1. Manuals
  2. Brands
  3. Toshiba Manuals
  4. Laptop
  5. Satellite M100 Series
  6. Maintenance manual

Toshiba Satellite M100 Maintenance Manual

Hide thumbs Also See for Satellite M100:
Table of Contents

Advertisement

Quick Links

See also: User Manual
Toshiba Personal Computer
Satellite M100
Maintenance Manual
TOSHIBA CORPORATION
[CONFIDENTIAL]

Advertisement

Table of Contents
loading

Related Manuals for Toshiba Satellite M100

Summary of Contents for Toshiba Satellite M100

  • Page 1 Toshiba Personal Computer Satellite M100 Maintenance Manual TOSHIBA CORPORATION [CONFIDENTIAL]...
  • Page 2 © 2006 by Toshiba Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of Toshiba. No patent liability is assumed with respect to the use of the information contained herein.

  • Page 3: General

    This maintenance manual describes how to perform hardware service maintenance for the Toshiba Personal Computer Satellite M100, referred to as the M100 Series in this manual. The procedures described in this manual are intended to help service technicians isolate faulty Field Replaceable Units (FRUs) and replace them in the field.
  • Page 4 Chapter 4 Replacement Procedures describes the removal and replacement of the FRUs. Appendices The appendices describe the following: Handling the LCD module Board layout Pin assignments Keyboard scan/character codes Key layout Screw torque list Reliability [CONFIDENTIAL] Satellite M100 Series Maintenance Manual...
  • Page 5 Text that you are instructed to type in is shown in the boldface type below: DISKCOPY A: B: The display Text generated by the computer that appears on its display is presented in the typeface below: Format complete System transferred [CONFIDENTIAL] Satellite M100 Series Maintenance Manual...
  • Page 6 [CONFIDENTIAL] Satellite M100 Series Maintenance Manual...

  • Page 7: Table Of Contents

    Printer Port Troubleshooting..................2-21 TouchPad Troubleshooting.................... 2-23 2.10 Speaker Troubleshooting ....................2-27 2.11 Optical Drive Troubleshooting ..................2-29 2.11 Modem Troubleshooting....................2-32 2.12 PCMCIA Troubleshooting..................... 2-34 2.13 IEEE 1394 Troubleshooting ..................2-36 2.14 Wireless LAN Troubleshooting..................2-38 [CONFIDENTIAL] Satellite M100 Series Maintenance Manual...
  • Page 8 3.12 Mouse (Pad) Test ......................3-16 3.13 LCD Pixels Mode Test....................3-18 3.14 Lid Switch Test ......................3-19 3.15 HDD R/W Test ......................3-20 3.16 LAN Test ........................3-22 3.17 RTC Test........................3-24 [CONFIDENTIAL] Satellite M100 Series Maintenance Manual viii...
  • Page 9 Fan & CPU........................4-45 4.19 USB Module ........................4-48 4.20 VGA Module ......................... 4-49 4.21 Display Mask ......................... 4-50 4.22 Speakers ......................... 4-52 4.23 FL Inverter Board ......................4-53 4.24 LCD Module ........................4-54 [CONFIDENTIAL] Satellite M100 Series Maintenance Manual...
  • Page 10 Handling the LCD Module ................. A-1 Appendix B Board Layout ...................... B-1 Appendix C Pin Assignments....................C-1 Appendix D Keyboard Scan/Character Codes ................ D-1 Appendix E Key Layout......................E-1 Appendix F Series Screw Torque List ..................F-1 Appendix G Reliability......................G-1 [CONFIDENTIAL] Satellite M100 Series Maintenance Manual...

  • Page 11: Chapter 1 Hardware Overview

    Chapter 1 Hardware Overview [CONFIDENTIAL]...
  • Page 12 1 Hardware Overview [CONFIDENTIAL] 1-ii Satellite M100 Maintenance Manual...
  • Page 13 Optical device Drives....................1-10 1.4.1 DVD-ROM & CD-RW ................1-10 1.4.2 DVD-ROM....................1-11 1.4.3 DVD Super Multi Double Layer............... 1-12 Power Supply ......................1-13 Batteries ........................1-15 1.6.1 Main Battery....................1-16 1.6.2 RTC battery ....................1-17 [CONFIDENTIAL] Satellite M100 Series Maintenance Manual 1-iii...
  • Page 14 2.5-inch HDD ....................1-9 Tables Table 1-1 2.5-inch HDD specifications ................. 1-9 Table 1-2 DVD-ROM & CD-RW drive specifications ..........1-10 Table 1-3 DVD-ROM drive specifications..............1-11 Table 1-4 DVD Super Multi Double Layer drive specifications......... 1-12 [CONFIDENTIAL] 1-iv Satellite M100 Maintenance Manual...

  • Page 15: Features

    1.1 Features 1 Hardware Overview Features The Satellite M100 Series Personal Computer uses extensive Large Scale Integration (LSI), and Complementary Metal-Oxide Semiconductor (CMOS) technology extensively to provide compact size, minimum weight and high reliability. This computer incorporates the following features and benefits: •...
  • Page 16 • 6 cells of Li-Ion 18650 size, smart battery pack with 4000mAH x 10.8V (43.2W) • 9 cells of Li-Ion 18650 size, smart battery pack with 6000mAH x 10.8V (64.8W) • 12 cells of Li-Ion 18650 size smart battery pack with 8600mAH x 10.8V (92.88W) [CONFIDENTIAL] Satellite M100 Maintenance Manual...
  • Page 17 • PCIe mini card wireless module (802.11a+b+g Askey WLAN module, 802.11a+b+g Intel WLAN module) • Dual-band built-in antenna for wireless LAN communication • MDC Modem • External PCMCIA form factor remote control devices • Internal USB interface Bluetooth module V2.0 with EDR [CONFIDENTIAL] Satellite M100 Series Maintenance Manual...
  • Page 18 • One type II card socket with shutter door • TI 7412 controller • PC card 95 supported • No ZV-port support • SRAM, OTPROM, FLASH ROM, mask ROM memory card up to 64MB • Modem/LAN card [CONFIDENTIAL] Satellite M100 Maintenance Manual...
  • Page 19 • The computer comes with an RJ-45 Local Area Network (LAN) port. The computer has built-in support for Ethernet LAN (10 megabits per second, 10BASE-T), Fast Ethernet LAN (100 Mbps 100BASE-TX), or Gigabit Ethernet LAN (1000 Mbps, 1000BASE-T). [CONFIDENTIAL] Satellite M100 Series Maintenance Manual...

  • Page 20: Features

    • HDD local standby mode by time out • LCD local standby mode by time out • Low battery alarm by beep • Auto-backlight off when LCD cover closed • Full ACPI 1.0B supported • LCD auto-dim mode by time out [CONFIDENTIAL] Satellite M100 Maintenance Manual...

  • Page 21: System Unit

    • Slot: 2 SO-DIMM up to 1GB can be upgraded through memory expansion slot. You need to remove existing SO-DIMM if SO-DIMM is installed in memory expansion slot. Maximum upgradeable system memory depends on the model. [CONFIDENTIAL] Satellite M100 Series Maintenance Manual...
  • Page 22 − Internal Microphone array − Two stereo speakers − Sound effect by SRS software − Driver level support for all applications by Toshiba virtual sound − Volume control: Dial type for Win XP − Stereo speakers with box or Harman/kardon(Odessey2)

  • Page 23: Inch Hard Disk Drive

    195,371,568 234,441,648 (LBA) Rotational 5400 5400/7200 5400/7200 5400/7200 5400 speed (rpm) Toshiba HDD 16/NA 16/NA 16/NA Buffer (MB) Hitachi HDD Buffer (MB) Fujitsu HDD Buffer (MB) Bytes per sector Table 1-1 2.5-inch HDD specifications [CONFIDENTIAL] Satellite M100 Series Maintenance Manual...

  • Page 24: Optical Device Drives

    16.6 (PIO mode 4, Multiword DMA mode 2) Access time (ms) Average random access Data buffer size (Mbytes) DVD: DVD-VIDEO, DVD-ROM Formats supported CD-DA, CD-ROM, CD-R, CD-RW, CD-ROMXA, PhotoCD (single/multi-session), CD-EXTRA, CD-Text Table 1-2 DVD-ROM & CD-RW drive specifications [CONFIDENTIAL] 1-10 Satellite M100 Maintenance Manual...

  • Page 25: Dvd-Rom

    16.6 (PIO mode 4, Multiword DMA mode 2) Access time (ms) Average random access Data buffer size (Mbytes) 256 KB DVD: DVD-VIDEO, DVD-ROM Formats supported CD-DA, CD-ROM, CD-R, CD-RW, CD-ROMXA, PhotoCD (single/multi-session), CD-EXTRA, CD-Text Table 1-3 DVD-ROM drive specifications [CONFIDENTIAL] Satellite M100 Series Maintenance Manual 1-11...

  • Page 26: Dvd Super Multi Double Layer

    Data buffer size (Mbytes) DVD: DVD-VIDEO, DVD-ROM, DVD-R, DVD-RW, DVD-RAM, DVD+R, DVD+RW, DVD+R DL, DVD-R DL Formats supported CD-DA, CD-ROM, CD-R, CD-RW, CD-ROMXA, PhotoCD (single/multi-session), CD-EXTRA, CD-Text Table 1-4 DVD Super Multi Double Layer drive specifications [CONFIDENTIAL] 1-12 Satellite M100 Maintenance Manual...

  • Page 27: Power Supply

    1 Hardware Overview Power Supply This specification defines the performance and characteristics of the 75W AC adapter power supply. It supplies a constant voltage 15V output source for Satellite M100 series notebook computer. A/D conversion • The EC uses 10-bit sampling for A/D conversion to determine the following values: –...
  • Page 28 • When a new battery is installed, the EC communicates with the E PROM in the battery to read information of the newly installed battery. Battery capacity calculation • The EC reads battery remaining and percentage capacity from the battery through SMBus. [CONFIDENTIAL] 1-14 Satellite M100 Maintenance Manual...

  • Page 29: Batteries

    Output voltage Capacity Main battery (6 cell) Lithium-Ion 10.8V 4000 mAh Main battery (9 cell) Lithium-Ion 10.8V 6000 mAh Main battery (12 cell) Lithium-Ion 10.8V 8600 mAh RTC battery Lithium 3.0V 15 mAh [CONFIDENTIAL] Satellite M100 Series Maintenance Manual 1-15...

  • Page 30: Main Battery

    4. The battery temperature is abnormal. 5. The battery SMBus communication fails. 6. The battery cell is bad. Detection of full charge A full charge is detected from the battery pack through SMBus when the battery is charging. [CONFIDENTIAL] 1-16 Satellite M100 Maintenance Manual...

  • Page 31: Rtc Battery

    RTC battery. The RTC battery is charged by the adaptor or main battery, while the computer is powered on. Status Time Charging Time (power on) About 24 hours Data preservation period (full charge) 1 month [CONFIDENTIAL] Satellite M100 Series Maintenance Manual 1-17...

  • Page 32: Troubleshooting Procedures

    Chapter 2 Troubleshooting Procedures...
  • Page 33 PCMCIA Troubleshooting..................2-32 2.13 IEEE 1394 Troubleshooting ..................2-34 2.14 Wireless LAN Troubleshooting................2-36 2.15 5IN1 card troubleshooting ..................2-38 2.16 Bluetooth Troubleshooting………………………………………………….………2-40 2.17 Fingerprint Troubleshooting………………………………………………………...2-42 2.18 3D G sensor (3D HDD Protection) Troubleshooting………………………………..2-44 [CONFIDENTIAL] Satellite M100 Series Maintenance Manual 2-ii...

