Page 1 Dell PowerConnect W-Series ArubaOS 6.2 Command-Line Interface Reference Guide...
Page 2: Copyright Information
® System . Dell™, the DELL™ logo, and PowerConnect™ are trademarks of Dell Inc. All rights reserved. Specifications in this manual are subject to change without notice. Originated in the USA. All other trademarks are the property of their respective owners.
Page 3 Introduction The Dell PowerConnect W-Series ArubaOS 6.2 command line interface (CLI) allows you to configure and manage your controllers. The CLI is accessible from a local console connected to the serial port on the controllers or through a Telnet or Secure Shell (SSH) session from a remote management console or workstation.
Page 4 Beacon Report Request frames. wlan handover-trigger-profile Configure a handover trigger profile to ensure QoS for voice calls. wlan rrm-ie-profile This command configure an radio resource management RRM IE profile 4 | Introduction Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 5: Modified Commands
The rcp (Revocation Checkpoint) parameter was added. The rcp checks the revocation status of the SSH user’s client certificate before permitting access. provision-apsch-mode-radio-0 sch- If you are provisioning an 802.11n-capable AP, issue the sch-mode-radio- Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide Introduction | 5...
Page 6 VLAN assignment is based on the station MAC address. wlan dot11k-profile The following parameters were introduced: bcn-req-chan-11a bcn-req-chan-11bg ap-chan-rpt-11a ap-chan-rpt-11bg handover-trigger-profile rrm-ie-profile bcn-rpt-req-profile tsm-req-profile The handover trigger threshold parameter was deprecated, as the hand- 6 | Introduction Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 7: Deprecated Commands
802.1p values to an interface or policer profile. show papi-security (deprecated) Shows a configured papi-security profile. show policer-profile (deprecated) This command displays the policer profile configuration. show qos-profile (deprecated) This command displays the QoS profile configuration. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide Introduction | 7...
Page 8: About This Guide
This is typically performed when you run the Initial Setup on the controller, as described in the Dell PowerConnect W-Series ArubaOS 6.2 Quick Start Guide . In certain deployments, you can also configure a loopback address for the controller; see "interface loopback"...
Page 9: Cli Access
When typed at the end of a possible command or abbreviation, the question mark lists the commands that match (if any). For example: (host) > c? clear Clear configuration clock Configure the system clock configure Configuration Commands copy Copy Files Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide Introduction | 9...
Page 10: Command Completion
(host) (config-priority-map) # no dscp priority high Saving Configuration Changes Each Dell controller contains two different types of configuration images. The running-config holds the current controller configuration, including all pending changes which have yet to be saved. To view the running-config, use the following command:...
Page 11: Typographic Conventions
|wmm-be-dscp <best-effort>|wmm-bk-dscp <background>|wmm-ts- min-inact-int <milliseconds>|wmm-vi-dscp <video>|wmm-vo-dscp <voice>|wpa-hexkey <psk> |wpa-passphrase <string> } wlan dotllk <profile-name> {bcn-measurement-mode|dot11k- enable|force-dissasoc Typographic Conventions The following conventions are used throughout this manual to emphasize important concepts: Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide Introduction | 11...
Page 12: Command Line Editing
Move the cursor one character left. left arrow Ctrl D Delete Right Delete the character to the right of the cursor. Ctrl E Move the cursor to the end of the line. 12 | Introduction Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 13 W-3000 series controller, or a W-6000M3 controller module installed in a W-6000 controller chassis. Port numbers start at 0 from the left-most position. Use the show port status command to obtain the interface information currently available from a controller. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide Introduction | 13...
Page 14: Contacting Dell
Contacting Dell Table 5: Dell Contacts Contact Center Online Main Website dell.com Support Website dell.com/support Documentation Website dell.com/support/manuals 14 | Introduction Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 15 If you have not yet defined a netdestination, netdestination use the CLI command define a destination host or subnet before Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide aaa authentication captive-portal | 15...
Page 16 Logon wait CPU utilization threshold parameter. Enables a pop-up window with the Logout enabled/ enabled logout-popup- window link that allows the user to log out. If this disabled 16 | aaa authentication captive-portal Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 17 This parameter requires the Public Access disabled license. Sends the user’s VLAN ID in the redirection — — user-vlan-redirection-url URL when external captive portal servers are used. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide aaa authentication captive-portal | 17...
Page 18: Usage Guidelines
Command Information Licensing Command Mode Platforms All platforms Base operating system, except for Config mode on master controllers noted parameters 18 | aaa authentication captive-portal Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 19: Aaa Authentication Dot1X
— “default” <profile> name must be 1-63 characters. Clear the Cached PMK, Role and VLAN entries. This — — clear command is available in enable mode only. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide aaa authentication dot1x | 19...
Page 20 Select this option to enforce machine authentication — disabled enable before user authentication. If selected, either the machine-default-role or the user-default-role is assigned to the user, depending on which authentication is successful. 20 | aaa authentication dot1x Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 21 Server group retry interval, in seconds. 5-65535 server-retry-period <seconds> seconds Server certificate used by the controller to — — server-cert <certificate> authenticate itself to the client. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide aaa authentication dot1x | 21...
Page 22 Interval, in seconds, between unicast key rotation. ukey-rotation-period 864000 seconds <seconds> Interval, in milliseconds, between unicast and 0-2000 0 ms wpa-groupkey multicast key exchanges. (no delay) -delay <milliseconds> 22 | aaa authentication dot1x Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 23 (also called “AAA FastConnect”). In the AAA profile, specify the 802.1X authentication profile, the default role for authenticated users, and the server group for the authentication. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide aaa authentication dot1x | 23...
Page 24 The cert-cn-lookup, enforce-suite-b-128 and enforce-suite-b-192 parameters were introduced. Command Information Platforms Licensing Command Mode All platforms Base operating system. The voice- Config mode on master controllers aware parameter requires the PEFNG license 24 | aaa authentication dot1x Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 25: Aaa Authentication Mac
Users may be required to authenticate themselves using other methods, depending upon the network privileges. Example The following example configures a MAC authentication profile to blacklist client devices that fail to authenticate. aaa authentication mac mac-blacklist max-authentication-failures 3 Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide aaa authentication mac | 25...
Page 26 In earlier versions of ArubaOS, the max-authentication-failures parameter required the Wireless Intrusion Protection license Command Information Platforms Licensing Command Mode All platforms Base operating system Config mode on master controllers 26 | aaa authentication mac Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 27 The following example configures a management authentication profile that authenticates users against the controller’s internal database. Users who are successfully authenticated are assigned the read-only role. aaa authentication mgmt Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide aaa authentication mgmt | 27...
Page 28 The network-operations role was introduced. ArubaOS 3.3 The location-api-mgmt role was introduced. Command Information Platforms Licensing Command Mode All platforms Base operating system Config mode on master controllers 28 | aaa authentication mgmt Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 29 Command History This command was available in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Config mode on master or local controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide aaa authentication-server internal | 29...
Page 30 Enables the LDAP server. — Filter that should be applied to search of the user in the — (objectclass=*) filter <filter> LDAP database. The default filter string is (objectclass=*). 30 | aaa authentication-server ldap Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 31 (objectclass=*) enable Command History This command was available in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide aaa authentication-server ldap | 31...
Page 32 The maximum length is 128 characters. mac-lowercase Send MAC addresses as lowercase. — — nas-identifier <string> Network Access Server (NAS) identifier to use in — — RADIUS packets. 32 | aaa authentication-server radius Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 33 Command History Version Modification ArubaOS 3.0 Command introduced. ArubaOS 6.0 RADIUS server can be identified by its qualified domain name (FQDN). ArubaOS 6.1 The source-interface parameter was added. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide aaa authentication-server radius | 33...
Page 34 Command Information Platforms Licensing Command Mode All platforms Base operating system Config mode on master controllers 34 | aaa authentication-server radius Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 35 (see "aaa server-group" on page 82). Example The following command configures, enables a TACACS+ server and enables session authorization: aaa authentication-server tacacs tacacs1 clone default Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide aaa authentication-server tacacs | 35...
Page 36 Description ArubaOS 3.0 Command introduced. ArubaOS 6.0 session-authorization parameter was introduced. Command Information Platforms Licensing Command Mode All platforms Base operating system Config mode on master controllers 36 | aaa authentication-server tacacs Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 37 10.1.1.245 enable Command History This command was available in ArubaOS 3.4.1 Command Information Platforms Licensing Command Mode All platforms Base operating system Config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide aaa authentication-server windows | 37...
Page 38 38 | aaa authentication-server windows Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 39 10 seconds timeout <seconds> Usage Guidelines This command configures 802.1X authentication for clients on non-Dell APs. The controller maintains user session state information for these clients. Example The following command assigns the employee user role to clients who successfully authenticate with the server group...
Page 40 Description This command clears automatically-created control path entries for 802.1X users on non-Dell APs. Syntax No parameters. Usage Guidelines Run this command after changing the configuration of a RADIUS server in the server group configured with the aaa authentication stateful-dot1x command.
Page 41 The following example configures a stateful NTLM authentication profile that authenticates clients via the server group “Windows1.” Users who are successfully authenticated are assigned the “guest2” role. aaa authentication stateful-ntlm default-role guest2 server-group Windows1 Command History Command introduced in ArubaOS 3.4.1 Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide aaa authentication stateful-ntlm | 41...
Page 42 Command Information Platforms Licensing Command Mode All platforms Base operating system Config mode on master controllers 42 | aaa authentication stateful-ntlm Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 43 (host) (VIA Authentication Profile "default") #server-group "via-server-group" Command History Command introduced in 5.0 Command Information Platforms Licensing Command Mode All platforms Base operating system Config mode on master or local controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide aaa authentication via auth-profile | 43...
Page 44 <map> number <number> ipsecv2-cryptomap lockdown-all-settings max-reconnect-attempts <max-reconnect-attempts> minimized max-timeout <value> minimized save-passwords server split-tunneling suiteb-crypto support-email tunnel validate-server-cert whitelist windows-credentials Description This command configures the VIA connection profile. 44 | aaa authentication via connection-profile Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 45 Zero Config (WZC) to configure or manage their wireless networks. position <position> — Create a copy of connection profile from an clone — another VIA connection profile. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide aaa authentication via connection-profile | 45...
Page 46 List of IKE V2 policies that the VIA Client has to ikev2-policy — use to connect to the controller Enable this to use IKEv2 protocol to establish VIA Disabled ikev2-proto 46 | aaa authentication via connection-profile Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 47 VIA client. Enter tunneled IP address and its netmask. netmask <netmask> — Enable or disable VIA from validating the server Enabled validate-server-cert Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide aaa authentication via connection-profile | 47...
Page 48 (host) (VIA Connection Profile "via") #support-email via-support@example.com Command History Release Modification ArubaOS 5.0 Command introduced ArubaOS 6.1 The following commands were introduced: admin-logon-script admin-logoff-script ikev2-policy ikev2-proto ikev2-auth ipsecv2-crypto minimized 48 | aaa authentication via connection-profile Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 49 The following commands were introduced: allow-whitelist-traffic banner-message-reappear-timeout controllers-load-balancing enable-fips enable-supplicant whitelist Command Information Platforms Licensing Command Mode All platforms Base operating system Config mode on master or local controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide aaa authentication via connection-profile | 49...
Page 50 (host) (config) #aaa authentication via global-config Command History Command introduced in 5.0 Command Information Platforms Licensing Command Mode All platforms Base operating system Config mode on master or local controllers 50 | aaa authentication via global-config Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 51 (host) (VIA Web Authentication "default") #auth-profile default position 0 Command History Command introduced in 5.0 Command Information Platforms Licensing Command Mode All platforms Base operating system Config mode on master or local controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide aaa authentication via web-auth | 51...
Page 52 This command configures VPN authentication settings for VPN, RAP and CAP clients.Use the vpdn group command to configure Layer-2 Tunneling Protocol and Internet Protocol Security (L2TP/IPsec) or a Point-to-Point Tunneling Protocol (PPTP) VPN connection. (See "vpdn group l2tp" on page 1456.) 52 | aaa authentication vpn Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 53 All platforms Base operating system, except for Config mode on master controllers noted parameters. The default-role parameter requires the Policy Enforcement Firewall for VPN Users (PEFV) license. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide aaa authentication vpn | 53...
Page 54: Related Commands
VLAN or port on the controller. Command History This command was available in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Config mode on master controllers 54 | aaa authentication wired Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 55 Range: 1-10 seconds. Default: 5 seconds. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide aaa authentication wispr | 55...
Page 56 NOTE: A Boingo smart client uses a NAS identifier in the format <CarrierID>_<VenueID> for location identification. To support Boingo clients, you must also configure the NAS identifier parameter in the Radius server profile for the WISPr server 56 | aaa authentication wispr Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 57 Command History This command was available in ArubaOS 3.4.1. Command Information Platforms Licensing Command Mode All platforms Base operating system Config mode on master or local controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide aaa authentication wispr | 57...
Page 58 1 Command History This command was available in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Config mode on master controllers 58 | aaa bandwidth-contract Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 59 Describes the user derivation rule. This parameter is optional and has a 128 character description maximum. Position of this rule relative to other rules that are configured. position Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide aaa derivation-rules | 59...
Page 60 ESSID to which the client is associated equals does not equal macaddr: MAC address of the client One of the following: MAC address (xx:xx:xx:xx:xx:xx) contains ends with equals does not equal starts with 60 | aaa derivation-rules Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 61 00:26:c6:52:6b:7c reqIP=10.10.10.254 Options 3d:010026c6526b7c 36:0a0a0a02 0c:41525542412d46416c73653232 51:00000041525542412d46416c736532322e73757279612e636f6d 3c:4d53465420352e30 37:010f03062c2e2f1f21f92b 2b:dc0100 Feb 26 02:53:04 :202536: <DBUG> |dhcpdwrap| |dhcp| Datapath vlan10: REQUEST 00:26:c6:52:6b:7c reqIP=10.10.10.254 Options 3d:010026c6526b7c 36:0a0a0a02 0c:41525542412d46416c73653232 51:00000041525542412d46416c736532322e73757279612e636f6d 3c:4d53465420352e30 37:010f03062c2e2f1f21f92b 2b:dc0100 Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide aaa derivation-rules | 61...
Page 62 Command Information Platforms Licensing Command Mode All platforms Base operating system. The PEFNG Config mode on master controllers license must be installed for a user role to be assigned. 62 | aaa derivation-rules Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 63 Command History This command was available in ArubaOS 6.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Config mode on local and master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide aaa dns-query-interval | 63...
Page 64 Command History This command was available in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable mode on master controllers 64 | aaa inservice Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 65 The following commands create a role that logs HTTPS traffic, then assign the role to a specific IPv6 client: ip access-list session ipv6-log-https any any svc-https permit log user-role ipv6-web-debug session-acl ipv6-log-https In enable mode: 2002:d81f:f9f0:1000:e409:9331:1d27:ef44 aaa ipv6 user add role ipv6-web-debug Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide aaa ipv6 user add | 65...
Page 66 Command History This command was available in ArubaOS 3.3. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable mode on master controllers 66 | aaa ipv6 user add Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 67 Command History This command was available in ArubaOS 3.3. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide aaa ipv6 user clear-sessions | 67...
