Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for HP TFT7210R
Summary of Contents for HP TFT7210R
-
Page 1: User Guide
HP TFT7210R User Guide Part Number 349953-002 August 2007 (Second Edition) - Page 2 © Copyright 2003, 2007 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP...
-
Page 3: Table Of Contents
Maintenance ..........................20 Maintenance guidelines ........................... 20 Cleaning the HP TFT7210R ........................20 Storing the HP TFT7210R ......................... 21 Moving a rack with the HP TFT7210R installed ................... 21 Specifications ..........................23 Physical Specifications ..........................23 Environmental Specifications........................23 Removing the rails ........................24 Removing the HP 1U Adjustable Toolless Rails .................... - Page 4 Regulatory compliance notices ..................... 26 Regulatory compliance identification numbers ..................... 26 Federal Communications Commission notice....................26 FCC rating label..........................26 Class A equipment......................... 26 Class B equipment ......................... 26 Declaration of conformity for products marked with the FCC logo, United States only........27 Modifications............................
-
Page 5: Component Identification
Description Function Power On/Off button Powers the monitor on and off. Power Indicator LED Indicates the power states of the HP TFT7210R. • Green—full power • Amber—Sleep mode (on page 11) and Input Signal Out of Range (on page 11) -
Page 6: Installation
High-voltage power cord (10 ft), C13-C14 This kit might contain extra hardware for your convenience. Installing the HP TFT7210R Align the lower edge of the rack template with the top of the previous rack component, and push the tabs in to hold the rack template in place. Mark the rack to indicate where the HP 1U Adjustable Toolless Rails are to be located. - Page 7 Extend the inner slides until they lock into place. Align the HP TFT7210R with the extended inner slides, and pull the release mechanisms toward you while inserting the HP TFT7210R into the rack. WARNING: To reduce the risk of personal injury, release the release mechanisms after pushing the HP TFT7210R slightly forward.
- Page 8 Align the screw holes on the brace rail with the screw holes on the HP 1U Adjustable Toolless Rails. Installation 8...
- Page 9 Secure the brace rail to the HP 1U Adjustable Toolless Rails by inserting three screws and tightening them. Installation 9...
- Page 10 Attach the cable management arm to the rear of the HP TFT7210R with two screws. Route the cables and plug in the HP TFT7210R. Installation 10...
-
Page 11: Operational Overview
Input signal out of range An input signal that is outside the normal range of operation defined by the capabilities of the HP TFT7210R, causes a "Selected resolution is not within recommended range of operation" message to appear for 30 seconds. -
Page 12: Osd Main Menu Functions
OSD main menu functions Auto Setup When selected, the Auto Setup menu activates the Image Control process and performs four functions automatically: • Auto Level—Automatically adjusts the black and white levels of the display • Auto Position—Automatically adjusts the position of the display •... -
Page 13: Horizontal Position
• Exit Within the menu: • Plus (+) moves up a selection. • Minus (-) moves down a selection. • Menu Select activates one of the actions. Horizontal Position When selected, a slider bar appears to allow the adjustment of the display horizontal position. •... -
Page 14: Color Temp
• Plus (+) moves up a selection. • Minus (-) moves down a selection. • Menu Select activates one of the actions. Color Temp The Color Temp menu contains the following choices: • Cool—A Gamma table for Cool temperatures loads all three-color channels •... -
Page 15: Black Level Adjust
RGB Adjust Blue When selected, a slider bar appears to allow the adjustment of the Blue color in the display. • Plus (+) increases the current value. • Minus (-) decreases the current value. • Menu Select accepts the current value and exits the slider bar. Black Level Adjust The Black Level Adjust menu contains the following sub-menus: •... -
Page 16: Languages
• Phase Adjust (on page 16) • Clock Adjust (on page 16) • Exit Within the menu: • Plus (+) moves up a selection. • Minus (-) moves down a selection. • Menu Select activates one of the actions. Phase Adjust When selected, a slider bar appears to allow the adjustment of the analog phase signal. -
Page 17: Osd Settings
OSD Settings The OSD Settings menu contains the following sub-menus: • OSD Position (on page 17) • OSD Size (on page 18) • OSD Timeout (on page 18) • Exit Within the menu: • Plus (+) moves up a selection. •... -
Page 18: Osd Size
OSD Size The OSD Size menu contains the following choices: • OSD Size Normal—Sets the character to normal size • OSD Size Double—Sets the character to double size Within the menu: • Plus (+) moves up a selection and activates that choice. •... - Page 19 • Micro Code Version • Exit OSD main menu functions 19...