  • Page 34: Troubleshooting Flowchart

    Bluetooth troubleshooting process ………………………………….……2-40 Figure 2-16 Fingerprint troubleshooting process………………………………………..2-42 Figure 2-17 TPM Troubleshooting process……………………………………………...2-44 Figure 2-18 3D HDD Protection Troubleshooting process………………………………2-46 Tables Table 2-1 Battery LED ...................... 2-8 Table 2-2 DC-IN LED....................... 2-9 [CONFIDENTIAL] Satellite M100 Series Maintenance Manual 2-iii...

  • Page 35: Troubleshooting Introduction

    9. External monitor 10. USB compatible keyboard 11. Multimedia sound system with line-in and line-out ports 12. Headphones 13. USB test module and USB cable 14. Music CD 15. 6IN1 Card (SD/MMC/MS/MS Pro/XD/mini SD) [CONFIDENTIAL] Satellite M100 Series Maintenance Manual...

  • Page 36: Troubleshooting Flowchart

    Ask the user if a password is registered and, if it is, ask him or her to enter the password. Verify with the customer that Toshiba Windows XP is installed on the hard disk. Operating systems that were not preinstalled by Toshiba can cause the computer to malfunction.
  • Page 37 R u n C M 1 6 5 .E X E a n d se le c t th e H A R D D IS K ite m . Y es Figure 2-1 Troubleshooting flowchart (1/2) [CONFIDENTIAL] Satellite M100 Series Maintenance Manual...
  • Page 38 After confirming which diagnostics test has detected Is an error detected by any of the an error, perform the diagnostics tests? appropriate procedure as outlined below. System is normal Figure 2-2 Troubleshooting flowchart (2/2) [CONFIDENTIAL] Satellite M100 Series Maintenance Manual...
  • Page 39 5. If an error is detected by the audio test, perform the Speaker Troubleshooting procedures in Section 2.9 and the Optical Drive Troubleshooting Procedures in Section 2.9. 6. If an error is detected by the modem test, perform the Modem Troubleshooting Procedures in Section 2.10. [CONFIDENTIAL] Satellite M100 Series Maintenance Manual...
  • Page 40 6. If an error is detected when using the IEEE1394 device, perform the IEEE1394 device Troubleshooting procedures in Section 2.14. 7. If an error is detected when using the Wireless LAN, perform the Wireless LAN Troubleshooting procedures in Section 2.15. [CONFIDENTIAL] Satellite M100 Series Maintenance Manual...

  • Page 41: Power Supply Troubleshooting

    (P rocedure 4) P erform internal connection A re the internal power check connections secure? (P rocedure 5) Y es R eplace system board E N D Figure 2-3 Power Supply Troubleshooting Process [CONFIDENTIAL] Satellite M100 Series Maintenance Manual...
  • Page 42 (LED on for 1 second protected and cannot be re-powered on every 2 seconds) without the AC power connected. Amber color off Battery not in low or critical low state; It’s in discharging state [CONFIDENTIAL] Satellite M100 Series Maintenance Manual...
  • Page 43 Check 1 Connect a new AC adaptor. If the problem is not resolved, go to Check 2. Check 2 Insert a new battery. If the problem is still not resolved, go to Procedure 3. [CONFIDENTIAL] Satellite M100 Series Maintenance Manual...
  • Page 44 • If the battery LED does not light, go to Check 6. Check 6 Make sure the battery pack is installed in the computer correctly. If the battery is properly installed and the battery LED still does not light, go to Procedure 4. [CONFIDENTIAL] Satellite M100 Series Maintenance Manual 2-10...
  • Page 45 Make sure that the battery cable is firmly connected to the system board. If it is connected firmly, go to Check 3. Check 3 The system board may be damaged. Replace it with a new one following the instructions in Chapter 4. [CONFIDENTIAL] Satellite M100 Series Maintenance Manual 2-11...

  • Page 46: Display Troubleshooting

    ( P r o c e d u r e 3 ) R e p la c e s y s te m b o a r d E N D Figure 2-4 Display troubleshooting process [CONFIDENTIAL] Satellite M100 Series Maintenance Manual 2-12...
  • Page 47 Refer to Chapter 3, Tests and Diagnostics for details. If an error is detected, go to Procedure 3. If an error is not detected, the display is functioning properly. [CONFIDENTIAL] Satellite M100 Series Maintenance Manual 2-13...
  • Page 48 Check 5 Replace the CPU with another of the same specifications. If the problem still exists, perform Check 6. Check 6 The system board may be damaged. Replace it with a new one. [CONFIDENTIAL] Satellite M100 Series Maintenance Manual 2-14...

  • Page 49: Keyboard Troubleshooting

    ( P r o c e d u r e 3 ) R e p la c e s y s te m b o a r d E N D Figure 2-5 Keyboard troubleshooting process [CONFIDENTIAL] Satellite M100 Series Maintenance Manual 2-15...
  • Page 50 The keyboard may be damaged. Replace it with a new one following the instructions in Chapter 4. If the problem still exists, perform Check 3. Check 3 The system board may be damaged. Replace it with a new one following the instructions in Chapter 4. [CONFIDENTIAL] Satellite M100 Series Maintenance Manual 2-16...

  • Page 51: External Usb Devices Troubleshooting

    R e p la c e s y s te m b o a r d ( P r o c e d u r e 2 ) E N D Figure 2-6 External USB device troubleshooting process [CONFIDENTIAL] Satellite M100 Series Maintenance Manual 2-17...
  • Page 52 Go to Procedure 2. Procedure 2 Replace system board If the error persists, the system board may be damaged. Replace it with a new one following the instructions in Chapter 4. [CONFIDENTIAL] Satellite M100 Series Maintenance Manual 2-18...

  • Page 53: Tv-Out Failure Troubleshooting

    T V fu n c tio n in g o k ? s e t Y e s R e p la c e s y s te m b o a r d E N D Figure 2-7 TV-out troubleshooting process [CONFIDENTIAL] Satellite M100 Series Maintenance Manual 2-19...
  • Page 54 Try connecting a different television to the computer. If the replacement television works, the original set may be damaged. If the replacement set does not work the system board may be damaged. Replace it with a new one following the instructions in Chapter 4. [CONFIDENTIAL] Satellite M100 Series Maintenance Manual 2-20...

  • Page 55: Touchpad Troubleshooting

    2.8 Touch Pad Troubleshooting 2 Troubleshooting Procedures TouchPad Troubleshooting START TouchPad connection check (Procedure 1) TouchPad replacement check (Procedure 2) Replace system board Figure 2-8 TouchPad troubleshooting process [CONFIDENTIAL] Satellite M100 Series Maintenance Manual 2-21...
  • Page 56 The TouchPad unit or FPC may be defective or damaged. Replace each with a new one following the steps in Chapter 4. If the FDD is still not functioning properly, replace the system board with a new one following the steps in Chapter 4. [CONFIDENTIAL] Satellite M100 Series Maintenance Manual 2-22...

  • Page 57: Speaker Troubleshooting

    - see Figure 2-1 Perform earphone test (Procedure 2) Do earphones function correctly? Perform connection check (Procedure 3) Perform replacement check (Procedure 4) Replace system board Figure 2-9 Speaker troubleshooting process [CONFIDENTIAL] Satellite M100 Series Maintenance Manual 2-23...
  • Page 58 If the stereo speakers don't sound properly, the stereo speakers may be defective or damaged. Replace them with new ones. If the stereo speakers still do not work properly, try replacing in turn the audio board and system board. [CONFIDENTIAL] Satellite M100 Series Maintenance Manual 2-24...

  • Page 59: Optical Drive Troubleshooting

    Audio CD functions ok? (Procedure 2) Perform software check (Procedure 3) Perform diagnostic test (Procedure 4) Perform connection and replacement check (Procedure 5) Replace system board Figure 2-10 Optical drive troubleshooting process [CONFIDENTIAL] Satellite M100 Series Maintenance Manual...
  • Page 60 The audio test program stored in the Diagnostics Disk will test the drive’s ability to play an audio CD. See Chapter 3 for details. If any errors occur while executing the diagnostic program, go to Procedure 5. [CONFIDENTIAL] Satellite M100 Series Maintenance Manual...
  • Page 61 Chapter 4, Replacement Procedures. If the drive is still not functioning properly, perform Check 3. Check 3 The system board may be damaged. Replace it with new one following the instructions in Chapter 4, Replacement Procedures. [CONFIDENTIAL] Satellite M100 Series Maintenance Manual...

  • Page 62: Modem Troubleshooting

    (Procedure 1) Check / replace Computer unable to telephone line and detect telephone signal? connections Perform connection check (Procedure 2) Perform replacement check (Procedure 3) Replace system board Figure 2-11 Modem troubleshooting process [CONFIDENTIAL] Satellite M100 Series Maintenance Manual...
  • Page 63 The modem card or RJ-11 jack may be faulty. Try replacing them. If the problem persists, the system board may be defective or damaged. Replace the System Board with a new one following the steps in Chapter 4, Replacement Procedures. [CONFIDENTIAL] Satellite M100 Series Maintenance Manual...

  • Page 64: Pcmcia Troubleshooting

    2.12 PCMCIA Troubleshooting START Perform SYCARD test (Procedure 1) Do errors occur during PCMCIA unit is SYCARD test? not faulty. Perform PCMCIA socket replacement check (Procedure 2) Replace system board Figure 2-12 PCMCIA troubleshooting process [CONFIDENTIAL] Satellite M100 Series Maintenance Manual...
  • Page 65 Disassemble the computer following the steps described in Chapter 4, Replacement Procedures and replace the socket. If the problem persists, the system board may be defective or damaged. Replace the system board with a new one following the steps in Chapter 4. [CONFIDENTIAL] Satellite M100 Series Maintenance Manual...

  • Page 66: Ieee 1394 Troubleshooting

    IEEE 1394 port and transmission are not Was an IEEE 1394 problem detected? faulty. Continue troubleshooting - refer to Figure 2.1 Perform connection and replacement check (Procedure 3) Replace system board Figure 2-13 IEEE 1394 troubleshooting process [CONFIDENTIAL] Satellite M100 Series Maintenance Manual...
  • Page 67 The transmission cable may be damaged. Replace with a good cable. If the malfunction persists, go to Check 4 Check 4 The system board may be damaged. Replace it with a new one following the instructions in Chapter 4. [CONFIDENTIAL] Satellite M100 Series Maintenance Manual...

  • Page 68: Wireless Lan Troubleshooting

    (Procedure 1) Wireless LAN system is not faulty. Continue Was a wireless LAN problem delected? troubleshooting - refer to Figure 2.1 Perform connector and replacement check (Procedure 2) Replace wireless LAN antenna/unit Replace system board [CONFIDENTIAL] Satellite M100 Series Maintenance Manual...
  • Page 69 2.14 Wireless LAN Troubleshooting 2 Troubleshooting Procedures Figure 2-14 Wireless LAN troubleshooting process [CONFIDENTIAL] Satellite M100 Series Maintenance Manual...
  • Page 70 The wireless LAN unit may be damaged. Replace it with a new one following the instructions in Chapter 4. If the problem still exists, perform Check 4. Check 4 The system board may be damaged. Replace it with a new one following the instructions in Chapter 4. [CONFIDENTIAL] Satellite M100 Series Maintenance Manual...

