2) ต่ อ สายไฟเข้ า ที ่ เ ครื ่ อ งดั ง ต่ อ ไปนี ้
Connect the wiring following picture
เจาะรู ท ี ่ ป ะเก็ น ยางซึ ่ ง อยู ่ ท ี ่ ฐ านเครื ่ อ ง แล้ ว ร้ อ ยสายไฟเข้ า จากด้ า นหลั ง
❑
ปอกสายไฟ แล้ ว ต่ อ เข้ า กั บ สวิ ท ช์ ป ้ อ งกั น ไฟรั ่ ว (ELCB) โดยต่ อ สายด้ า นที ่ ม ี
❑
กระแสไฟไหลผ่ า นเข้ า ทางขั ้ ว L และต่ อ สายด้ า นที ่ ไ ม่ ม ี ก ระแสไฟไหลผ่ า นเข้ า
ทางขั ้ ว N แล้ ว ใช้ ไ ขควงขั น ให้ แ น่ น
น� า สายดิ น ที ่ ป อกสายเรี ย บร้ อ ยแล้ ว ต่ อ เข้ า กั บ จุ ด ต่ อ สายดิ น ที ่ ต ั ว ฐานรองฮี ต เตอร์
❑
ตามรู ป
Punch a hole at the rubber ring on the unit base. Then insert the electric
❑
cable from the back.
Strip the cable and connect to the earth leakage circuit breaker (ELCB).
❑
Connect the line to the terminal L and the NEUTRAL to the N and secure
it tightly with screws.
Connect the stripped ground wire to the ground terminal of the heater base
❑
following the picture.
3) ต้ อ งต่ อ สายไฟให้ ต รงขั ้ ว (L กั บ N) หรื อ บวกกั บ ลบ
Connect the wires to the correct terminals (L and N)
ถ้ า ต่ อ สายผิ ด ขั ้ ว (L, N) จะท� า ให้ เ กิ ด การผิ ด ปกติ ใ นวงจร ซึ ่ ง ในกรณี น ี ้ อ าจท� า ให้ ร ะบบ
❑
การท� า งานของเครื ่ อ งเสี ย หาย หรื อ เกิ ด ไฟฟ้ า ลั ด วงจรได้
Wrong connection of the terminals (L, N) can cause abnormality in the circuit.
❑
In this case, it may damage the working of the unit or cause a short circuit.
4) จะต้ อ งต่ อ สายดิ น เข้ า กั บ ตั ว เครื ่ อ งเสมอ
The shower heater must be always grounded.
ขนาดของสายดิ น ที ่ ใ ช้ ใ นการติ ด ตั ้ ง ดู ร ายละเอี ย ดในตารางหน้ า 14
❑
The size of the ground wire used in the installation, refer to the details on page 14.
❑
วิ ธ ี ต ิ ด ตั ้ ง แท่ ง เหล็ ก สายดิ น HOW TO INSTALL THE GROUND ROD
เลื อ กแหล่ ง ชุ ่ ม ชื ้ น ที ่ จ ะฝั ง เหล็ ก ทองแดง ความยาวของแท่ ง ทองแดง
❑
ต้ อ งไม่ น ้ อ ยกว่ า 90 ซม.
แท่ ง ส� า หรั บ ต่ อ สายดิ น จะต้ อ งฝั ง ลงในพื ้ น ดิ น ไม่ น ้ อ ยกว่ า 70 ซม. จาก
❑
ผิ ว พื ้ น
จะต้ อ งแน่ ใ จว่ า ความต้ า นทานของดิ น จะต้ อ งน้ อ ยกว่ า 100 โอห์ ม
❑
ถ้ า ความต้ า นทานเกิ น 100 โอห์ ม ให้ ฝ ั ง แท่ ง เหล็ ก ลึ ก ลงไป โดยอาจ
❑
ต้ อ งใช้ 2 ถึ ง 3 แท่ ง
Choose a humid area to put the copper electrode.
❑
The minimum length of the copper electrode is 90 cm.
The ground rod must be put under the ground at the minimum
❑
of 70 cm away from the ground surface.
Make sure that the resistance of the ground must not exceed
❑
100 ohms.
If the resistance exceed 100 ohms, it may be necessary to put
❑
two or three electrodes for grounding.
3RPL061602.indd 17
Ground surface
ประมาณ 2 เมตร
About 2 M.
อย่ า งน้ อ ย 70 ซม.
At least 70 cm.
)
อุ ด ด้ า นในด้ ว ยพลาสติ ก เหนี ย ว
Plaseal
13 มม.
20 มม.
165 มม.
15 มม.
เครื ่ อ งมื อ ส� า หรั บ ใช้ ฝ ั ง
Tools for grounding
ผิ ว ดิ น
อย่ า งน้ อ ย 70 ซม.
แท่ ง สายดิ น
At least 70 cm.
Ground rod
ฝั ง แบบเอี ย ง 30 องศา
30 degree in angle
การต่ อ
Connections
1 ม.
1 M.
แบบขนาน
Parallel type
7/18/12 4:08 PM