Advertisement
For extensive use on woodworking, an auxiliary
table of 3 4 inch plywood will prove its worth in
added work area and the protection from shifting
of your work. Fasten the plywood table to the drill
press table with countersunk screws. This auxiliary
table also provides a good surface for mounting a
shaping fence, pivot pins and other similar units.
It affords protection for the drill press table when
drills break through the work piece.
When drilling through wood, a piece of scrap
material under the work piece will eliminate splinter-
ing and mutilation as the drill point breaks through.
Another method of preserving the surface is to
reverse the work piece when the point of drill breaks
through and finish the hole from opposite side.
For drilling to a definite depth, such as a blind
hole, the feed stop nuts may be set to the desired
depth by lowering the drill to a mark on the edge
of the work piece corresponding to the depth of
hole desired.
A straight piece clamped to the table, as a guide
or fence, has many uses, as in drilling several holes
the same distance from an edge or as a guide for
grooving, fluting or milling.
SAFETY:
The work piece should be held securely on the
table, either by clamps, pins, or a vise, to prevent
its turning with the drill. A drill vise is an inex-
pensive means of holding many varieties of work
and is readily adaptable for use with cylindrical
work. The drill vise or a V-block should always
be used for cylindrical work. In any case secure your
work piece as it may break drills and fly off the table.
PARTS LIST
Key
No.
1
2
3
4
5
6
7
8
9
10
1 1
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
Part No.
27415
18413
18212
18414
18415
27727
38617
27217
18604
38632
18512
18120
*X-18I
*X-1407
27623
38628
1851 1
18410
18429
18422
182 I I
27625
27813
*X-277
38422
27130
38623
**I8I29
*X-413
*X-420
*X-605
27812
27627
27631
38881
27628
27629
PART NAME
Spindle Pulley
Spindle & Pulley Sleeve
Pulley Ball Bearing
Inner Snap Ring
Outer Snap Ring
Panel
Panel Screw
Drill Head Frame
Hand Knob
Quill Lock Sleeve
Quill Lock Screw
-Lock Handle aiuLSei Screw
Set Screw No. 10-24 x %Soc. Head Cone Pt.
Allen Wrench 3/32
Lock Handle
Head Lock Sleeve
Knob Lock Screw
Spindle Collar with Set Screw
Washer-Rubber
Washer
Quill Bearing
Quill
Quill Gasket
Cap Screw "4-20 x 1 J/
2
Hex Head
Feed Stop Bracket
Spindle Ass'y.
Chuck
Chuck Key
Hex Nut Jam ^ - 1 6
Hex Nut "4-20
Lock Washer J4 Amer. Std.
Snap Ring
Feed Stop Rod
Feed Stop Adjusting Collar
Spring
Lock Screw
Feed Stop Collar
Key
No.
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
Part No.
*X-170
18513
18421
27814
27632
38790
*X-417
38460
38876
38692
*X-601
*X-309
X-205
38629
18916
27626
27310
18915
27617
38631
*X-565
**X-1467
38390
»X-3609
'X-1400
27219
27717
38633
38627
38626
27621
27622
27340
27350
38211
*X-185
27104
27979
PART NAME
Set Screw 5/ I 6 - 1 8 x Y
2
Soc. Hd. Cone Pt.
Pinion Shaft Retaining Screw
Washer Fibre
Bumper
Threaded Stud
Motor Support Base
Hex Nut 5/16-18
Motor Mount Ass'y Complete
Roll Pin
Rod - Motor Support
Plain Washer 1 I /3 2 I.D. x I I /1 6 O.D.
Mack. Bolt 57 1 6-18i-LSquare Head
Cap Screw 5 / l b - 1 8 - % Hex. Head
Head Lock
Feed Handle Knob
Feed Handle Rod
Hub, Pinion, Spring & Pin Ass'y.
Feed Return Spring
Pin
Quill Lock
Mach. Screw No. 8-32 x % Rd. Head
V-Belt 1/2 x 45 inches long
Motor Pulley with Set Screw
Set Screw 5 / 1 6 - 1 8 x '/
2
Soc. Head
Allen Wrench 5/32
Table
Column Plug
Lock Handle
Table Lock Sleeve
Table Lock
Column for Model 1 0 3 . 2 4 5 2 1 only
Column for Model 1 0 3 . 2 4 5 3 1 only
Base for Model 1 03.2452 1 only
Base for Model 103.24531 only
Base Lock Shoe
Set Screw ^/i~ I 3 x 1 ^ Square Head
Spindle Pulley Ass'y.
Instruction Sheet and Parts List.
For Illustration—See page 6
'Standard hardware items—may be purchased locally.
*Items are regular stock in Sears hardware departments and mail order
houses. May also be ordered as repair parts by part number provided.
This sheet is intended for instruction and repair parts only and is not a packing slip.
The parts shown and listed may include accessories not necessarily part of this tool.
Advertisement