  • Page 71: 5In1 Card Troubleshooting

    Perform 5IN1 CARD test (Procedure 1) Do errors occur during 5IN1 unit is not 5IN1 Card test? faulty. Perform 5IN1 card socket replacement check (Procedure 2) Replace system board Figure 2-15 5IN1 card troubleshooting process [CONFIDENTIAL] Satellite M100 Series Maintenance Manual...
  • Page 72 Disassemble the computer following the steps described in Chapter 4, Replacement Procedures and replace the socket. If the problem persists, the system board may be defective or damaged. Replace the system board with a new one following the steps in Chapter 4. [CONFIDENTIAL] Satellite M100 Series Maintenance Manual...

  • Page 73: Bluetooth Troubleshooting

    (Procedure 1) Bluetooth is not faulty. Was a Bluetooth problem Continue troubleshooting-refer detect? to Figure 2.1 Perform connector and replacement check (Procedure 2) Replace Bluetooth antenna moudle. Replace system board Figure 2-16 Bluetooth troubleshooting process [CONFIDENTIAL] Satellite M100 Series Maintenance Manual...
  • Page 74 The Bluetooth module may be damaged. Replace it with a new one following the instructions in Chapter 4. If the problem still exists, perform Check 4. Check 4 The system board may be damaged. Replace it with a new one following the instructions in Chapter 4. [CONFIDENTIAL] Satellite M100 Series Maintenance Manual...

  • Page 75: Fingerprint Troubleshooting

    2.15 5IN1 Card Troubleshooting 2 Troubleshooting Procedures 2.17 Fingerprint Troubleshooting Figure 2-17 Fingerprint troubleshooting process [CONFIDENTIAL] Satellite M100 Series Maintenance Manual...
  • Page 76 The Fingerprint unit or FPC may be defective or damaged. Replace each with a new one following the steps in Chapter 4. If the FDD is still not functioning properly, replace the system board with a new one following the steps in Chapter 4. [CONFIDENTIAL] Satellite M100 Series Maintenance Manual...
  • Page 77 2.15 5IN1 Card Troubleshooting 2 Troubleshooting Procedures 2.18 3D HDD Protection Troubleshooting START Preform diagnostic test (Procedure 1) Was a 3D sensor 3D functioning properly problem detect? Replace system board Figure 2-18 3D HDD protection troubleshooting process [CONFIDENTIAL] Satellite M100 Series Maintenance Manual...
  • Page 78 Run the Diagnostic Program, which will automatically execute the 3D sensor test. Refer to Chapter 3, Tests and Diagnostics for more information on the program. If an error is not located, the 3D HDD protection system is functioning properly. [CONFIDENTIAL] Satellite M100 Series Maintenance Manual...

  • Page 79: Chapter 3 Tests And Diagnostics

    3.1The Diagnostic Test 3. Tests and Diagnostics Chapter 3 Tests and Diagnostics Satellite M100/TECRA A6 Series Maintenance Manual...

  • Page 80: The Diagnostic Test

    3.15 LAN Test........................3-23 3.16 RTC Test ........................3-26 3.17 Speaker EQ Check&Rewrite..................3-27 3.18 Read 1394 GUID…………...………………………………………………...……..3-29 3.19 6Button Test …………………………………………………………………………..3-30 3.20 Fingerprint DOS Test ……………………..…………………………………………3-31 3.21 3D G-Sensor DOS test ……………………………………………………………….3-33 3.22 Clear Fingerprint Registered…………………………………………………………...3-40 satellite M100/TECRA A6 Series Maintenance Manual...

  • Page 81: The Diagnostic Test

    A formatted working diskette for the floppy disk drive test (Floppy Disk Drive Test) A data CD disc (ODD Test) The following sections explain how to execute the Test & Diagnostic Program and detail the tests within the program. Satellite M100/TECRA A6 Series Maintenance Manual...

  • Page 82: Executing The Diagnostic Test

    L. LCD PIXELS MODE TEST M. MAGNETIC SWITCH TEST N. HDD R/W TEST O. IEEE1394 CODE TEST P. Speaker EQ Check&Rewrite Q. Button test R. Fingerprint DOS Test S. 3D G-sensor DOS Test T. Clear FP(Fingerprint) Registered satellite M100/TECRA A6 Series Maintenance Manual...
  • Page 83 3.2 Executing the Diagnostic Test 3. Tests and Diagnostics The below display will show up at the beginning of T&D program If the test result passes, the following display will show up: Satellite M100/TECRA A6 Series Maintenance Manual...
  • Page 84 If an error is detected and a test fails, the following message displays: Then press any key for next actions – the below display presented if copying test log file onto diskette is necessary. This action will be executed when “Y” key pressed. satellite M100/TECRA A6 Series Maintenance Manual...
  • Page 85 It will skip this process if “N” key pressed. And then it will check if it’s necessary to leave this program. Program will quit when “Y” key pressed and it will go back main menu for next test if “N” key pressed. Satellite M100/TECRA A6 Series Maintenance Manual...

  • Page 86: Display Configuration

    Panel ID HDD type & capacity (Vendor ID. Model .Firmware) VRAM size / VGA CHIP TYPE Battery cell (6cell;9cell;12cell) Wireless type LAN Type (Enkron-R; Vidalia) Bluetooth/FIR/Docking/1394 SKU ID The screen should display as below: satellite M100/TECRA A6 Series Maintenance Manual...

  • Page 87: Dmi Check Test

    SKU data. NOTE: To execute this test, you must input unit Part Number as “Uppercase Character”. The screen should display as below, indicating whether the test is passed or failed after comparison. Satellite M100/TECRA A6 Series Maintenance Manual...

  • Page 88: Speaker Audio Test

    OK within 3 times “Beep” sound generated. NOTE: Remember to tune up the volume as “Maximum” before this test starts. The screen should display as below, indicating whether the test is passed or failed after the question. 3-10 satellite M100/TECRA A6 Series Maintenance Manual...

  • Page 89: Fan On/Off Test

    The computer will stop the fan working after any key pressed. Listen to check if the fan is “OFF” – it means no rotating sound. The screen should display as below, indicating whether the test is passed or failed after the question. Satellite M100/TECRA A6 Series Maintenance Manual 3-11...

  • Page 90: Main Battery Charge Test

    Remain charge capacity (0 ~ 100%) Charge function (PASS/FAIL) - “Battery Is Full” showed when “remain charge capacities” is 100% The screen should display as below, indicating whether the test is passed or failed when finished. 3-12 satellite M100/TECRA A6 Series Maintenance Manual...

  • Page 91: Fdd Test

    NOTE: The write-protected device of this formatted diskette should be “Disable”. The subtests run automatically. NOTE: Press “Esc” key can skip the current subtest. The screen should display as below, indicating whether the subtests pass or fail when finished. Satellite M100/TECRA A6 Series Maintenance Manual 3-13...

  • Page 92: Odd Test

    The ODD test includes two subtests of the: 1. Random read/partial sequential read function 2. Eject ODD door The screen should display as below, indicating whether the subtests pass or fail when finished. 3-14 satellite M100/TECRA A6 Series Maintenance Manual...

  • Page 93: Keyboard Test

    NOTE: The “Fn” key cannot be tested in the keyboard test. To determine whether the “Fn” key is working correctly, press “Fn+F6 ” or “Fn+F7 ” keys to check if LCD display brightness change gradually. Satellite M100/TECRA A6 Series Maintenance Manual 3-15...
  • Page 94 3 Tests and Diagnostics 3.10 Keyboard Test 3-16 satellite M100/TECRA A6 Series Maintenance Manual...

  • Page 95: Mouse (Pad) Test

    The Touch Pad button subtest allows users to test their Touch Pad buttons. If the buttons are clicked, the cursors should appear in the corresponding box of the button figure that is displayed on the screen as below. Satellite M100/TECRA A6 Series Maintenance Manual 3-17...
  • Page 96 It will indicate whether the subtests pass or fail after three questions. NOTE: The above figure has three compartments although the Touch Pad installed may only have two buttons. In this case, the central compartment in the figure does not correspond to any button. 3-18 satellite M100/TECRA A6 Series Maintenance Manual...

  • Page 97: Lcd Pixels Mode Test

    - including 320*200 (4/16/256 colors), 640*200 (2/16 colors), 640*350 (2/16 colors), 640*480 (2/16/256 colors), 800*600 (256 colors) and 1024*768 (256 colors). The screen should display as below, indicating whether the test is passed or failed after the question. Satellite M100/TECRA A6 Series Maintenance Manual 3-19...

  • Page 98: Lid Switch Test

    Follow below steps to run this test: 1. Close the LCD cover. 2. Heard 3 “Beep” sound happened during LCD closed. 3. Open the LCD. Then it will indicate whether the test is passed or failed. 3-20 satellite M100/TECRA A6 Series Maintenance Manual...

  • Page 99: Hdd R/W Test

    After the choice is made, HDD information will show as below: Model name Firmware revision Serial number CHR (Cylinder High Register) mode – including cylinders, heads, sectors and sizes. LBA (Logical Block Addressing) mode – including sectors and sizes. Support Ultra DMA Mode Satellite M100/TECRA A6 Series Maintenance Manual 3-21...
  • Page 100 NOTE: Press “Ctrl + Break” keys can terminate the current subtest. The screen should display as previous picture, indicating whether the subtest is passed or failed when finished. NOTE: The AC adaptor should be connected to successfully run this test. 3-22 satellite M100/TECRA A6 Series Maintenance Manual...

  • Page 101: Lan Test

    And LAN information will show on the test screen: Device Registers FIFOs EEPROM Interrupt Loopback Test (s) The subtests run step by step: (As below) Step1. Select “Test Adapter” Item to press “Enter” key. Satellite M100/TECRA A6 Series Maintenance Manual 3-23...
  • Page 102 3. Tests and Diagnostics 3.15 LAN Test Step2. Select “Begin Adapter Tests” Item to press “Enter” key to begin function testing. The screen should display as below, indicating whether the subtests pass or fail when finished 3-24 satellite M100/TECRA A6 Series Maintenance Manual...
  • Page 103 3.15 LAN Test 3. Tests and Diagnostics Step3. Press [ESC] key to EXIT LAN test MENU. The screen should display as below, Need you select your test result to show “PASS” or “Fail”. Satellite M100/TECRA A6 Series Maintenance Manual 3-25...

  • Page 104: Rtc Test

    Checks the computer’s RTC (Real Time Clock) and calendar functions by comparing the DOS and CMOS values. The test runs automatically. The screen should display as below, indicating whether the test is passed or failed when finished. 3-26 satellite M100/TECRA A6 Series Maintenance Manual...
  • Page 105 The EQ Type test includes two subtests of the: 1. Read EQ Type from EEPROM 2. Re-Write EQ Type to EEPROM NOTE: To execute this test, you must select speaker type (Harman or No brand). The figure below will be displayed: Satellite M100/TECRA A6 Series Maintenance Manual 3-27...
  • Page 106 3. Tests and Diagnostics 3.17 Speaker EQ Test The Item2 figure below will be displayed: NOTE: Write speaker EQ must reboot to enable EQ. 3-28 satellite M100/TECRA A6 Series Maintenance Manual...

