INSTALLATION
AND SERVICE
MUST BE PERFORMED
BY A QUALIFIED
INSTALLER.
IMPORTANT:
SAVE FOR LOCAL ELECTRICAL
INSPECTOR'S
USE.
READ AND SAVE THESE
INSTRUCTIONS
FOR FUTURE
REFERENCE.
Clearances
and Dimensions
1.
Provide adequate clearances between the range and adjacent combustible surfaces.
2.
LocationmCheck location where the ranqe will be installed. Check for proper electrical supply, and the stability of the floor.
3.
Dimensions that are shown must be used. Given dimensions provide minimum clearance. Contact surface must be solid
and level.
RANGE
OVERALL
DIMENSIONS
28 1/8"
......._
3o"---_1..._i
48-1/2"1
/
maximum/
-7
..........
_ I
/
V\ .....
49-1/8"
_
\\
door open
\,,
.29-7/8" ._4_'-,,
maximum**
\_
1//-ttlI
Fig.
1
**Depth is 30-3/8" with door handle
RANGEELECTRICAL
CONNECTIONS
11 dimensionsfor
ectrical outlet location I
re maximum,
j
I -z--_- f[ "Dashedcubed area
1
_ Centedine I shows where the
|
of range I electrical outlet must
|
|
!
I be installedfor flush )|
I -,.i 11,,,_
[..the
wall installation.
J
--
- 4 _
Edge
2-5/8"for models equipped
withwarmer drawers.
3-1/2"for models equipped
with storagedrawers
Fig.
2
FRONT.................
TYPICALCABINETINSTALLATION
SIDE
VIEW
Minimumto
1"÷
wall on either
side of range
above 36" height.
Fig. 3
30"
Minimum
"1
*--
30" ---_
t
Minimumto
1+13"+
18" cabinetson
Maximumdepth
eitherside
for cabinets
Li
l
of range,
above rangetop.
1
O"clearance below cooking top and at rear of range.
*30" MINIMUM CLEARANCE BETWEEN THE TOP OF THE COOKING SURFACE AND THE BOTTOM OFAN UNPROTECTED WOOD OR METAL
CABINET; OR 24" MINIMUM WHEN BOTTOM OF WOOD OR METAL CABINET IS PROTECTED BY NOT LESS THAN 1/4" FLAME RETARDANT
MILLBOARD COVERED WITH NOT LESS THAN NO. 28 MSG SHEET STEEL, 0.015" STAINLESS STEEL, 0.024" ALUMI NUM OR 0.020" COPPER.
0" CLEARANCE
IS THE MINIMUM FOR THE REAR OF THE RANGE. FOLLOW ALL DIMENSION
REQUIREMENTS
PROVIDED ABOVE TO
PREVENT PROPERTY DAMAGE, POTENTIAL FIRE HAZARD,AND
INCORRECT COUNTERTOP AND CABINET CUTS.
TO ELIMINATE THE RISK OF BURNS OR FIRE BY REACHING OVER HEATED SURFACE UNITS, CABINET STORAGE SPACE LOCATED
ABOVE THE SURFACE UNITS SHOULD BE AVOIDED. IF CABINET STORAGE IS TO BE PROVIDED, THE RISK CAN BE REDUCED
BY
INSTALLING A RANGE HOOD THAT PROJECTS
HORIZONTALLY
A MINIMUM OF 5" BEYOND THE BOTTOM OF THE CABINETS.
IMPORTANT
SAFETY
INSTRUCTIONS
• ALL RANGES
CAN TiP
• INJURYTO
PERSONS
COULD RESULT
• INSTALL ANTI-TIP
DEVICE PACKED WITH
RANGE
• SEE INSTALLATION
INSTRUCTIONS
If the information in this manual is not followed
exactly, a fire or electrical shock may result causing property
damage, personal injury or death.
Important Notes to the Installer
•
Read all instructions contained in these installation instructions
before installing range.
•
Remove all packing material from the oven compartments
before connecting the gas & electrical supply to the range.
•
Observe all governing codes and ordinances.
•
Be sure to leave these instructions with the consumer.
Espa_ol - Paginas 5-8
Important Note to the Consumer
Keep these instructions with your owner's guide for future reference.
•
As when using any appliance generating
heat, there are
certain safety precautions you should follow. These are listed
in the Use & Care Guide, read it carefully.
•
Be sure your range is installed and grounded properly by a
qualified installer or service technician.
•
Make sure thewall coverings around the range can withstand
the heat generated by the range.
•
To eliminate the need to reach over the surface elements,
cabinet storage space above the elements should be avoided.
Serial Plate Locations:
Serial
Serial plate is located on the lower right front frame of the appliance.
Alternate location may be under cooktop.
pin 316454921