Advertisement
Figure _2
4, Install eeppe,
three wire pc,wet
super,, * cabe
thraugh stran relief
Slide the hook end of the neutrai
(white o_ canto 0 wre from the
three-wit÷
power
suppy cable
undo
the center, silv®Pco ored
term no_ screw oF the formica! b:ock,
Squeeze the hook end oF the wire
together
Tighten screw,
6 Connect
the othe¢ wr_
1o the outer
terTenas
_s_ng the _me
method,
i"igt len screws firmly Gee Figure !2)
7. f_ghten _tain relef screws.
love&
Where
toeat codes
DO NOT permit
eo_necttng the cabinef._ounding
conduclof
to the neu#al (white) wire:
4 Remove the appI_ance harness
grounding
wie (green with yellow
sir pes) from the hte_d_
gro_nding
conDo©taR
5 Connect
the grounding
wi_e
(green wlfh yellow stripes) and the
neutral @_hto) wi_e d the power
supply cord o direct wire cable
to
the center, siiver co ored terminal
ecew of the terr:nk_ei b_ock,
Connect
the other wies to the
alter
tem_inals. Tighten screws (see
Fgure
3).
& Connect
o sepon_te copper
grounding
wire (NO
0 rain mum)
See
Connection
details*" for
detai ed ns*ructions,
7 Tighlen s#an reief screws.
8 Replace the terraria
biock cover.
F_re
t4
Use g_ound r_g wre and clamp
e_embty
(Ra_t NO, 685463) or NO-10
gauge
m_r_ihurn eopt_
g_eund ng
wre.
F{gure 15
Connect
ground_
"w_re_ a
grounded
cold ware
pipe*
wth he
e_amp and then to the extemc4
ground
ng conneeIOr
on the
washed!dryer
(see F_gures 14 and ! 5)
Do Not ground to a gas supply pipe or
hot water plpe_ Do Not connect
the
power supply cord to el_ctrtcal
power
supply until the washer ld_¥er is
permanently
grounded,
* O_ourlded c_,_ld water pipe must t _"_ve
meta car4 nui*y to eiectricai grc_._nd
and not be nfe rupted by plastic, tubby)
OI o!her elecff col ir_sulaN-igr;ohPectors
su_chas hoses f fling& washers or gasket_
{ino_x_i_ water meter or pump) Any
electrical ir/_Jlating connector _neuld be
jumped as shewn tr__igure 16 w*lh a
length of No-4 wte _cure y c_amped to
bare rr,e o! at beth e_ds,
_aust
requirement:
Do No_ use non-met@ t@×ibJe vent,
metal vent that is smolder than _ou
riches in diameter
or exhaust heeds
wth magnet_
latch÷&
Do Not e×hausf draper _nto a chimney
turt-_ace cold ar duc_ attic or oraw_
spaco, or any other duct u_d
for
ven_ing
DO Not }nsto i fiex b_e vent in enclosed
wa_ls, ce_hgs or floes
If using on existing exhaust system,
cleon lint from entire length of exhaust
sys_m. Mo_e sure exhaust hoo_l is not
plugged with tint.
The exhaust system should be inspected
and cleaned yeorly_
I_eplaee any vinyl at melailtzed
p_ostte
foil exhaust vent wffh dgid meter ot
flexible metal 'vent,
U_
duct
tape
_o _al
at* jeints.
Do Not use
screws
to seeui_
vent
Four-inch
dgld metal
pipe
is preferred
Plan installation
to u_
the fewest
number
of e}bows
and
_u_ns
Metat ilextbie
vent should be _uly
extended
and supported
when the
dr/e
_s in iis final position, DO NOT KNK
OR CRUSH T4E VENL The metal flexible
vent must be fully e xten_d
to allow
c_equate
exhc_uetair to flew,
Allow as much room as possible when
using ebows
or makng turns, Bend vent
gradually
ra avoia kinkng
Remove
excess flex b_e vent to avoid sagg ng
and kink ng that may resutt n reduced
air few,
Panel C
Advertisement