  • Page 107: Read 1394 Guid

    This test will check if the computer’s EEPROM 1394GUID code is correct. NOTE: Must open the RAM Door to see RAM connector GUID bar code before test item begins. The figure below will be displayed: Satellite M100/TECRA A6 Series Maintenance Manual 3-29...

  • Page 108: 6Button Test

    Press each of the buttons on the front panel in turn. A yellow bar will appear on the relevant section of the figure if the button passes the test. Press Ctrl +C to quit the test. 3-30 satellite M100/TECRA A6 Series Maintenance Manual...

  • Page 109: Fingerprint Dos Test

    Step2. Need you swipe your finger 2 time to enroll. Step3. Need you swipe your finger 3 time to enroll. Step4. The test program auto compare 1 and 3 finger then to enroll. Satellite M100/TECRA A6 Series Maintenance Manual 3-31...
  • Page 110 3. Tests and Diagnostics 3.20 Fingerprint DOS Test Step5. Need you swipe your finger then test program will verify it. Step6. verify pass, Step7. Need you select your test result to show “PASS” or “Fail”. 3-32 satellite M100/TECRA A6 Series Maintenance Manual...

  • Page 111: G-Sensor Dos Test

    Item Contents Access An access platform is leveling. platform. Test Fixture The Fixture which fixes PC by 90 degree inclination is used. Vibration/shock doesn't take a PCB at the time of T&D inspection. Satellite M100/TECRA A6 Series Maintenance Manual 3-33...
  • Page 112 The display of a test program and the set method of PC are shown below. Display of a Test Program The portion which PC and Test-Fixture contact is green. Set method of PC Upper Judgment If all data is less than ranges, it will be OK. 3-34 satellite M100/TECRA A6 Series Maintenance Manual...
  • Page 113 The display of a test program and the set method of PC are shown below. Display of a Test Program Set method of PC Rear Uppe Judgment If all data is less than ranges, it will be OK. Satellite M100/TECRA A6 Series Maintenance Manual 3-35...
  • Page 114 The display of a test program and the set method of PC are shown below. Display of a Test Program Right Set method of PC Uppe Judgment If all data is less than ranges, it will be OK. 3-36 satellite M100/TECRA A6 Series Maintenance Manual...
  • Page 115 The display of a test program and the set method of PC are shown below. Display of a Test Program Front Set method of PC Uppe Judgment If all data is less than ranges, it will be OK. Satellite M100/TECRA A6 Series Maintenance Manual 3-37...
  • Page 116 Display of a Test Program Set method of PC Left Uppe Judgment If all data is less than ranges, it will be OK. Inspection Judgment If all data is less than ranges, it will be OK. 3-38 satellite M100/TECRA A6 Series Maintenance Manual...
  • Page 117 A test result is displayed when a test is completed. A display of result is O.K. or NG. And an error flag is returned at the end of a program. OK is 0. NG is 1. Satellite M100/TECRA A6 Series Maintenance Manual 3-39...

  • Page 118: Clear Fingerprint Registered

    HWTEST 0 29 0 1 -C " to clear all information in TBX module The subtests run step by step: (As below) Step1: Step2: Display Notice for clear registered. Step3: below information was the utility auto run. 3-40 satellite M100/TECRA A6 Series Maintenance Manual...
  • Page 119 Step5: If you choice “Y”, the system will reboot. If you choice “N”, the system will show Notice again (see be photo). You can press any key to go back test MEMU list. Satellite M100/TECRA A6 Series Maintenance Manual 3-41...
  • Page 120 3. Tests and Diagnostics 3.23 Clear Fingerprint Registered DOS Tools 3-42 satellite M100/TECRA A6 Series Maintenance Manual...

  • Page 121: Replacement Procedures

    Chapter 4 Replacement Procedures [CONFIDENTIAL]...
  • Page 122 4. Replacement Procedures [CONFIDENTIAL] 4-ii Satellite M100 Series Maintenance Manual...

  • Page 123: Optical Drive Module

    USB Board ......................... 4-55 4.21 System Board ......................4-57 4.22 VGA Module ......................4-60 4.23 Fan & CPU ........................ 4-62 4.24 Display Mask ......................4-67 4.25 FL Inverter Board ..................... 4-69 4.26 LCD Module ......................4-72 [CONFIDENTIAL] Satellite M100 Series Maintenance Manual 4-iii...

  • Page 124: Optical Drive

    Removing the Direct Play Button Board............4-26 Figure 4-26 Removing the Direct Play Button Board cable ..........4-26 Figure 4-27 Removing the Bluetooth module screw ............4-28 Figure 4-28 Disconnecting the FFC cable ...............4-28 Figure 4-29 Lifting the Bluetooth module ...............4-29 [CONFIDENTIAL] 4-iv Satellite M100 Series Maintenance Manual...
  • Page 125 Removing the fingerprint module bracket ........... 4-51 Figure 4-58 Removing the fingerprint module..............4-52 Figure 4-59 Removing the speaker screws..............4-53 Figure 4-60 Removing the speakers ................4-53 Figure 4-61 Removing the USB Board screws..............4-55 [CONFIDENTIAL] Satellite M100 Series Maintenance Manual...
  • Page 126 Removing the connectors ................4-69 Figure 4-81 Removing the FL inverter board ..............4-70 Figure 4-82 Removing the LVDS cable screw ..............4-72 Figure 4-83 Removing the LCD Module .................4-72 Figure 4-84 Removing the bracket screws...............4-73 [CONFIDENTIAL] 4-vi Satellite M100 Series Maintenance Manual...

  • Page 127: General

    Wireless LAN Direct Play Bluetooth Memory Button Display Assembly Module Module Module Top Cover Display Mask Fingerprint Touch Pad Speakers USB Module System Board FL Inverter Board Module VGA Module LCD Module Heat sink [CONFIDENTIAL] Satellite M100 Series Maintenance Manual...

  • Page 128: Bluetooth Module

    Wireless LAN Direct Play Bluetooth Memory Button Display Assembly Module Module Module Top Cover Display Mask Fingerprint Touch Pad Speakers USB Module System Board FL Inverter Board Module VGA Module LCD Module Heat sink [CONFIDENTIAL] Satellite M100 Series Maintenance Manual...
  • Page 129 Always use the lithium ion battery pack or a backup battery that is authorized by Toshiba or is compatible with the unit. Since other battery packs have different specifications, they may be incompatible with the unit, and may burst or explode.
  • Page 130 The computer contains many sharp edges and corners, so be careful not to injure yourself. 10. After you have replaced a FRU, make sure the computer is functioning properly by performing the appropriate test on the FRU you have fixed or replaced. [CONFIDENTIAL] Satellite M100 Series Maintenance Manual...
  • Page 131 FRU. After installing an FRU in the computer, confirm that the FRU and the computer are functioning properly. [CONFIDENTIAL] Satellite M100 Series Maintenance Manual...
  • Page 132 Tweezers, to lift out screws that you cannot grasp with your fingers. ESD mats for the floor and the table you are working on. ESD wrist strap or heel grounder. Anti-static carpeting or flooring. Air-ionizers in highly static sensitive areas. [CONFIDENTIAL] Satellite M100 Series Maintenance Manual...

  • Page 133: Battery

    Slide the battery bay latch to release the battery pack and then remove the battery pack from the bay. Figure 4-2 Removing the battery pack NOTE: For environmental reasons, do not throw away a spent battery pack. Please return spent battery packs to Toshiba. [CONFIDENTIAL] Satellite M100 Series Maintenance Manual...
  • Page 134 WARNING: The battery is a lithium ion battery and can explode if not properly replaced, used, handled or disposed of. Use only batteries recommended by Toshiba as replacements. Slide the battery pack into the battery bay. The battery bay latch will click automatically.

  • Page 135: Pc Card

    2. Push the eject button again to pop the PC Card out slightly. 3. Grasp the PC Card and remove it. Figure 4-3 Removing the PC card 4. Push the eject button back into place, if necessary. [CONFIDENTIAL] Satellite M100 Series Maintenance Manual...
  • Page 136 Make sure the eject button does not stick out. Push it back into place if required. Insert the PC Card in the slot and press gently to ensure a firm connection. Figure 4-4 Installing the PC card [CONFIDENTIAL] 4-10 Satellite M100 Series Maintenance Manual...

  • Page 137: Memory Card

    1. Press the memory card gently into the socket until it pops out. Figure 4-5 Pressing the Memory Card 2. Grasp the Memory Card and remove it. Figure 4-6 Removing the Memory Card [CONFIDENTIAL] Satellite M100 Series Maintenance Manual 4-11...
  • Page 138 Inserting the Memory Card To insert the Memory Card, follow these steps: 1. Insert the Memory Card in the slot and press gently to ensure a firm connection. Figure 4-7 Installing the Memory Card [CONFIDENTIAL] 4-12 Satellite M100 Series Maintenance Manual...

  • Page 139: Hdd

    Removing the HDD Module Follow the steps below to remove HDD module: 1. Turn the computer upside down. 2. Release the black M2.5x4 screw to release the HDD door. Figure 4-9 Releasing the HDD door screw [CONFIDENTIAL] Satellite M100 Series Maintenance Manual 4-13...
  • Page 140 Seat the HDD in the HDD case and bracket, and secure it with four M3×3 silver screws. Insert the HDD unit into the HDD slot. Secure the HDD door with a black M2.5x4 screw. [CONFIDENTIAL] 4-14 Satellite M100 Series Maintenance Manual...

  • Page 141: Expansion Memory

    Release the black M2.0x4 screw with RAM door securing the memory module socket cover. Figure 4-12 Releasing the cover screw Slide your fingernail or a thin object under the cover and lift it off. Figure 4-13 Removing the expansion memory module cover [CONFIDENTIAL] Satellite M100 Series Maintenance Manual 4-15...
  • Page 142 Grasp the module and pull it out. Figure 4-15 Removing the expansion memory module CAUTION: Do not touch the connectors on the expansion memory module or on the computer. Debris on the connectors may cause memory access problems. [CONFIDENTIAL] 4-16 Satellite M100 Series Maintenance Manual...
  • Page 143 Fit the module's connectors into the computer's connectors at about a 45-degree angle and press the module carefully to ensure a firm connection. Push the module down so it lies flat. The latches on either side will click into place to secure the module. [CONFIDENTIAL] Satellite M100 Series Maintenance Manual 4-17...

  • Page 144: Optical Drive Module

    Remove the black M2.5x4 screw securing the optical drive module. Figure 4-16 Removing the optical drive screw Use your hand to push the module bracket and then slide the module from the bay. Figure 4-17 Removing the optical drive module [CONFIDENTIAL] 4-18 Satellite M100 Series Maintenance Manual...
  • Page 145 1. Make sure that the expansion memory door is opened and the ODD screw (M2.5x4, black) is removed. 2. Slide the device into the optical drive module bay. 3. Use the black M2.5x4 screw to secure the optical drive module. 4. Replace the expansion memory module cover. [CONFIDENTIAL] Satellite M100 Series Maintenance Manual 4-19...

