Page 1 “Troubleshooting” on page 177 in this guide. Owner's Record The model number and serial number are on the back and side of your television. Record these numbers, whenever you communicate with your Toshiba dealer about this Television. Model name: Serial number: Register your Toshiba Television at register.toshiba.com...
Page 2: Child Safety
CHILD SAFETY: PROPER TELEVISION PLACEMENT MATTERS TOSHIBA CARES • Manufacturers, retailers and the rest of the consumer electronics industry are committed to making home entertainment safe and enjoyable. • As you enjoy your television, please note that all televisions – new and old- must be supported on proper stands or installed according to the manufacturer’s recommendations.
Page 3: Safety Precautions
Dear Customer, WARNING (for 84L9300 Series) Thank you for purchasing this Toshiba LED TV. This apparatus has been designed with Class I This document will help you use the many exciting construction and must be connected to a mains features of your new LED TV. Before operating your socket outlet with a protective earthing connection LED TV, carefully read this manual completely.
Page 4 Installation, Care, and Service 13) Unplug this apparatus during lightning storms or when unused for long periods of time. Installation 14) Refer all servicing to qualified service personnel. Servicing is required when the Follow these recommendations and precautions and apparatus has been damaged in any way, such heed all warnings when installing your TV: as power-supply cord or plug is damaged, liquid WARNING: NEVER expose batteries...
Page 5 58”/ 65” 84” Care For better performance and safer operation of your Mounting screws TOSHIBA TV, follow these recommendations and precautions: 35) If you use the TV in a room whose temperature is Fall-prevention band Mounting screw Fall-prevention bands 32° F (0° C) or below, the picture brightness may 27) The apparatus shall not be exposed to dripping or vary until the LCD warms up.
Page 6 If these sounds become frequent or continuous, CAUTION: Four or more people are required for unplug the power cord and contact a Toshiba installation to avoid injury or damage to the TV. Authorized Service Provider.
Page 7 1) This process will require 2 or more people. only. Please note that any commercial use of the 3D Toshiba recommends using 3 people for this function or content provided on your TV could lead process. One person on each side of the TV and to copyright infringement of authors’...
Page 8 • Avoid using the 3D function when under the • For 58L9300U Series: Use the 3D glasses in the influence of alcohol. following viewing angle. • If you are ill or feel ill, you should refrain from Otherwise, you may not see the correct 3D image.
Page 9 Note: This equipment has been tested and found • (For 58L9300U Series) If you use any device, to comply with the limits for a Class B digital device, such as a mobile phone or mobile wireless pursuant to Part 15 of the FCC Rules.
Page 10 • ActiveX is a registered trademark of the Microsoft Caution: Changes or modifications to this equipment Corporation. not expressly approved by Toshiba could void the • Android is a trademark of Google Inc. user's authority to operate this equipment. • Manufactured under license from Wireless Radio Audyssey Laboratories, Inc.
Page 11 Portions © UEI 2000-2012. laws, this guide cannot be reproduced in any form without the prior written permission of Toshiba. No patent liability • Wi-Fi is a registered mark of the Wi-Fi Alliance. is assumed, however, with respect to the use of the •...
Page 12: Table Of Contents
Contents Chapter 1: Introduction ...........20 Safety icons ............... 20 Features ..............21 Overview of installation, setup, and use ....22 TV front and side panel controls and connections ..24 Front panel ............24 Left side ............... 25 TV back panel controls and connections ....26 Back panel controls ..........
Page 13 Contents About the connection illustrations ....... 32 Connecting an antenna, satellite receiver, and/or cable TV box ............32 ® Connecting DVD to ColorStream or VCR to composite video ..........34 Connecting remote IR devices ........35 Using the IR blaster OUT terminal ....... 35 Connecting a digital audio system ......
Page 14 Contents Chapter 4: nitial Setup and Menu ........55 Initial setup ............... 55 Performing the initial setup ......... 56 Navigating the menu system ....... 65 Quick Menu ............66 Chapter 5: Setting up your TV .........67 How to navigate the menu ......... 67 Changing initial settings ........
Page 15 Contents Entering a new PIN code ........89 Changing or deleting your PIN code ....89 Forgotten PIN code ..........90 Using parental controls ..........90 Blocking TV programs and movies by rating (V-Chip) ............90 Downloading an additional rating system .... 91 Displaying ratings ..........
Page 16 Contents Adjusting the picture ..........112 Selecting the picture mode ........ 112 Adjusting the picture quality ......113 Using the advanced picture settings features ..114 Resolution+ ............114 Dynamic Contrast ..........114 ® DynaLight ............114 ® ClearScan ............115 MPEG NR ............
Page 17 Contents ® Using Audyssey Dynamic Volume ....126 Audyssey ABX™ ..........126 Using the surround sound feature ..... 126 Chapter 8: Advanced features ........127 Using your home network ........127 When using a Wireless network connection ..128 Setting up the Network ..........129 Wireless Setup ..........
Page 18 Contents Chapter 9: Cloud TV Companion Apps ......174 Using Apps on a Tablet or Smart phone ....174 Apps Control Profile ..........175 Pairing ..............176 Chapter 10: Troubleshooting ...........177 General troubleshooting .......... 177 Picture problems ............. 178 Sound problems ............180 Remote control problems ........
Page 19 Contents Wireless connection ..........188 Ethernet ............. 188 USB ..............188 SD card .............. 188 Dimensions with table stand ........188 Weight (mass) with stand ........189 Operating conditions ..........189 Supplied accessories ..........189 ™ Acceptable signal formats for PC IN, and HDMI and 3D ..............
Page 20: Chapter 1: Introduction
Chapter 1 Introduction Safety icons This manual contains safety instructions that must be observed to avoid potential hazards that could result in personal injuries, damage to your equipment, or loss of data. These safety cautions have been classified according to the seriousness of the risk, and icons highlight these instructions as follows: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
Page 21: Features
Introduction Features Features Integrated digital tuning (8VSB ATSC and QAM) — ❖ Eliminates the need for a separate digital converter set-top box (in most cases). 3840 x 2160 display resolution. ❖ Quad FHD— Allows you to enjoy high quality full HD pictures ❖...
Page 22: Overview Of Installation, Setup, And Use
Introduction Overview of installation, setup, and use standard colors, see “ColorMaster™” on page 116. ® ClearScan —Technology uses both frame interpolation technology ❖ and advanced backlight control with image synchronization to quadruple the TV refresh rate for an even clearer fast motion video. ®...
Page 23: Limited Warranty
❖ allow proper ventilation. Inadequate ventilation may cause overheating, which will damage the TV. THIS TYPE OF DAMAGE IS NOT COVERED UNDER THE TOSHIBA LIMITED WARRANTY. Do not plug in any power cords until after you have connected all cables and devices to your TV.
Page 24: Tv Front And Side Panel Controls And Connections
“Ambient Light Sensor” on page 116. Remote Sensor—Point the remote control toward this remote sensor, see “Remote control effective range” on page 3D IR—This sensor detects the 3D IR (for 58L9300U model only).
Page 25: Left Side
Introduction TV front and side panel controls and connections Left side Analog Video Port—Analog Video input. Connect using a commercially available conversion cable. ™ 3 HDMI Ports—High-Definition Multimedia Interface input receives digital audio and uncompressed digital video from an ™ HDMI device or uncompressed digital video from a DVI device.
Page 26: Tv Back Panel Controls And Connections
