Important Safety Information You MUST read these warnings carefully before installing or using the hob. If you need assistance, contact our Customer Care Department on 08705 727727 Installation affected by heat and should not be stored above or This appliance must be installed and serviced by a below the hob unit.
Contents For the Installer For the User Instructions for the Installer Important Safety Information Installation Description of the Hob Electrical connections Operation Wiring Diagram Maintenance and Cleaning Fault Finding Something Not Working? Commissioning Service and Spare Parts Conversion from Natural Gas to LPG Customer Care Guarantee Conditions This appliance complies with the following...
Operation Hob burners To light a burner: turn the relevant control knob anticlockwise to the maximum position, then push it down to ignite the burner. upon ignition, keep the knob pushed down about 5 seconds. This will allow the "thermocouple" (see diagram, lett.
Maintenance and Cleaning Before any maintenance or cleaning can be carried out, you must DISCONNECT the hob from the electricity supply. The hob is best cleaned whilst it is still warm, as spillage can be removed more easily than if it is left to cool. The Hob Top Regularly wipe over the hob top using a soft cloth well wrung out in warm water to which a little washing up...
Something Not Working? If the hob is not working correctly, please carry out the following checks before contacting your local Zanussi Service Force Centre. IMPORTANT: If you call out an engineer to a fault listed below, or to repair a fault caused by incorrect use or installation, a charge will be made even if the appliance is under guarantee.
* calls to this number may be recorded for training purposes. Guarantee Conditions Zanussi Guarantee conditions We, Zanussi, undertake that if, within 24 months of the * Appliances found to be in use within a commercial date of the purchase, this Zanussi appliance or any part...
Instructions for the Installer Engineers technical data Overall dimensions Width: 580 mm Rear Left Burner (semi rapid) Depth: 510 mm Heat Input 2.0 kW (6824 BTU/HR) Front Left Burner (auxiliary) Cut out dimensions Heat Input 1.0 kW (3412 BTU/HR) Width: 560 mm Depth: 480 mm...
Important safety requirements Location This hob must be installed in accordance with the Gas Safety (Installation and Use) Regulations (Current Edition) The hob may be located in a kitchen, a kitchen/diner or and the IEE Wiring Regulations (Current Edition). bed sitting room, but not in a bathroom, shower room or For appliances installed in the Republic of Ireland please garage.
Installation IMPORTANT: This hob must be installed by a competent person to the relevant Gas Standards. Please, ensure that, once the hob is installed, it is easily accessible for the engineer in the event of a breakdown. WHEN THE HOB IS FIRST INSTALLED Once the hob has been installed, it is important to remove any protective materials, which were put on in the factory.
Building In Building over a cupboard or drawer If the hob is to be installed above a cupboard or drawer it It is also recommended to carry out the electrical will be necessary to fit a heat resistant board below the connection to the hob as shown in diagrams 1 and 2.
Electrical connections Permanent Connection Any electrical work required to install this hob should be carried out by a qualified electrician or In the case of a permanent connection, it is necessary competent person, in accordance with the current that you install a double pole switch between the hob regulations.
Wiring Diagram 1. TAPS IGNITOR SWITCHES 2. IGNITOR UNIT Fault Finding Preliminary Electrical Systems Check SOCKET PLUG (with cover removed) (face view) Earth Wire Green/Yellow Brown Blue START Neutral Wire Isolate appliance Blue and carry out: A: Earth Continuity check. Blue Green Brown...
Page 14
Ignition System / Gas Ignition Check gas supply at Ignitor does not spark burner Check plug top fuse Light burner manually replace if necessary Check by pass Check polarity and simmer earth continuity of supply point Check position of the Check earth continuity electrode of appliance...
Commissioning When the hob has been fully installed it will be necessary to check the minimum flame setting. To do this, follow the procedure below. Turn the gas tap to the MAX position and ignite. Set the gas tap to the MIN flame position then turn the control knob from MIN to MAX several times.