Page 2
Alternatively, wear a dis- tion, replace the picture tube only with one that charging Wrist-strap device. (Be sure to is the same type as the original. remove it prior to applying power--this is an electric shock precaution.) Samsung Electronics...
Page 3
17. Observe the original lead dress, especially near the following areas : Antenna wiring, sharp edges, and especially the AC and high voltage power supplies. Always inspect for pinched, out-of-place, or frayed wiring. Do not change the spacing between components and the Samsung Electronics...
3. Disassembly and Reassembly 3-1. Cabinet and PCB 3-1-1 Ass’y Case Top Removal 1 Screw 2EA Removal 2 Bracket Accessory Shoe Removal 3 Screw 1EA Removal 4 Ass’y-Case Top Removal Fig. 3-1 Ass’y Case Top Removal Samsung Electronics...
Page 7
Disassembly and Reassembly 3-1-2 Ass’y-Case Front Removal 2 Ass’y Case Front Removal 1 Screw 1EA Removal Fig.3-2 Ass’y Case Front Removal Samsung Electronics...
5. After setting adjustment value, please press “START/STOP” button on the remote controller to confirm DATA. –:– –:– –:– – VCR ADJ Indicates current adjustment item. EPR:FF EVR:FF Indicates the adjusted values Indicates preset values Samsung Electronics...
Page 15
Tape Eject Fig.2. REMOCON KEY STEP 3 . If you want to finish the adjustment mode, you have to do Power Reset. The Power Reset means that you pull out the power source and pull in it again. Samsung Electronics...
Page 16
Y LEVEL LUMI LEVEL (FIX) C LEVEL COLOR LEVEL(FIX) AGC-MARK ACC-MARK S-AGC-MARK-OFFSET S-ACC-MARK-OFFSET LCD COLOR OFFSET DIF INITIAL MODELINITIAL Value MODEL Adj. Value SCD180 MODEL DATA – VP-D190MSi VP-D190MS D.ZOOM MODEL Adj. Value D.ZOOM – All model HEAD SW ADJUST –...
1) Use the buttons on the remote control when adjusting camera. 2) Press the "START/STOP" button when storing confirmed adjustment value of each adjustment step in EEPROM. 3) The OSD shows “OK” after finishing each adjustment step. 4) To clear the adjustment mode, pull out the power source. Samsung Electronics...
Page 18
STEP 3 4) The OSD appears. CAMERA ADJ O C D Monitor OSD shows " ". EPR : F F EVR : F F Then camera adjustment mode has been activated successfully. Note : "XX" indicates variable values. Samsung Electronics...
M OTO R _ D R I V E T I M E 0 2 4 M OTO R _ C H O P P I N G 0 2 5 M OTO R _ E X T P I N 0 2 6 M OTOR_EVRA/_FOCUS MOTOR CURRENT Samsung Electronics...
Page 20
A F _ O P T I O N 3 0 5 4 Dual zoom speed[00,01,02,03=MAX] 0 5 5 A F _ O P T I O N 4 0 5 6 A F _ O P T I O N 5 Samsung Electronics...
Page 21
WB_RIGHT AREA _DIVIDE SCALE 0 8 4 WB_LEFT AREA _DIVIDE SCALE 0 8 5 W B - W H I T E _ D E T E C T I O N _ ROUTINE SELECT OPTION 0 8 6 @ R_GAIN_POSI_5100 Samsung Electronics...
Page 22
0 B 3 N O _ U S E D 0 B 4 Ae Control Value At Adjt 0 B 5 Agc Min Limit Va l u e 0 B 6 Agc Max Limit Va l u e Samsung Electronics...
Page 23
(#0B5~ #1DA ~#0E3) 0 E 4 agc middle chroma suppress. Percent of #142 0 E 5 agc middle noise slice (#133) 0 E 6 agc middle Y H - A P T-GAIN+ (max:1F)(#131) Samsung Electronics 4-10...
Page 24
V _ Z M _ S U B _ O d d [ 7 : 0 ] 1 1 5 V _ Z M _ S K I P [ 7 : 0 ] 1 1 6 Y C _ D LY [ 7 : 0 ] Samsung Electronics 4-11...
Page 25
PA S T E L _ O F F S E T [ 7 : 0 ] 1 4 6 E M B O S S I N G _ O F F S E T [ 7 : 0 ] 4-12 Samsung Electronics...