Introduction TV back panel controls and connections TV back panel controls and connections 58” FOR SERVICE USE ONLY POWER button Volume up Volume down Switches the function of VOL+/- buttons to select volume, channel, or input mode. PC / HDMI ™ Audio IN Antenna / Cable PC IN PC/HDMI 2...
Page 27: Back Panel Controls
Introduction TV back panel controls and connections 84” FOR SERVICE USE ONLY POWER button Volume up Volume down Switches the function of VOL+/- buttons to select volume, channel, or input mode. PC / HDMI ™ Audio IN Antenna / Cable PC IN PC/HDMI 2 AUDIO...
Page 28: Back Panel Connections
Introduction TV back panel controls and connections The mode of the VOL +/– buttons change in the following order each time the button is pressed: → Channel → Input → Volume → Back panel connections LAN IN—Connects the TV to your home network. ™...
Page 29: Chapter 2: Connecting Your Tv
Chapter 2 Connecting Your TV Overview of cable types Before purchasing cables, know the connector types your devices require. You can purchase cables from most stores that sell audio/video devices. Coaxial cable (F-type) (Sample Illustration) Coaxial cable Coaxial (F-type) cable connects your antenna, cable TV service, and/or cable converter box to the ANT/CABLE input on your TV.
Page 30: Component Video Cables (Red/Green/Blue)
Component video cables come in sets of three and are for use with video ® devices with component video output. (ColorStream is Toshiba’s brand of component video.) These cables are typically color-coded red, green, and blue. Separate audio cables are required for a complete connection.
Page 31: Optical Audio Cable
Connecting Your TV Overview of cable types Optical audio cable (Sample Illustration) Optical audio cable ® Optical audio cable connects receivers with Dolby Digital or PCM (pulse-code modulation) optical audio input to the TV’s Digital Audio Out terminal, see “Connecting a digital audio system” on page Analog RGB (15-pin) computer cable (Sample Illustration) Analog RGB (15-pin) computer cable Analog RGB (15-pin) computer cable connects a computer to the TV’s...
Page 32: Lan Cable
Connecting Your TV Connecting an antenna, satellite receiver, and cable TV box LAN cable (Sample Illustration) LAN cable Standard LAN cable connects the TV to your home network, see “Connecting the TV to a home network with an Internet connection - wired”...
Page 33 Connecting Your TV Connecting an antenna, satellite receiver, and cable TV box Items needed: Coaxial cables ❖ Standard AV cables ❖ Component video cables (red/green/blue) ❖ NOTE When you use a cable box, you may not be able to use the remote control to program or access certain features on the TV.
Page 34: Connecting Dvd To Colorstream ® Or Vcr To Composite Video
Connecting Your TV ® Connecting DVD to ColorStream or VCR to composite video ® Connecting DVD to ColorStream or VCR to composite video Standard A/V cable Yellow White Red Green Blue TV back panel VIDEO AUDIO AUDIO L / MONO P VIDEO DVD player COMPONENT VIDEO...
Page 35: Connecting Remote Ir Devices
Connecting Your TV Connecting remote IR devices To view antenna or Cable channels: Select the ANT/CABLE video input source on the TV.* To view the DVD player: ® Turn ON the DVD player. Select the ColorStream HD video input source on the TV.* To view satellite programs using the component video connections: ®...
Page 36 Connecting Your TV Connecting remote IR devices To connect the IR blaster cable: Locate the infrared sensor on the front of your device. This sensor is marked on some devices. If you are having issues locating the device's infrared sensor, see “If you cannot locate the device’s infrared sensor:”...
Page 37 Connecting Your TV Connecting remote IR devices To control the device(s): Point the TV remote control toward the front of the TV and press the button for the desired function. The signal passes from the remote control through the TV to the device via the IR Blaster cable. For more information, see “Setting the IR Blaster”...
Page 38: Connecting A Digital Audio System
Connecting Your TV Connecting a digital audio system Connecting a digital audio system ® The TV’s Digital Audio Out terminal outputs a Dolby Digital or 2-channel down-mixed PCM (pulse-code modulation) signal for using ® with an external Dolby Digital decoder or other external audio systems with optical audio input.
Page 39: Connecting An Hdmi™ Or Dvi Device To The Hdmi™ Input
Connecting Your TV Connecting an HDMI™ or DVI device to the HDMI™ input ™ ™ Connecting an HDMI or DVI device to the HDMI input ™ The HDMI input on your TV receives digital audio and uncompressed ™ digital video from an HDMI source device, or uncompressed digital video from a DVI (Digital Visual Interface) source device.
Page 40 Connecting Your TV ™ ™ Connecting an HDMI or DVI device to the HDMI input TV back panel HDMI IN HDMI device (satellite or cable box, media player, etc) HDMI OUT HDMI cable DVI device HDMI -to-DVI adapter cable DVI/HDCP Analog audio cable PC/HDMI 2 AUDIO...
Page 41: Using The Tv Remote And Hdmi ™ Cec Control To
CEC Control functions” on page Configure the connected devices. See each device’s operation ❖ manual. NOTE This feature is limited to models incorporating Toshiba’s HDMI™ CEC Control feature. However, Toshiba is not liable for those operations. See the individual instruction manuals for compatibility information.
Page 42: Connecting An Hdmi ™ Audio System
Connecting Your TV ™ Connecting an HDMI audio system When using an external AV amplifier the picture and sound may not be properly synchronized. In this case, adjust the delay time of the sound on the AV amplifier. NOTE The control range of the delay time differs according to the device you use. ™...
Page 43: Connecting A Computer
Connecting Your TV Connecting a computer Connecting a computer ™ With either the PC IN or HDMI connection, you can view your computer’s display on the TV and hear the sound from the TV’s speakers. Connecting a computer to the TV’s PC IN terminal When connecting a computer to the PC IN terminal on the TV, use an analog RGB (15-pin) computer cable and a PC audio cable.
Page 44: Connect A Computer To The Tv's Hdmi
Connecting Your TV Connecting a computer Some computer models cannot be connected to this TV. ❖ If the computer has a compatible mini D-sub15-pin terminal, an ❖ adapter is not required. Depending on the content’s title and the computer’s specifications, ❖...
Page 45: Connecting To A Home Network
(i.e. no overscanning). Connecting to a home network The LAN port allows your Toshiba TV to connect to your home network. You can use this home network to access photos, movies, and music files that are stored on a connected media server and play them on your TV.
Page 46: Connecting The Tv To A Home Network Without An Internet Connection
Connecting Your TV Connecting to a home network Connecting the TV to a home network without an Internet connection Items needed: Standard LAN cables ❖ Router with a hub ❖ Router with a hub Computer TV back panel Computer (Sample Illustration) L9300U Series—Connecting a network without Internet connection...
Page 47: Connecting The Tv To A Home Network With An Internet Connection - Wired
Connecting Your TV Connecting to a home network Connecting the TV to a home network with an Internet connection - wired Items needed: Coaxial or telephone cable (depending on your modem type) ❖ Standard LAN cables ❖ Router with Hub ❖...
Page 48: Connecting The Tv To A Home Network With An Internet Connection - Wireless
Connecting Your TV Connecting to a home network Connecting the TV to a home network with an Internet connection - wireless Items needed: Coaxial or telephone cable (depending on your modem type) ❖ Standard LAN cables ❖ Wireless LAN access point or wireless router ❖...
Page 49: Connecting The Ac Cord On Your Tv (For 84L9300U Series)
Connecting Your TV Connecting the AC cord on your TV (for 84L9300 Series) of certain Wi-Fi equipment that are based on the draft version of IEEE 802.11n. Connecting the AC cord on your TV (for 84L9300U Series) Place the ferrite core attachment around the AC cord near the connection end.
Page 50: Chapter 3: Using The Remote Control
Chapter 3 Using the Remote Control Controlling other devices The TV’s remote control can operate other devices as described in “Setting the IR Blaster” on page Installing batteries To install batteries: Slide back and pull up to open the cover. (Sample Illustration) Removing the battery cover...
