Important Safety Information You MUST read these warnings carefully before installing or using the hob. If you need assistance, contact our Customer Care Department on 01635 522799 Installation This hob must be installed by qualified personnel, Never use plastic or aluminium foil dishes on the according to the manufacturer’s instructions and hob.
Contents For the Installer For the User Technical Data Page 13 Description of the Hob Page 5 Important Safety Requirements Page 13 Operation Page 6 Installation Page 14 Maintenance and Cleaning Page 8 Building In Page 14 Something Not Electrical Connection Page 16 Working? Page 9 Wiring Diagram...
Description of the Hob EHE 682 1. Hob Top 2. Normal Hotplate - 1570 W/180 mm dia. EHE 684 3. Normal Hotplate - 1040 W/145 mm dia. EHE 685 4. Rapid Hotplate - 1570 W/145 mm dia. 5. Rapid Hotplate - 2090 W/180 mm dia.
Operation ELECTRIC HOTPLATES To switch on a hotplate, turn the relevant control knob anticlockwise to the required heat setting. The control knob is numbered 1 - 6 0 - OFF 1 - Minimum 2 - Maximum. The hob has two types of hotplates: Normal Hotplates We recommend the plates are switched to maximum (6) for a short while to boost the plate, and then...
Page 6
Hints and Tips Saucepans for use on solid plates should have several characteristics: They should be fairly heavy duty They should fit the heat area exactly, or be slightly larger for efficient use, NEVER smaller. They should have a flat base to ensure good contact with the plate.
Maintenance and Cleaning Before any maintenance or cleaning can be carried out, you must DISCONNECT the hob from the electricity supply. The hob is best cleaned whilst it is still warm, as spillage can be removed more easily than if it is left to cool.
Something Not Working? If the hob is not working correctly, please carry out the following checks before contacting your local Electrolux Service Force Centre. SYMPTOM SOLUTION The plate does not heat up. Check that the unit is plugged in and the electrical supply is switched on Check that the RCCB has not tripped (if fitted) Check the mains fuse has not blown...
Guarantee Conditions ELECTROLUX STANDARD GUARANTEE * Appliances found to be in use within a CONDITIONS commercial or similar environment, plus those which are the subject to rental agreements. We, Electrolux, undertake that if, within 12 months * Products of Electrolux manufacture which are not of the date of the purchase, this Electrolux appliance marketed by Electrolux.
ELECTROLUX SERVICE FORCE To contact your local Electrolux Service Force Centre telephone 0990 929929 NORTH EAST ISLE OF LEWIS ND Macleod CHANNEL ISLANDS (M69) 16 James Street Stornoway GUERNSEY Guernsey Electricity GATESHEAD Unit 356a Isle of Lewis PO Box 4 (M39) Dukesway Court PA872QW...
Page 11
ELECTROLUX SERVICE FORCE To contact your local Electrolux Service Force Centre telephone 0990 929929 MIDLANDS LONDON & EAST ANGLIA SOUTH EAST BIRMINGHAM 66 Birch Road East, CANVEY ISLAND 2-4 Sandhurst ASHFORD Unit 2 (M18) Wyrley Road Industrial Kings Road (M58) Bridge Road Business Estate Canvey Island...
Instructions for the Installer Engineer technical data Important safety requirements This hob must be installed in accordance with the IEE OVERALL DIMENSIONS Wiring Regulations (Current Edition). Width: 580 mm. Detailed recommendations are contained in the Depth: 500 mm. following British Standards Codes Of Practice: B.S. Height: 88 mm.
Installation Rectangular cut-out size for hob IMPORTANT This hob must be installed by qualified personnel to the relevant British Standards. The manufacturer will not accept liability, should the above instructions or any of the other safety instructions incorporated in this book be ignored. Cut Out Size The dimensions of the cut-out are given in the diagram.
Building over a kitchen unit with door Proper arrangements must be taken in designing the furniture unit, in order to avoid any contact with the bottom of the hob which can be hot when in operation. The recommended solution is shown in diagram 3.
Electrical connections The hob should be connected to a double pole switch Any electrical work required to install this with a minimum gap of 3 mm. between the switch hob should be carried out by a qualified electrician or competent person, in contacts and of a type suitable for the required load in accordance with the current regulations.