  • Page 146: Figure

    Figure 4-18 Removing the optical drive bracket NOTE: The small arrow shown on the metal bracket indicates the top side of the optical bracket. Keep this in mind when removing or installing the drive. [CONFIDENTIAL] 4-20 Satellite M100 Series Maintenance Manual...
  • Page 147 1. Position the optical drive bracket plate so that it is aligned with the rear panel of optical drive. 2. Secure the optical drive bracket plate with silver M2.0x2.5. 3. Install the optical drive module into the bay as described in the preceding section. [CONFIDENTIAL] Satellite M100 Series Maintenance Manual 4-21...

  • Page 148: Removing The Strip Cover

    2. Insert a thin tool such as a flat screwdriver into the gap between the strip cover and keyboard to lever the strip cover up. Figure 4-19 Removing the strip cover 3. Remove the strip cover. Figure 4-20 Removing the strip cover [CONFIDENTIAL] 4-22 Satellite M100 Series Maintenance Manual...

  • Page 149: Removing The Keyboard Screws

    4. Remove the two black M2.0x4 black screws securing the keyboard. Figure 4-21 Removing the keyboard screws 5. Push the center of the keyboard, press the tab, and lift the keyboard out, revealing the keyboard cable underneath. Figure 4-22 Removing the keyboard screws [CONFIDENTIAL] Satellite M100 Series Maintenance Manual 4-23...

  • Page 150: Disconnecting The Keyboard Cable

    4 Replacement Procedures 6. Disconnect the keyboard cable from the system board. Figure 4-23 Disconnecting the keyboard cable 7. Lift and remove the keyboard. Figure 4-24 Removing the keyboard [CONFIDENTIAL] 4-24 Satellite M100 Series Maintenance Manual...
  • Page 151 2. Place the keyboard on the top cover, insert under the center tab, and secure it with two black M2.0x4 screws. 3. Set the strip cover and press down to secure the strip cover until the latches engage. [CONFIDENTIAL] Satellite M100 Series Maintenance Manual 4-25...

  • Page 152: Removing The Direct Play Button Board

    1. Remove the Direct Play Button Board by sliding from the clasps. Figure 4-25 Removing the Direct Play Button Board 2. Remove the Direct Play Button Board Cable attached to the system board. Figure 4-26 Removing the Direct Play Button Board cable [CONFIDENTIAL] 4-26 Satellite M100 Series Maintenance Manual...
  • Page 153 To install the Direct Play Button Board, follow the steps below and refer to the figures in the preceding section. 1. Connect the cable to the connector on the system board. 2. Install the Direct Play Button Board in place while securing the clasps. [CONFIDENTIAL] Satellite M100 Series Maintenance Manual 4-27...

  • Page 154: Removing The Bluetooth Module Screw

    Remove the silver M2.0x2.5 screw securing the Bluetooth module to the system board. Figure 4-27 Removing the Bluetooth module screw Disconnect the Bluetooth FFC cable from the system board. Figure 4-28 Disconnecting the FFC cable [CONFIDENTIAL] 4-28 Satellite M100 Series Maintenance Manual...

  • Page 155: Lifting The Bluetooth Module

    4 Replacement Procedures Insert a screwdriver to gently lift the Bluetooth module. Figure 4-29 Lifting the Bluetooth module Remove the Bluetooth module. Figure 4-30 Removing the Bluetooth module [CONFIDENTIAL] Satellite M100 Series Maintenance Manual 4-29...

  • Page 156: Disconnecting The Bluetooth Connector

    4 Replacement Procedures Disconnect the Bluetooth connector (brown) from the module. Figure 4-31 Disconnecting the Bluetooth connector Separate the FFC cable from the Bluetooth module. Figure 4-32 Removing the Bluetooth module cable [CONFIDENTIAL] 4-30 Satellite M100 Series Maintenance Manual...
  • Page 157 Secure the module to the system board using one silver M2.0x2.5 screw. Connect the FFC cable to the module to connect to the system board. Connect the Bluetooth connector (brown) to the module. [CONFIDENTIAL] Satellite M100 Series Maintenance Manual 4-31...

  • Page 158: Removing The Shield Cover Screws

    Remove the battery pack, cables and any optional devices before you start. In addition, remove the keyboard and then follow these steps: 1. Remove the shield cover screws. Figure 4-33 Removing the shield cover screws 2. Take off the shield cover. Figure 4-34 Removing the memory module [CONFIDENTIAL] 4-32 Satellite M100 Series Maintenance Manual...

  • Page 159: Figure

    3. Grasp the module and pull it out. Figure 4-35 Removing the memory module CAUTION: Do not touch the connectors on the memory module or on the computer. Debris on the connectors may cause memory access problems. [CONFIDENTIAL] Satellite M100 Series Maintenance Manual 4-33...
  • Page 160 2. Push the module down so it lies flat. 3. Place the shield cover about a 45-degree angle and push it down so it lies flat on the top of the module. 4. Secure the shield cover with screws. [CONFIDENTIAL] 4-34 Satellite M100 Series Maintenance Manual...

  • Page 161: Removing The Wireless Lan Unit Screw

    1. Remove the black M2.5x4 screw securing the wireless LAN door. Figure 4-36 Removing the wireless LAN unit screw 2. Remove the wireless LAN door. Figure 4-37 Removing the wireless LAN door [CONFIDENTIAL] Satellite M100 Series Maintenance Manual 4-35...

  • Page 162: Removing The Wlan Module Screws

    3. Remove the WLAN module by removing the clips connecting it to the system board. Figure 4-38 Removing the WLAN module screws 4. Detach the two ends of the WLAN antenna (black and white). Figure 4-39 Removing the wireless LAN antenna connectors [CONFIDENTIAL] 4-36 Satellite M100 Series Maintenance Manual...

  • Page 163: Releasing The Wireless Lan Unit

    5. Use your fingers to press the two latches of the LAN unit holder. The LAN unit pops up. Figure 4-40 Releasing the wireless LAN unit CAUTION: Do not touch the connectors on the wireless LAN unit or on the computer. Debris on the connectors may cause malfunction. [CONFIDENTIAL] Satellite M100 Series Maintenance Manual 4-37...
  • Page 164 3. Attach the white antenna to the main connector, and the black antenna to the Aux connector. 4. Use the black M2.5x4 screw to secure the wireless LAN door. [CONFIDENTIAL] 4-38 Satellite M100 Series Maintenance Manual...

  • Page 165: Removing The Modem Cover Screw

    Remove the battery and any optional devices before removing the modem as described in the following instructions: 1. Remove the M2.5x4 screw to release the modem cover. Figure 4-41 Removing the modem cover screw 2. Remove the modem cover. Figure 4-42 Removing the modem cover [CONFIDENTIAL] Satellite M100 Series Maintenance Manual 4-39...

  • Page 166: Removing The Modem Module Screws

    3. Remove two M2.5x4 black screws securing the modem module. Figure 4-43 Removing the modem module screws 4. Disconnect the modem connector from the modem module and carefully lift the unit from its connector. Figure 4-44 Removing the modem module [CONFIDENTIAL] 4-40 Satellite M100 Series Maintenance Manual...
  • Page 167 1. Connect the modem connector on the system board to the modem module. 2. Fit the modem onto its connector and secure it with two black M2.5x4 screws. 3. Replace the M2.5x4 screw to fix the modem cover. [CONFIDENTIAL] Satellite M100 Series Maintenance Manual 4-41...

  • Page 168: Disconnecting Cables

    2. Disconnect the black LCD power (LVDS) cable, Bluetooth cable, and wireless LAN cable from the system board. Figure 4-45 Disconnecting cables 3. Remove two M2.5x6 black screws securing the LCD assembly from the rear side. Figure 4-46 Disconnecting the rear screws [CONFIDENTIAL] 4-42 Satellite M100 Series Maintenance Manual...

  • Page 169: Removing The Front Screws

    4 Replacement Procedures 4. Remove two M2.5x6 screws securing the LCD assembly to the top cover. Figure 4-47 Removing the front screws 5. Remove the LCD assembly. Figure 4-48 Removing the display assembly [CONFIDENTIAL] Satellite M100 Series Maintenance Manual 4-43...
  • Page 170 Feed the wireless LAN module’s antennae wires through the indented track on the system board towards the rear side. Connect the Bluetooth connector to the Bluetooth module. Connect the LCD power cable to the top chassis. Reinstall the keyboard and wireless LAN module. [CONFIDENTIAL] 4-44 Satellite M100 Series Maintenance Manual...

  • Page 171: Removing The Top Cover (Back Panel Screws)

    1. Turn the computer upside down and remove the following 18 screws from the rear panel: • M2.5X6: seven screws • M2.5X8: six screws • M2.5x4: two screws from the HDD compartment • M2.5x16: three screws Figure 4-49 Removing the top cover (back panel screws) [CONFIDENTIAL] Satellite M100 Series Maintenance Manual 4-45...

  • Page 172: Removing The Top Cover (Front Panel Screws)

    Figure 4-50 Removing the top cover (front panel screws) 3. Detach two speaker cables, touch pad FPC cable, and finger print unit FPC cable from the top cover. Figure 4-51 Removing the cables [CONFIDENTIAL] 4-46 Satellite M100 Series Maintenance Manual...

  • Page 173: Removing The Top Cover

    4 Replacement Procedures 4. Lift off the top cover. Figure 4-52 Removing the top cover [CONFIDENTIAL] Satellite M100 Series Maintenance Manual 4-47...
  • Page 174 FFC cable to the system board. Secure the top cover with two M2.5x6 screws, two M2.5x8 screws, and one M2x4 screw. Turn the computer upside down and secure the 18 screws to the rear panel. [CONFIDENTIAL] 4-48 Satellite M100 Series Maintenance Manual...

  • Page 175: Removing The Touch Pad Screw

    1. Remove one M2.5x3 screw securing the Touch Pad Bracket to the rear side of the top cover. Figure 4-53 Removing the touch pad screw 2. Remove the bracket. Figure 4-54 Removing the touch pad bracket [CONFIDENTIAL] Satellite M100 Series Maintenance Manual 4-49...

  • Page 176: Figure

    To install the Touch Pad, follow the steps below and refer to the figures in the preceding section: 1. Turn the top cover upside down and place the Touch Pad and the Touch Pad Bracket in position on top. 2. Secure the Touch Pad bracket with one M2.5x3 screw. [CONFIDENTIAL] 4-50 Satellite M100 Series Maintenance Manual...

  • Page 177: Removing The Fingerprint Module Bracket Screws

    1. Remove two M2.5x2.5 screws securing the Fingerprint Module Bracket to the rear side of the top cover. Figure 4-56 Removing the fingerprint module bracket screws 2. Remove the bracket. Figure 4-57 Removing the fingerprint module bracket [CONFIDENTIAL] Satellite M100 Series Maintenance Manual 4-51...
  • Page 178 To install the Touch Pad, follow the steps below and refer to the figures in the preceding section: 3. Turn the top cover upside down and place the Fingerprint Module and the Fingerprint Module Bracket in position on top. 4. Secure the Fingerprint Module bracket with two M2.5x2.5 screws. [CONFIDENTIAL] 4-52 Satellite M100 Series Maintenance Manual...

  • Page 179: Removing The Speaker Screws

    1. Remove one M2.5x3 screw securing the left speaker to the rear side of the top cover. Remove one M2.5x3 screw securing the right speaker to the rear side of the top cover. M2.5x3 M2.5x3 Figure 4-59 Removing the speaker screws 2. Remove the speakers. Figure 4-60 Removing the speakers [CONFIDENTIAL] Satellite M100 Series Maintenance Manual 4-53...
  • Page 180 To install the speakers, follow the steps below and refer to the figures in the preceding section: 1. Turn the top cover upside down and place the speakers in position on top. 2. Secure the speakers with two M2.5x3 screws. [CONFIDENTIAL] 4-54 Satellite M100 Series Maintenance Manual...

