Pluggable Microphones with HW version ≥ 03.00
must be used, these can be recognized by marking
dot on connector, see picture below.
Bosch Communications Systems
SW
FW
2.31.1581
4.00.2075
--
--
2.31.0152
xx
1.4.XXXX
--
--
--
--
--
1.20.XXXX
--
1.20.0191
--
--
4.30.2160
--
4.30.2160
--
4.30.2160
--
4.30.2160
--
4.30.2160
--
4.30.2160
--
4.30.2160
SW
FW
--
--
3.3 Errata
3.3.1 Integrus manual: added menu 4B Network
mode
Menu 4B (Network mode) has been added.
Options:
• Automatic – use this when the transmitter is not
used in combination with DCN Next Generation
or DCN wireless.
• Enabled – use this when the transmitter is
exclusively used in combination with DCN Next
Generation or DCN wireless.
When the Integrus transmitter is alternately used in
combination with and without DCN Next Generation
or DCN wireless, then you can use the automatic
mode. In that case take care that the transmitter is
switched on after the other equipment in the DCN
Next Generation or DCN wireless system is
switched on, else unwanted behavior can occur.
In case 'enabled' is selected, while no DCN Next
Generation or DCN wireless system is connected,
the transmitter will show the fault status "Network
Error"
3.4 Known limitations Download &
License Tool
3.4.1 Downloading a DCN-WCCU and DCN-WAP
When downloading a DCN-WAP and/or DCN-
WCCU with an older version than 2.31: download
the DCN-WCCU and DCN-WAP without any other
optical device connected. Else the download may
fail.
3.4.2
Downloading DCN-WCCU fails when Windows
is not an English version
This is caused because the Download files can not
be found. The Download & License tool expects
that the Download files are in the following
directory: %SysteemRoot%\Program
Files\Bosch\Digital Congress Network\Download
and License Tool\Files\
drive where Windows is installed)
In a non English Windows the folder "Program
Files" is called differently, therefore the files are not
found. The temporary workaround is:
•
Log in as administrator
•
Go to the directory where the Download
Tool is installed " \Program
Files\Bosch\Digital Congress
Network\Download and License Tool ".
"Program Files" will be in local language.
•
Open the with Notepad.exe the file:
DownloadTool.exe.config
•
Go to section <filelocation>
•
Within that section " \Program
Files\Bosch\Digital Congress
en | 8
(%SystemRoot% is the
Advertisement