Page 51 Using the Remote Control Installing batteries Install two AAA size batteries. NOTE Use carbon zinc batteries or alkaline batteries. (Sample Illustration) installing the batteries Slide on the cover. Do not expose batteries to excessive heat such as sunshine, fire, etc. NOTE Dispose of batteries in a designated disposal area.
Page 52: Remote Control Effective Range
Using the Remote Control Remote control effective range Remote control effective range For optimum performance, aim the remote control directly at the TV and make sure there are no obstructions between the remote control and the TV. 58” 65” 16.4 ft (5m) 16.4 ft (5m) 84”...
Page 53: Learning About The Remote Control
Using the Remote Control Learning about the remote control Learning about the remote control Only the buttons used to operate the TV are described in this section. ™ For the HDMI CEC Control functions, see “Using HDMI™ CEC Control” on page (Sample Illustration) Remote control overview...
Page 54 Using the Remote Control Learning about the remote control NOTE The error message “Not Available” may appear if you press a button for a function that is not available. Item: Description: Function: Item: Description: Function: POWER button Turns the TV On and Off. When QUICK button Launches the Quick menu.
Page 55: Chapter 4: Nitial Setup And Menu
Chapter 4 Initial Setup and Menu Initial setup When you first turn on or reset the TV, the Menu Language screen appears. NOTE You can stop initial setup by pressing the EXIT button. However, if you do not finish Channel Tuning setting, the Quick Setup screen will appear every time you turn on your TV.
Page 56: Performing The Initial Setup
The finished items are dark, and the finish mark ( ) appears by them. The setup window shows the settings. Progress window Setup window Quick Setup Country Welcome Country Thank you for choosing Toshiba TV Time Zone Store/Home Mode U.S. Network Canada Smart TV Mexico Channel Tuning IR Blaster...
Page 57 Initial Setup and Menu Performing the initial setup Basic Operations in Quick Setup Use the the p / q (arrow) buttons to select an item on the setup window, and press the OK button. Select Next and press the OK button. The next item will appear.
Page 58 Initial Setup and Menu Performing the initial setup Performing the Quick Setup Country Select a country then press the OK button. Time Zone Select Time Zone, and select a time zone from the submenu. Select Daylight Saving Time, and select On or Off from the submenu.
Page 59: Smart Tv
Initial Setup and Menu Performing the initial setup NOTE Easy Setup. If your Access Point (AP) supports WPS, this method can be used. WPS is a standard designed to simplify the connection of wireless LAN equipment and the setup of network security features. Assisted Setup (setup using the AP's notification information).
Page 60: Channel Tuning
Initial Setup and Menu Performing the initial setup Select Media Renderer, and select On or Off from the sub menu. When On is selected, the Media Renderer function can be used. Select Next. Channel Tuning Select Antenna or Cable, and select Start Scan. Auto Tuning will start.
Page 61: Ir Blaster
Initial Setup and Menu Performing the initial setup If some channels are not found after scanning: Check the antenna/cable connections, and scan again. Connect the TV to the antenna or cable box directly and scan again. Press the SETUP button. Select Installation > Quick Setup and press the OK button.
Page 62 Initial Setup and Menu Performing the initial setup CD Player Video Accessory Press the q button then press the GREEN button. The Brand screen will appear. Use the p / q (arrow) buttons to select the brand name then press the OK button. Select a field and press the OK button to show the software keyboard.
Page 63 Initial Setup and Menu Performing the initial setup Press the OK button. Input & Mode Key screen will appear. Input & Mode Key Use the t / u (arrow) buttons to select the TV input to which the IR device is connected. --- (Appears when Device Type is set to Receiver, Misc Audio or Amplifier) ANT/CABLE...
Page 64: Support Information
Initial Setup and Menu Performing the initial setup Volume Control Use the t / u (arrow) buttons to set up the Volume control to select: TV (this is the default) External The Volume + or – and MUTE buttons will control the External equipment through the IR blaster.
Page 65: Navigating The Menu System
Initial Setup and Menu Navigating the menu system Navigating the menu system To open the menu system, press the SETUP button on the remote control. < Picture Picture Picture Mode Standard Reset Sound Backlight Options Contrast Brightness Installation Color Tint Network Sharpness Advanced Picture Settings...
Page 66: Quick Menu
Initial Setup and Menu Quick Menu Quick Menu Quick menu helps you access some options more quickly. Press the QUICK button to display the Quick menu and press the p / q (arrow) buttons to select an option. NOTE Quick menu items differ depending on the current mode. Quick Menu Item Page ®...
Page 67: Chapter 5: Setting Up Your Tv
Chapter 5 Setting up your TV How to navigate the menu Press the SETUP button. Select Installation, Main menu, ❖ Submenu, and then press the OK or EXIT button. Changing initial settings From Quick Setup: Press the SETUP button. Select Installation > Quick Setup, and press the OK button. A confirmation message appears.
Page 68: Time Zone
Setting up your TV Individual settings Country You can select the country in which you reside. Press the SETUP button. Select Installation > Country and press the OK button. Press the p / q (arrow) buttons to select the country. Press the OK button.
Page 69: Storing Channels In Memory (Optional)
Setting up your TV Storing channels in memory (optional) Press the p / q (arrow) buttons to select Antenna or Cable. Press the OK button. Select Start Scan. After scanning is complete, the auto tuning results screen will appear. Press the OK or EXIT button. Storing channels in memory (optional) To make sure your TV stops only on the channels you want when you press the CH p / q buttons on the remote control or the control panel, store...
Page 70: Skipping Channels
Setting up your TV Skipping channels Manual Tuning After storing channels in memory, you can manually enter channels if the channel number is known. Press the SETUP button. Select Installation > Channel Tuning > Manual Tuning, and then press the OK button. Use buttons 0–9 on the remote control to enter the channel number (for example, 56).
Page 71: Skipping Video Inputs
Setting up your TV Skipping video inputs NOTE You cannot tune skipped channels using the CH buttons. Use buttons 0–9 and the DASH button on the remote control. Skipping video inputs You can set video inputs to be skipped when selecting inputs in the Input selection screen.
Page 72: Labeling Video Inputs
Setting up your TV Labeling video inputs Labeling video inputs The input labels are shown in the input selector and banner displays. You can label video inputs according to the devices you have connected to the Press the SETUP button. Select Options >...
Page 73: Chapter 6: Basic Features
3D capable HDMI cable. ❖ If you wish to obtain extra 3D glasses: Toshiba provides 3D glasses for this television as an option. To obtain them visit: US: http://ceaccessories.toshiba.com/ NOTE Use the type of 3D glasses that are compatible with to your TV.
Page 74: Basic Features
Basic features Using 3D functions Health precautions: Due to the possible impact on vision development, viewers of 3D ❖ programming should be age 6 or above. Children may be more susceptible to health effects from viewing 3D images and should be closely supervised.
Page 75: Viewing 3D Images
Basic features Using 3D functions NOTE Watching the TV: Proper 3D effects or 3D-to-2D conversion results may not be obtained ❖ depending on the received 3D content. 3D effect and image quality may vary depending upon content quality ❖ and display device capability/ functionality/settings. Wear the 3D glasses properly, otherwise you may not see the correct ❖...
Page 76: Switching Display Mode Or Selecting 3D Format
Basic features Using 3D functions When viewing 3D images, wear the 3D glasses. ❖ The 2D to 3D conversion function is activated and controlled by you ❖ according to your personal preferences. The 2D to 3D conversion function is meant for enjoyment of 2D home ❖...
