Related Manuals for D-Link DMC-920
Summary of Contents for D-Link DMC-920
- Page 1 DMC-920 10/100BASE-TX to 100BASE-FX Single-Fiber Dual-Wavelength Media Converter Kit User’s Guide Rev. 02 (DEC. 2004) Printed In Taiwan RECYCLABLE...
-
Page 2: Table Of Contents
TABLE O N T E N T S TABLE OF CONTENTS ..2 INTRODUCTION ....2 .... 3 AVELENGTH INGLE IBER PRODUCT FEATURES ..3 INSTALLATION ....4 ..4 ELECTING A ITE FOR THE QUIPMENT ......4 ONNECTING TO OWER .......... -
Page 3: Dual -Wavelength
Converter introduced here provides a pair of one channel single fiber media conversion between 10/100BASE-TX and 100BASE-FX Single Fiber. Dual-Wavelength Single-Fiber These types of Single-Fiber modules combine transmit and receive signals onto one fiber strand using two wavelengths. This design avoids the budget losses incurred by the single-wavelength single-fiber technology, and minimizes any possibility of reflections in the system. -
Page 4: Installation
NSTALLATION This chapter gives step-by-step installation instructions for the Converter. Selecting a Site for the Equipment As with any electric device, you should place the equipment where it will not be subjected to extreme temperatures, humidity, or electromagnetic interference. Specifically, the site you select should meet the following requirements: The ambient temperature should be between 32 and 104 degrees Fahrenheit (0 to 40 degrees Celsius). -
Page 5: Installing In A Chassis
port. Refer to the table below for more details. Full Duplex Half Duplex (default) Installing in a Chassis The Converter can be fit into any of the expansion slots on a special designed chassis. First, install the converter onto a carrier supplied with the chassis: Step 1- Unscrew and pull out the media converter board. -
Page 6: Led Indicator
LED Indicator The LED indicators give you instant feedback on status of the converter: LEDs State Indication Steady Power on Power (PWR) Power off Steady Runs at 100Mbps on TX port 100 Mbps (100) Runs at 10Mbps on TX port Steady Connection in full duplex mode (FDX) - Page 7 The Management Chassis will detect the default reset on the DIP switches and display out the status, also the Management Chassis can control the function through the management system. Through the optional Media Converter Chassis System via Management Module, you can control the setting of this Smart Media Converter.
-
Page 8: Function
Link Pass Through Function LLR (Link Loss Return) When a device connected to the converter and the fiber line loss the link, the converter’s fiber will disconnect the link of transmit. The switch 5 is to enable or disable the LLR function of the media converter. - Page 9 Link Status Link Link Link Link Link 1 Link 2 Link 3 Link 4 Link 5 Link 6 Link 7 Link 8 Fail 1 Fail 2 Fail 3 Fail 4 Disconnect Cable 1 Cable 2 Cable 3 Cable 4 Cable 5 Cable 6 Note: When using two converters, don’t enable the both device’s LLR function at the same time.
-
Page 10: Ingle Fiber
Link Link Link Link Link Status Link Link Link Link Link Link Fail 1 Fail 2 Fail 3 Fail 4 Disconnect Cable 1 Cable 2 Cable 3 Cable 4 Switc h A Fib e r Switc h B Fib e r LINK 6 LINK 5 T X RX... -
Page 11: Wavelength
When using a DMC-920R that the TX(transmit) is 1310µm and the RX(receive) is 1550µm, then the other end need to have a combination of DMC-920T that the TX(transmit) is 1310µm and the RX(receive) is 1550µm. The TX needs to connect to the other end’s RX with the same wavelength. -
Page 12: Specifications
PECIFICATIONS Applicable IEEE 802.3 10BASE-T Standards IEEE802.3u 100BASE-TX & 100BASE-FX Fixed Ports 1 TX port, 1 Single Fiber FX port Speed 10/20Mbps for half/full-duplex 100/200Mbps for half/full-duplex Forwarding 148,800pps rate Per Unit- (2 LEDs): Power; Speed( 100 ) Indicators Per Port- (2 LEDs): FDX/COL, LINK/ACT Cable 10BASE-T –...