Page 68 Command History This command was available in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable mode on master controllers 68 | aaa ipv6 user delete Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 69 Command History This command was available in ArubaOS 3.3. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide aaa ipv6 user logout | 69...
Page 70 Range: 0-10 digits. By default, there is no requirement for numerical digits in a password, and the parameter has a default value of 0. The minimum number of characters required for a management user password-min-length 70 | aaa password-policy mgmt Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 71 $ equals sign: = percent sign: % slash: / caret: ^ question mark: ? ampersand: & star: * greater and less than symbols: < > Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide aaa password-policy mgmt | 71...
Page 72: Related Commands
Command History This command was available in ArubaOS 5.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable mode on master controllers 72 | aaa password-policy mgmt Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 73: Aaa Profile
If derivation rules are present, the role assigned to the client through these rules take precedence over the default role. NOTE: This parameter requires the PEFNG license. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide aaa profile | 73...
Page 74 The AAA profile defines the user role for unauthenticated users, the default user role for MAC or 802.1X authentication, and user derivation rules. The AAA profile contains the authentication profile and authentication 74 | aaa profile Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 75 Policy Enforcement Firewall license instead of the Voice Services Module license required in earlier versions. ArubaOS 6.1 The radius-interim-accounting, devtype-classification and enforce-dhcp parameters were introduced. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide aaa profile | 75...
Page 76 Command Information Platforms Licensing Command Mode All platforms Base operating system, except for Config mode on master controllers noted parameters 76 | aaa profile Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 77 0\202\005\2240\202\004|\240\003\002\001\002\002\012\037\177\374\305 givenName: JDE distinguishedName: CN=John Doe,CN=Users,DC=eng,DC=net instanceType: 4 whenCreated: 20060516232817.0Z whenChanged: 20081216223053.0Z displayName: John Doe uSNCreated: 24599 memberOf: CN=Cert_Admins,CN=Users,DC=eng,DC=net memberOf: CN=ATAC,CN=Users,DC=eng,DC=net uSNChanged: 377560 department: eng name: John Doe Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide aaa query-user | 77...
Page 78 Command History This command was available in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable mode on master controllers 78 | aaa query-user Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 79 RADIUS attributes recognized by the controller. To add a RADIUS attribute to the list, use the aaa radius-attributes command. Example The following command adds the VSA “Dell-User-Role”: aaa radius-attributes add Dell-User-Role 1 string vendor Dells 14823 Command History This command was available in ArubaOS 3.0. Command Information...
Page 80 If no matching user is found the controller will send a 503: Session Not Found error message back to the RFC 3576 server. Example The following command configures an RFC 3576 server: aaa rfc-3576-server 10.1.1.245 clone default key P@$$w0rD; 80 | aaa rfc-3576-server Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 81 View information for a user whose session timeout is altered by a RFC 3576 server. Command History Version Description ArubaOS 3.0 Comand introduced Command Information Platforms Licensing Command Mode All platforms Base operating system Config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide aaa rfc-3576-server | 81...
Page 82 The rule matches if the user/client information starts with the starts-with — specified string. match-fqdn <string> This option associates the authentication server with a specified — 82 | aaa server-group Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 83 (in which case, the next server in the list is used). You can configure servers of different types in a server group, for example, you can Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide aaa server-group | 83...
Page 84 Class value-of Command History This command was introduced in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Config mode on master controllers 84 | aaa server-group Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 85 This command configures the user role assigned to clients that fail Sygate On-Demand Agent (SODA) remediation. Command History Version Description ArubaOS 3.0 Command introduced ArubaOS 3.4 Command deprecated Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide aaa sygate-on-demand (deprecated) | 85...
Page 86 Command History This command was available in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Config mode on master controllers 86 | aaa tacacs-accounting Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 87 Authentication successful Command History This command was available in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide aaa test-server | 87...
Page 88 300 to 600 seconds) Usage Guidelines These parameters can be left at their default values for most implementations. Example The following command changes the idle time to 10 minutes: 88 | aaa timers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 89 ArubaOS 3.0 Command introduced Idle timeout values and defaults changed ArubaOS 3.4 Command Information Platforms Licensing Command Mode All platforms Base operating system Config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide aaa timers | 89...
Page 90 Parameter Description <macaddr> MAC address of the AP Usage Guidelines This command configures a non-Dell AP as a trusted AP. Example The following command configures a trusted non-Dell AP: aaa trusted-ap 00:40:96:4d:07:6e Command History This command was available in ArubaOS 3.0.
Page 91 The following commands create a role that logs HTTPS traffic, then assign the role to a specific client: ip access-list session log-https any any svc-https permit log user-role web-debug Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide aaa user add | 91...
Page 92 10.1.1.236 role web-debug Command History This command was available in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable mode on master controllers 92 | aaa user add Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 93 10.1.1.236 Command History This command was available in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide aaa user clear-sessions | 93...
Page 94 Command History This command was available in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable mode on master controllers 94 | aaa user delete Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 95 (or an AP connected to an untrusted port on the controller) changes its IP address. Command History This command was available in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide aaa user fast-age | 95...
Page 96 10.1.1.236 Command History This command was available in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable mode on master controllers 96 | aaa user logout Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 97 10.1.1.236 Command History This command was available in ArubaOS 6.2. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide aaa user monitor | 97...
Page 98 The server configured with this command is referenced in the AAA profile for the WLAN (see "aaa profile" on page 73). Contact your Dell representative for more information about using the XML API. Example The following configures an XML API server: aaa xml-api server 10.210.1.245...
Page 99 VLAN used) Usage Guidelines Dell APs send out periodic multicast and broadcast queries to locate the master controller. If the APs are in the same broadcast domain as the master controller and ADP is enabled on the controller, the controller automatically responds to the APs’...
Page 100 Wired MAC table or the Ethernet MAC table. Usage Guidelines These commands are intended to be used with an Dell AP that is configured as an air monitor. You should not use the am test command unless instructed to do so by an Dell representative.
Page 101 Command Information Platforms Licensing Command Mode All platforms Base operating system Enable and Config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide am | 101...
Page 102 1508. profile Configures 802.11g radio settings and load balancing — “default” dot11g-radio-profile for the AP group; contains the ARM profile. See "rf dot11a-radio-profile" on page 519. 102 | ap-group Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 103 Commands to configure mesh for outdoor APs require the Outdoor Mesh license. Negates any configured parameter. — — Configures the country code and valid channels. See — “default” regulatory-domain-profile "ap regulatory-domain-profile" on page 146. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide ap-group | 103...
Page 104: Related Commands
The voip-cac-profile parameter requires the PEFV license. ArubaOS 6.0 The enet-port-profile parameters parameters were introduced. Command Information Platforms Licensing Command Mode All platforms Base operating system, except for Config mode on master controllers noted parameters 104 | ap-group Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 105 AP system profile is set to “normal” then the normal parameter in this command will allow the LEDs light as usual. Example The following command causes all local APs to blink their LEDs for identification purposes: ap-leds all local blink Command History Release Modification ArubaOS 3.0 Command introduced Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide ap-leds | 105...
Page 106 Command Information Platforms Licensing Command Mode Available on all platforms Base operating system Config mode on master or local controllers 106 | ap-leds Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 107 Configures 802.11g radio settings for the AP group; contains the ARM “default” dot11g-radio- profile. See "rf dot11a-radio-profile" on page 519. profile Configures bandwidth allocation. See "wlan traffic-management- — dot11g-traffic- Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide ap-name | 107...
Page 108 Profiles that are applied to an AP group can be overridden on a per-AP name basis, and virtual APs can be added or excluded on a per-AP name basis. If a particular profile is overridden for an AP, all parameters from the overriding 108 | ap-name Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 109 PEF license instead of the Voice Services Module license required in earlier versions. Command Information Platforms Licensing Command Mode All platforms Base operating system Config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide ap-name | 109...
Page 110 (host)(config) #ap-regroup wired-mac 00:0f:1e:11:00:00 corpnet Command History This command was introduced in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable and Config mode on master controllers 110 | ap-regroup Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 111 (host) (config) #ap-rename wired-mac 00:0f:1e:11:00:00 building3-lobby Command History This command was introduced in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable and Config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide ap-rename | 111...
Page 112 Command History Release Modification ArubaOS 5.0 Command introduced Command Information Platforms Licensing Command Mode Available on all platforms Base operating system Config mode on master or local controllers 112 | ap authorization-profile Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 113 Usage Guidelines You should not normally need to use this command as APs automatically reboot when you reprovision them. Use this command only when directed to do so by your Dell representative. Example The following command reboots a specific AP:...
Page 114 BSSID of the parent to which the mesh point should connect. parent-bssid <bssid> Usage Guidelines To maintain a mesh topology created using the apconnect command, Dell suggests setting the mesh reselection- mode to reselect-never, otherwise the normal mesh reselection mechanisms could break up the selected topology. Example The following command connects the mesh point “meshpoint1”...
Page 115 Enable or Config mode Command History This command was introduced in ArubaOS 3.2 Command Information Platforms Licensing Command Mode All platforms Base operating system Enable and Config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide apdisconnect | 115...
Page 116 [deprecated] apflash all|{ap-group <group>}|{ap-name <name>}|{ip-addr <ipaddr>}|{wired-mac <macaddr>} global|local [backup-partition] [server <ipaddr>] Description This command reflashes the specified AP. Starting with ArubaOS 6.1, this command can only be run by Dell Technical Support or users in support mode. Command History Version Description ArubaOS 3.0...
Page 117 [ap-name <name>|ip-addr <ip-addr>|ip6-addr <ip6-addr>] [filename <filename> {all|interrupt|qcu |radio}] Description This command allows you to collect all or specific radio register information into a separate file. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide ap debug radio-registers dump | 117...
Page 118 #ap debug radio-registers dump ap-name myap1 filename myradioregfile all Command History Introduced in ArubaOS6.2. Command Information Platforms Licensing Command Mode 802.11n-capable APs Base operating system Enable mode on master controllers 118 | ap debug radio-registers dump Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 119 This command configures the duplex and speed of the Ethernet port on the AP. The configurable speed is dependent on the port type. Example The following command configures the Ethernet link profile for full-duplex and 100 Mbps: ap enet-link-profile enet duplex full speed 100 Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide ap enet-link-profile | 119...
Page 120 Support for 1000 Mbps (1 Gbps) Ethernet port speed was introduced. ArubaOS 6.2 Support for the dot3az parameter was introduced. Command Information Platforms Licensing Command Mode Available on all platforms Base operating system Config mode on master controllers 120 | ap enet-link-profile Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 121 Use this application type if the AP services IP telephones and voice other appliances that support interactive voice services. NOTE: This is the default application type. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide ap lldp med-network-policy-profile | 121...
Page 122 Next, the LLDP MED network policy profile is assigned to an LLDP profile, and the LLDP profile is associated with an AP wired-port profile. (host) (config) ap lldp profile video1 (host) (AP LLDP Profile "video1")lldp-med-network-policy-profile vid-stream (host) (AP LLDP Profile "video1")! (host) (config)ap wired-port-profile corp2 122 | ap lldp med-network-policy-profile Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 123 Command History This command was introduced in ArubaOS 6.2. Command Information Platforms Licensing Command Mode Available on all platforms Base operating system Config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide ap lldp med-network-policy-profile | 123...
Page 124 NOTE: This parameter is supported by the W-IAP3WNP and W-AP130 series only. lldp-med-network-policy-profile Specify the LLDP MED Network Policy profile to be associated with this LLDP profile. <profile> 124 | ap lldp profile Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 125 Link Layer Discovery Protocol (LLDP), is a Layer-2 protocol that allows network devices to advertise their identity and capabilities on a LAN. Wired interfaces on Dell APs support LLDP by periodically transmitting LLDP Protocol Data Units (PDUs) comprised of type-length-value (TLV) elements. Use this command to specify which TLVs should be sent by the AP interface associated with the LLDP profile.
Page 126 Command History This command was introduced in ArubaOS 6.2. Command Information Platforms Licensing Command Mode Available on all platforms Base operating system Config mode on master controllers 126 | ap lldp profile Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 127 When you first create a new mesh cluster profile, the profile uses the default cluster name “Dell-mesh”. Use the cluster parameter to define a new, unique MSSID before you assign APs or AP groups to the mesh cluster profile.
Page 128: Related Commands
<name> Command History This command was introduced in ArubaOS 3.2. Command Information Platforms Licensing Command Mode All platforms Base operating system. Config mode on master controllers 128 | ap mesh-cluster-profile Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 129 SSID. This parameter is enabled by default. If enabled, the AP will advertise Low-density Parity enabled ldpc Check (LDPC) support. LDPC improves data transmission over radio channels with high levels of Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide ap mesh-ht-ssid-profile | 129...
Page 130 AP transmits data again. An AP identifies any signal content received inside this interval as unwanted inter-symbol interference, and rejects that data. The 802.11n standard specifies two guard intervals: 130 | ap mesh-ht-ssid-profile Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 131 The following command configures a mesh high-throughput SSID profile named “HT1” and sets some non-default settings for MAC protocol data unit (MPDU) aggregation: (host) (config) #ap mesh-ht-ssid-profile HT1 max-rx-a-mpdu-size 32767 max-tx-a-mpdu-size 32767 min-mpdu-start-spacing .25 Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide ap mesh-ht-ssid-profile | 131...
Page 132 Command introduced ArubaOS 6.1 The short-guard-intvl-20Mhz, ldpc, stbc-rx-streams and stbc-rx-streams parameters were introduced. Command Information Platforms Licensing Command Mode All platforms Base operating system Config mode on master controllers 132 | ap mesh-ht-ssid-profile Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 133 EAPOL frames and mesh echoes. disabled Indicates the transmit rates for the 802.11b/g radio. 1, 2, 5, 6, 9, 11, 1, 2, 5, 6, 9, 11, g-tx rates Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide ap mesh-radio-profile | 133...
Page 134 This is a beta feature that is disabled by rssi default; it should not be enabled unless you are instructed to do so by Dell technical suppport. Specifies the algorithm used by a mesh node to — distributed- metric- select its parent.
Page 135 Connected mesh nodes evaluate alternative links only — — subthreshold-only if the existing uplink becomes a sub-threshold link. NOTE: Starting with ArubaOS 3.4.1, if a mesh point using the subthreshold-only mode reselects a more Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide ap mesh-radio-profile | 135...
Page 136 ArubaOS 3.2 Command introduced. ArubaOS 3.2.0.x, 3.3.1.x The tx-power default increased from 14 to 30 dBm. ArubaOS 3.3 The heartbeat-threshold default increased from 5 to 10 heartbeat messages. 136 | ap mesh-radio-profile Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 137 ArubaOS 6.1 The eapol-rate-opt parameter was introduced. Command Information Platforms Licensing Command Mode All platforms Base operating system Config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide ap mesh-radio-profile | 137...
Page 138 Set the priority of the wired uplink. Each uplink type has 0-255 clone <source> an associated priority; wired ports having the highest priority by default. 138 | ap provisioning-profile Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 139 AP. NOTE: This parameter can only be used on the master controller. If you configure an uplink VLAN on an AP connected to a uplink-vlan <uplink-vlan> Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide ap provisioning-profile | 139...