Page 77: The 3D Button Operation
Basic features Using 3D functions The 3D button operation Depending on the input mode, the 3D button function may be different when viewing Native mode. Input: Function: Analog Broadcast Changes the viewing mode to 2D to 3D mode. Digital Broadcast Displays the selection window.
Page 78: Switching To 3D Mode
Basic features Using 3D functions Switching to 3D mode Set 3D Auto Start to 3D. ❖ Press the 3D button and select 3D while viewing 2D mode or Native ❖ mode. Input Signal/Switching Display Mode Trigger Press 3D Button Type Additional Information Format Source Select 3D...
Page 79: Switching To 2D Mode
Basic features Using 3D functions Input Signal/Switching Display Mode Trigger Quick menu/ 3D Format Select Type Additional Format Source Information Signal With 3D Auto Detect Information 3D Format Signal Without 3D Auto Detect Information 2D Format Signal * Correct 3D image. Switching to 2D mode Set 3D Auto Start to 2D.
Page 80: Switching To Native Mode
Basic features Using 3D functions Selecting 2D format from the Quick menu in 2D mode Press the QUICK button. Select 3D Settings > 2D Format Select. Press the OK button. Press the t / u (arrow) buttons to select Side by Side or Top and Bottom.
Page 81: Setting The 3D Pin Code
Basic features Using 3D functions Quick menu in 2D mode Press the QUICK button. Select 3D Settings > 2D Format Select and press the OK button. Press t / u (arrow) buttons to select Native. To switch 2D to 3D mode Press the 3D button and select 2D to 3D while viewing 2D or Native ❖...
Page 82: Forgotten Pin Codes
Basic features Using 3D functions Change or delete your PIN code Press the SETUP button. Select 3D > 3D PIN. Press the OK button. Press the number buttons to enter your 4-digit PIN code. Select Change PIN or Delete PIN, and then press the OK button. NOTE The PIN code cannot be set to “0000.”...
Page 83 Basic features Using 3D functions Enter your 4-digit 3D PIN code. Press the p / q (arrow) buttons to select 3D Lock and press the OK button. Press the p / q (arrow) buttons to select On. Setting the 3D Timer Lock When the 3D Timer Lock feature is set to On, the PIN input window and the 3D start message will not appear while the 3D Enable timer is active, even if you switch to 3D Mode.
Page 84: Displaying 3D Important Information
Basic features Using 3D functions Displaying 3D Important Information Press the SETUP button. Select 3D > 3D Important Info. Read through the information. Press the t / u (arrow) buttons to select Yes or No and press the OK button. Adjusting 2D to 3D depth With this feature, you can adjust the level of 3D depth.
Page 85: Tuning Channels
Basic features Tuning Channels Tuning Channels Tuning to the next programmed channel Press the CH p / q buttons on the remote control or TV control panel. Tuning to a specific channel (programmed or unprogrammed) Channel: Description: Analog Use the 0–9 buttons on the remote control. (For example, to select channel 125, press 1, 2, 5.), and then press the OK button.
Page 86: Using Closed Captions
Basic features Using closed captions NOTE You can label the video input sources according to the specific devices ❖ you have connected to the TV, see “Labeling video inputs” on page You can skip sources, see “Skipping video inputs” on page ❖...
Page 87: Analog Cc Mode
Basic features Using closed captions Analog CC mode The closed caption mode has two options: Mode: Description: Captions Displays the dialogue, narration, and sound effects of TV programs and videos that are closed captioned (usually marked “CC” in program guides). Text Displays information not related to the current program, such as weather or stock data (when provided by individual stations).
Page 88: Digital Cc Settings
Basic features Using closed captions NOTE If text is not available in your area, a black rectangle may appear on the screen. You can remove this rectangle by setting Closed Captions Display to Off. NOTE A closed caption signal may not be displayed when a videotape is dubbed, signal reception is weak, or signal reception is non-standard.
Page 89: Setting The Pin Code
Basic features Using closed captions Using the Closed Caption button If you press the CC button when an analog channel is tuned or from an external input (480i signal from the video input): The CC bar will appear and will display the options, CC1-4, T1-4. ❖...
Page 90: Forgotten Pin Code
Basic features Using parental controls Forgotten PIN code Press the SETUP button. Select Options > Parental PIN Setup. Press the OK button. Press the INFO button 4 times quickly. Select Change PIN and press the OK button. Enter a new PIN code. Using parental controls Blocking TV programs and movies by rating (V-Chip) Some TV programs and movies include signals that classify the content...
Page 91: Downloading An Additional Rating System
The additional rating system is not designed, transmitted, or controlled ❖ by the TV or Toshiba, nor is the availability of an additional rating system determined or controlled by Toshiba. Similarly, the rating of programs in an additional rating system is not...
Page 92: Rating System
Basic features Using parental controls The additional rating system is an evolving technology; therefore, ❖ availability, content, and format may vary. Rating system Independent rating system for broadcasters: Ratings: Description and Content themes: TV-MA Mature Audience Only (This program is specifically designed to be viewed by adults and therefore may be unsuitable for children under 17.
Page 93: Displaying Ratings
Basic features Locking specific channels NOTE If you place an “X” in the box next to “Rated “None””, programs rated “None” or “Not Rated” will be blocked; Programs that do not provide any rating information will not be blocked. Displaying ratings To display the rating of the program you are watching, press the INFO button on the remote control.
Page 94: Locking Video Inputs
Basic features Locking specific channels Locking video inputs You can lock video inputs. You cannot view the input sources until you unlock the inputs by entering the PIN code. Press the SETUP button. Select Options > Parental Control and Locks. Press the OK button. Enter your 4-digit PIN code.
Page 95: Using Hdmi ™ Cec Control
To unlock the control panel: Select Off in Step 3 above. ❖ ™ Using HDMI CEC Control This feature uses CEC technology and allows you to control Toshiba ™ ™ HDMI CEC compatible devices from the TV remote control via HDMI connection.
Page 96: Controlling Hdmi ™ Cec Playback Devices
Basic features ™ Using HDMI CEC Control NOTE These functions depend on the connected devices. ™ Controlling HDMI CEC playback devices ™ With your TV’s remote control, you can control the connected HDMI CEC playback device (DVD player, etc.) you are watching. Button: Description: Begins playback...
Page 97: Hdmi ™ Cec Control Input Source Selection
Basic features ™ Using HDMI CEC Control NOTE These functions depend on the connected devices. ™ The HDMI CEC Device Control item is not available under the following conditions: ™ A non-HDMI input is selected ❖ The Enable HDMI CEC Control item is set to Off ❖...
Page 98: Other Hdmi ™ Cec Control Functions
Basic features ™ Viewing the HDMI signal information ™ Other HDMI CEC Control functions ™ When Enable HDMI CEC Control and all items in the HDMI Control Setup menu are set to On, the following functions will be enabled: Item: Description: ™...
Page 99: Using Your Computer With The Tv
Basic features Using your computer with the TV Using your computer with the TV Adjusting the image If the edges of the picture are hidden, readjust Horizontal Position and Vertical Position. If the picture is affected by interference, readjust Clock Phase and Sampling Clock.
Page 100: Setting The Computer Audio
Basic features Setting the timer to turn on the TV Setting the computer audio You can output sound from your computer when connecting it to your TV, using the AUDIO IN terminal and PC audio cable. Press the SETUP button. Select Options >...
Page 101: Setting The Sleep Timer
Basic features Setting the sleep timer Item: Description: Input Video input source Channel Channel to view Volume Volume level Time until Power On Desired length of time until the TV turns on: minimum=00:10, maximum=12:00 Press the t / u (arrow) buttons Use the number buttons Select Done, and then press the OK button.