  • Page 181: Removing The Usb Board Screws

    1. Remove two M2.5x4 screws securing the USB board to the system board. Figure 4-61 Removing the USB Board screws 2. Remove the USB board cable. Figure 4-62 Removing the USB Board cable [CONFIDENTIAL] Satellite M100 Series Maintenance Manual 4-55...

  • Page 182: Figure

    To install the USB board, follow the steps below and refer to the figures in the preceding section: 1. Place the USB board in position next to the system board. 2. Connect the USB board cable to the system board. 3. Secure the USB board with two M2.5x4 screws. [CONFIDENTIAL] 4-56 Satellite M100 Series Maintenance Manual...

  • Page 183: Removing The Cable

    1. Remove the DC connector from its socket. Figure 4-64 Removing the cable 2. Remove the two hexagonal VGA screws from the system board. Figure 4-65 Removing the hexagonal screws [CONFIDENTIAL] Satellite M100 Series Maintenance Manual 4-57...

  • Page 184: Figure

    4 Replacement Procedures 4. Remove the system board after making sure that all connectors are removed from their respective sockets. Figure 4-66 Removing the system board [CONFIDENTIAL] 4-58 Satellite M100 Series Maintenance Manual...
  • Page 185 1. Seat the system board in the chassis. Take care to align all the ports and connectors in their respective openings on the chassis. 2. Replace the two hexagonal screws to secure the VGA port. 3. Connect the power connector in its socket. [CONFIDENTIAL] Satellite M100 Series Maintenance Manual 4-59...

  • Page 186: Removing The Vga Module Screws

    1. Turn the system board over and remove the M2.5x6 screw and M2.5x16 screws securing the VGA module to the system board. Figure 4-67 Removing the VGA module screws 2. Remove the VGA module from the system board. Figure 4-68 Removing the VGA module [CONFIDENTIAL] 4-60 Satellite M100 Series Maintenance Manual...

  • Page 187: Removing The Vga Module Heat Sink

    2. Seat the VGA module and secure the module by placing the M2.5x6 and M2.5x16 screws and tightening them. [CONFIDENTIAL] Satellite M100 Series Maintenance Manual 4-61...

  • Page 188: Removing The Heat Sink Screws

    Turn the system board upside down. Remove the four M2.0x4 screws from the heat sink. Figure 4-70 Removing the heat sink screws Lift and remove the heat sink from the system board. Figure 4-71 Removing the heat sink [CONFIDENTIAL] 4-62 Satellite M100 Series Maintenance Manual...

  • Page 189: Removing The Fan Connector

    Removing the fan connector Remove the M2.5x3 screw securing the fan from the top side of the system board. Figure 4-73 Removing the fan screw from the top side of the system board [CONFIDENTIAL] Satellite M100 Series Maintenance Manual 4-63...

  • Page 190: Removing The Fan

    Turn the cam on the CPU socket with a flat-blade screwdriver so that the notch on the cam is aligned with the open side of the CPU socket to unlock the CPU. Figure 4-75 Turning the CPU cam [CONFIDENTIAL] 4-64 Satellite M100 Series Maintenance Manual...

  • Page 191: Removing The Cpu

    4 Replacement Procedures Gently lift out the CPU. Figure 4-76 Removing the CPU [CONFIDENTIAL] Satellite M100 Series Maintenance Manual 4-65...
  • Page 192 Seat the fan module and secure with the M2.5x3 screw on the top side of the system board. Attach the fan connector. Seat the heat sink over the CPU and secure with four screws in the order indicated on the heat sink. [CONFIDENTIAL] 4-66 Satellite M100 Series Maintenance Manual...

  • Page 193: Removing The Display Mask Screws

    Start with the four snaps at the top of the display mask. Continue unsnapping the display mask along the two sides and the bottom edge to remove the display mask. Figure 4-78 Removing the display mask [CONFIDENTIAL] Satellite M100 Series Maintenance Manual 4-67...
  • Page 194 To install the display mask, follow the steps below and refer to the figures in the preceding section. Seat the display mask and secure the snaps on each side. Secure the display mask with four M2.5x6 screws. [CONFIDENTIAL] 4-68 Satellite M100 Series Maintenance Manual...

  • Page 195: Removing The Screws

    Remove one M2.5x4 black screw securing the FL inverter board to the LCD display assembly. Figure 4-79 Removing the screws Disconnect the two connectors on either side of the board. Figure 4-80 Removing the connectors [CONFIDENTIAL] Satellite M100 Series Maintenance Manual 4-69...

  • Page 196: Figure

    4 Replacement Procedures Remove the FL inverter board. Figure 4-81 Removing the FL inverter board [CONFIDENTIAL] 4-70 Satellite M100 Series Maintenance Manual...
  • Page 197 Place the FL inverter board on the LCD module. Secure one M2.5x4 black screw connecting the FL inverter board to the LCD display assembly. Connect the two connectors on either side of the board. [CONFIDENTIAL] Satellite M100 Series Maintenance Manual 4-71...

  • Page 198: Removing The Lvds Cable Screw

    1. Remove the black M2.5x4 screw securing the LVDS cable to the chassis. Figure 4-82 Removing the LVDS cable screw 2. Lift the LCD module from the top chassis. Figure 4-83 Removing the LCD Module [CONFIDENTIAL] 4-72 Satellite M100 Series Maintenance Manual...

  • Page 199: Removing The Bracket Screws

    3. Remove six M2x3 screws securing the LCD module bracket to the LCD module. Figure 4-84 Removing the bracket screws NOTE: If the LCD module malfunctions, remove the LCD cable and LCD bracket. Then replace the whole LCD module unit. [CONFIDENTIAL] Satellite M100 Series Maintenance Manual 4-73...
  • Page 200 M2x3 black screws. Note the L and R markings to make sure that the bracket arms are secured on the correct side. 2. Seat the LCD module with bracket on the chassis. 3. Secure the LVDS cable with the M2.5x4 screw to the chassis. [CONFIDENTIAL] 4-74 Satellite M100 Series Maintenance Manual...

  • Page 201: Appendix A Handling The Lcd Module

    Handling the LCD Module ................. A-1 Appendix B Board Layout ...................... B-1 Appendix C Pin Assignments....................C-1 Appendix D Keyboard Scan/Character Codes ................ D-1 Appendix E Key Layout......................E-1 Appendix F Series Screw Torque List ..................F-1 Appendix G Reliability......................G-1 [CONFIDENTIAL] Satellite M100 Series Maintenance Manual...

  • Page 202: Appendix A Handling The Lcd Module

    LCD cover before securing the module with screws. Do not force the module into place, because stress can affect its performance. Note: The panel’s polarized surface is easily scratched and damaged, so handle it carefully. [CONFIDENTIAL] Satellite M100 Series Maintenance Manual...
  • Page 203 Cleaner 4. If water or other liquid is left on the panel’s surface for a long period, it can change the screen’s tint or stain it. Be sure to quickly wipe off any liquid. [CONFIDENTIAL] Satellite M100 Series Maintenance Manual...
  • Page 204 6. CMOS-LSI circuits are used in the module, so guard against damage from electrostatic discharge. Be sure to wear a wrist or ankle grounding device when handling the module. [CONFIDENTIAL] Satellite M100 Series Maintenance Manual...
  • Page 205 8. Do not store the module at temperatures below its specifications. Cold can cause the liquid crystals to freeze, lose their elasticity or otherwise suffer damage. 9. Do not disassemble the LCD module. Disassembly can cause malfunctions. [CONFIDENTIAL] Satellite M100 Series Maintenance Manual...
  • Page 206 10. If you transport the module, do not use packing material that contains epoxy resin (amine) or silicon glue (alcohol or oxime). These materials can release gas that can damage the panel’s polarization. [CONFIDENTIAL] Satellite M100 Series Maintenance Manual...
  • Page 207 [CONFIDENTIAL] Satellite M100 Series Maintenance Manual...

  • Page 208: Appendix B Board Layout

    Appendix B Appendix B Board Layout B.1 System Board (FRDSY*) Top View Figure B-1 System board (FRDSY*) layout (Top) [CONFIDENTIAL] Satellite M100 Series Maintenance Manual...
  • Page 209 B.2 System Board (FRDSY*) Bottom View Figure B-2 System board (FRDSY*) layout (Bottom) [CONFIDENTIAL] Satellite M100 Series Maintenance Manual...
  • Page 210 Table B-1 System board ICs (top and bottom) Mark Number Name ENE 910 Transformer TI PCI7412 BIOS ROM ICS9LPR325AKLFT Realtek ALC861 [CONFIDENTIAL] Satellite M100 Series Maintenance Manual...

  • Page 211: Memory

    JP11 PCMCIA Conn JP19,JP20 DDRII conn JP28 Mini-Express conn JP25 1394 conn JP24 ODD conn JP27 MDC conn VR conn PJP1 Power core conn PJP2 Battery conn Fingerprint/B conn JP29 5IN1 memory card conn [CONFIDENTIAL] Satellite M100 Series Maintenance Manual...