Page 140 PANTECH USB driver for 3G/2G devices sierra-evdo:EVDO Sierra Wireless driver sierra-gsm: GSM Sierra Wireless driver The PPP username provided by the cellular service — — usb-user provider 140 | ap provisioning-profile Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 141 The following new parameters were introduced for provisioning APs for 802.1X authentication: apdot1x-passwd apdot1x-username The following new parameters were introduced for provisioning Remote APs using USB modems: usb-modeswitch Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide ap provisioning-profile | 141...
Page 142 <ap-name|ip-addr|ip6-addr> Description These commands manage WiFi packet capture (PCAP) on Dell APs. The WiFi packets are encapsulated in a UDP header and sent to a client running a packet analyzer like Wildpacket’s Airopeek, Omnipeek, or Wireshark.
Page 143 In the capture window, the timestamp displayed corresponds to the time that the packet is recevied by the client and is not synchronized with the time on the Dell AP. Filter specification (used in ap packet-capture interactive) supports the following:...
Page 144 Command History Version Change ArubaOS3.0 Command Introduced ArubaOS3.4 The maxlen parameter was introduced, and the pcap start command deprecated. ArubaOS6.2 Name changed from pcap to ap packet capture. 144 | ap packet-capture Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 145 Command Information Platforms Licensing Command Mode All platforms Base operating system Works in Access Point, Air Monitor, and Spectrum Monitor modes on all AP models in enable mode. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide ap packet-capture | 145...
Page 146 The two channels must be Note: Changing the country separated by a dash. code causes the valid channel Example: lists to be reset to the defaults 146 | ap regulatory-domain-profile Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 147 Related Commands To view the supported channels, use the show ap allowed-channels command. AP configuration settings related to the IEEE 802.11n standard are configurable for Dell’s W-AP120 series access points, which are IEEE 802.11n standard compliant devices. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 148 + and - parameters that allowed you to define a primary and backup channel within the channel pair. Command Information Platforms Licensing Command Mode All platforms Base operating system Config mode on master controllers 148 | ap regulatory-domain-profile Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 149 Command History Introduced in ArubaOS 6.2. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide ap remove-r1-key | 149...
Page 150 (deprecated) Description This command configures an SNMP profile for APs. Command History Version Modification ArubaOS 3.0 Command introduced ArubaOS 3.4 Command deprecated 150 | ap snmp-profile (deprecated) Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 151 ... priv-passwd <password> user-name <name> Description This command configures an SNMPv3 user profile for APs. Command History Version Modification ArubaOS 3.0 Command introduced ArubaOS 3.4 Command deprecated Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide ap snmp-user-profile (deprecated) | 151...
Page 152 Command History Introduced in ArubaOS 6.0. Command Information Platforms Licensing Command Mode All platforms RF Protect license Config mode on master or local controllers 152 | ap spectrum clear-webui-view-settings Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 153 The spectrum-band parameter supports a 5ghz value, allowing an AP to monitor the entire 5 Ghz radio band. Previous versions of ArubaOS supported 5ghz-lower, 5ghz-middle and 5ghz- upper settings. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide ap spectrum local-override | 153...
Page 154 Command Information Platforms Licensing Command Mode All platforms RF Protect license Config mode on master controllers 154 | ap spectrum local-override Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 155 This command configures an AP system profile. Syntax Parameter Description Range Default <profile> Name of this instance of the profile. The name must be — “default” 1-63 characters. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide ap system-profile | 155...
Page 156 Define the DSCP value of AP heartbeats. 0-63 Use this feature to prioritize AP heartbeats and prevent the AP from losing connectivity with the controller over high-latency or low-bandwidth WAN connections. 156 | ap system-profile Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 157 Maximum number of times to retry AP-generated 1-65535 tries requests, including keepalive messages. After the maximum number of retries, the AP either tries the IP address specified by the bkup-lms-ip (if configured) or reboots. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide ap system-profile | 157...
Page 158 1-65535 10 seconds interval retries of AP-generated requests. If the configured interval is less than 30 seconds, the interval for subsequent retries is increased up to 30 seconds. 158 | ap system-profile Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 159 ArubaOS 5.0 The master-ip, rfprotect-server-ip and rfprotect-bkup-server parameters were deprecated. ArubaOS 6.0 Added support for the option to set the RF scanning band (am-scan-rf-band). The keepalive-interval parameter was deprecated. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide ap system-profile | 159...
Page 160 Command Information Platforms Licensing Command Mode All platforms Base operating system, except for Config mode on master controllers noted parameters 160 | ap system-profile Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 161 Usage Guidelines Use this command only under the supervision of Dell technical support. If you delete the current image in the AP’s flash memory, the AP will not function until you reload another image. Command History This command was introduced in 3.3.2.
Page 162 NOTE: Virtual APs in split-tunnel mode using static WEP should use key slots 2-4 on the controller. Key slot 1 should only be used with Virtual APs in tunnel mode. Negates any configured parameter. 162 | ap wired-ap-profile Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 163 Ethernet port (enet1) on the AP. For mesh deployments, this command is applicable to all Dell APs configured as mesh nodes. If you are using mesh to join multiple Ethernet LANs, configure and enable bridging on the mesh point Ethernet port.
Page 164 Command Information Platforms Licensing Command Mode All platforms Base operating system, except for Config mode on master controllers noted parameters 164 | ap wired-ap-profile Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 165 This command is only applicable to APs with Ethernet ports. Issue this command to enable or disable the wired port, define an AAA profile for wired port devices, and associate the port with an ethernet link profile that defines its speed and duplex values. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide ap wired-port-profile | 165...
Page 166 Command History This command was introduced in ArubaOS 6.0 Command Information Platforms Licensing Command Mode All platforms Base operating system, except for Config mode on master controllers noted parameters 166 | ap wired-port-profile Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 167 (host) (config) #arp 10.152.23.237 00:0B:86:01:7A:C0 Command History This command was introduced in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide arp | 167...
Page 168: Audit Trail
The following command enables an audit trail: (host) (config) #audit-trail Command History This command was introduced in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Config mode on master controllers 168 | audit-trail Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 169 (host)(config) #backup flash Command History This command was introduced in ArubaOS 3.0. Command Information Licensing Command Mode Platforms All platforms Base operating system Enable and Config modes on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide backup | 169...
Page 170: Banner Motd
Welcome to my controller. This controller is in the production network, so please do not save configuration changes. Zach Jennings is awesome. Maintenance will be performed at 7:30 PM, so please log off before 7:00 PM.* The banner display is as follows: 170 | banner motd Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 171 7:00 PM. Command History This command was introduced in ArubaOS 1.0 Command Information Platforms Licensing Command Mode All platforms Base operating system Config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide banner motd | 171...
Page 172 Printing the extra debugging information is disabled using the command. no boot verbose Example The following command uses the configuration file january-config.cfg the next time the controller boots: boot config-file january-config.cfg 172 | boot Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 173 Introduced for the first time. ArubaOS 6.0 The remote-node parameter was introduced. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable and Config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide boot | 173...
Page 174 Enter the keyword no to negate the command and revert back to the defaults. Enter the keyword priority to override the default cellular priority priority <1-255> (100). Range: 1 to 255. Default: 100 174 | cellular profile Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 175 Command History Introduced in ArubaOS 3.4. Command Information Platforms Licensing Command Mode W-600 series controllers Base operating system Config mode on master and local controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide cellular profile | 175...
Page 176 By default, configuration updates on the controller are disabled to prevent any alterations to the controller configuration. Example The following command allows configuration updates from the Mobility Management System: (host)(config) #cfgm mms config enable 176 | cfgm Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 177 Command History This command was introduced in ArubaOS 3.1. Command Information Platforms Licensing Command Mode All platforms Base operating system Config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide cfgm | 177...
Page 178 Clear internal status of authentication modules. Parameters: configuration—clear all configured objects. debug-statistics—clear debug statistics. messages—clear authentication messages that were sent and received. Clear ACL statistics. Clear ACL hit statistics hits 178 | clear Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 179 Clears all SNMP fault configuration. fault Clears global AP database. This command is often used to clear all stale AP records. gap-db Use the following parameters: ap-name Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide clear | 179...
Page 180 AP related commands. Specify the BSSID of the AP. client—clear all wired client related commands. Specify the MAC address of the client. probe—clear all probe information. Specify the BSSID of the probe. 180 | clear Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 181 The following MLD parameters are added to the ipv6 option: mld group mld stats-counters Command Information Platforms Licensing Command Mode All platforms Base operating system Enable and Config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide clear | 181...
Page 182: Revision History
<mac>] Revision History Release Modification ArubaOS 6.1 Command introduced Command Information Platforms Licensing Command Mode All platforms Base operating system Enable and Config mode on master controllers 182 | clear wms wired-mac Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 183 The following example enables the timestamp feature. (host)(config) #clock append Command History This command was introduced in ArubaOS 6.2. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable mode Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide clock append | 183...
Page 184: Clock Set
(host)(config) #clock set 2007 jan 1 1 3 52 Command History This command was introduced in ArubaOS 1.0 Command Information Platforms Licensing Command Mode All platforms Base operating system Enable mode on master controllers 184 | clock set Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 185: Clock Summer-Time Recurring
You also have the option to set the number of hours by which to offset the clock from UTC. This has the same effect as the clock timezone command. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide clock summer-time recurring | 185...
Page 186 PST recurring 2 Sun Mar 2:00 first Sun Nov 3:00 -8 Command History This command was introduced in ArubaOS 1.0 Command Information Platforms Licensing Command Mode All platforms Base operating system Config mode on master controllers 186 | clock summer-time recurring Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 187: Clock Timezone
PST -8 Command History This command was introduced in ArubaOS 1.0 Command Information Platforms Licensing Command Mode All platforms Base operating system Config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide clock timezone | 187...
Page 188 : Define the controller as a cluster root, and set the IPsec key to authenticate that cluster member. NOTE: For information on installing certificates on your controller, refer to the Management Utilities chapter of the Dell PowerConnect W-Series ArubaOS User Guide .
Page 189 Command History. Introduced in ArubaOS 6.1. Command Information Platforms Licensing Command Mode All platforms Base operating system Config mode on cluster root controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide cluster-member-custom-cert | 189...
Page 190 : Define the controller as a cluster root, and set the IPsec key to authenticate that cluster member. NOTE: For information on installing certificates on your controller, refer to the Management Utilities chapter of the Dell PowerConnect W-Series ArubaOS User Guide .
Page 191 Command History Introduced in ArubaOS 6.1. Command Information Platforms Licensing Command Mode All platforms Base operating system Config mode on cluster root controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide cluster-member-factory-cert | 191...
Page 192 IPsec key ipseckey1: (host) (config) #cluster-member-ip 172.21.18.18 ipsec ipseckey1 Related Commands Parameter Description Mode control-plane-security Configure the control plane security profile. Config mode 192 | cluster-member-ip Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 193 Command History Introduced in ArubaOS 5.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Config mode on cluster root controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide cluster-member-ip | 193...
Page 194 APs from one hierarchy to failover to any other hierarchy by defining a cluster of master controllers. Each cluster will have one master controller as its cluster root, and all other master controllers as cluster members. 194 | cluster-root-ip Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 195 IPsec key or certificate for communication to the cluster root. NOTE: For information on installing certificates on your controller, refer to the Management Utilities chapter of the Dell PowerConnect W-Series ArubaOS User Guide . Example The following command defines the IPsec key for communication between the cluster member and the root controller172.21.45.22:...
Page 196: Configure Terminal
(host) # configure terminal Command History This command was introduced in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable mode on master controllers 196 | configure terminal Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 197 APs to the secure network by adding each AP's information to a campus AP whitelist. Example The following command defines a range of IP addresses that should receive certificates from the controller, and enables the control plane security feature: (host)(config) # control-plane-security Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide control-plane-security | 197...
Page 198 Command History This command was introduced in ArubaOS 5.0. Command Information Platforms Licensing Command Mode All platforms Base operating system. Config mode on master or local controllers 198 | control-plane-security Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 199 (host) (config) #show controller-ip Command History This command was introduced in ArubaOS 3.4 Command Information Platform License Command Mode Available on all platforms Base operating system Config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide controller-ip | 199...
Page 200 (host) (config) #show controller-ipv6 Command History This command is introduced in ArubaOS 6.1. Command Information Platform License Command Mode Available on all platforms Base operating system Config mode on master controllers 200 | controller-ipv6 Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 201 Copy the active, running configuration to a specified destination. Copy the configuration to the flash file system. flash: Specify the new name of the copied configuration file. filename Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide copy | 201...
Page 202 Specify the IP address or hostname of the TFTP server. tftphost Full name of the file to be copied. filename Copy the file to the flash file system flash: 202 | copy Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 203 (host) (config) #copy tftp: 192.0.2.0 engineering flash: default.bak copy flash: default.bak flash: default.cfg Command History This command was introduced in ArubaOS 1.0. Modification ArubaOS 1.0 Introduced for the first time. ArubaOS 6.2 The USB parameters introduced. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide copy | 203...
Page 204 Command Information Platforms Licensing Command Mode All platforms Base operating system Enable and Config modes on master controllers 204 | copy Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 205 ACL. Command History This command was introduced in ArubaOS 3.4 Command Information Platforms Licensing Command Mode All platforms This command requires the PEFNG Config mode on master controllers license. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide cp-bandwidth-contract | 205...
Page 206 ArubaOS. Command History This command was introduced in ArubaOS 6.1. Command Information Licensing Command Mode Platforms All platforms Base operating system Config mode on master controllers 206 | crypto-local ipsec sa-cleanup Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 207 Use one of the following: group1: 768-bit Diffie Hellman prime modulus group. group2: 1024-bit Diffie Hellman prime modulus group. group19: 256-bit random Diffie Hellman modulus group. group20: Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide crypto dynamic-map | 207...
Page 208 Example The following command configures a dynamic map: (host) (config)# crypto dynamic-map dmap1 100 set pfs group2 set security-association lifetime seconds 300 208 | crypto dynamic-map Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 209 All platforms The group19 and group20 PFS options requires the Config mode on master controllers Advanced Cryptography (ACR) license. All other parameters are available in the base operating system. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide crypto dynamic-map | 209...
Page 210 Example The following command configures 3DES encryption and MD5 authentication for a transform set named set2: (host) (config)# crypto ipsec transform-set set2 esp-3des esp-md5-hmac 210 | crypto ipsec Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 211 All platforms The esp-aes128-gcm and esp-aes56-gcm transform-set parameters require Config mode on master the Advanced Cryptography (ACR) license. All other parameters are controllers available in the base OS. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide crypto ipsec | 211...
Page 212 Configure the IP address for the group key. address <peer-address> An IP for the group key, in dotted-decimal format. Configure the netmask for the group key IP address. netmask 212 | crypto isakmp Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 213 Modification ArubaOS 3.0 Command introduced. ArubaOS 6.1 The eap-passthrough parameter was introduced. Command Information Platforms Licensing Command Mode All platforms Base operating system Config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide crypto isakmp | 213...