-
Page 20: Maintenance
80% of the power strip input rating. • Install the HP TFT7210R near an outlet that you can reach easily. Disconnect the product by grasping the plug firmly and pulling it from the outlet. Never disconnect it by pulling the cord. -
Page 21: Storing The Hp Tft7210R
HP TFT7210R. Repeat steps 2 and 3 to install the other lock plate. Push the HP TFT7210R back into the rack. Insert an M6 screw into the only visible lock plate hole, securing the HP TFT7210R to the rail. Maintenance 21... - Page 22 Repeat step 6 for the other lock plate. Maintenance 22...
-
Page 23: Specifications
Specifications Physical Specifications Parameter Specification Monitor height 34.29 cm (13.5 in) Monitor depth 4.25 cm (1.67 in) Monitor width 39.6 cm (15.59 in) Unit weight 6.12 kg (13.5 lb) Environmental Specifications Feature Specification Operating temperature 5 to 35°C (41 to 95°F) (independent of altitude) Nonoperating temperature -20 to 60°C (-4 to 140°F) -
Page 24: Removing The Rails
Removing the rails Removing the HP 1U Adjustable Toolless Rails Remove the HP TFT7210R. Remove the brace rail assembly. Locate the spring release. Place your hand on the outside of the HP 1U Adjustable Toolless Rail so that you can move the spring release. -
Page 25: Technical Support
Technical support HP contact information For the name of the nearest HP authorized reseller: • In the United States, see the HP US service locator webpage (http://www.hp.com/service_locator). • In other locations, see the Contact HP worldwide (in English) webpage (http://welcome.hp.com/country/us/en/wwcontact.html). For HP technical support: •... -
Page 26: Regulatory Compliance Notices
Regulatory compliance notices Regulatory compliance identification numbers For the purpose of regulatory compliance certifications and identification, this product has been assigned a unique regulatory model number. The regulatory model number can be found on the product nameplate label, along with all required approval markings and information. When requesting compliance information for this product, always refer to this regulatory model number. -
Page 27: Declaration Of Conformity For Products Marked With The Fcc Logo, United States Only
To identify this product, refer to the part, series, or model number found on the product. Modifications The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by Hewlett-Packard Company may void the user’s authority to operate the equipment. Cables Connections to this device must be made with shielded cables with metallic RFI/EMI connector hoods in order to maintain compliance with FCC Rules and Regulations. -
Page 28: Canadian Notice (Avis Canadien)
Machinery Directive 98/37/EEC Compliance with these directives implies conformity to applicable harmonized European standards (European Norms) which are listed on the EU Declaration of Conformity issued by Hewlett-Packard for this product or product family. This compliance is indicated by the following conformity marking placed on the product: This marking is valid for non-Telecom products and EU harmonized Telecom products (e.g. -
Page 29: Japanese Notice
Japanese notice BSMI notice Korean notice Class A equipment Class B equipment Regulatory compliance notices 29... -
Page 30: Disposal Of Waste Equipment By Users In Private Households In The European Union
Disposal of waste equipment by users in private households in the European Union This symbol on the product or on its packaging indicates that this product must not be disposed of with your other household waste. Instead, it is your responsibility to dispose of your waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment. -
Page 31: Power Cord Requirements
Power cord requirements Introduction to power cord requirements The power cord set meets the requirements for use in the country where you purchased the equipment. The voltage selection switch allows you to select the appropriate line voltage for the server. Power cord sets for use in other countries must meet the requirements of the country where you use the server. - Page 32 Country Accredited agency Applicable note numbers United Kingdom United States NOTE: Flexible cord must be <HAR> Type HO5VV-F, 3-conductor, 1.0 mm2 conductor size. Power cord set fittings (appliance coupler and wall plug) must bear the certification mark of the agency responsible for evaluation in the country where it will be used. NOTE: Flexible cord must be Type SVT or equivalent, No.
-
Page 33: Electrostatic Discharge
Electrostatic discharge Preventing electrostatic discharge To prevent damaging the system, be aware of the precautions you need to follow when setting up the system or handling parts. A discharge of static electricity from a finger or other conductor may damage system boards or other static-sensitive devices. -
Page 34: Acronyms And Abbreviations
Acronyms and abbreviations cathode-ray tube light-emitting diode on-screen display red green blue Acronyms and abbreviations 34... -
Page 35: Index
Index installation 6 installation checklist 6 Auto Setup 12 Japanese notice 29 Black Level Adjust 15 Brightness 12 BSMI notice 29 kit contents 6 Korean notices 29 cables, FCC compliance 27 class A equipment 26 languages 16 class B equipment 26 cleaning the unit 20 Clock Adjust 16 maintenance 20... - Page 36 Sleep Mode 11 specifications 23 storing the unit 21 technical support 25 Vertical Position 13 Index 36...