  • Page 212: Appendix C Pin Assignments

    Pin No. Signal Name VREF DDR_DQ7 DDR_DQ0 DDR_DQ1 DDR_DQ4 DDR_DM0 DDR_DQS0 DDR_DQ0 DDR_DQ5 DDR_DQ6 DDR_DQ2 DDR_DQ3 DDR_DQ12 DDR_DQ13 DDR_DQ8 DDR_DQ14 DDR_DM1 DDR_DQS1# DDR_CLK0 DDR_DQS1 DDR_CLK0# DDR_DQ10 DDR_DQ9 DDR_DQ11 DDR_DQ15 DDR_DQ21 DDR_DQ20 DDR_DQ17 DDR_DQ16 DDR_DQS2# DDR_TS [CONFIDENTIAL] Satellite M100 Series Maintenance Manual...
  • Page 213 DDR_DQ23 DDR_DQ25 DDR_DQ29 DDR_DQ24 DDR_DQ28 DDR_DM3 DDR_DQS#3 DDR_DQS3 DDR_DQ27 DDR_DQ26 DDR_DQ30 DDR_DQ31 DDR_CKE0 DDR_CKE1 DDR_BS#2 DDR_MA12 DDR_MA11 DDR_MA9 DDR_MA7 DDR_MA8 DDR_MA6 DDR_MA5 DDR_MA4 DDR_MA3 DDR_MA2 DDR_MA1 DDR_MA0 DDR_MA10 DDR_BS#1 DDR_BS#0 DDR_RAS# DDR_WE# DDR_CS0 DDR_CAS# [CONFIDENTIAL] Satellite M100 Series Maintenance Manual...
  • Page 214 DDR_DM4 DDR_DQS4 DDR_DQ34 DDR_DQ39 DDR_DQ38 DDR_DQ33 DDR_DQ40 DDR_DQ45 DDR_DQ44 DDR_DQ41 DDR_DQS5# DDR_DM5 DDR_DQS5 DDR_DQ42 DDR_DQ47 DDR_DQ43 DDR_DQ46 DDR_DQ52 A158 DDR_DQ48 DDR_DQ53 A160 DDR_DQ49 DDR_CLK1 DDR_CLK1# DDR_DQS6# DDR_DQS6 DDR_DM6 DDR_DQ51 DDR_DQ50 DDR_DQ55 DDR_DQ54 DDR_DQ56 DDR_DQ60 [CONFIDENTIAL] Satellite M100 Series Maintenance Manual...
  • Page 215 Table C-2 SODIMM I/F pin assignments (200-PIN) (1/4) Pin No. Signal name Pin No. Signal Name VREF DDR_DQ4 DDR_DQ0 DDR_DQ1 DDR_DQ5 DDR_DM0 DDR_DQS0 DDR_DQ0 DDR_DQ6 DDR_DQ2 DDR_DQ7 DDR_DQ3 DDR_DQ12 DDR_DQ13 DDR_DQ8 DDR_DQ9 DDR_DM1 DDR_DQS1# DDR_CLK3 [CONFIDENTIAL] Satellite M100 Series Maintenance Manual...
  • Page 216 DDR_DQ17 DDR_DQ20 DDR_DQS2# DDR_TS DDR_DQS2 DDR_DM2 DDR_DQ22 DDR_DQ18 DDR_DQWE DDR_DQ23 DDR_DQ24 DDR_DQ26 DDR_DQ25 DDR_DQ28 DDR_DM3 DDR_DQS#3 DDR_DQS3 DDR_DQ30 DDR_DQ29 DDR_DQ31 DDR_DQ27 DDR_CKE2 DDR_CKE3 DDR_BS#2 DDR_MA12 DDR_MA11 DDR_MA9 DDR_MA7 DDR_MA8 DDR_MA6 DDR_MA5 DDR_MA4 DDR_MA3 DDR_MA2 [CONFIDENTIAL] Satellite M100 Series Maintenance Manual...
  • Page 217 OTD3 DDR_DQ37 DDR_DQ33 DDR_DQ36 DDR_DQ32 DDR_DQS4# DDR_DM4 DDR_DQS4 DDR_DQ38 DDR_DQ35 DDR_DQ39 DDR_DQ34 DDR_DQ44 DDR_DQ40 DDR_DQ45 DDR_DQ41 DDR_DQS5# DDR_DM5 DDR_DQS5 DDR_DQ42 DDR_DQ43 DDR_DQ47 DDR_DQ46 DDR_DQ48 A158 DDR_DQ49 DDR_DQ53 A160 DDR_DQ52 DDR_CLK2 DDR_CLK2# DDR_DQS6# DDR_DQS6 DDR_DM6 [CONFIDENTIAL] Satellite M100 Series Maintenance Manual...
  • Page 218 Table C-2 SODIMM I/F pin assignments (200-PIN) (4/4) Pin No. Signal name Pin No. Signal Name DDR_DQ51 DDR_DQ54 DDR_DQ50 DDR_DQ55 DDR_DQ60 DDR_DQ56 DDR_DQ61 DDR_DQ57 DDR_DM7 DDR_DQS7# DDR_DQS7 DDR_DQ58 DDR_DQ59 DDR_DQ62 DDR_DQ63 SMBDATA SMBCLK VDDSPD [CONFIDENTIAL] Satellite M100 Series Maintenance Manual...
  • Page 219 JP15 Table C-3 RGB I/F pin assignments (15-pin) Pin No. Signal name Pin No. Signal Name CRT_R_L CRT_G_L CRT_B_L +CRT_VCC DSUB_12 HSYNC_L VSYNC_L DSUB_15 [CONFIDENTIAL] Satellite M100 Series Maintenance Manual...
  • Page 220 JP26 Table C-4 HDD I/F pin assignments (22-pin) Pin No. Signal name Pin No. Signal Name SATA_TXP0 SATA_TXN0 SATA_RXN0 SATA_RXP0 VCC3 VCC3 VCC3 VCC5 VCC5 VCC5 RESERVE [CONFIDENTIAL] Satellite M100 Series Maintenance Manual...
  • Page 221 SD_D9 SD_D6 SD_D10 SD_D5 SD_D11 SD_D4 SD_D12 SD_D3 SD_D13 SD_D2 SD_D14 SD_D1 SD_D15 SD_D0 SD_DREQ SD_IOR# IDE_DIOW# IDE_DIORDY IDE_DDACK# IDE_IRQ IDE_DA1 +5VCD IDE_DA0 IDE_DA2 SW_SD_CS#1 SW_SD_CS#3 SHDD_LED# +5VCD +5VCD +5VCD +5VCD +5VCD +5VCD [CONFIDENTIAL] Satellite M100 Series Maintenance Manual C-10...
  • Page 222 S1_A3 S1_A2 S1_A1 S1_A0 S1_D0 S1_D1 S1_D2 S1_WP S1_CD1# S1_D11 S1_D12 S1_D13 S1_D14 S1_D15 S1_CE2# S1_VS1 S1_IORD# S1_IOWR# S1_A17 S1_A18 S1_A19 S1_A20 S1_A21 +S1_VCC +S1_VPP S1_A22 S1_A23 S1_A24 S1_A25 S1_VS2 S1_RST S1_WAIT# S1_INPACK# [CONFIDENTIAL] Satellite M100 Series Maintenance Manual C-11...
  • Page 223 Table C-6 PC Card I/F pin assignments (68-pin) (2/2) Pin No. Signal name Pin No. Signal Name S1_REG# S1_BVD2 S1_BVD1 S1_D8 S1_D9 S1_D10 S1_CD2# [CONFIDENTIAL] Satellite M100 Series Maintenance Manual C-12...
  • Page 224 Table C-7 Mini-Express I I/F pin assignments (54-pin) Pin No. Signal name Pin No. Signal Name PCI_WAKE +3VS WLAN_DATA WLAN_CLK +1.5VS MINI_CLKREQ CLK_PCIE# CLK_PCIE XMIT_OFF# PLT_RST# PCIE_RXN2 +3VALW PCIE_RXP2 +1.5VS SMBCLK PCIE_TXN2 SMBDATA PCIE_TXP2 USB_N USB_P +1.5VS +3VS [CONFIDENTIAL] Satellite M100 Series Maintenance Manual C-13...
  • Page 225 Table C-8 LVDS I/F pin assignments (30-pin) Pin No. Signal name Pin No. Signal Name DISPOFF# DAC_BRIG +LCDVDD INVT_PWM +LCDVDD +3VS LCD_DATA LCD_CLK TXCLK+ TZCLK+ TXCLK- TZCLK- TXOUT2+ TZOUT1- TXOUT2- TZOUT1+ TXOUT1- TZOUT2+ TXOUT1+ TZOUT2- TXOUT0- TZOUT0+ TXOUT0+ TZOUT0- [CONFIDENTIAL] Satellite M100 Series Maintenance Manual C-14...
  • Page 226 Pin No. Signal Name LUMA_1 CRMA_1 C.12 JP13 Table C-12 RJ11-45 Connector pin assignments (16-pin) Pin No. Signal name Pin No. Signal Name RJ45_PR1+ RJ45_PR1- RJ45_PR2+ RJ45_PR3+ RJ45_PR3- RJ45_PR2- RJ45_PR4+ RJ45_PR4- LINK10_100# ACTIVITY# [CONFIDENTIAL] Satellite M100 Series Maintenance Manual C-15...
  • Page 227 Pin No. Signal name Pin No. Signal Name +USB_VCCC USB20P- USB20P+ C.15 JP27 Table C-15 MDC Connector pin assignments (12-pin) Pin No. Signal name Pin No. Signal Name ACZ_SDOUT 3.3V ACZ_SYNC ACZ_SDIN1 REEST ACZ_BITCLK [CONFIDENTIAL] Satellite M100 Series Maintenance Manual C-16...
  • Page 228 Signal Name ON/OFF BTN_ID MODE PWR_SUSPLED PWR_LED IBNTN KSO17 KSI5 KSI4 KSI3 KSI2 C.17 Table C-17 T/P Connector pin assignments (6-pin) Pin No. Signal name Pin No. Signal Name SW_R SW_L TP_DATA TP_CLK [CONFIDENTIAL] Satellite M100 Series Maintenance Manual C-17...
  • Page 229 Pin No. Signal Name NUM_LED# PADS_LED# CAPS_LED# +3VS KSO15 KSO14 KSO10 KSO11 KSO8 KSO9 KSO13 KSI7 KSO3 KSO7 KSO12 KSI4 KSI6 KSI5 KSO6 KSO5 KSI6 KSI0 KSO1 KSO0 KSI1 KSI2 KSO2 KSO4 +3VS +3VS [CONFIDENTIAL] Satellite M100 Series Maintenance Manual C-18...
  • Page 230 Pin No. Signal name Pin No. Signal Name INTSPK_R1 INTSPK_R2 C.22 PJP2 Table C-22 BATT Connector pin assignments (7-pin) Pin No. Signal name Pin No. Signal Name BATT_S1 ALI/NIMH# AB/I TS_A EC_SMDA EC_SMCA [CONFIDENTIAL] Satellite M100 Series Maintenance Manual C-19...
  • Page 231 Signal name Pin No. Signal Name +3VS USB_N USB_P C.24 JP34 Table C-24 USB Board Connector pin assignments (10-pin) Pin No. Signal name Pin No. Signal Name +5VALW +5VALW USB_EN# USB20_N2 USB20_P2 USB20_N3 USB20_P3 [CONFIDENTIAL] Satellite M100 Series Maintenance Manual C-20...
  • Page 232 +1.8VS +1.5VS +1.8VS +1.5VS +1.8VS +1.5VS +1.8VS +1.5VS +1.8VS +1.5VS +1.8VS +1.5VS +1.8VS +1.5VS +1.8VS +2.5VS +1.8VS +2.5VS +3VS +2.5VS +3VS VGA_CLK +3VS VGA_DATA +5VS LVDSBC- LVDSAC- LVDSBC+ LVDSAC+ LVDSB0- LVDSA0- LVDSB0+ LVDSA0+ [CONFIDENTIAL] Satellite M100 Series Maintenance Manual C-21...
  • Page 233 GRX_N0 PCIE_GTX_ PCIE_MTX_ MRX_P1 GRX_P1 PCIE_GTX_ PCIE_MTX_ MRX_N1 GRX_N1 PCIE_GTX_ PCIE_MTX_ MRX_P2 GRX_P2 PCIE_GTX_ PCIE_MTX_ MRX_N2 GRX_N2 PCIE_GTX_ PCIE_MTX_ MRX_P3 GRX_P3 PCIE_GTX_ PCIE_MTX_ MRX_N3 GRX_N3 PCIE_GTX_ PCIE_MTX_ MRX_P4 GRX_P4 PCIE_GTX_ PCIE_MTX_ MRX_N4 GRX_N4 [CONFIDENTIAL] Satellite M100 Series Maintenance Manual C-22...
  • Page 234 GRX_N6 PCIE_GTX_ PCIE_MTX_ MRX_P7 GRX_P7 PCIE_GTX_ PCIE_MTX_ MRX_N7 GRX_N7 PCIE_GTX_ PCIE_MTX_ MRX_P8 GRX_P8 PCIE_GTX_ PCIE_MTX_ MRX_N8 GRX_N8 PCIE_GTX_ PCIE_MTX_ MRX_P9 GRX_P9 PCIE_GTX_ PCIE_MTX_ MRX_N9 GRX_N9 PCIE_GTX_ PCIE_MTX_ MRX_P10 GRX_P10 PCIE_GTX_ PCIE_MTX_ MRX_N10 GRX_N10 [CONFIDENTIAL] Satellite M100 Series Maintenance Manual C-23...
  • Page 235 PCIE_MTX_ MRX_N12 GRX_N12 PCIE_GTX_ PCIE_MTX_ MRX_P13 GRX_P13 PCIE_GTX_ PCIE_MTX_ MRX_N13 GRX_N13 PCIE_GTX_ PCIE_MTX_ MRX_P14 GRX_P14 PCIE_GTX_ PCIE_MTX_ MRX_N14 GRX_N14 PCIE_GTX_ PCIE_MTX_ MRX_P15 GRX_P15 PCIE_GTX_ PCIE_MTX_ MRX_N15 GRX_N15 CLK_PCIE DDC_CLK CLKPCIE# DDC_DAT CRT_R VGA_TV_LU [CONFIDENTIAL] Satellite M100 Series Maintenance Manual C-24...
  • Page 236 Table C-25 VGA/B I/F pin assignments (200-pin) (5/5) Pin No. Signal name Pin No. Signal Name CRT_G VGA_TV_CR CRT_B VSYNC HYNC PLTRST# SUSP# DVI_DET# ENVDD DVI_SCLK ENBKL DVI_SDATA DVI_TXC+ DVI_TXD1+ DVI_TXC- DVI_TXD1- DVI_TXD0+ DVI_TXD2+ DVI_TXD0- DVI_TXD2- [CONFIDENTIAL] Satellite M100 Series Maintenance Manual C-25...
  • Page 237 [CONFIDENTIAL] Satellite M100 Series Maintenance Manual C-26...
  • Page 238 Appendix D Appendix D Keyboard Scan/Character Codes Table D-1 Scan codes (set 1 and set 2) (1/4) Code set 1 Code set 2 Keytop Note Make Break Make Break ‘ ~ 7 & BkSp [CONFIDENTIAL] Satellite M100 Series Maintenance Manual...
  • Page 239 Table D-1 Scan codes (set 1 and set 2) (2/4) Code set 1 Code set 2 Keytop Note Make Break Make Break Caps Lock ‘ “ Enter Shift (L) No.102 , < . > Shift (R) [CONFIDENTIAL] Satellite M100 Series Maintenance Manual...
  • Page 240 Table D-1 Scan codes (set 1 and set 2) (3/4) Code set 1 Code set 2 Keytop Note Make Break Make Break Ctrl(L) Alt (L) Space ALT (R) Ctrl(R) ← Home ↑ ↓ PgUp PgDn → [CONFIDENTIAL] Satellite M100 Series Maintenance Manual...
  • Page 241 5. * This key corresponds to key No. 42 in a 102-key model. 6. * Refer to Table D-6, No. 124 key scan code. 7. * Refer to Table D-7, No. 126 key scan code. [CONFIDENTIAL] Satellite M100 Series Maintenance Manual...
  • Page 242 Shift key, scan codes are changed as listed below: With left Shift With right Shift Set 1 E0 AA ___________ E0 B6 E0 2A ___________ E0 36 Set 2 E0 F0 12_________ E0 F0 59 E0 12____________ E0 59 [CONFIDENTIAL] Satellite M100 Series Maintenance Manual...
  • Page 243 AA E0 12 E0 2F E0 F0 2F E0 F0 12 Table D-4 Scan codes with Fn keyiI Code set 1 Code set 2 Keytop Make Break Make Break L-CTRL L-ALT ARROW NUMERIC Scrl [CONFIDENTIAL] Satellite M100 Series Maintenance Manual...
  • Page 244 Code set 2 Keytop Make Break Make Break (–) Table D-6 No.124 key scan code Code set 1 Code set 2 Shift Make Break Make Break Prt Sc Common Ctrl + Shift + Alt + [CONFIDENTIAL] Satellite M100 Series Maintenance Manual...
  • Page 245 Table D-7 No.126 key scan code Key top Shift Code set 1 Code set 2 Make Make Pause Common Ctrl *: This key generates only make codes. [CONFIDENTIAL] Satellite M100 Series Maintenance Manual...