Page 214 Use the 768-bit Diffie Hellman prime modulus group. This is the default group setting. Use the 1024-bit Diffie Hellman prime modulus group. Use the 256-bit random Diffie Hellman ECP modulus group. 214 | crypto isakmp policy Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 215 Key:*******Re-Type Key:******* Command History Release Modification ArubaOS 3.0 Command introduced. ArubaOS 6.1 The following parameters were introduced. authentication ecdsa-256 authentication ecdsa-384 hash sha1-96 hash sha2-256-128 hash sha2-384-192 Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide crypto isakmp policy | 215...
Page 216 SHA-256-128, SHA-384-192 Diffie-Hellman (DH) Groups: 19 and 20 Pseudo-Random Function (PRF): PRF-HMAC-SHA256, PRF-HMAC-SHA384 Authentication: ecdsa-256 and ecdsa-384 All other parameters are supported in the base OS. 216 | crypto isakmp policy Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 217 Peer Certificate Subject Name field If you are using IKEv1 to establish a site- — — peer-ip <ipaddr> Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide crypto-local ipsec-map | 217...
Page 218 384-bit random Diffie Hellman ECP modulus group. (For IKEv2 only) Configures the lifetime, in seconds, for 300- 7200 set security-association lifetime the security association (SA). 86400 seconds seconds <seconds> 218 | crypto-local ipsec-map Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 219 The following commands configures site-to-site VPN between two controllers: (host) (config) #crypto-local ipsec-map sf-chi-vpn 100 src-net 101.1.1.0 255.255.255.0 dst-net 100.1.1.0 255.255.255.0 peer-ip 172.16.0.254 vlan 1 trusted (host) (config) #crypto-local ipsec-map chi-sf-vpn 100 Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide crypto-local ipsec-map | 219...
Page 220 <key> fqdn-any Command History Release Modification ArubaOS 3.0 Command introduced. ArubaOS 6.1 The peer-cert-dn and peer-fqdn parameters were introduced. The set pfs command introduced the group19 and group20 parameters. 220 | crypto-local ipsec-map Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 221 All platforms The group19 and group20 PFS Config mode on master controllers options requires the Advanced Cryptography (ACR) license. All other parameters are available in the base operating system. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide crypto-local ipsec-map | 221...
Page 222 TrustedCA1 Command History This command was introduced in ArubaOS 3.2. Command Information Platforms Licensing Command Mode All platforms Base operating system Config mode on master controllers 222 | crypto-local isakmp ca-certificate Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 223 TrustedCA Command History This command was introduced in ArubaOS 6.1. Command Information Platforms Licensing Command Mode All platforms Base operating system Config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide crypto-local isakmp certificate-group | 223...
Page 224 Command History This command was introduced in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Config mode on master and local controllers 224 | crypto-local isakmp dpd Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 225 ArubaOS 3.4 The fqdn and fqdn-any parameters were introduced. Command Information Platforms Licensing Command Mode All platforms Base operating system Config mode on master and local controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide crypto-local isakmp key | 225...
Page 226 Command History This command was introduced in ArubaOS 3.2. Command Information Platforms Licensing Command Mode All platforms Base operating system Config mode on master and local controllers 226 | crypto-local isakmp permit-invalid-cert Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 227 Command History This command was introduced in ArubaOS 6.1. Command Information Platforms Licensing Command Mode All platforms Base operating system Config mode on master and local controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide crypto-local isakmp sa-cleanup | 227...
Page 228 CA. You can use the WebUI to generate a Certificate Signing Request (CSR) to submit to a CA and then import the signed certificate received from the CA into the controller. For more information, see “Managing Certificates” in the Dell PowerConnect W- Series ArubaOS User Guide .
Page 229 Command History This command was introduced in ArubaOS 3.2. Command Information Platforms Licensing Command Mode All platforms Base operating system Config mode on master and local controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide crypto-local isakmp xauth | 229...
Page 230 You can import a server certificate in either PKCS12 or x509 PEM format; the certificate is stored in x509 PEM DES encrypted format on the controller. 230 | crypto-local pki Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 231: Related Commands
Certificate Status Protocol (OCSP) or traditional certificate validation using the Certificate Revocation List (CRL) client. Refer to the Certificate Revocation chapter in the Dell PowerConnect W-Series ArubaOS 6.2 User Guide for more information on how to configure this feature using both the WebUI and CLI.
Page 232 The following parameters were introduced: Intermediate CA OCSPResponderCert OCSPSignerCert global-ocsp-signer-cert service-ocsp-responder Command Information Platforms Licensing Command Mode All platforms Base operating system Config mode on master or local controllers 232 | crypto-local pki Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 233 CA. CRL- CRL is used for the revocation check method. OCSP- OCSP is used for the revocation check method. You can configure one fallback method. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide crypto-local pki rcp | 233...
Page 234 Protocol (OCSP) or traditional certificate validation using the Certificate Revocation List (CRL) client. Refer to the Certificate Revocation chapter in the Dell PowerConnect W-Series ArubaOS 6.2 User Guide for more information on how to configure this feature using both the WebUI and CLI.
Page 235 (host)(config) #crypto map global-map 2 ipsec-isakmp dynamic dynamic_map_2 Command History This command was introduced in ArubaOS 3.0 Command Information Platforms Licensing Command Mode All platforms Base operating system Config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide crypto map global-map | 235...
Page 236 The following command configures a CSR for a user with the email address jdoe@example.com . (host)(config) #crypto pki csr key 1024 common_name www.example.lcom country US state_or_ province ca city Sunnyvale organization engineering unit pubs email jdoe@example.com 236 | crypto pki Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 237 The ec curve-name parameter was introduced to support certificate signing requests using an elliptic-curve (EC) key Command Information Platforms Licensing Command Mode All platforms Base operating system Enable mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide crypto pki | 237...
Page 238 The following command installs a server certificate in DER format. (host)(config) #crypto pki-import der ServerCert cert_20 Command History Release Modification ArubaOS 3.0 Command introduced. ArubaOS 6.1 The CRL, IntermediateCA, OCSPResponderCert, OCSPSignerCert parameters were added. 238 | crypto pki-import Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 239 Command Information Platforms Licensing Command Mode All platforms Base operating system Enable mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide crypto pki-import | 239...
Page 240 (host) (config) #database synchronize rf-plan-data Command History This command was introduced in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable and Config modes on master controllers 240 | database synchronize Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 241 The following command deletes all RSA signature entries from flash: (host) #delete ssh-known-hosts Command History This command was introduced in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide delete | 241...
Page 242 ArubaOS 3.0 Replaced with netdestination command. Command Information Availability License Command Mode Can be used only on the master Requires the PEF NG Config mode on master controllers controller. license 242 | destination Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 243 16283 Nov 9 12:25 default.cfg -rw-r--r-- 1 root root 22927 Oct 25 12:21 default.cfg.2006-10-25_20-21-38 -rw-r--r-- 2 root root 19869 Nov 9 12:20 default.cfg.2006-11-09_12-20-22 Command History Introduced in ArubaOS 1.0 Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide dir | 243...
Page 244 Command Information Platform License Command Mode Available on all platforms Available in the base operating system Enable and Config modes on local or master controllers 244 | dir Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 245 Command History This command was introduced in ArubaOS 3.0 Command Information License Command Mode Platform Available on all platforms Available in the base operating system Enable mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide dynamic-ip | 245...
Page 246: Eject Usb
Command introduced in ArubaOS 6.2 Command Information Platform License Command Mode Available on all platforms Available in the base operating system User mode on master or local controllers in enable mode. 246 | eject usb Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 247 If you lose or forget the enable mode password, resetting the default admin user password also resets the enable mode password to “enable”. See the Dell PowerConnect W-Series ArubaOS User Guide for more information about resetting the admin and enable mode passwords.
Page 248 Modification ArubaOS 6.0 Command introduced Command Information Platform License Command Mode Available on all platforms Available in the base operating system Config mode on master or local controllers 248 | enable bypass Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 249: Enable Secret
Updated with restriction of the secret phase Command Informatio Platform License Command Mode Available on all platforms Available in the base operating system Config mode on master or local controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide enable secret | 249...
Page 250 Command History Introduced in ArubaOS 3.0 Command Information Platform License Command Mode Available on all platforms Available in the base operating system Enable mode on master or local controllers 250 | encrypt Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 251 Command History Introduced in ArubaOS 2.5 Command Information Platform License Command Mode Available on all platforms Requires the PEFNG license Config mode on master or local controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide esi group | 251...
Page 252 Command History Introduced in ArubaOS 3.1. Command Information Platform License Command Mode Available on all platforms Requires the PEFNG license Config mode on master or local controllers 252 | esi parser domain Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 253 Condition: The pattern that uniquely identifies the syslog message type. User: The username identifier. It can be in the form of a name, MAC address, or IP address. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide esi parser rule | 253...
Page 254 For more details on the character-matching operators, repetition operators, and expression anchors used to defined the search or match target, refer to the External Services Interface chapter in the Dell PowerConnect W-Series ArubaOS 6.2 User Guide . Use the command to show ESI parser rule information.
Page 255 Command History Introduced in ArubaOS 3.1 Command Information Platform License Command Mode Available on all platforms. Requires the PEFNG license Config mode on master and local controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide esi parser rule | 255...
Page 256 The following command tests against a file named test.log, which contains several syslog messages. esi parser rule-test file test.log < Sep 26 18:30:02 log_id=0100030101 type=virus subtype=infected src=1.2.3.4 > ========== Condition: Matched with rule "forti_rule" User: ipaddr = 1.2.3.4 ========== < Oct 18 10:43:40 cli[627]: PAPI_Send: To: 7f000001:8372 Type:0x4 Timed out. > ========== Condition: No matching rule condition found ========== < Oct 18 10:05:32 mobileip[499]: <500300> <DBUG> |mobileip| Station 00:40:96:a6:a1:a4, 10.0.100.103: DHCP FSM received event: RECEIVE_BOOTP_REPLY current: PROXY_DHCP_NO_PROXY, next: PROXY_DHCP_NO_PROXY > ========== Condition: No matching rule condition found 256 | esi parser rule-test Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 257 Command History Introduced in ArubaOS 3.1 Command Information Platform License Command Mode Available on all platforms Requires the PEFNG license Config mode on master and local controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide esi parser rule-test | 257...
Page 258 Command History Introduced in ArubaOS 2.5 Command Information Platform License Command Mode Available on all platforms Requires the PEFNG license Config mode on master and local controllers 258 | esi ping Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 259 ESI server information. show esi server Example The following command specifies the ESI server attributes. (host) (config) #esi server forti_1 mode route trusted-ip-addr 10.168.172.3 untrusted-ip-addr 10.168.171.3 Command History Introduced in ArubaOS 2.5. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide esi server | 259...
Page 260 Command Information Platform License Command Mode Available on all platforms Requires the PEFNG license Config mode on master and local controllers 260 | esi server Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 261 Introduced in ArubaOS 3.0 Command Information Platform License Command Mode Available on all platforms Available in the base Available in the following command modes: operating system User Enable Config Config sub-modes Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide exit | 261...
Page 262 Command History This command was introduced in ArubaOS 3.0. Command Information Platform License Command Mode Available on all platforms Available in the base operating Enable mode on master controllers. system 262 | export Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 263 "firewall cp" on page 268 cp-bandwidth-contract "firewall cp-bandwidth-contract" on page 270 deny-inter-user-bridging Prevents the forwarding of Layer2 traffic between — disabled wired or wireless users. You can configure user role Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide firewall | 263...
Page 264 You can enable this option if there are no mobile clients on the network. enforce-tcp-sequence Enforces the TCP sequence numbers for all packets. — disabled 264 | firewall Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 265 You can configure the following Ethertype to be mirrored with the Ethertype ACL mirror option. See "ip access-list eth" on page 338. IP flows to be mirrored with the session ACL Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide firewall | 265...
Page 266: Related Commands
The following command disallows forwarding of non-IP frames between users: firewall deny-inter-user-bridging Related Commands (host) (config) #show firewall Command History Release Modification ArubaOS 3.0 Command introduced. ArubaOS 3.2 The wmm-voip-content-enforcement parameter was introduced. 266 | firewall Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 267 License Command Mode Platform Available on all platforms Base operating system Config mode on master controllers except the public-access and voip- wmm-voip-content- enforcement parameters which require the PEFNG license. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide firewall | 267...
Page 268 Specifies the Telnet protocol. — — telnet Specifies the Trivial File Transfer Protocol. — — tftp Specify the name of a bandwidth contract defined via — — bandwidth-contract <name> cp-bandwidth-contract command. 268 | firewall cp Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 269 The ftp, http, https, icmp, snmp, ssh, telnet and tftp parameters were added. Command Information Platform License Command Mode Available on all platforms Base operating system, except for noted Config mode on master parameters controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide firewall cp | 269...
Page 270 (host) (config) #show firewall Command History Introduced in ArubaOS 3.4 Command Information Platform License Command Mode Available on all platforms This command requires the PEFNG license Config mode on master controllers 270 | firewall cp-bandwidth-contract Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 271 This command is introduced in ArubaOS 6.2. Command Information Platforms Licensing Command Mode W-3200, W-3400, W-3600, W- This command requires the PEFNG Config mode on master or local controller 6000M3, and W-7200 series license controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide firewall-visibility | 271...
Page 272 Disable the gateway health check. Usage Guidelines The gateway health check feature can only be enabled by Dell Technical Support. This command disables the gateway health check, and should only be issued under the guidance of the support staff. Related Commands...
Page 273 (host) (Guest-access Email Profile) # (host) (Guest-access Email Profile) #smtp-port 25 (host) (Guest-access Email Profile) #smtp-server 1.1.1.1 Related Commands (host) #show guest-access-email (host) #local-userdb-guest add (host) #local-userdb-guest modify (host) #show local-userdb-guest Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide guest-access-email | 273...
Page 274 Modification ArubaOS 3.4 Introduced for the first time. Command Information Platform License Command Mode Available on all platforms Available in the base operating system. Config mode on master controllers. 274 | guest-access-email Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 275 Command History Introduced in ArubaOS 3.0 Command Information Platform License Command Mode Available on all platforms Available in the base operating system. Enable mode on master and local controllers. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide halt | 275...
Page 276 Available in ArubaOS 3.0 Command Information Platform License Command Mode Available on all platforms Available in the base operating Available in the following command modes: system User Enable Config 276 | help Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 277 Command History Introduced in ArubaOS 1.0 Command Information Platform License Command Mode Available on all platforms Available in the base operating system Config mode on master and local controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide hostname | 277...
Page 278 AP classification rule configuration is performed only on a master controller. If AMP is enabled via the mobility- manager command, then processing of the AP classification rules is disabled on the master controller. A rule is 278 | ids ap-classification-rule change Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 279 Command History Release Modification ArubaOS 6.0 Command introduced Command Information Platforms Licensing Command Mode Available on all platforms Requires the RFprotect license Config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide ids ap-classification-rule change | 279...
