Page 1
Above the Co kt p Ove Model JVM2052 BEFORE YOU BEGIN Reed these instructions completelg end carefullg. Note to Consumer - Keep these instructions for future reference. • IMPORTANT- Sovethese Skill level - Instollotion of this opplionce requires bosic...
Installation Instructions CONTENTS Recirculating ..........:19-22 Attach Mounting Plate to Wall ....:19 General information Preparation of Top Cabinet ...... : 19 Important Safety Instructions ........3 Adapt Microwave Oven Blower Electrical Requirements ..........3 for Recirculation ........2 0 Hood Exhaust ..............4 -5 Mount the Microwave Oven ......
Installation Instructions IMPORTANT SAFETY INSTRUCTIONS ELECTRICAL A quQlified electrician must perform a ground continuity check on the wall receptacle before beginning the REQUIREMENTS installQtion to ensure thQt the outlet box is properly grounded. If not properly grounded, or if the wall receptacle does not meet electrical requirements noted Product rating is 120 volts AC, 60 Hertz, 14 amps end (under ELECTRICAL REQUIREMENTS), a quQlified electriciQn...
Installation Instructions HOOD EXHAUST NOTE: Read thesenexttwo pagesonlgif gou plantoventgourexhausttothe outside. If gou planto recirculate theair back into theroom,proceedto page 6. OUTSIDE TOP EXHAUST (EXAMPLE ONLY} The following chart describes an example of one possible ductwork installation. EQUIVALENT NUMBER EQUIVALENT DUCT PIECES LENGTH USED...
Installation Instructions NOTE: If gou need to install ducts, note that the total duct Maximum duct length: length of 5W' x 10" rectangular or 6" diameter round duct For satisfactory air movement, the total duct length should not e×ceed 120 equivalent feet. of 3V_"x 10"...
Installation Instructions PARTS INCLUDED DAMAGE- SHIPMENT/ INSTALLATION ADDITIONAL PARTS • If the unit is damaged in shipment, return the unit PART QUANTITY to the store in which it was bought for repair or replacement. • If the unit is damaged by the customer, repair or pperCabinet ÷...
Installation Instructions TOOLS YOU WILL NEED Ruleror tapemeasure Flatbladescrewdriver Carpentersquare Phillipsscrewdriver aightedge (optional) Pencil Level Tin snips(for cutting damper,if required) Electricdrill with r½,, a ndr¼,, w ood drill bits andr_?,and_½" d rill bits Scissors (to cut template, if necessary) Fillerblocksor scrap wood pieces,if needed for top cabinetspacing Gloves...
Installation Instructions I-IPLACEMENT OF THE MOUNTING PLATE REMOVING THE MICROWAVE FINDING THE WALL STUDS OVEN FROM THE CARTON/ REMOVING THE MOUNTING PLATE Remove the installation instructions, filters, glass tray and the small hardware bag. Do not remove the Styrofoam protecting the front of the oven. Wall Studs Fold back all 4 carton flaps fully against carton sides.
Installation Instructions DETERMINING WALL PLATE LOCATION UNDER YOUR CABINET Plate position - beneath framed recessed Plate position - beneath flat bottom cabinet cabinet bottom Mounting Plate Tabs MountingPlateTabs -Touching the Cabinet Bottom Touching the Back Frame 30" to Cooktop At least 30", up to 36" Plate position - beneath...
Installation Instructions ALIGNING THE WALL PLATE Hole B Drawa Vertical Lineon Wall HoleC Centerline from Centerof Notches TopCabinet 0000000 0000000 AreaE HoleD A CAUTION: Weor gloves to avoid cutting fingers on sharp edges. Draw a vertical line on the wall at the center of the A WAR NING: Risk ofElectric Shock.
Installation Instructions INSTALLATION TYPES IChoose A, B or C) NOTE:This microwave oven is shipped assembled for Outside This microwave oven is designed for adaptation Top Exhaust (except for non-vented models). Select the tgpe to the following three tgpes of ventilation: of ventilation required for gour installation and proceed to A.