Page 102: Setting No Signal Power Down
Basic features Setting No Signal Power Down NOTE If a power failure occurs, the sleep timer setting may be cleared. To display the time remaining until the TV turns off, press the SLEEP button. To cancel the sleep timer, press the SLEEP button repeatedly or press the p / q (arrow) buttons until it is set to 0 minutes.
Page 103: Setting Tv Power On Control
Basic features Setting TV Power On Control Setting TV Power On Control When the TV is connected to the home network via Wireless LAN with the TV Power On Control in Enabled, your TV can be turned on by control from Apps. Press the SETUP button.
Page 104: Displaying Tv Status Information
Basic features Displaying TV status information Displaying TV status information To display TV status information, press INFO. The following information will be displayed (if applicable): Current input (ANT/CABLE, Video, etc.) ❖ Either “CABLE” (for cable TV) or “ANT” (for over-the-air ❖...
Page 105: Resetting To Factory Defaults
Basic features Resetting to Factory Defaults Resetting to Factory Defaults You can reset all settings and channels to Factory Defaults. Press the SETUP button. Select Installation > Reset TV. Enter your PIN code (if a PIN code has been set). A confirmation screen appears.
Page 106: Chapter 7: Picture And Sound Controls
Chapter 7 Picture and Sound Controls Selecting the picture size You can view many program formats in several picture sizes— Native, 4:3, Full, TheaterWide 1, TheaterWide 2, TheaterWide 3, Normal, Quad FHD, 4K Native, 4K Normal, and 4K Full. NOTE The picture size illustrations are examples only.
Page 107 Picture and Sound Controls Selecting the picture size You can save separate picture size preferences for each input on your TV. To select the picture size using the Quick menu: Press the QUICK button to open the Quick menu. Select Picture Size, and then press the OK button. Press the p / q (arrow) buttons to select the Picture Size, and then press the OK button.
Page 108 Picture and Sound Controls Selecting the picture size (Sample Illustration) Picture size - 4:3 Some program formats will display with sidebars and/or bars at the top and bottom. Full This setting is for viewing in the 16:9 (480i, 480p) source programs only. (Sample Illustration) Picture size - Full 16:9 If receiving a squeezed 4:3 format program, the picture is stretched horizontally to fill the width of the screen but not stretched vertically.
Page 109 Picture and Sound Controls Selecting the picture size TheaterWide2 This setting is for viewing letter box programs. A B C D E F G - - - - - - - - - - - - - - - - (Sample Illustration) Picture size - TheaterWide2, letter box The picture’s top and bottom edges may be hidden*.
Page 110 Picture and Sound Controls Selecting the picture size format, the picture appears with sidebars and/or bars at the top and bottom, for example, SVGA input source. * To view the hidden areas (such as subtitles or captions), see “Scrolling the picture” on page 111.
Page 111: Scrolling The Picture
Picture and Sound Controls Scrolling the picture Scrolling the picture If the edges of the picture are hidden, you can adjust the image’s position. NOTE You can adjust the picture position when the picture size is set to TheaterWide2 or TheaterWide3. When viewing Cloud TV, MediaShare or Internet content this feature is not available.
Page 112: Adjusting The Picture
Picture and Sound Controls Using the 4:3 Stretch Select Picture > Display Settings > 4:3 Stretch and press the OK button. Press the p / q (arrow) buttons to select On. Press the EXIT button. Adjusting the picture Selecting the picture mode You can select your desired picture settings from the modes described below.
Page 113: Adjusting The Picture Quality
Picture and Sound Controls Adjusting the picture Adjusting the picture quality The adjustments you make to picture quality under a picture mode are saved to that picture mode. Selection Press ( t ) Press ( u ) Backlight* Darker Lighter Contrast Lower Higher...
Page 114: Using The Advanced Picture Settings Features
Picture and Sound Controls Using the advanced picture settings features Using the advanced picture settings features NOTE Some of the Advanced Picture Settings features will not be available for adjustment when the picture mode is set to AutoView. Resolution+ If the Resolution+ set to On (this is the default), the clarity levels can be adjusted automatically.
Page 115: Clearscan
Picture and Sound Controls Using the advanced picture settings features press the OK button. Press the p / q (arrow) buttons to select On or Off. Press the EXIT button. ® ClearScan ® ClearScan 240Hz uses both frame interpolation technology and advanced backlight control with image synchronization to quadruple the TV refresh rate for an even clearer fast motion video.
Page 116: Ambient Light Sensor
Picture and Sound Controls Using the advanced picture settings features and press the OK button. Press the p / q (arrow) buttons to select DNR and press the OK button. Press the p / q (arrow) buttons to select Low, Middle, High, Auto, or Off.
Page 117: Base Color Adjustment
Picture and Sound Controls Using the advanced picture settings features Base Color Adjustment When ColorMaster™ is set to On, the list of base colors appears. You can select a base color to adjust. Press the SETUP button. Select Picture > Advanced Picture Settings > Base Color Adjustment.
Page 118: Fine Texture Restoration
Picture and Sound Controls Using the advanced picture settings features Fine Texture Restoration This feature allows you to adjust fine texture of the picture. Press the SETUP button. Select Picture > Advanced Picture Settings > Fine Texture Restoration. Press the OK button. Fine Texture Restoration screen appears. Press the p / q (arrow) buttons to select Auto or the picture texture level (1 to 10).
Page 119: Resetting To The Factory Default
Picture and Sound Controls Using the advanced picture settings features Resetting to the factory default Press the SETUP button. Select Picture > Advanced Picture Settings > Reset. Press the OK button. A confirmation screen appears. Select Yes, and then press the OK button.
Page 120: Setting The Expert Picture Settings
Picture and Sound Controls Setting the expert picture settings Setting the expert picture settings NOTE This feature is only available in Standard and Movie mode. Test Pattern When the test pattern is on screen, you can navigate the Picture submenus without removing the image.
Page 121: White Balance
Picture and Sound Controls Setting the expert picture settings White Balance Window Display This feature displays the Window Pattern to adjust the white balance. Press the SETUP button. Select Picture > Expert Picture Settings > White Balance and press the OK button. Press the p / q (arrow) buttons to select Window Display and press the OK button.
Page 122: Adjusting The Audio
Picture and Sound Controls Adjusting the audio Adjusting the audio Muting the sound Press the MUTE button to partially reduce (1/2 Mute) or turn off (Mute) the sound. Each time you press the MUTE button, the mute mode changes in the following order: 1/2 Mute, Mute, Volume, 1/2 Mute, etc. NOTE If you modify items in the Sound menu while Mute is active, Mute is cancelled.
Page 123: Tv Speakers On/Off
Picture and Sound Controls Adjusting the audio Press the OK button. Press the t / u (arrow) buttons to adjust the range. Press the EXIT button. TV Speakers On/Off This feature allows you to turn the TV speakers off when connecting the audio system.
Page 124: Using The Dolby ® Digital Dynamic Range Control Feature
Picture and Sound Controls Adjusting the audio Press the p / q (arrow) buttons to select Auto or Manual. Auto: This mode automatically adjusts the audio timing to meet the video timing. The time lag might be large between the image and sound depending on the connected equipment (amplifier etc.).
Page 125: Audyssey Premium Television
Picture and Sound Controls Adjusting the audio NOTE ® ® This feature is available when Dolby Digital or Dolby Digital Plus is input to the TV in the following situations: When tuned to a digital RF channel ™ When an HDMI input is used This feature is automatically set to Off when Dynamic Volume (Audyssey ®...
Page 126: Using Audyssey Dynamic Volume
