Overview Features • The CMOS video camera provides 2,000,000 effective picture elements (pixels) that can shoot high-definition images to offer superior picture quality. • The camera is compatible with 8 formats, including the Full HD (1080i high definition) video format, which is equivalent to an HD-TV broadcast.
Otherwise, you may get an electric software may damage hardware, the application shock or a fire may occur. program, or the camera. Sony Corporation is not liable for any damage that may occur under these conditions. In case of abnormal operation, contact your authorized...
Locations of Controls Locations of Controls Front Right side Bottom 1 Lens 4 CN901 jack 2 WIDE button 5 Tripod screw hole 3 TELE button When a tripod is used, please use 5 mm ( inches) or less screw to attach it to the camera.
When 12× digital zoom is used, • I/F clear the number of effective picture elements in each Clears the Command buffer of the FCB-H10 camera. direction reduces to and the overall resolution Clearing the buffer can also be carried out from the deteriorates.
Basic Functions Focus • Near Limit Mode Can be set in a range from about 4.5 m (2000) to 1 cm Focus has the following modes, all of which can be set (C000). using VISCA Commands. The focus range is narrowed by excluding the •...
Page 8
Basic Functions AE – Shutter Priority Automatic Exposure Mode The shutter speed can be set freely by the user to a The variety of AE functions, which allow video signal total of 21 steps – 15 high speeds and 6 low speeds. to output the optimum image for subjects from low When the slow shutter is set, the speed can be light conditions to bright light conditions, are...
Page 9
Basic Functions AE – Iris Priority Parameter IRIS (F1.8) GAIN The iris can be set freely by the user to 18 steps F No. between F1.8 and Close. F1.8 18dB The gain and shutter speed are set automatically F1.8 15dB according to the brightness of the subject.
Basic Functions rest should be set to 20%. The range of the Spot AE Back Light Compensation frame is fixed to 5 blocks vertically and 4 blocks horizontally. When the background of the subject is too bright, or when the subject is too dark due to shooting in the AE mode, back light compensation will make the subject appear clearer.
Page 11
Basic Functions Freeze This function captures an image in the field memory of the camera so that this image can be output continuously. Because communication inside the camera is based on V cycle, the captured image is always the one 3V to 4Vs after the sending of a Command.
Basic Functions Eclipse When designing the housing, refer to the dimensional allowance as shown in the figure below. Vibration Specifications Test Method (Random vibration) • Fix the camera at the four fixation points of the base using M2 screws. • Perform the random vibration test under the following conditions in the X, Y and Z directions for 20 minutes in each direction.
Basic Functions Initial Settings and Position Preset The initial values are those set at the factory. Settings for items that will be retained even when the power to the camera is turned off are indicated by a “a,” those that will be lost are indicated by an “×.” Mode/Position Initial settings Custom...
• Start bit : 1 • Stop bit : 1 • Non parity Flow control using XON/XOFF and RTS/CTS, etc., is not supported..............................................1) VISCA is a protocol which controls consumer camcorders developed by Sony. “VISCA” is a trademark of Sony Corporation.
H10 at X. The header of the reply packet from the The basic unit of VISCA communication is called a FCB-H10 assigned address 1 is 90H. The packet from packet (Fig.1). The first byte of the packet is called the the FCB-H10 assigned address 2 is A0H.
Page 20
X0 6Y 03 FF Command buffer full X0 6Y 04 FF Command cancelled X0 6Y 05 FF No socket (to be cancelled) X0 6Y 41 FF Command not executable X = 9 to F: FCB-H10 address + 8, Y = socket number...
Page 21
88 01 00 01 FF 88 01 00 01 FF X = 1 to 7: FCB-H10 address (For inquiry packet) Y = 9 to F: FCB-H10 address +8 (For reply packet) VISCA interface and inquiry ● CAM_VersionInq Returns information on the VISCA interface.
Page 22
Command List VISCA Command/ACK Protocol Command Command Message Reply Message Comments General Command 81 01 04 38 02 FF 90 41 FF (ACK)+90 51 FF Returns ACK when a command has been accepted, and (Example) (Completion) Completion when a command has been executed. 90 42 FF 90 52 FF 81 01 04 38 FF...