Page 26
C _ B Y _ G P [ 7 : 0 ] 1 7 5 C _ B Y _ G N [ 7 : 0 ] 1 7 6 C _ B Y _ H P [ 7 : 0 ] Samsung Electronics 4-13...
Page 27
A E _ T H R _ H i G H [ 7 : 0 ] 1 A 5 A E _ T H R _ L OW [ 7 : 0 ] 1 A 6 AW B _ T H R _ H i G H [ 7 : 0 ] 4-14 Samsung Electronics...
Page 28
1 D 6 D S P _ D S E _ YA P T _ N S L I C E A F T E _ G A M _ E M B O _ # 1 5 8 Samsung Electronics 4-15...
Page 29
C O L O R _ B A R _ PATTERN_GEN FOR LCD(CVF)_ADJUST_#168 1 F E C O L O R _ B A R _ PATTERN_GEN FOR LCD(CVF)_ADJUST_#169 1 F F R E V I S I O N _ DAT E 4-16 Samsung Electronics...
Page 30
3) Press the FF(Mode UP)/REW(mode Down) button so that OSD shows “OD6 XX XX”. 4) Press the START/STOP (Confirm) button. 5) Then Micom finds out Zoom VR center position. Store Zoom VR center value in OB7. 3m +/-1Cm Samsung Electronics 4-17...
Page 31
OAC respectively. closed. Store max. and min. value of in OBC, 6) The OSD shows “OK” after finishing the adjust- OBD and OBA, OBB respectively. ment. 6) The OSD shows “OK” after finishing the adjustment. 95±5IRE 95±5IRE 4-18 Samsung Electronics...
Page 32
1) Camera mode & 3100˚ K color bar chart adjustment. 2) Connect a video output terminal to a vec- torscope and a TV. 3) Press the FF(Mode Up)/REW(Mode Down) button so that OSD shows "170 XX XX". 55IRE Samsung Electronics 4-19...
Page 33
40IRE. store data. 6) Press the START/STOP (Confirm) button to 7) The OSD shows “OK” after finishing the store data. adjustment. 7) The OSD shows “OK” after finishing the adjustment. 60IRE 40IRE 4-20 Samsung Electronics...
Page 34
1500-2000 Lux. 5) Press the PLAY (Data Up)/STOP (Data Down) so that the blue level is 30IRE. 6) Press the START/STOP (Confirm) button to store data. 7) The OSD shows “OK” after finishing the adjustment. Samsung Electronics 4-21...
Page 35
1500-2000 Lux. 5) Press the PLAY (Data Up)/STOP (Data Down) so that the red vectors is 108˚ . 6) Press the START/STOP (Confirm) button to store data. 7) The OSD shows “OK” after finishing the adjustment. 4-22 Samsung Electronics...
Page 36
1500-2000 Lux. 5) Press the PLAY (Data Up)/STOP (Data Down) BLUE VECTOR 345 DEG so that the cyan vector is 280˚ . 6) Press the START/STOP (Confirm) button to store data. Samsung Electronics 4-23...
Page 37
4) Ensure that camera picks up image on 3100˚ K color bar chart precisely and the illumination is 1500-2000 Lux. 5) Press the PLAY (Data Up)/STOP (Data Down) so that the yellow vector is 168˚ . 6) Press the START/STOP (Confirm) button to store data. 4-24 Samsung Electronics...
Page 38
Shift adjustment address to left. Shift adjustment address to right. REW (Mode Down) Up value. PLAY (Data Up) Down value. STOP (Data Down) Note: In service adjustment mode, button names are different from those in customer function control mode. Samsung Electronics 4-25...
Page 39
4. How to adjust A d d r e s s N a m e USR BRT S, BRT R S, BRT B TRANS LCD CONN. (R, G, B wave fo rm on each T P ) 4-26 4-26 Samsung Electronics...
Page 40
TP-R on the white level of TP- G (There are usage of adjustment in Function of each button on the remote con- trol) f) Make sure that “OK” is displayed on LCD screen Samsung Electronics 4-27 4-27...
Page 41
Alignment and Adjustment 5) Adjustment of TP-B How to adjust (TP-B) is on same process of TP-R Don’t forget! to you must compare TP-G with TP- B too 4-28 Samsung Electronics...
Page 42
Shift adjustment address to right. REW (Mode Down) Up value. PLAY (Data Up) Down value. STOP (Data Down) Note: In service adjustment mode, button names are different from those in customer function control mode. Samsung Electronics Samsung Electronics 4-29 4-29...