Picture and Sound Controls Adjusting the audio ® Using Audyssey Dynamic Volume This feature provides a consistent sound volume between television programs, commercials, and between the loud and soft passages of movies. Press the SETUP button. Select Sound > Audyssey Premium Television > Dynamic Volume and press the OK button.
Page 127: Chapter 8: Advanced Features
If you use Internet services, see the following note before use. NOTE Third party Internet services are not provided by Toshiba, may change or be discontinued at any time, and may be subject to third party restrictions. Toshiba makes no warranties, representations, or assurances about the content, availability, or functionality of third party content or services.
Page 128: When Using A Wireless Network Connection
Because Wireless LAN products operate within the guidelines found in radio frequency safety standards and recommendations, Toshiba believes Wireless LAN is safe for use by consumers. These standards and recommendations reflect the consensus of the scientific community and result from deliberations of panels and committees of scientists who continually review and interpret the extensive research literature.
Page 129: Setting Up The Network
LAN is not securely protected. Unauthorized users may access your data and network without appropriate security measures. Selecting an encryption setting from your Toshiba TV and using a secure network for wireless LAN transmissions may help avoid unauthorized access to your important data and/or TV. Toshiba disclaims any and all responsibility or liability resulting from any wireless transmissions over the Internet through your Toshiba TV.
Page 130 Advanced features Setting up the Network Easy Setup using PBC (Push button configuration) Press the SETUP button. Select Network > Network Setup > Wireless Setup and press the OK button Press the p / q (arrow) buttons to select Easy Setup and press the OK button.
Page 131 Advanced features Setting up the Network To cancel searching for the AP: Press the BACK button while searching for the AP. A message ❖ appears. Press the t / u (arrow) buttons to select Yes, and then press the OK button. Assisted Setup Press the SETUP button.
Page 132 Advanced features Setting up the Network Press the p / q (arrow) buttons to select Network Name, and then press the OK button. The Software Keyboard window appears. Input the Network Name using the Software Keyboard. For more information, see “Using the software keyboard”...
Page 133 Advanced features Setting up the Network NOTE Settings are not saved if the BACK button is pressed before Done is selected. Wireless Information The settings configured in Wireless Setup can be confirmed. Press the QUICK button. Select Wireless Information, and then press the OK button. Press the RED button to check the availability of surrounding APs.
Page 134: Advanced Network Setup
Advanced features Setting up the Network Advanced Network Setup NOTE When manually setting the IP Address, set Auto Setup to Off. IP Address Setup NOTE The settings in Auto Setup are linked to those selected in the DNS Setup menu. If Auto Setup is set to On, then Auto Setup in the DNS Setup menu will also be set to On.
Page 135: Dns Setup
Advanced features Setting up the Network NOTE IP address field numbers must be between 0 and 255. If you input an incompatible number and press the OK button, the field number will be reset to the previous value. Press the p / q (arrow) buttons to highlight Subnet Mask, and edit in the same way as IP Address.
Page 136: Network Connection Test
Advanced features Setting up the Network Press the p / q (arrow) buttons to select DNS Setup, and then press the OK button. Press the p / q (arrow) buttons to select Auto Setup and press the OK button. Press the p / q (arrow) buttons to select Off. Press the p / q (arrow) buttons to select Primary DNS Address.
Page 137: Using The Software Keyboard
Advanced features Using the software keyboard Using the software keyboard You can enter text using the Software Keyboard. The Software Keyboard window will appear when you press the OK button on a field that accepts character input. NOTE When using the SmartTV features, software keyboard availability depends on the Internet service being accessed.
Page 138: Enter Text Using The Software Keyboard
Advanced features Using the software keyboard Enter text using the software keyboard Highlight the desired character on the on-screen software keyboard. Press the OK button. Repeat Step 1 and 2 until you have entered all desired text. Select Done or press the GREEN button to save your settings and return to the previous screen.
Page 139: Performing A Software Upgrade
Advanced features Performing a Software Upgrade Performing a Software Upgrade TOSHIBA may offer upgrades for the TV's software in the future. The TV's software is upgraded via the Network. NOTE An Internet connection is required. Before downloading software: Configure your TV to connect to the Internet.
Page 140: Using Intel ® Widi
“Connecting” will be shown on the TV. Connecting your PC to the TV the first time When selecting the Toshiba TV for the first time, a 4-digit or 8-digit code will appear on your TV screen. This code needs to be inputted into your computer to authenticate the connection.
Page 141: Changing The Intel ® Widi Device Name
List. When doing so the following text can be seen “Do you want to unregister this device? Yes/No” (default cursor is “No”). Using the Cloud Service Toshiba's universal portal for Internet content and services. (Services are dependent on country).
Page 142: Using The Cloud Tv Service Features
❖ User registration or login may be required to use some services. ❖ Third party Internet services are not provided by Toshiba, may change ❖ or be discontinued at any time and may be subject to Internet service provider restrictions. Toshiba makes no warranties, representations, or assurances about the content, availability or functionality of third- party content or services.
Page 143: Feature Apps
Advanced features Using the Cloud TV Service features Feature apps With easier content discovery, Cloud TV puts you closer than ever to ® ® the things you love— like Netflix and Hulu Plus , along with video on demand, broadcast programming, the Web, even music, photos and videos on your home network.
Page 144: Vudu Tm Hd Movies And Vudu Tm Apps
Advanced features Using the Cloud TV Service features Press the p / q (arrow) buttons to select Deactivation, and then press the OK button. Press the t / u (arrow) buttons to select Yes, and then press the OK button. VUDU HD Movies and VUDU Apps...
Page 145: Browsing Favorite Websites
Advanced features Using the Cloud TV Service features uses a single built-in font. Some text may not be displayed as ❖ intended. does not support downloading of files or fonts. ❖ is a TV browser. It may work differently than PC browsers. ❖...
Page 146 Advanced features Using the Cloud TV Service features Select the item or folders to move to the desired URL address and press the OK button. NOTE You can press the GREEN button on the remote for thumbnail view of all your favorites.
Page 147: Using Skype
Before using Skype™ - Preparation Connect the FREETALK HD Camera: TALK-7291 to the TV’s ❖ USB port. Do not use a USB hub. For a Skype™-ready Toshiba TV compatible camera, please visit the following website: http://shop. skype.com Arrange the HD camera on top of the TV, ensuring it's in the center.
Page 148: Getting Started
Advanced features Using the Cloud TV Service features The sound settings are switched to Skype™ mode. ❖ If you cannot hear the person you're speaking with, check your TV ❖ volume. When Optical Digital output or Analog output is used and you are ❖...
Page 149 Advanced features Using the Cloud TV Service features Welcome to Skype Skype Name Press [OK] Password Press [OK] Sign in when Skype starts Start Skype when TV starts Sign in Create Account (Sample Image) Welcome Skype screen Select Sign in or Create Account. To create a new account: If you do not already have a Skype™...
Page 150 Advanced features Using the Cloud TV Service features NOTE Please ensure that you have entered your email address correctly. It is ❖ required in case you lose or forget your password. If you forget your password, visit skype.com to retrieve it. ❖...