Command List VISCA Camera-Issued Messages ACK/Completion Messages Comments Command Messages z0 4y FF Returned when the command is accepted. (y:Socket No.) Completion z0 5y FF Returned when the command has been executed. (y:Socket No.) z = Device address + 8 Error Messages Comments Command Messages...
Page 29
Command List FCB-H10 Block Inquiry Command List Lens control system inquiry commands ..Command Packet 8x 09 7E 7E 00 FF Byte Bit Comments Byte Bit Comments Byte Bit Comments Destination Address Source Address Focus Near Limit (H) 0 Completion Message (50h)
Page 30
Command List Camera control system inquiry commands .. Command Packet 8x 09 7E 7E 01 FF Byte Bit Comments Byte Bit Comments Byte Bit Comments Destination Address OnePush RES 0: Inquiring 1: OK 2: NG WB Mode Source Address Gain Position 0: Auto 1: Indoor 2: Outdoor 3: OnePush 5: Manual 0 Completion Message (50h)
Page 31
Command List Other inquiry commands ......... Command Packet 8x 09 7E 7E 02 FF Byte Bit Comments Byte Bit Comments Byte Bit Comments Destination Address Memory 1: Provided 0: Not Source Address Gamma Mode 0: Normal, 1: Cinema 1, 2: Cinema 2 0 Completion Message (50h) System 1:50/PAL 0:59.94/NTSC Key Lock 1: On 0: Off...
Page 32
Command List Enlargement Function Query Command ....Command Packet 8x 09 7E 7E 03 FF Byte Bit Comments Byte Bit Comments Byte Bit Comments Destination Address Source Address AF Interval Time (H) 0 Completion Message (50h) AF Interval Time (L) Auto Slow Shutter Limit Digital Zoom Position (H) SpotAE Position (X)
Page 33
Command List VISCA Command Setting Values Exposure Control (1/2) Gain 18 dB 15 dB 59.94/NTSC 50/PAL 12 dB Shutter Speed 10000 10000 9 dB 6000 6000 6 dB 4000 3500 3 dB 3000 2500 0 dB 2000 1750 –3 dB 1500 1250 1000...
Page 34
Command List Exposure Control (2/2) Zoom Ratio and Zoom Position (for HD reference) IRIS GAIN Bright F1.8 18 dB Zoom Ratio Position Data D-Zoom Ratio F1.8 15 dB ×1 F1.8 12 dB 0000 ×1.2 F1.8 9 dB 0800 F1.8 6 dB 1000 ×1.9 F1.8...
Page 35
Command List Others AF Activation time 00 to FF AF Interval time 00 to FF Spot AE position (X) 00 to 0F Spot AE position (Y) 00 to 0F R gain 00 to FF B gain 00 to FF Aperture 00 to 0F Register Setting Register No.
Specifications Specifications Effective picture elements Gain Auto/Manual (–3 to +18 dB, 8 Approx. 2,000,000 pixels steps) Video signal HD: 1080i/59.94, 1080i/50, AE control Full Auto/Shutter Priority/Iris 720p/59.94, 720p/50 Priority/Manual/Bright/Spot AE SD: NTSC (CROP), NTSC Exposure compensation (SQUEEZE), PAL (CROP), ± 10.5 dB (15 steps in a unit of 1.5 dB) PAL (SQUEEZE) Backlight Compensation Lens...
Page 37
Specifications Dimensions Front Back Within a depth of 3 mm inches) or less Bottom Within a depth of 5 mm ( inches) (Tripod screw for camera) or less form the bottom surface Within a depth of 3 mm inches) or less form the bottom surface Right side Harness part...
Page 38
Specifications Pin assignment CN901 (DD-285 board) KYOCERA ELCO Co. 04 6240 224 006 848+ Pin No. Name Level CMOS 5V (low: max 0.1 V, high: min 2.4 V) Send Data CMOS 5V (low: max 0.8 V, high: min 2.0 V) Received Data RESET-IN Reset:low (GND), Normal:...