Page 280 (host) (IDS Active AP Rules Profile) #rule-name rule2 Command History Release Modification ArubaOS 6.0 Command introduced Command Information Platforms Licensing Command Mode Available on all platforms Requires the RFprotect license Config mode on master controllers 280 | ids ap-rule-matching Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 281 <number> disconnect-deauth-disassoc-threshold disconnect-sta-assoc-resp-threshold disconnect-sta-quiet-time <seconds> eap-rate-quiet-time <seconds> eap-rate-threshold <number> eap-rate-time-interval <seconds> fata-jack-quiet-time invalid-address-combination-quiet-time malformed-association-request-quiet-time malformed-auth-frame-quiet-time malformed-htie-quiet-time malformed-large-duration-quiet-time no ... omerta-quiet-time omerta-threshold overflow-eapol-key-quiet-time overflow-ie-quiet-time Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide ids dos-profile | 281...
Page 282 Time to wait, in seconds, after detecting a 60-360000 client-flood-quiet-time client flood before continuing the check. seconds seconds Threshold for the number of spurious clients 0-100000 client-flood-threshold 282 | ids dos-profile Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 283 Enables or disables detection of 802.11n 40 true false detect-ht-40mhz-intolerance MHz intolerance setting, which controls false whether stations and APs advertising 40 MHz intolerance will be reported. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide ids dos-profile | 283...
Page 284 After an EAP rate anomaly alarm has been 60-360000 eap-rate-quiet-time triggered, the time, in seconds, that must seconds elapse before another identical alarm may be triggered. Number of EAP handshakes that must be 0-100000 eap-rate-threshold 284 | ids dos-profile Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 285 Power Save DoS check to be done. Time to wait, in seconds, after detecting a 60-360000 power-save-dos-quiet-time Power Save DoS attack after which the seconds seconds Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide ids dos-profile | 285...
Page 286 (host) (IDS Denial Of Service Profile "floor2") detect-ap-flood Command History Release Modification ArubaOS 3.0 Command Introduced. ArubaOS 3.3 Updated with support for high-throughput IEEE 802.11n standard. ArubaOS 3.4 detect-disconnect-sta and disconnect-sta-quiet-time parameters deprecated. 286 | ids dos-profile Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 287 Deprecated Predefined Profiles Deprecated DOS profile: ids-dos-disabled ids-dos-low-setting ids-dos-medium-setting ids-dos-high-setting Command Information Platform License Command Mode Available on all platforms Requires the RFprotect license Config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide ids dos-profile | 287...
Page 288 Time, in seconds, after which ap-inactivity-timeout sec- an AP is aged out. 36000 sec- onds onds Ageout time, in seconds, ap-max-unseen-timeout sec- since AP was last seen. 36000 sec- onds onds 288 | ids general-profile Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 289 36000- sec- a station is aged out. onds sec- onds Ageout time, in seconds, sta-max-unseen-timeout sec- since station was last seen. 36000 sec- onds Minimum is 5. onds Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide ids general-profile | 289...
Page 290 Wireless containment by tarpit of non-valid clients wireless-containment-debug Enable/disable debug of true false containment from the false 290 | ids general-profile Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 291 Deprecated predefined profiles and added numerous General profile options Deprecated Predefined Profiles Deprecated General profiles: ids-general-disabled ids-general-high-setting Command Information Platform License Command Mode Available on all platforms Requires the RFprotect license. Config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide ids general-profile | 291...
Page 292 AP attempting to bypass detection, or a honeypot attack. Enable/disable AP Spoofing detection — enable detect-ap-spoofing detect-beacon-wrong-channel Enable/disable detection of beacons advertising — disable 292 | ids impersonation-profile Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 293 Deprecated predefined profiles and added numerous Impersonation profile options Deprecated Predefined Profiles IDS Impersonation profile: ids-impersonation-disabled ids-impersonation-high-setting Command Information Platform License Command Mode Available on all platforms Requires the RFprotect license Config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide ids impersonation-profile | 293...
Page 294 (host) (IDS Management Profile) #event-correlation logs-and-traps Command History Release Modification ArubaOS 6.0 Command introduced Command Information Platforms Licensing Command Mode Available on all platforms Requires the RFprotect license Config mode on master controllers 294 | ids management-profile Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 295 AP (with the ap-name command). Example The following command defines a set of IDS profiles: (host) (config) #ids profile floor2 (host) (IDS Profile "floor2") #dos-profile dos1 general-profile general1 impersonation-profile mitm1 signature-matching-profile sig1 Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide ids profile | 295...
Page 296 Deprecated Profile for levels: disabled, high, medium, and low ids-disabled ids-high-setting ids-medium-setting ids-low-setting Command Information Platform License Command Mode Available on all platforms Requires the RFprotect license Config mode on master controllers. 296 | ids profile Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 297 A profile of this type is attached to each of the following 802.11 frame types in the IDS denial of service profile: Association frames Disassociation frames Deauthentication frames Probe Request frames Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide ids rate-thresholds-profile | 297...
Page 298 Deprecated Predefined Profiles Deprecated the predefined profile with probe-request-response-threshold. Command Information Platform License Command Mode Available on all platforms Requires the RFprotect license Config mode on master controllers 298 | ids rate-thresholds-profile Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 299 (host) (IDS Signature Matching Profile "LobbyEast") #signature Null-Probe-Response Command History Version Modification ArubaOS 3.0 Command Introduced ArubaOS 6.0 Deprecated predefined profiles Deprecated Predefined Profiles Deprecated Signature Matching profile: factory-default-signatures Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide ids signature-matching-profile | 299...
Page 300 Command Information Platform License Command Mode Available on all platforms Requires the RFprotect license Config mode on master controllers 300 | ids signature-matching-profile Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 301 Frame type is probe request Frame type is probe response probe-response For beacon, probe-request, and probe-response frame types, specify the — ssid SSID as either a string or hex pattern. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide ids signature-profile | 301...
Page 302 Netstumbler Version 3.3.0x payload offset=3 pattern=0x00601d payload offset=12 pattern=0x000102 Null-Probe-Response frame-type probe-response ssid length = 0 Command History Version Modification ArubaOS 3.0 Command Introduced 302 | ids signature-profile Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 303 Command Information Platform License Command Mode Available on all platforms Requires the RFprotect license Config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide ids signature-profile | 303...
Page 304 <level> suspect-rogue-containment unencrypted-valid-client-quiet-time valid-and-protected-ssid <ssid> valid-oui <oui> valid-wired-mac <macaddr> wireless-bridge-quiet-time <seconds> wireless-hosted-network-quiet-time Description This command configures detection of unauthorized devices, as well as rogue AP detection and containment. 304 | ids unauthorized-device-profile Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 305 List of valid 802.11b/g channels that third-party APs 1-14 cfg-valid-11g-channel are allowed to use. Enable/disable rogue AP classification. A rogue AP — true classification is one that is unauthorized and plugged into the Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide ids unauthorized-device-profile | 305...
Page 306 Enable/disable detection of misassociation between — enable detect-valid-client-m a valid client and an unsafe AP. This setting can isassociation detect the following misassociation types: MisassociationToRogueAP MisassociationToExternalAP MisassociationToHoneypotAP MisassociationToAdhocAP MisassociationToHostedAP 306 | ids unauthorized-device-profile Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 307 Enables use of SSID by valid APs only. — false protect-ssid When enabled (true), does not allow valid stations — false protect-valid-sta to connect to a non-valid AP. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide ids unauthorized-device-profile | 307...
Page 308 APs. Time to wait, in seconds, after detecting an unencrypted-valid-client- unencrypted valid client after which the check can 360000 seconds quiet-time sec- be resumed. 308 | ids unauthorized-device-profile Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 309 Added the detect-valid-ssid-misuse parameter to internally generate a list of valid SSIDs to use in addition to the user configured list of Valid and Protected SSIDs. ArubaOS 6.2 Added the following parameters Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide ids unauthorized-device-profile | 309...
Page 310 (ageout) from the database. interval <adhoc-ap-ageout- interval> Time, in minutes, that an AP remains unseen by any 30 minutes ap-ageout-interval probes before it is deleted from the database. <ap-ageout-interval> 310 | ids wms-general-profile Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 311: Vlan Trunking
Dell AP, enable the parameter learned-system-wired-mac. When this is enabled, ArubaOS is able to classify rogues on all the VLANs that belong to the Dellcontroller, as long as Dell APs can see the rogues in the air. If there are VLANs in the network residing on a third party controller and if those VLANs are trunked to a port on the Dellcontroller, enabling this feature will allow detection of rogues on those VLANs as well.
Page 312 Command History Release Modification ArubaOS 3.0 Command introduced ArubaOS 6.1 Added parameter learned-system-wired-mac Command Information Platforms Licensing Command Mode All platforms Base operating system Config mode on master controllers 312 | ids wms-general-profile Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 313: Interface Cellular
List the Access groups configured on the cellular interface group Command History Release Modification ArubaOS 5.0 Command introduced Command Information Platforms Licensing Command Mode W-600 series Base operating system Configuration Mode (config-cell) Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide Interface cellular | 313...
Page 314 VLAN associated with this port. Enable tunneled node capability on the interface. — disabled tunneled-node-port Negates any configured parameter. — — Enables Power-over-Ethernet (PoE) on the interface. — enabled 314 | interface fastethernet | gigabitethernet Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 315 APs, public areas, or other networks to which access controls should be applied. When Dell APs are attached directly to the controller, set the port to be trusted. Sets the supplied range of VLANs as trusted. All remaining 1-4094 —...
Page 316: Related Commands
(host) (config-range)# ip access-group (host) (config-range) # ip access-group test session vlan 2 Related Commands (host) #show interface {fastethernet|gigabitethernet} <slot>/<port> (host) #show datapath port vlan-table <slot>/<port> 316 | interface fastethernet | gigabitethernet Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 317 This command is available in the Config mode on master and local controllers base operating system. The ip access-group parameter requires the PEFNG license. The xsec parameter requires the xSec license. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide interface fastethernet | gigabitethernet | 317...
Page 318: Interface Loopback
The parameter ipv6 address was added. Command Information Platforms Licensing Command Mode All platforms This command is available in the Config mode on master and local controllers base operating system 318 | interface loopback Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 319 Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide interface loopback | 319...
Page 320: Interface Port-Channel
Sets switching mode parameters for the interface. — — Sets the interface as an access port for the specified VLAN. The — — access vlan interface carries traffic only for the specified VLAN. 320 | interface port-channel Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 321 APs, public areas, or other networks to which access controls should be applied. When Dell APs are attached directly to the controller, set the port to be trusted. Sets the supplied range of VLANs as trusted. All remaining become 1-4094 —...
Page 322 This command creates a VoIP profile that can be applied to any interface or an interface group. Syntax Parameter Description Range Default Name of the VoIP profile. 1-32 char- — <profile-name> acters; cannot begin with a numeric 322 | interface-profile voip-profile Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 323 This command was introduced in ArubaOS Release Modification ArubaOS 6.2 Command introduced. Command Information Platforms Licensing Command Mode All platforms Base operating system Config mode on master and local controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide interface-profile voip-profile | 323...
Page 324: Interface Range
(favorable for forwarding traffic) than does a higher setting. This is useful if ports may contend for root position if they are connected to an identical bridge. 324 | interface range Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 325 Trusted ports and VLANs are typically connected to internal controlled networks, while untrusted ports connect to third- party APs, public areas, or other networks to which access controls should be applied. When Dell APs are attached directly to the controller, set the port to be trusted. vlan <word>...
Page 326 The trusted VLAN and ip access-group session vlan parameters were introduced. ArubaOS 3.4.1 The trusted vlan <word> parameter was added. Command Information Platforms Licensing Command Mode All platforms Base operating system Config mode on master and local controllers 326 | interface range Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 327: Interface Tunnel
APs, public areas, or other networks to which access controls should be applied. When Dell APs are attached directly to the controller, set the port to be trusted. Configures tunneling. —...
Page 328 Usage Guidelines You can configure a GRE tunnel between an Dell controller and another GRE-capable device. Layer-3 GRE tunnel type is the default (tunnel mode gre ip). You can direct traffic into the tunnel using a static route (specify the tunnel as the next hop for a static route) or a session-based access control list (ACL).
Page 329 Command Information Platforms Licensing Command Mode All platforms Base operating system Config mode on master and local controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide interface tunnel | 329...
Page 330: Interface Vlan
<ipaddr> <netmask> dhcp-client: use DHCP to obtain the IP address internal: IP address allocated from the Remote Node Profile. pppoe: use PPPoE to obtain the IP address 330 | interface vlan Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 331 RA lifetime managed-config-flag—Enables hosts to use DHCP server for stateful address autoconfiguration mtu—Configures maximum transmission unit for RA other-config-flag—Enables hosts to use DHCP server for other non-address stateful autoconfiguration Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide interface vlan | 331...
Page 332 The following command configures a VLAN interface: (host) (config) #interface vlan 16 ip address 10.26.1.1 255.255.255.0 ip helper-address 10.4.1.22 Command History This command was introduced in ArubaOS 3.0 332 | interface vlan Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 333 The nd parameter for configuring neighbor discovery and router advertizement options was introduced. Command Information Platforms Licensing Command Mode All platforms Base operating system Config mode on master and local controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide interface vlan | 333...
Page 334 0 - 3,600,000 retransmit-time <value> msec. Usage Guidelines You can use this command to configure the IPv6 link local address and the global unicast address for this interface. 334 | interface vlan ipv6 address Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 335 The nd parameter for configuring neighbor discovery and router advertisement options was introduced. Command Information Platforms Licensing Command Mode All platforms Base operating system Config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide interface vlan ipv6 address | 335...
Page 336 This release of ArubaOS supports version 1 of the Multicast Listener Discovery (MLD) protocol (MLDv1). MLDv1, defined in RFC 2710, is derived from version 2 of the IPv4 Internet Group Management Protocol (IGMPv2) 336 | interface vlan ip igmp proxy Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 337 Command History This command was introduced in ArubaOS 3.4 Command Information Platforms Licensing Command Mode All platforms Base operating system Config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide interface vlan ip igmp proxy | 337...
Page 338 The following command configures an Ethertype ACL: (host) (config) #ip access-list eth 200 deny 809b Command History Release Modification ArubaOS 3.0 Command introduced ArubaOS 3.3 The mirror parameter was introduced. 338 | ip access-list eth Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 339 Command Information Platform License Command Mode Available on all platforms Requires the PEFNG license. Config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide ip access-list eth | 339...
Page 340 (host) (config) #ipv6 cp-redirect-address Command History Introduced in ArubaOS 6.1 Command Information Platform License Command Mode Available on all platforms Available in the base operating Config mode on master controllers system 340 | ipv6 cp-redirect-address Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 341: Ipv6 Default-Gateway
(host) (config) #ipv6 default-gateway 2cce:205:160:100::fe 1 Command History Introduced in ArubaOS 6.1 Command Information Platform License Command Mode Available on all platforms Available in the base operating Config mode on master controllers system Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide ipv6 default-gateway | 341...
Page 342: Ipv6 Enable
This command was introduced in ArubaOS 6.0. Command Information Platform License Command Mode Available on all platforms Available in the base operating system Config mode on master controllers 342 | ipv6 enable Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 343: Ipv6 Firewall
Appletalk or IPX traffic from being forwarded. When enabled, all IP fragments are dropped. You should not — disabled drop-ip-frag enable this option unless instructed to do so by an Dell ments representative. Enables logging of every packet if logging is enabled for the —...