Page 151 Advanced features Using the Cloud TV Service features Contacts/People Press the p / q (arrow) buttons to select Contacts tab. Press the c / p / q (arrow) buttons to select a contact. After pressing the OK button on each contact, the following functions will be displayed: No blocked contactor Initiate Video Call...
Page 152: Incoming Call
Open dial pad End call ( Hang up the call ) Group calls Using your Toshiba TV, you can join Skype™ group voice and video calls. However, you can only send and receive audio while on these calls. NOTE You must be invited on to a group call, you cannot initiate it from the TV.
Page 153 Advanced features Using the Cloud TV Service features Status When pressing the GREEN button, the change status window is displayed as below. You can change your status by pressing the p / q (arrow) buttons and then pressing the OK button. Exit by pressing the BACK button.
Page 154 Advanced features Using the Cloud TV Service features Contact Search Results Add a Skype contact Search Result: (jackyding) Full Name Skype Name Country Aaaaaa_0101 Aaaaaa_0101 Bbbbbb007 Bbbbbb007 Cccccc0709 Cccccc A01 Ddddddd Ddddddd Ddd Eeeeee_Eeee EE_Eeeee Japan Ffffffffff_Fu Ffffffffff_Ff Gggggg_Ggg Gggggg_Ggg Japan Back (Sample Image) Skype...
Page 155 Advanced features Using the Cloud TV Service features ms_audi Hello! Please add me to your Contacts. Accept Block Decline (Sample Image) Skype request form screen Recent You can see a list of past events in “Recent”. Press the p / q (arrow) buttons to select the Recent tab. Press the c / p / q (arrow) buttons to select an item and press the OK button.
Page 156: Change Password
Advanced features Using the Cloud TV Service features Name - TextTextTextTextTextTextTextTextTextTextTextText Skype Credit Dialer Please input the country code -Select One- Taiwan +886 Tajikistan +992 Tanzania +255 Thailand Timor-Leste +670 Togo +228 Status Add Contact Exit (Sample Image) Skype dialer screen Select the country or region first, and then enter the phone number with area code.
Page 157: Mediashare (Videos, Music, And Photos)
Advanced features Using the Cloud TV Service features The volume of your speakers will be different on Skype™ compared to your normal TV volume level. The speaker volume range is 0 - 100% by 1 steps, and ringtone volume is 0 - 100% by 25 steps. Privacy Settings ❖...
Page 158: Basic Operation
FAT16, FAT32 and exFAT (SDXC memory card) ❖ NOTE You must obtain any required permission from copyright owners to download or use copyrighted content. Toshiba cannot and does not grant such permission. Basic operation Using MediaShare with a USB device or SD card When Auto Start is enabled, you will be asked if you want to start the MediaShare whenever a USB device or SD card is inserted.
Page 159: Manual Start
Advanced features Using the Cloud TV Service features NOTE If Auto Start is set to Off, you can start the MediaShare (Media Player) manually. Manual Start Insert a USB device into the USB port, or insert an SD card into the SD card slot.
Page 160 Advanced features Using the Cloud TV Service features Using MediaShare with a Media Server You need to configure a home network before using this feature, see “Setting up the Network” on page 129. Press the MEDIA SHARE button. To change the device press the p / q / t / u (arrow) buttons to select the Device Name button on the screen, and then press the OK button.
Page 161: Viewing Movie Files
Advanced features Using the Cloud TV Service features Viewing movie files Basic Playback Select a file, see “To select a file in the list of contents” on page 159. Press the OK button or PLAY button to begin playback. NOTE Depending on the file size, it may take some time to start playback.
Page 162 Advanced features Using the Cloud TV Service features To locate a specific file Press the Skip Reverse or Skip Forward button repeatedly to ❖ access the desired file. ( Z ): Playback starts from the beginning of the current file or ❖...
Page 163 Advanced features Using the Cloud TV Service features The information will be displayed at the bottom of the screen. Press the INFO button again to hide the information. NOTE The information may not correctly display depending on the content or media server.
Page 164 Advanced features Using the Cloud TV Service features ® ABOUT DIVX VIDEO-ON-DEMAND: This DivX Certified device must be registered in order to play purchased DivX Video-on-Demand (VOD) movies. To obtain your registration code, locate the DivX VOD section in your device setup menu. Go to vod.divx.com for more information on how to complete your registration.
Page 165 Advanced features Using the Cloud TV Service features Using Multi Title and Alternative Timelines Multi Title ® DivX Plus HD files may contain up to 100 titles. You can change the title (It contains same video file) by pressing the RED button.
Page 166: Playing Music Files
Advanced features Using the Cloud TV Service features NOTE It may not be possible to use certain playback or display some files. In some cases certain files and servers may not support playback features, such as pause. Playing music files Basic Playback Select a file, see “To select a file in the list of contents”...
Page 167 Advanced features Using the Cloud TV Service features To set the repeat mode Press the QUICK button. Press the p / q (arrow) buttons to select the Repeat. The current repeat setting appears. Press the t / u (arrow) buttons to select Off, All, or 1. Press the BACK button.
Page 168: Viewing Photo Files
Advanced features Using the Cloud TV Service features File format: MP3, MP4 (AAC), WMA9 std, LPCM ❖ Sampling frequency: 32 kHz, 44.1 kHz, 48 kHz ❖ Bit rate: From 32 to 320 kbps ❖ Maximum number of files: 1000 per folder ❖...
Page 169 Advanced features Using the Cloud TV Service features NOTE Single view mode is changed to Multi View mode when the BACK button is pressed. Slide Show mode This view allows you to watch a slide show of the photos. In this mode, only files located in the selected directory appear.
Page 170 Advanced features Using the Cloud TV Service features Rotate the image While viewing the image in Single View mode or Slide Show mode, press the p / q (arrow) buttons to rotate the image 90 degrees. To select a photo from Play List (except for Media Renderer function) While in the Single View mode or Slide Show mode, you can select a different photo from the Play List.
Page 171: Search
Advanced features Using the Cloud TV Service features Search To search for content, Select the search. Enter in keyword and the search will search for: Media Server ❖ Videos; Title name Music; Title name/Artist name/ Album name Photos; Title name USB/SD card ❖...
Page 172: Network Device Setup
Advanced features Network Device Setup Network Device Setup In order to set the access the External Control Setup, Media Renderer Setup, or Device Name Setup, you must use the Network Device Setup menu. External Control Setup Press the SETUP button. Select Network >...
Page 173 Advanced features 4K Demonstration Press the p / q (arrow) buttons to select On or Off, and then press the OK button. Device Name setup The device name as a Media Renderer can be changed. Press the SETUP button. Select Network > Network Device Setup > Device Name Setup and press the OK button.
Page 174: Chapter 9: Cloud Tv Companion Apps
Chapter 9 Cloud TV Companion Apps Using Apps on a Tablet or Smart phone Toshiba provides apps for tablets and smart phones. The apps will vary by country and availability may change in the future with respect to current apps. NOTE Apps will vary by country and availability may change in the future on current apps.
Page 175: Apps Control Profile
Apps Collaboration Apps Control Profile Apps can only be used when your TV and your tablet or smart phone are connected to the Internet. Some app features may require the TV and smart phone/tablet to be on the same home network connection. Starting and operation of this service may take several minutes.
Page 176: Pairing
Apps Collaboration Pairing To enable the New Device Detection: Press the SETUP button. Select Network > Network Device Setup > External Control Setup and press the OK button. Press the p / q (arrow) buttons to select and set Apps Control Profile and press the OK button.
Page 177: Chapter 10: Troubleshooting