  • Page 246: Appendix E Key Layout

    Appendix E Appendix E Key Layout United States (US) Keyboard Figure E-1 US keyboard United Kingdom (UK) Keyboard Figure E-2 UK keyboard [CONFIDENTIAL] Satellite M100 Series Maintenance Manual...
  • Page 247 Spanish (SP) Keyboard Figure E-3 SP keyboard Japanese (JA) Keyboard Figure E-4 JA keyboard [CONFIDENTIAL] Satellite M100 Series Maintenance Manual...
  • Page 248 Korean (KO) Keyboard Figure E-5 KO keyboard Canadian French (CF) Keyboard Figure E-6 CF keyboard [CONFIDENTIAL] Satellite M100 Series Maintenance Manual...
  • Page 249 Portuguese (PO) Keyboard Figure E-7 PO keyboard US-INTE (US/INTE) Keyboard Figure E-8 US-INTE_ALPS keyboard [CONFIDENTIAL] Satellite M100 Series Maintenance Manual...
  • Page 250 German (GR) Keyboard Figure E-9 GR keyboard E.10 French (FR) Keyboard Figure E-10 FR keyboard [CONFIDENTIAL] Satellite M100 Series Maintenance Manual...
  • Page 251 E.11 Chinese (CH) Keyboard Figure E-11 CH keyboard E.12 Swiss-Darfon (SW) Keyboard Figure E-12 Swiss-Darfon keyboard [CONFIDENTIAL] Satellite M100 Series Maintenance Manual...
  • Page 252 E.13 Italian (IT) Keyboard Figure E-13 IT keyboard E.14 Belgian (BE) Keyboard Figure E-14 BE keyboard [CONFIDENTIAL] Satellite M100 Series Maintenance Manual...
  • Page 253 E.15 Arabic (AR-E) Keyboard Figure E-15 AR-E keyboard E.16 Czech (CZ) Keyboard Figure E-16 CZ keyboard [CONFIDENTIAL] Satellite M100 Series Maintenance Manual...
  • Page 254 E.17 Estonian (EST) Keyboard Figure E-17 EST keyboard E.18 Greek (GK) Keyboard Figure E-18 GK keyboard [CONFIDENTIAL] Satellite M100 Series Maintenance Manual...
  • Page 255 E.19 Hebrew (HB) Keyboard Figure E-19 HB keyboard E.20 Hungarian (HG) Keyboard Figure E-20 HG keyboard [CONFIDENTIAL] E-10 Satellite M100 Series Maintenance Manual...
  • Page 256 E.21 Norwegian (NW) Keyboard Figure E-21 NW keyboard E.22 Dutch (DU) Keyboard Figure E-22 DU keyboard [CONFIDENTIAL] Satellite M100 Series Maintenance Manual E-11...
  • Page 257 E.23 Lithuanian (LI) Keyboard Figure E-23 LI keyboard E.24 Russian (RU) Keyboard Figure E-24 RU keyboard [CONFIDENTIAL] E-12 Satellite M100 Series Maintenance Manual...
  • Page 258 E.25 Turkish (TR) Keyboard Figure E-25 TR keyboard E.26 Yugoslavian (YU) Keyboard Figure E-26 YU keyboard [CONFIDENTIAL] Satellite M100 Series Maintenance Manual E-13...
  • Page 259 E.27 Danish (DM) Keyboard Figure E-27 DM keyboard E.28 Slovak (SV) Keyboard Figure E-28 SV keyboard [CONFIDENTIAL] E-14 Satellite M100 Series Maintenance Manual...
  • Page 260 E.29 Swedish (SD) Keyboard Figure E-29 SD keyboard [CONFIDENTIAL] Satellite M100 Series Maintenance Manual E-15...
  • Page 261 [CONFIDENTIAL] E-16 Satellite M100 Series Maintenance Manual...

  • Page 262: Appendix F Series Screw Torque List

    M2.5*3 (silver) 2.0~2.5kgfcm LOG LOW LCD BRK (L/R)- MMCK25050Z0 M2.5*5 2.5~3.0kgfcm LCD COVER LCD BEZEL-LCD MMCK25050Z0 M2.5*5 BRK (L/R)-LCD 2.5~3.0kgfcm COVER MMCK25050Z0 M2.5*5 MDC TO MB 2.0~2.5kgfcm MMCK25050Z0 M2.5*5 2.5~3.0kgfcm SADDLE(R) TO UP SHIELD UP [CONFIDENTIAL] Satellite M100 Series Maintenance Manual...
  • Page 263 SADDLE - 2.5~3.0kgfcm UPPER LOWER - SPK - MMCK25050Z0 M2.5*5 SADDLE - 2.5~3.0kgfcm UPPER LOG LOW-LOG MMCK25050Z0 M2.5*5 2.5~3.0kgfcm LOW -MB - MMCK25050Z0 M2.5*5 2.5~3.0kgfcm UPSHD - UPPER MMCK25050Z0 M2.5*5 LOGLOW - ODD 2.5~3.0kgfcm [CONFIDENTIAL] Satellite M100 Series Maintenance Manual...

  • Page 264: Speakers

    LCD BRK (L/R) - MAAA0015320 1.2~1.5kgfcm nickel) LCD PANEL 2.0*3 ZBL (Black INVERTER - LCD MAAA0015320 1.5~2.0kgfcm nickel) COVER 2.0*3 ZBL (Black LCD CABLE TO MAAA0015320 1.5~2.0kgfcm nickel) COVER MAAA0015320 1.5~2.0kgfcm 2.0*3 ZBL (Black CPU PLATE TO [CONFIDENTIAL] Satellite M100 Series Maintenance Manual...
  • Page 265 PCMCIA SLOT MAA20100302 (M2.0X12 silver) 1.5~2.0kgfcm TO MB LCD HINGE - MACK25080Z0 M2.5X8 4.0~4.5kgfcm HINGE SADDLE LOGIC LOWER - MACK25080Z0 M2.5X8 HINGE SADLE 2.5~3.0kgfcm L/R (BACK SIDE) HDD BREAKET- MMCK25400Z0 M2.5*4 2.5~3.0kgfcm MB- LOG LOW [CONFIDENTIAL] Satellite M100 Series Maintenance Manual...
  • Page 266 RAM DOOR ELAL203C000 M2.5*3.9 (Half thread) 2.5~3.0kgfcm SCREW MMCK20050N0 M2*5 PCMCIA TO MB 1.5~2.0kgfcm ODD CONN TO MMCK20050N0 M2*5 1.5~2.0kgfcm HDD CONN TO MMCK20050N0 M2*5 1.5~2.0kgfcm (M2*4.2+4 THERMAL AMZKM000400 2.0~2.5kgfcm (Screw+Spring) IMS) PLATE TO MB [CONFIDENTIAL] Satellite M100 Series Maintenance Manual...
  • Page 267 [CONFIDENTIAL] Satellite M100 Series Maintenance Manual...

  • Page 268: Appendix G Reliability

    Appendix G Reliability The following table shows MTBF (Mean Time Between Failures) for each component. Table G-1 MTBF Component Time (hours) 50,000 Keyboard 40,000 300,000 Removable FDD 30,000 Optical (DVD/CD) drive 60,000 AC adaptor 60,000 [CONFIDENTIAL] Satellite M100 Series Maintenance Manual...

Table of Contents