Page 344 — disabled prohibit-rst-re received from either direction. You should not enable this play option unless instructed to do so by an Dell representative. Time, in seconds, that a non-TCP session can be idle before it 16-259 session-idle- timeout is removed from the session table. You should not modify this seconds option unless instructed to do so by an Dell representative.
Page 345: Ipv6 Mld
(host) (config-mld) # query-interval 200 Command History Introduced in ArubaOS 6.1 Command Information Platform License Command Mode Available on all platforms Available in the base operating Config mode on master controllers system Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide ipv6 mld | 345...
Page 346 346 | ipv6 mld Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 347: Ipv6 Neighbor
(host) (config) #ipv6 neighbor 2cce:205:160:100::fe vlan 1 00:0b:86:61:13:28 Command History Introduced in ArubaOS 6.1 Command Information Platform License Command Mode Available on all platforms Available in the base operating Config mode on master controllers system Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide ipv6 neighbor | 347...
Page 348: Ipv6 Route
(host) (config) #ipv6 route 2cce:205:160:100::fe/<64> 2cce:205:160:100::ff 1 Command History Introduced in ArubaOS 6.1 Command Information Platform License Command Mode Available on all platforms Available in the base operating Config mode on master controllers system 348 | ipv6 route Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 349: Ip Access-List Extended
Internet Gateway Message Protocol tcp: Transmission Control Protocol udp: User Datagram Protocol Source, which can be one of the following: — <source> Source address (IPv4 or IPv6) and wildcard Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide ip access-list extended | 349...
Page 350 Command History This command was available in ArubaOS 3.0. Command Information Platform License Command Mode Available on all platforms Requires the PEFNG license Config mode on master controllers 350 | ip access-list extended Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 351: Ip Access-List Mac
The following command configures a MAC ACL: (host) (config) #ip access-list mac 700 deny 11:11:11:00:00:00 Command History Release Modification ArubaOS 3.0 Command introduced ArubaOS 3.3 The mirror parameter was introduced. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide ip access-list mac | 351...
Page 352 Command Information Platform License Command Mode Available on all platforms Requires the PEFNG license Config mode 352 | ip access-list mac Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 353: Ip Access-List Session
Specify the location to which packets are redirected, which can be one of the following: Datapath destination ID (0-65535). esi-group: Specify the ESI server group configured with the esi group command. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide ip access-list session | 353...
Page 354 (host) (config-sess-common)#host 10.12.13.14 any any permit (host) (config-sess-common)#ipv6 host 11:12:11:11::2 any any permit The following example displays information for an ACL. (host) (config-sess-common)#show ip access-list common ip access-list session common common 354 | ip access-list session Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 355 11:12:11:11::2 permit Command History Introduced in ArubaOS 3.0 Command Information Platform License Command Mode Available on all platforms Requires the PEFNG license Config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide ip access-list session | 355...
Page 356: Ip Access-List Standard
10.1.1.244 Command History Introduced in ArubaOS 3.0 Command Information Platform License Command Mode Available on all platforms Requires the PEFNG license Config mode on master controllers 356 | ip access-list standard Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 357 (host) (config) #ip cp-redirect-address Command History Introduced in ArubaOS 3.0 Command Information Platform License Command Mode Available on all platforms Available in the base operating Config mode on master controllers system Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide ip cp-redirect-address | 357...
Page 358: Ip Default-Gateway
(host) (config) #ip default-gateway 10.1.1.1 Command History Introduced in ArubaOS 3.0 Command Information Platform License Command Mode Available on all platforms Available in the base operating system Config mode on master controllers 358 | ip default-gateway Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 359: Ip Dhcp Excluded-Address
192.168.1.1 192.168.1.255 Command History Introduced in ArubaOS 3.0 Command Information Platform License Command Mode Available on all platforms Available in base operating system Config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide ip dhcp excluded-address | 359...
Page 360: Ip Dhcp Pool
Configure the DHCP pool as an IP upsell pool private: Configure the DHCP pool as private public: Configure the DHCP pool as public Send the ArubaAP vendor ID to clients. vendor-class- identifier 360 | ip dhcp pool Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 361 Command History Introduced in ArubaOS 3.0 Command Information Platform License Command Mode Available on all platforms Available in the base operating system Config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide ip dhcp pool | 361...
Page 362: Ip Domain Lookup
This command was available in ArubaOS 3.0. Command Information Platform License Command Mode Available on all platforms Available in the base operating system Config mode on master controllers 362 | ip domain lookup Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 363: Ip Domain-Name
This command was available in ArubaOS 3.0. Command Information Platform License Command Mode Available on all platforms Available in the base operating system Config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide ip domain-name | 363...
Page 364 1-65535 1/4 of the startup-query-interval general queries on startup. seconds query interval Timeout, in seconds, if a version 1 IGM router is 1-65535 version-1-router-present- timeout detected. seconds seconds 364 | ip igmp Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 365 ArubaOS 6.1 Added parameters: max-members-per-group and quick-client-convergence Command Information Platform License Command Mode Available on all platforms Available in the base operating system Config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide ip igmp | 365...
Page 366 This command was available in ArubaOS 3.0. Command Information Platform License Command Mode Available on all platforms Available in the base operating system Config mode on master controllers 366 | ip local Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 367 This command was available in ArubaOS 3.0. Command Information Platform License Command Mode Available on all platforms Available in the base operating system Config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide ip mobile active-domain | 367...
Page 368 (host) (mobility-domain) #ip mobile domain east_building (host) (mobility-domain) #hat 10.11.1.0 255.255.255.0 120 10.11.1.200 description "East building entries" (host) (mobility-domain) #show ip mobile domain east_building Mobility Domains:, 1 domain(s) 368 | ip mobile domain Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 369 ArubaOS 3.4.1 vlan range parameter introduced. Command Information Platform License Command Mode Available on all platforms Available in the base operating system Config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide ip mobile domain | 369...
Page 370 This command was available in ArubaOS 3.0. Command Information Platform License Command Mode Available on all platforms Available in the base operating system Config mode on master controllers 370 | ip mobile foreign-agent Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 371 This command was available in ArubaOS 3.0. Command Information Platform License Command Mode Available on all platforms Available in the base operating system Config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide ip mobile home-agent | 371...
Page 372 This command was available in ArubaOS 3.4. Command Information Platform License Command Mode Available on all platforms Available in the base operating system Config mode on master controllers 372 | ip mobile packet-trace Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 373 This helps to control frequent mobility state changes when the client bounces back and forth on APs before settling down. Enables logging at the notification level for mobile client — enabled log-trail Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide ip mobile proxy | 373...
Page 374 The proxy mobile IP module in a mobility-enabled controller detects when a mobile client has moved to a foreign network and determines the home agent for a roaming client. The proxy mobile IP module performs the following functions: 374 | ip mobile proxy Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 375 The re-home parameter was deprecated as the re-homing functionality is no longer available. Command Information Platform License Command Mode Available on all platforms Available in the base operating system. Config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide ip mobile proxy | 375...
Page 376 This command was available in ArubaOS 3.0. Command Information Platform License Command Mode Available on all platforms Available in the base operating system. Config mode on master controllers 376 | ip mobile revocation Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 377 {host IP address | host MAC address} Description This command configures the capture of association trail for all devices. Command History Version Description ArubaOS 3.0 Command introduced ArubaOS 6.1 Command deprecated Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide ip mobile trail (deprecated) | 377...
Page 378: Ip Name-Server
This command was available in ArubaOS 3.0. Command Information Platform License Command Mode Available on all platforms Available in the base operating system. Config mode on master controllers 378 | ip name-server Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 379 This command was available in ArubaOS 3.0. Command Information Platform License Command Mode Available on all platforms This command requires the PEFNG license. Config mode on master and local controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide ip nat | 379...
Page 380 Usage Guidelines When configuring OSPF over multiple vendors, use this command to ensure that all routers use the same cost. Otherwise, OSPF may route improperly. 380 | ip ospf Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 381: Related Commands
View the OSPF configuration Command History Release Modification ArubaOS 3.4 Command introduced Command Information Platforms Licensing Command Mode All Platforms Base operating system Configuration Interface Mode (config-subif) Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide ip ospf | 381...
Page 382 This command configures the maximum TCP segment size (mss), in bytes, for Point-to-Point Protocol over Ethernet (PPPoE) data. Command History Release Modification ArubaOS 3.0 Command introduced ArubaOS 6.1 Command deprecated 382 | ip pppoe-max-segment-size (deprecated) Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 383 (deprecated) ip pppoe-password <password> Description This command configures the PPP over Ethernet (PPPoE) password. Command History Release Modification ArubaOS 3.0 Command introduced ArubaOS 6.1 Command deprecated Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide ip pppoe-password (deprecated) | 383...
Page 384 (deprecated) ip pppoe-service-name <service_name> Description This command configures the PPP over Ethernet (PPPoE) service name. Command History Release Modification ArubaOS 3.0 Command introduced ArubaOS 6.1 Command deprecated 384 | ip pppoe-service-name (deprecated) Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 385 (deprecated) ip pppoe-username <username> Description This command configures the PPP over Ethernet (PPPoE) username. Command History Release Modification ArubaOS 3.0 Command introduced ArubaOS 6.1 Command deprecated Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide ip pppoe-username (deprecated) | 385...
Page 386 Available on all platforms The ip radius rfc-3576-server udp-port command Config mode on master and local requires the PEFNG license. Other commands controllers are available in the base operating system. 386 | ip radius Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 387 Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide ip radius | 387...
Page 388 This command was available in ArubaOS 3.0. Command Information Platform License Command Mode Available on all platforms Available in the base operating system Config mode on master and local controllers 388 | ip route Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 389 Command History Release Modification ArubaOS 3.4.1 Command introduced Command Information Platform Licensing Command Mode All Platforms Base operating system Configuration Interface Mode (config-if) for Master and Local controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide lacp group | 389...
Page 390: Lacp Port-Priority
Command History Release Modification ArubaOS 3.4.1 Command introduced Command Information Platform Licensing Command Mode All Platforms Base operating system Configuration Interface Mode (config-if) for Master and Local controllers 390 | lacp port-priority Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 391: Lacp System-Priority
View information on a specified port channel interface Command History Release Modification ArubaOS 3.4.1 Command introduced Command Information Platforms Licensing Command Mode All Platforms Base operating system Configuration Mode (config) for Master and Local controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide lacp system-priority | 391...
Page 392: Lacp Timeout
Command History Release Modification ArubaOS 3.4.1 Command introduced Command Information Platforms Licensing Command Mode All Platforms Base operating system Configuration Interface Mode (config-if) for Master and Local controllers 392 | lacp timeout Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 393 You can use the following show command to display the current LCD settings: (host)#show lcd-menu lcd-menu -------- Menu Value ---- ----- menu maintenance upgrade-image partition0 enabled menu maintenance upgrade-image partition1 enabled menu maintenance system-reboot reboot-stack enabled Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide lcd-menu | 393...
Page 394 Disable image upgrade on partition 1 Command History Introduced in ArubaOS 6.2 Command Information Platform License Command Mode W-7200 series controller only. Available in the base operating Config mode on master controllers system 394 | lcd-menu Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 395 Usage Guidelines Obtain an Dell software license certificate from your Dell sales representative or authorized reseller. Use the certificate ID and the system serial number to obtain a software license key which you install in the controller. NOTE: Users that are not very familiar with this procedure may wish to use the License Management page in the WebUI to install and manage licenses on the controller.
Page 396 Mode show local-cert-mac Display the IP, MAC address and certificate configuration of Config mode on master local controllers in a master-local configuration controllers. Command History Introduced in ArubaOS 6.1 396 | local-custom-cert Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 397 The suite-b gcm-128 and suite-b gcm-256 encryption options for IPsec custom Config mode on platforms certificates requires the Advanced Cryptography (ACR) license. All other master controllers parameters are available in the base operating system Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide local-custom-cert | 397...
Page 398 Command History Introduced in ArubaOS 6.1 Command Information Platform License Command Mode Available on all platforms Available in the base operating system Config mode on master controllers 398 | local-factory-cert Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 399 The following command adds a remote AP whitelist entry for an AP with the MAC address 00:16:CF:AF:3E:E1: (host) (config) #local-userdb-ap add mac-address 00:16:CF:AF:3E:E1 ap-group corp12 ap-name AP42 description “Adding new AP to first floor” Command History Modification ArubaOS 3.0 Command introduced Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide local-userdb-ap add | 399...
Page 400 “Supervisor.” You can enter username, full name, department and Email information into the optional fields. 400 | local-userdb-guest add Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 401 Show the parametesr configured using the local- userdb-guest command. show local-userdb Enable and Config modes Show the parameters configured using the local- userdb command. Command History Introduced in ArubaOS 3.4. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide local-userdb-guest add | 401...
Page 402 Platform License Command Mode Available on all platforms Available in the base operating system. The Enable and config modes on master controllers. role parameter requires the PEFNG license. 402 | local-userdb-guest add Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 403 Configures security for the Remote Node master IP Config mode address. remote-node-profile The remote-node-profile command lets you create a Config mode Remote Node profile. show remote-node Shows Remote Node configuration, dhcp instance, Enable and Config mode Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide local-userdb-remote-node | 403...
Page 404 Command History Modification ArubaOS 6.0 Command introduced. Command Information License Command Mode Platform Available on all platforms Available in the base operating system. Enable mode on master controllers. 404 | local-userdb-remote-node Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 405 “Supervisor.” You can enter username, full name, department and Email information into the optional fields. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide local-userdb add | 405...
Page 406 GuestConnect Username: guest4157 Password: cDFD1675 Expiration: 480 minutes Related Commands Command Description Mode show local-userdb Use this command to show the parameters displayed in Enable and Config modes 406 | local-userdb add Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 407 Command Information Platform License Command Mode Available on all platforms Available in the base operating system. The Enable mode on master controllers. role parameter requires the PEFNG license. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide local-userdb add | 407...
Page 408 (host) (config) #localip 0.0.0.0 ipsec gw1234xyz Command History Command introduced in ArubaOS 3.0. Command Information Platform License Command Mode Available on all platforms Available in the base operating system Config mode on master controllers 408 | localip Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 409 View the LACP system ID information show interface port-channel View information on a specified port channel interface Command History Version Modification ArubaOS 3.0 Command introduced. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide local-userdb-ap del | 409...
Page 410 The following command modifies a AP whitelist entry for an AP with the MAC address 00:16:CF:AF:3E:E1: (host) (config) #local-userdb-ap modify mac-address 00:16:CF:AF:3E:E1 description “AP moved to second floor” Command History Modification ArubaOS 3.0 Command introduced. 410 | local-userdb-ap modify Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 411 The example below revokes an A's entry from the remote AP whitelist. (host)(config) #local-userdb-ap revoke mac-addr 00:0b:86:c3:58:38 revoke-comment "removing this AP from the 1st floor" Command History Modification ArubaOS 3.0 Command introduced. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide local-userdb-ap revoke | 411...
Page 412 (host)#local-userdb del username guest4157 Command History Introduced in ArubaOS 3.0. Command Information Platform License Command Mode Available on all platforms Available in the base operating system Enable mode on master controllers. 412 | local-userdb del Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 413 (host)#local-userdb export jan-userdb Command History Introduced in ArubaOS 3.0. Command Information Platform License Command Mode Available on all platforms Available in the base operating system Enable mode on master controllers. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide local-userdb export | 413...