General troubleshooting Before calling a service technician, review this chapter or visit the Toshiba Technical Support Website at "support.toshiba.com" for possible causes/solutions for the problem you are experiencing. Before you begin to troubleshoot any problem, first unplug the TV from the AC wall outlet, wait approximately one minute, and then plug the TV back into the AC wall outlet.
Page 178: Picture Problems
Troubleshooting Picture problems Other problems. If your TV’s problem is not addressed in this Troubleshooting chapter or the recommended solution has not worked, use the Reset Factory Defaults procedure, see “Resetting to Factory Defaults” on page 105. TV will not turn on. Check the AC wall outlet by trying another device in the AC wall outlet.
Page 179 Troubleshooting Picture problems If Resolution+ does not achieve a sharper picture, change the Sharpness value to increase the sharpness level, see “Resolution+” on page 114. Video Input Selection problems. If the Input Selection window does not appear when you press INPUT on the remote control or the TV control panel, press INPUT a second time.
Page 180: Sound Problems
Troubleshooting Sound problems Sound problems Check the antenna/cable connections, see “Connecting a digital audio system” on page The station may be having broadcast difficulties. Try another channel. The sound may be muted. Press the VOL (+ -) buttons or MUTE button. If you are connected to a computer using either the PC IN terminal or ™...
Page 181: Closed Caption Problems
The V-Chip feature is available for U.S. V-Chip systems only, see “Using parental controls” on page ™ HDMI CEC Control operation ™ HDMI CEC Control feature is available for Toshiba HDMI™ CEC compatible devices. ™ HDMI cables. ™ Ensure that HDMI cables with the ( ) Logo are used.
Page 182: Hdmi ™ Problems
Troubleshooting ™ HDMI problems ™ HDMI problems ™ HDMI cables. ™ Ensure that HDMI cables with the ( ) Logo are used, see ® “Connecting an HDMI™ or DVI device to the HDMI™ input” on page Network problems Cannot connect to the Internet. Check the modem and its incoming cable/telephone connections, see “Connecting to a home network”...
Page 183 Troubleshooting Network problems Make sure the TV IP address is on the same subnet as the networked computer. Example of proper setup: The computer has the IP address ❖ 192.168.0.100 with the Subnet mask 255.255.255.0, the TV has the IP address 192.168.0.101 with the Subnet mask 255.255.255.0; both are on the same subnet.
Page 184: Wireless Network Problems
Troubleshooting Wireless network problems Wireless network problems Check that the router/AP (Access point) power is On. After starting wireless network setup, confirm that the network is configured properly by performing the network connection test, see “Network Connection Test” on page 136.
Page 185: Cloud Tv
Power On/Standby light Green: The TV is On and operating properly. ❖ Red: The power is Off or in Standby. ❖ If the problem persists after trying the solutions In the U.S., visit Toshiba Customer Support Center on the web at "support.toshiba.com".
Page 186: Appendix A: Specifications
Appendix A Specifications NOTE This model complies with the specifications listed below. Designs and specifications are subject to change without notice. This model may not be compatible with features and/or specifications that may be added in the future. Television system NTSC standard ATSC standard 8VSB...
Page 187: Power Consumption
Specifications Power consumption Power consumption 58L9300U 2.1 A (maximum current) 0.2 W in Standby mode 65L9300U 3.2 A (maximum current) 0.2 W in Standby mode 84L9300U 5.3 A (maximum current) 0.2 W in Standby mode Audio power 58L9300U 10 W + 10 W...
Page 188: Digital Audio Output
Universal Serial Bus Specification, Revison 2.0. SD card SD, SDHC and SDXC memory card Dimensions with table stand Width 51.4” (1306 mm) 58L9300U Height 33.7” (857 mm) Depth 14.7” (374 mm) Width 57.6” (1463 mm) 65L9300U Height 37.0” (940 mm) Depth 14.7”...
Page 189: Weight (Mass) With Stand
Pedestal Stand Assembly instructions Warranty information Wireless QWERTY keyboard with touchpad (2x AA batteries) IR blaster cable Toshiba 3D glasses For 58L9300U: FPT-AG03 (1x CR2032 battery) x 2 For 65L9300U/84L9300U: FPT-P100 x 4 For 84L9300U: AC power cord Ferrite core attachment...
Page 190: Acceptable Signal Formats For Pc In, And Hdmi
Specifications ™ Acceptable signal formats for PC IN, and HDMI , and 3D ™ Acceptable signal formats for PC IN, and HDMI , and 3D PC IN signal formats NOTE The PC IN on this TV only accepts signal formats which are compliant with VESA-DMT as in the table below.
Page 191: Hdmi ™ Signal Formats
Specifications ™ Acceptable signal formats for PC IN, and HDMI , and 3D ™ HDMI signal formats NOTE ™ The HDMI inputs on this TV only accept VGA, SVGA, XGA, WXGA, and SXGA signal formats which are compliant with VESA-DMT as in ™...
Page 192: 3D Signal Formats
Certain HDMI formats or still images exceeding “4K” resolution may not be supported. May require purchase of additional external hardware, software and/or services. Toshiba makes no representation or warranties about any future “4K” content, standards or services.
Page 193: Operating The Tv With Combination Buttons
Specifications Operating the TV with combination buttons Operating the TV with combination buttons You can directly operate the TV power, input, picture size, and picture mode by pressing a combination button while holding down a color button. Button Color Combination Button Behavior/Mode INPUT Power Off...
Page 194: Appendix B: Wireless Qwerty Keyboard With Touchpad
Appendix B Wireless QWERTY keyboard with touchpad How to enter French or Spanish characters using the Wireless ❖ QWERTY keyboard with touchpad For how to use the Wireless QWERTY keyboard with touchpad, ❖ refer to the User's Guide that comes with the keyboard. Setting the keyboard layout Before entering French or Spanish characters, configure the following setting on the TV:...
Page 195 Printing Simultaneous Key normal Shift Right Alt(Alt Gr) Shift + Right Alt a and A a or A á or Á b and B b or B c and C c or C © ¢ d and D d or D Ð...
Page 196 Printing Simultaneous Key normal Shift Right Alt(Alt Gr) Shift + Right Alt ] and } » ” \backslash and | ¬ ; and : ¶ ° ‘ and “ ´ ¨ Grave Accent(`) and Tilde(~) , and < < ç or Ç .
Page 197: International Key Table
International Key table To enter special characters, follow the table below: Diacritic press first press second (Dead key) Space Acute ' or ´ É é Á á Ó ó Ú ú Ý ý Í í Ź ź Ŕ ŕ Grave È...
Page 198: Index
Index Numerics advanced picture settings 2D from Quick menu 80 3D Judder Cancellation 118 3D from Quick menu 78 Ambient Light Sensor 116 3D lock 82 Base Color Adjustment 116 ® 3D timer lock 83 ClearScan adjusting 2D to 3D depth 84 Color temperature 117 auto start mode 81 ColorMaster™...
Page 199 Index Auto Aspect connecting using 111 a computer 43 audio system 38 cable TV 32 cables camcorder 32 3.5mm to RCA Y-cable 31 computer to TV’s PC IN 43 analog RGB (15-pin) 31 ® DVD player with ColorStream coaxial (F-type) 29 component video (red/green/blue) ™...
Page 200 Index Factory Defaults network reset 105 advanced setup 134 favorites connection test 136 adding 146 DNS setup 135 browsing 145 quick setup 58 features 21 setup 129 wireless setup 129 Network Device Setup 171 ™ HDMI no signal power down viewing signal information 98 set 102 ™...
Page 201 TV 100 ® Netflix troubleshooting 177 VUDU™ 144 channel tuning problems 180 software keyboard closed caption problems 181 using 137 contact Toshiba 185 software licenses ™ HDMI show 139 ™ HDMI CEC Control problems software upgrade performing 139...
Page 202 Index MediaShare (Media Player) problems 184 network problems 182 picture problems 178 Rating blocking problems 181 remote control problems 180 sound problems 180 wireless network problems 184 TV connections front 24 side 24 TV panel connections back 25 TV panel controls front 24 left side 24 side 24...

This manual is also suitable for:

65l9300u 84l9300u

Toshiba 58L9300U User Manual

Chapter 1: Introduction

Chapter 2: Connecting Your TV

Chapter 3: Using the Remote Control

Chapter 4: Nitial Setup and Menu

Chapter 5: Setting up Your TV

Chapter 6: Basic Features

Chapter 7: Picture and Sound Controls

Chapter 8: Advanced Features

Chapter 9: Cloud TV Companion Apps

Chapter 10: Troubleshooting

Appendix A: Specifications

Appendix B: Wireless QWERTY Keyboard with Touchpad

Quick Links

Related Manuals for Toshiba 58L9300U

Summary of Contents for Toshiba 58L9300U