Page 43
4. How to adjust A d d r e s s N a m e LCD CONN. USR BRT S, BRT R S, BRT B (R, G, B wave fo rm on each T P ) 4-30 4-30 Samsung Electronics Samsung Electronics...
Page 44
If not some position you must adjust the white level of TP-R on the white level of TP- G (There are usage of adjustment in Function of each button on the remote con- trol) f) Make sure that “OK” is displayed on LCD screen Samsung Electronics 4-31...
Page 45
(waveform of G and B) Adjust so that white level of G and B signal is s a m e. (waveform of G and R) Adjust so that white level of G and R signal is s a m e. 4-32 Samsung Electronics...
Page 46
4-5-2. EVF adjustment 1) VIDEO GAIN a) Connect an oscilloscope probe to TP-V. b) Adjust the VRE02 so that A level is 2.5 Vp-p Remote Control Button Location 10 PIN CON. 2 PIN CON. Location of Test Point Samsung Electronics 4-33...
Page 47
Alignment and Adjustment 4-34 Samsung Electronics...
Page 51
Exploded View and Parts List 5-2 Ass’y EVF (SCD180) Samsung Electronics...
Page 52
Exploded View and Parts List Loc. No New Part No Description and Specification Remark AD97-03635A ASSY-EVF;EVF(NTSC) SCD180 AD63-00268A COVER-LCD/LIGHT EVF;ABS 94-HB BLK AD61-00768A HOLDER-LCD/LIGHT EVF;PC+G/F 20% BLK AD61-00769A HOLDER-LENS EVF;ABS 94-HB BLACK AD64-00636A KNOB-EVF;POM BLACK AD67-00142A LENS-EVF UP G3;PMMA AD97-04174A ASSY BL;EVF(0.24"") AD07-00009A LCD-PANNEL;EVF(0.24"")
Page 53
Exploded View and Parts List Exploded View and Parts List 5-3 Ass’y CVF (VP-D190MS/D190MSi) Samsung Electronics Samsung Electronics...
Page 114
«•¡ˆ øµπÆ 2001.7.4 2:0 PM ∆‰¿Ã¡ˆ1 DIGITAL COMCORDER DECK CSM-2000 ¢¬ File with the SERVICE MANUAL. DIGITAL CAMCORDER DECKCONTENTS 1. Operation 2. Adjustment 3. Disassembly and Re...
Page 115
«•¡ˆ øµπÆ 2001.7.4 2:0 PM ∆‰¿Ã¡ˆ2 E L E C T R O N I C S...
Page 121
LD 1 °È Brakes S ¶Ë released or operated to Reel Disk S ¶È by slide Main ¶Á. LD 2 STOP MOTOR LOADING £U SLIDE MAIN ¶Á REEL DISK S ¶È BRAKE S ¶Ë CHASSIS SUB ¶Ê Fig 1-6 Samsung Electronics...
Page 123
1. µø¿¤ øµπ Æ 2001.7.4 2:3 PM ∆‰¿Ã¡ˆ1-8 EJECT UNLOAD LD 1 LD 2 STOP PLAY MOTOR LOADING ¶Â SPRING TENSION ¶È GEAR MODE SWITCH ¶Ï CHASSIS SUB ¶Ê...
Page 124
1. µø¿¤ øµπ Æ 2001.7.4 2:3 PM ∆‰¿Ã¡ˆ1-9 EJECT UNLOAD LD 1 LD 2 STOP PLAY PINCH ROLLER ¶Í ARM PINCH ¶Ë SPRING LEVER PINCH ¶Ï SLIDE MAIN ¶È CAM CURVE A ¶Á CHASSIS SUB ¶Ê...
Page 125
1. µø¿¤ øµπ Æ 2001.7.4 2:3 PM ∆‰¿Ã¡ˆ1-10 EJECT UNLOAD LD 1 LD 2 STOP PLAY CHASSIS MAIN ¶Á CAM CURVE ¶Ë CHASSIS SUB ¶Ê...
Page 126
1. µø¿¤ øµπ Æ 2001.7.4 2:3 PM ∆‰¿Ã¡ˆ1-11 EJECT UNLOAD LD 1 LD 2 STOP PLAY BASE DRUM ¶Ô GEAR WHEEL ¶Ê GEAR MODE SWITCH ¶Á GEAR LOADING T ¶Î POLE BASE S ¶Ï POLE BASE T ¶Ï GEAR CONNECTOR ¶È GEAR CAM MAIN ¶Ë...