Page 414 Before using this command, you can save the internal database with the local-userdb export command. Command History Introduced in ArubaOS 3.0. Command Information Platform License Command Mode Available on all platforms Available in the base operating system Enable mode on master controllers. 414 | local-userdb fix-database Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 415 Command History Introduced in ArubaOS 3.4. Command Information Platform License Command Mode Available on all platforms Available in the base operating system Enable and config modes on master controllers. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide local-userdb-guest del | 415...
Page 416 Email information into the optional fields. Same as opt-field-1. — — opt-field-2 Same as opt-field-1. — — opt-field-3 Same as opt-field-1. — — opt-field-4 password User’s password 1– 6 — characters 416 | local-userdb-guest modify Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 417 Command History Introduced in ArubaOS 3.4. Command Information Platform License Command Mode Available on all platforms Available in the base operating system Enable and config modes on master controllers. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide local-userdb-guest modify | 417...
Page 418 (host)# local-userdb-guest send-email Laura to-sponsor Command History Introduced in ArubaOS 3.4. Command Information Platform License Command Mode Available on all platforms Available in the base operating system Enable mode on master controllers 418 | local-userdb-guest send-email Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 419 (host)#local-userdb import jan-userdb Command History Introduced in ArubaOS 3.0. Command Information Platform License Command Mode Available on all platforms Available in the base operating system Enable mode on master controllers. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide local-userdb import | 419...
Page 420 (host)(config)#local-userdb maximum-expiration 480 Command History Introduced in ArubaOS 3.0. Command Information Platform License Command Mode Available on all platforms Available in the base operating system Configuration mode on master controllers. 420 | local-userdb maximum-expiration Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 421 Email information into the optional fields. Same as opt-field-1. — — opt-field-2 Same as opt-field-1. — — opt-field-3 Same as opt-field-1. — — opt-field-4 remote-ip IP address assigned to the remote peer. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide local-userdb modify | 421...
Page 422 The guest, sponsor and optional parameters were added. Command Information Platform License Command Mode Available on all platforms Available in the base operating system Enable mode on master controllers. 422 | local-userdb modify Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 423 Usage Guidelines A guest is the person who needs guest access to the company’s Dell wireless network. Email is sent directly to the guest after the guest user is created. When configuring the guest provisioning feature, the guest user is generally created by Guest Provisioning user.
Page 424 (host)(config)#local-userdb send-to-sponsor Command History Introduced in ArubaOS 3.4. Command Information Platform License Command Mode Available on all platforms Available in the base operating system Configuration mode on master controllers. 424 | local-userdb send-to-sponsor Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 425 (host) (config) #location “Building 10, second floor, room 21E” Command History Introduced in ArubaOS 3.0 Command Information Platform License Command Mode Available on all platforms Available in the base operating system Config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide location | 425...
Page 426 (host) (config) #logging 1.1.1.1 user facility local4 Command History Introduced in ArubaOS 6.0 Command Information Platform License Command Mode Available on all platforms Available in the base operating system Config mode on master controllers 426 | logging Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 427: Logging Facility
(host) (config) #logging facility local4 Command History Introduced in ArubaOS 2.5 Command Information Platform License Command Mode Available on all platforms Available in the base operating system Config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide logging facility | 427...
Page 428: Logging Level
User troubleshooting messages. You must specify a MAC address. user-debug Wireless messages. wireless Controller process, which can be one of the following: process AAA logging Anomaly detection AP processes approc User authentication authmgr 428 | logging level Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 429 Wireless management (master controller only) Message subcategory, which depends upon the message category specified. The following lists subcat the subcategories available for each message category: ap-debug: all network: all, dhcp, mobility, packet-dump Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide logging level | 429...
Page 430 Command History Introduced in ArubaOS 2.5 Command Information Platform License Command Mode Available on all platforms Available in the base operating system Config mode on master and local controllers 430 | logging level Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 431 (host) (config) #loginsession timeout 0 Command History This command was available in ArubaOS 3.0 Command Information Platform License Command Mode Available on all platforms Requires the PEFNG license Config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide loginsession | 431...
Page 432 (host) >logout User: Command History This command was available in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system User mode on local or master controllers 432 | logout Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 433: Mac Address Table
Command History Available in ArubaOS 3.0 Command Information Platform License Command Mode Available on all platforms Available in the base operating Config mode on master and local controllers system Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide mac-address-table | 433...
Page 434 100 preempt description Backup-Master tracking master-up-time 30 add 20 no shutdown master-redundancy master-vrrp 22 peer-ip-address 192.168.22.1 ipsec qwerTY012 Command History This command was introduced in ArubaOS 3.0. 434 | master-redundancy master-vrrp Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 435 Command Information Platforms Licensing Command Mode All platforms Base operating system Config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide master-redundancy master-vrrp | 435...
Page 436 Specify one of the following options: gcm-128 Use 128-bit AES-GCM Suite-B encryption gcm-256 Use 256-bit AES-GCM Suite-B encryption Use the factory-installed certificate on the master controller to establish a master-local ipsec-factory-cert 436 | masterip Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 437 The suite-b gcm-128 and suite-b gcm-256 encryption options Available in Config mode for IPsec custom certificates requires the Advanced on local controllers Cryptography (ACR) license. All other parameters are available in the base operating system Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide masterip | 437...
Page 438 If your master controllers use a pre-shared key for authentication, they will create the IPsec tunnel using IKEv1. If your master and local controllers use certificates for authentication, the IPsec tunnel will be created using IKEv2. 438 | master-redundancy peer-ip Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 439 The suite-b gcm-128 and suite-b gcm-256 encryption options for Config mode on IPsec custom certificates requires the Advanced Cryptography (ACR) master controllers license. All other parameters are available in the base operating system Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide master-redundancy peer-ip | 439...
Page 440 (host) (config) #mgmt-server type amp primary-server 192.168.6.2 Command History Modification ArubaOS 3.4 Command introduced. ArubaOS 6.1 The secondary-server parameter was deprecated. Command Information Platforms Licensing Command Mode All platforms Config mode on master controllers 440 | mgmt-server Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 441 Configures certificate authentication of administrative users using the — ssh-pubkey CLI through SSH. Name of the X.509 client certificate for authenticating administrative — client-cert users using SSH. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide mgmt-user | 441...
Page 442 The ssh-pubkey and webui-cacert parameters were introduced. ArubaOS 3.2 The network-operations role was introduced. ArubaOS 3.3 The location-api-mgmt role and localauth-disable parameters were introduced. ArubaOS 3.4 The webui-cacert <certificate name> parameter had additional functionality introduced. 442 | mgmt-user Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 443 Command Information Platforms Licensing Command Mode All platforms Base operating system Config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide mgmt-user | 443...
Page 444 Use the show mobility-manager command to check the current status of the configured MMS servers. Example The following command configures the IP address and SNMP user profile for the MMS server: (host) (config)# mobility-manager 10.2.1.245 user mms-user my-password. 444 | mobility-manager Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 445 Command History This command was introduced in ArubaOS 3.1. Command Information Platforms Licensing Command Mode All platforms Base operating system Config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide mobility-manager | 445...
Page 446 A frame from http://1.0.0.1 would match the first alias entry, (which allows everything except for 1.0.0.0/8) so the frame would be rejected. However, it would then be compared against the second alias, which allows everything except for 2.0.0.0/8, and the frame would be permitted. 446 | netdestination Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 447 Host functionality now only supports IPv4 subnets. ArubaOS 6.2 Name parameter has maximum character length. Command Information Platforms Licensing Command Mode All platforms Requires the Policy Enforcement Config mode on master controllers Firewall license. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide netdestination | 447...
Page 448 2002:0:0:0:0:0:100:0/128) so the frame would be rejected. However, it would then be compared against the second alias, which allows everything except for 2002:0:0:0:0:0:200:0/128, and the frame would be permitted. Example The following command configures an alias for an internal network: (host) (config) #netdestination6 Internal 448 | netdestination6 Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 449 Maximum length allowed for netdestination6 <name> is now 63 characters. ArubaOS 6.2 Command Information Platforms Licensing Command Mode All platforms Requires the Policy Enforcement Config mode on master controllers Firewall license. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide netdestination6 | 449...
Page 450 The following command denies the IPv6 packets matching the specified extended header type in the default EH: (host) (config) #netexthdr default (host) (config-exthdr) #eh authentication deny Related Commands (host) #show netexthdr <alias-name> Command History Release Modification ArubaOS 6.1 Command introduced 450 | netexthdr Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 451 Command Information Platforms Licensing Command Mode All platforms Base operating system. Config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide netexthdr | 451...
Page 452: Net Service
ACLs. Example The following command configures an alias for a network service: (host) (config) #netservice HTTP tcp 80 452 | netservice Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 453 Command introduced. ArubaOS 6.0 The list parameter for defining non-contiguous ports was introduced. Command Information Platforms Licensing Command Mode All platforms Base operating system Config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide netservice | 453...
Page 454 Command History Release Modification ArubaOS 3.4 Command introduced. ArubaOS 6.2 Command deprecated. Command Information Platforms Licensing Command Mode W-600 series Base operating system Config or enable mode 454 | network-printer [deprecated] Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 455 Share Mode Status --------- -------------- ----------- ---------- ---------- --------- ------ Maxtor1TB MxDocs docum p1/documents Read-Write Active Command History Release Modification ArubaOS 3.4 Command introduced. ArubaOS 6.2 Command deprecated. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide network-storage [deprecated] | 455...
Page 456 Command Information Platforms Licensing Command Mode W-600 series Base operating system Enable mode 456 | network-storage [deprecated] Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 457: Ntp Authenticate
(host) (config) #ntp authenticate Command History Release Modification ArubaOS 6.1 Command introduced Command Information Platforms Licensing Command Mode All platforms Base operating system Config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide ntp authenticate | 457...
Page 458: Ntp Authentication-Key
(host) (config) #ntp authentication-key 12345 md5 67890 Command History Release Modification ArubaOS 6.1 Command introduced Command Information Platforms Licensing Command Mode All platforms Base operating system Config mode on master controllers 458 | ntp authentication-key Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 459: Ntp Server
The iburst parameter was introduced ArubaOS 6.1 The key parameter was introduced Command Information Platforms Licensing Command Mode All platforms Base operating system Config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide ntp server | 459...
Page 460: Ntp Trusted-Key
(host) (config) #ntp trusted-key 84956 Command History Release Modification ArubaOS 6.1 Command introduced Command Information Platforms Licensing Command Mode All platforms Base operating system Config mode on master controllers 460 | ntp trusted-key Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 461: Packet Capture
DHCP: sysmsg opcode 90 IKE: UDP port 500 and 4500 Layer 2 Tunneling Protocol (L2TP): UDP port 1701 (host) #packet-capture sysmsg 30,29,90 udp 500,4500,1701,1812,1645 Command History This command was introduced in ArubaOS 2.3. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide packet-capture | 461...
Page 462 Command Information Platforms Licensing Command Mode All platforms Base operating system Enable mode on master controllers 462 | packet-capture Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 463 Use the show packet-capture command to show the current action and the default values. (host) show packet-capture Current Active Packet Capture Actions(current switch) ===================================================== Packet filtering TCP with 2 port(s) enabled: Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide packet-capture-defaults | 463...
Page 464 Packet filtering UDP with 1 port(s) enabled: Command History This command was introduced in ArubaOS 2.3. Command Information Platforms Licensing Command Mode All platforms Base operating system Config mode on master controllers 464 | packet-capture-defaults Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 465 (host) (config) #page 80 Command History This command was introduced in ArubaOS 1.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Config and Enable mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide page | 465...
Page 466 (host) (config) #paging Command History This command was introduced in ArubaOS 1.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Config and Enable mode on master controllers 466 | paging Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 467 (host) #panic list nvram Command History This command was introduced in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide panic | 467...
Page 468 [enhanced-security] no... Description The papi-security command enforces advanced security options and provides an enhanced level of security. WARNING: The best practice is to refrain from modifying these settings unless advised to do so by Dell technical support. Syntax Parameter Description Default The key authenticates the messages between systems.
Page 469: Related Commands
Command History Modification ArubaOS 3.4 Command introduced. ArubaOS 6.2 Command deprecated Command Information Platform License Command Mode Available on all platforms Base operating system Config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide papi-security (deprecated) | 469...
Page 470 {raw-start <ipaddr> <target-ipaddr> <target-port> <format> [bssid <bssid>] [channel <number>] [maxlen <maxlen>]}|{interactive <am-ip> <filter> <target-ipaddr> <target-port> [bssid <bssid>][channel <number>]}|{clear|pause|resume|stop <am-ip> <id> [bssid <bssid>]} Description These commands manage packet capture (PCAP) on Dell air monitors. Syntax Parameter Description Stream raw packets to an external viewer.
Page 471 In the capture window, the time stamp displayed corresponds to the time that the packet is received by the client and is not synchronized with the time on the Dell air monitor.
Page 472 Functionality with 2 new parameters, now subsumed by the ap packet capture command. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable mode on master controllers 472 | pcap (deprecated) Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 473 Syntax Parameter Description Range The controller will periodically contact Dell support once a auto-report week to report any errors or changes to the controller configuration or inventory. If the controller has not reported any errors and its configuration file has not changed, no report will be sent.
Page 474 SMTP server configured on your local network, which then delivers the message to Dell. If your email server requires the sender to be authenticated before message delivery, the controller can connect to the SMTP by supplying the sender’s user name and password.
Page 475 The sample controller output is: Press 'q' to abort. Sending 5, 100-byte ICMPv6 Echos to 2005:d81f:f9f0:1001::14, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 0.309/0.3726/0.463 ms Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide ping | 475...
Page 476 Introduced ipv6 parameter to provide support for IPv6. This command was introduced in ArubaOS 1.0. Command Information Platforms Licensing Command Mode All platforms Base operating system User, Enable, and Config modes on master controllers 476 | ping Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 477 <acl-name> {enable|disable} [trace {cptrace|pktrace} [trace-mask <tmask>]]] Description Enable packet tracing in the datapath. Use this feature only under the supervision of Dell technical support. Syntax Parameter Description <acl-name> Enable packet tracing for the specified access-control list. Enable packet tracing for the ACL.
Page 478 {enable|disable} [trace-mask <tmask>] Description Enable global packet tracing in the datapath. Use this feature only under the supervision of Dell technical support. Syntax Parameter Description Enable packet tracing for the specified access-control list. <acl-name> Enable global packet tracing for the ACL.
Page 479 This command configures a Policer profile to manage the transmission rate of a class of traffic based on user-defined criteria. Command History Release Modification ArubaOS 6.2 Command deprecated. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide policer-profile (deprecated) | 479...
Page 480 (host) (config) #pptp ip local pool pptp-pool1 172.16.18.1 172.16.18.24 Command History This command was introduced in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Config mode on master controllers 480 | pptp ip local pool Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 481: Priority-Map
1/24 priority-map pri1 Command History This command was introduced in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide priority-map | 481...