Installation Instructions USE TOP CABINET TEMPLATE FOR MOUNT THE MICROWAVE OVEN PREPARATION OF TOP CABINET You need to drill holes for the top support screws, a hole large enough for the power cord to fit through, and a cutout large enough for the exhaust adaptor. CAUTIO N: TO avoid the risk of personal injurg...
Page 14
Installation Instructions MOUNT THE MICROWAVE OVEN {cont.) Dan_er Use the power supplg cord clomp to bundle the power supplg cord. Instoll the power supplg cord clomp, using o screw os shown, to the inside of the cobinet. CabinetFront CabinetBottomShelf FillerBlock to Depth of Cabinet quivalent...
Page 15
Installation Instructions [- OUTSIDE BACK EXHAUST {Horizontal Duct) INSTALLATION OVERVIEW BI. Prepare Rear Wall B2. Attach Mounting Plate to Wall B3. Prepare Top Cabinet B4. Adjust Blower BS. Mount the Microwave Oven PREPARE THE REAR WALL FOR OUTSIDE BACK EXHAUST You need to cut an opening in the rear wall for outside exhaust.
Installation Instructions ATTACH THE MOUNTING PLATE USE TOP CABINET TEMPLATE FOR TO THE WALL PREPARATION OF TOP CABINET You need to drill holes for the top support screws and a hole large enough for the power cord to fit through. Attach the plate to the wall using toggle bolts.
Page 17
Installation Instructions Reattach the blower plate to the cabinet so J--_ ADAPT MICROWAVE OVEN the exhaust ports and blower plate opening BLOWER FOR OUTSIDE BACK are aligned. Attach with 2 blower unit mounting EXHAUST (cont.) screws and then ] blower plate mounting screws. Blower p late Carefully pull out the blower unit.
Installation Instructions MOUNT THE MICROWAVE OVEN Dan_er Use the power supplg cord clamp to bundle the power supplg cord. Install the power supplg cord clamp, using a screw as shown, to the inside of -&CAUTIO N: To °void t herisk of the cabinet.
Installation Instructions IC-1RECIRCULATING (Non-Vented Ductless) INSTALLATION OVERVIEW C1. Attach Mounting Plate to Wall C2. Prepare Top Cabinet C3. Adjust Blower C4. Mount the Microwave Oven C5. Install Charcoal Filter Place the mounting plate against the wall and insert ATTACH THE MOUNTING PLATE the toggle wings into the holes in the wall to mount TO TH E WALL...
Installation Instructions ADAPT MICROWAVE OVEN BLOWER FOR RECIRCULATION Remove and save ] blower plate screws and 2 blower unit mounting screws. Blower p late mounting screw ..! (3 screws) _--_Blower plate Blower u nit Bacl<plate Iowe[ unit NOTE:Make sure wires remain routed in the grooves '",_ raountlngscrew of the motor frame.
Installation Instructions Use the power supply cord clomp to bundle the MOUNT THE MICROWAVE OVEN power supply cord. Instoll the power supply cord clomp, using o screw os shown, to the inside of the cobinet. Cabinet Front Cabinet Bottom Shelf PF1_ FillerBlock /!!ll...
Page 22
Installation Instructions ICSl INSTALLING THE CHARCOAL FI LTER Remove 2 screws on the top front of the grille using a Phillips screwdriver. Open the door. Remove the grille, pulling it straight off. Charcoal Filter Install the charcoal filter. When properlu installed, the wire mesh of the filter should be visible from the front.
Installation Instructions BEFORE YOU USE YOUR MICROWAVE OVEN Make sure the microwave oven has been Read the Owner's Manual. installed according to instructions. KEEP INSTALLATION INSTRUCTIONS FOR THE LOCAL INSPECTOR'S USE. Remove all packing material from the microwave oven. Install turntable and ring in cavitg. Replace house fuse or turn breaker back on.