Page 482: Process Monitor
Chances ---- ----- -------- ------------- --------------- /mswitch/bin/arci-cli-helper PROCESS_RUNNING /mswitch/bin/fpcli PROCESS_RUNNING /mswitch/bin/packet_filter PROCESS_RUNNING /mswitch/bin/certmgr PROCESS_RUNNING /mswitch/bin/dbstart PROCESS_RUNNING /mswitch/bin/cryptoPOST PROCESS_RUNNING /mswitch/bin/sbConsoled PROCESS_RUNNING /mswitch/bin/pubsub PROCESS_RUNNING /mswitch/bin/cfgm PROCESS_RUNNING /mswitch/bin/syslogdwrap PROCESS_RUNNING /mswitch/bin/aaa PROCESS_RUNNING 482 | process monitor Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 483 ArubaOS 3.4 Command introduced ArubaOS 3.4 The process restart command was deprecated. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide process monitor | 483...
Page 484 (It’s a new day!) (config) # Command History This command was introduced in ArubaOS 1.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Config mode on master controllers 484 | prompt Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 485 {all|ap-name <name>|ip-addr <ipaddr>|serial-num <string>| wired-mac <macaddr>} reset-bootinfo {ap-name <name>|ip-addr <ipaddr>|wired-mac <macaddr>} server-ip <ipaddr> sch-mode-radio-0 sch-mode-radio-1 server-name <name> set-ikepsk-by-addr <ip-addr> syslocation <string> uplink-vlan <uplink-vlan> usb-dev <usb-dev> usb-dial <usb-dial> usb-init <usb-init> Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide provision-ap | 485...
Page 486 3g_only: Locks the modem to operate only in 3G. 4g_only: Locks the modem to operate only in 4G. advanced: The RAP controls the cellular network service selection based on an Received Signal Strength Indication (RSSI) threshold- 486 | provision-ap Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 487 IKE preshared key for the AP. — ikepsk Specify the type of installation (indoor or outdoor). The default parameter default installation automatically selects an installation mode based upon the AP model indoor type. outdoor Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide provision-ap | 487...
Page 488 If you use quotes (single or double), you must use the backslash (\) before and after the password PAP username for the AP. pap-user — PPPoE CHAP secret key for the AP. pppoe-chap-secret — 488 | provision-ap Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 489 USB cellular data-card. product> -M <message_ content>" NOTE: You must enclose the entire modeswitch parameter string in quotation marks. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide provision-ap | 489...
Page 490 1. Use the read-bootinfo option to read the current information from the deployed AP you wish to reprovision. 2. Use the show provisioning-ap-list command to see the AP to be provisioned. 3. Use the copy-provisioning-params option to copy the AP’s parameter values to the provisioning-params workspace. 490 | provision-ap Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 491 The following commands change the IP address of the master controller on the AP: (host) (config) #provision-ap read-bootinfo ap-name lab103 show provisioning-ap-list copy-provisioning-params ap-name lab103 master 10.100.102.210 reprovision ap-name lab103 Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide provision-ap | 491...
Page 492 Command Mode All platforms, except for the Base operating system, except for Config mode on master controllers parameters noted in the Syntax table. the parameters noted in the Syntax table. 492 | provision-ap Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 493 Description This command configures a QoS profile to assign TC/DP, DSCP, and 802.1p values to an interface or policer profile. Command History Release Modification ArubaOS 6.2 Command deprecated. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide qos-profile (deprecated) | 493...
Page 494 This example configures an MSSQL server and sets up associated rap-wml table attributes. (host) (config) #rap-wml mssqlserver type mssql ip-addr 10.4.11.11 db-name automatedtestdatabase user sa password sa rap-wml table mssqlserver mactest_undelimited mac timestamp-column time 600 rap-wml table mssqlserver mactest_delimited mac delimiter : timestamp-column time 600 Command History This command was introduced in ArubaOS 2.0. 494 | rap-wml Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 495 Command Information Platforms Licensing Command Mode All platforms Requires the RF Protect license. Config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide rap-wml | 495...
Page 496 This example configures an MSSQL server and sets up associated rap-wml table attributes for that server. (host) (config) # rap-wml mssqlserver type mssql ip-addr 10.4.11.11 db-name automatedtestdatabase user sa password sa rap-wml table mssqlserver mactest_undelimited mac timestamp-column time 600 rap-wml table mssqlserver mactest_delimited mac delimiter : timestamp-column time 600 Command History This commands was introduced in ArubaOS 2.0. 496 | rap-wml table Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 497 Command Information Platforms Licensing Command Mode All platforms Requires the RF Protect license. Config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide rap-wml table | 497...
Page 498 (deprecated) reload-peer-sc Description This command performs a reboot of the W-6000M3 controller module. Command History Version Description ArubaOS 6.1 Command deprecated 498 | reload-peer-sc (deprecated) Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 499 Use this command to reboot the controller if required after making configuration changes or under the guidance of Dell Networks customer support. The reload command powers down the controller, making it unavailable for configuration. After the controller reboots, you can access it via a local console connected to the serial port, or through an SSH, Telnet, or WebUI session.
Page 500 (host) (config) remote-node-local-factory-certs Command History Introduced in ArubaOS 6.1 Command Information Platform License Command Mode Available on all platforms Available in the base operating system Config mode on master controllers 500 | remote-node-local-factory-cert Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 501 (host) (config) remote-node-localip 172.16.0.254 ipsec rhyopevs Command History Introduced in ArubaOS 6.0 Command Information Platform License Command Mode Available on all platforms Available in the base operating system Config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide remote-node-localip | 501...
Page 502 The ipsec-factory-cert parameter was introduced to allow certificate-based authentication of Remote-Node Masters. Command Information Platform License Command Mode Available on all platforms Available in the base operating system Config mode on local Remote Nodes. 502 | remote-node-masterip Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 503: Remote Node Profile
<port>]}|inform queue-length <size>|source|stats|trap enable|disable|{source <ipaddr>} |user <name> [auth-prot {md5|sha} <password>] [priv-prot {AES|DES} <password>] spanning-tree [forward-time <value> | hello-time <value> | max-age <value> | priority <value> | vlan range <WORD>| syscontact <syscontact> syslocation <syslocation> Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide remote-node-profile | 503...
Page 504 NOTE: The VLAN ID mapped using the “interface vlan <id> ip address” command can use the following parameters to define how the controller-ip is derived: dhcp-client: The remote node will use DHCP to obtain IP address 504 | remote-node-profile Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 505 For details on using this command, see page 481. Name of the DHCP pool. remote-node-dhcp-pool <pool_name> Specify whether you are creating a pool of IP addresses for RN VLANs pool-type {vlan <id>}|tunnel Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide remote-node-profile | 505...
Page 506 Use the remote-node-profile command to create a Remote Node profile. You define configuration settings for each Remote Node through a Remote Node profile on the Remote Node-master. The Remote Node-master must be a master controller. 506 | remote-node-profile Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 507: Related Commands
Command Information Platform License Command Mode Available on all platforms Available in the base operating system. Enable and Config modes on master controllers. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide remote-node-profile | 507...
Page 508 (host) (config) #rename test_configuration deployed_configuration Command History This command was introduced in ArubaOS 1.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Eanble and Config modes on master controllers 508 | rename Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 509 The following command restores flash directories from the flashbackup.tar.gz file: (host) #restore flash Command History This command was introduced in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide restore | 509...
Page 510 Scan all channels (all regulatory domains — — rare and rare channels) Scan channels in the APs regulatory — — reg-domain domain Command History Release Modification ArubaOS 6.0 Command introduced 510 | rf am-scan-profile Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 511 Command Information Platforms Licensing Command Mode All Platforms RFProtect Configuration Mode (config) Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide rf am-scan-profile | 511...
Page 512 Usage Guidelines This command can run predefined test profiles for antenna connectivity, link quality, or raw testing. You should only run these commands when directed to do so by an Dell support representative. Command History This command was introduced in ArubaOS 3.0.
Page 513 2.4 GHZ (802.11b/g) frequency bands. None Disallows use of 40 MHz channels. Allows use of 40 MHz channels on the 5 GHZ (802.11a) a-only frequency band only. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide rf arm-profile | 513...
Page 514 AP will move to the new channel. Recommended value is 25. ideal-coverage- The coverage that the AP should try to achieve on its 2-20 514 | rf arm-profile Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 515 Recommended Values: 0-80 -dBm Minimum time in seconds the noise level has to 1-3600 seconds 120 seconds noise-wait-time exceed the Noise Threshold before it triggers a channel change. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide rf arm-profile | 515...
Page 516 Enable WMM on the WLAN’s SSID profile and define a specific DSCP value as a video stream. Next, create a session ACL to tag the video traffic with the that DSCP value. 516 | rf arm-profile Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 517 Parameter Description Range Default Dell’s VoIP Call Admission Control (CAC) prevents any — disabled voip-aware-scan single AP from becoming congested with voice calls. When you enable CAC, you should also enable voip- aware-scan parameter in the ARM profile, so the AP will not attempt to scan a different channel if one of its clients has an active VoIP call.
Page 518 OS. The ps-aware-scan parameter is now disabled by default. ArubaOS Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master controllers 518 | rf arm-profile Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 519 See "rf arm-profile" on page 513. Time, in milliseconds, between successive beacon 60 (minimum) beacon-period transmissions. The beacon advertises the AP’s milliseconds presence, identity, and radio characteristics to Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide rf dot11a-radio-profile | 519...
Page 520 Entering a channel number with a minus (-) sign selects a primary and secondary channel for 40 MHz mode. The number entered becomes the primary channel and the secondary 520 | rf dot11a-radio-profile Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 521 Clients must support CSA in order to track the channel change without experiencing disruption. Number of CSA announcements that are sent 1-16 csa-count before the AP begins transmitting on the new channel. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide rf dot11a-radio-profile | 521...
Page 522 20/40 MHz mode for a 5 GHz frequency band radio: 20MHz mode: 58km 40MHz mode: 27km Note that if you configure a value above the 522 | rf dot11a-radio-profile Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 523 If spectrum load balancing is enabled in a 802.11a radio profile but the spectrum load balancing domain is not defined, ArubaOS uses the ARM feature to calculate RF Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide rf dot11a-radio-profile | 523...
Page 524 If an AP’s client load is at or over a predetermined threshold as compared to its immediate neighbors, or if a neighboring Dell AP on another channel does not have any clients, load balancing will be enabled on that AP. This feature is disabled by default.
Page 525 RX Sensitivity Threshold ARM/WIDS Override ArubaOS 3.4.1 The maximum-distance parameter was introduced. ArubaOS 3.4.2 The beacon-regulate parameter was introduced. ArubaOS 6.0 Support for the following parameters: am-scan-profile cap-reg-eirp slb-mode slb-update-interval Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide rf dot11a-radio-profile | 525...
Page 526 The spectrum-monitoring and slb-threshold parameters were introduced. ArubaOS 6.1.3.2 The cell-size-reduction parameter was introduced. Command Information Platforms Licensing Command Mode All platforms Base operating system Config mode on master controllers 526 | rf dot11a-radio-profile Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 527 1-63 characters. am-scan-profile <profile- Configure an Air Monitor (AM) scanning profile. — — name> Configures Adaptive Radio Management (ARM) — “default” arm-profile feature. See "rf arm-profile" on page 513. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide rf dot11g-radio-profile | 527...
Page 528 Depends on — channel physical layer. The available channels depend on regulatory the regulatory domain (country). Channel number domain configuration options for 20 MHz and 40 MHz modes: 528 | rf dot11g-radio-profile Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 529 AP’s Rx sensitivity threshold (in - dBm). The AP will filter out and ignore weak signals that are below the channel threshold Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide rf dot11g-radio-profile | 529...
Page 530 NOTE: Do not raise the noise immunity feature’s default setting if the "channel-reuse-threshold" on page 521 feature is also enabled. A level-3 to level-5 Noise Immunity setting is not compatible with the Channel Reuse feature. 530 | rf dot11g-radio-profile Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 531 Radio-based load-balancing balances clients across APs If the spectrum load balancing feature is enabled, 1-100% slb-threshold this parameter controls the percentage difference between number of clients on a channel channel Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide rf dot11g-radio-profile | 531...
Page 532 If an AP’s client load is at or over a predetermined threshold as compared to its immediate neighbors, or if a neighboring Dell AP on another channel does not have any clients, load balancing will be enabled on that AP. This feature is disabled by default.
Page 533 The following command configures a primary channel number of 1 and a secondary channel number of 5 for 40 MHz mode of operation for the selected dot11g-radio profile named “sampleg:” rf dot11g-radio-profile sampleg channel <1+> Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide rf dot11g-radio-profile | 533...
Page 534 The spectrum-monitoring and slb-threshold parameters were introduced. ArubaOS 6.1.3.2 The cell-size-reduction parameter was introduced. Command Information Platforms Licensing Command Mode All platforms Base operating system Config mode on master controllers 534 | rf dot11g-radio-profile Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 535 16%. After a frame error rate exceeded condition exists, the 0-100 fer-low-wm condition persists until the frame error rate drops below this value. The recommended value is 8%. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide rf event-thresholds-profile | 535...
Page 536 This profile and many of the detection parameters are disabled (value is 0) by default. Example The following command configures an event threshold profile: (host) (config) #rf event-thresholds-profile et1 536 | rf event-thresholds-profile Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 537 Command History This command was introduced in ArubaOS 3.0 Command Information Platforms Licensing Command Mode All platforms Base operating system Config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide rf event-thresholds-profile | 537...
Page 538 This enables interoperability for legacy or high- throughput stations that cannot decode 802.11n cyclic shift diversity (CSD) data. This feature is disabled by default and should be kept disabled unless necessary. 538 | rf ht-radio-profile Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 539 The single-chain-legacy parameter was renamed to diversity-spreading-workaround. Command Information Platforms Licensing Command Mode All platforms, but operates with Base operating system Config mode on master controllers IEEE 802.11n compliant devices only Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide rf ht-radio-profile | 539...
Page 540 (host) (RF Optimization Profile "Angela1") #rssi-falloff-wait-time 3 (host) (RF Optimization Profile "Angela1") #rssi-check-frequency 2 Command History Version Modification ArubaOS 3.0 Command introduced ArubaOS 3.4 The following parameters were deprecated: ap-lb-max-retries <number> 540 | rf optimization-profile Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 541 The following parameters were deprecated: detect-association-failure detect-interference hole-detection-interval hole-good-rssi-threshold hole-good-sta-ageout hole-idle-sta-ageout hole-poor-rssi-threshold interference-baseline interference-exceed-time interference-threshold Command Information Platforms Licensing Command Mode All platforms Base operating system Config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide rf optimization-profile | 541...
Page 542 25 sec xbox 2.4GHz spectrum monitor radios only. Make a copy of an existing spectrum profile. 600 sec clone <source> Remove a spectrum profile or negate a configured parameter. 542 | rf spectrum-profile Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 543: Related Commands
60 sect (was 10 sect in previous releases) Command Information Platforms Licensing Command Mode All platforms RF Protect license Config mode on master and local controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide rf spectrum-profile | 543...
Page 544 (host) (config) #router mobile Command History Release Modification ArubaOS 3.0 Command introduced Command Information Platforms Licensing Command Mode All platforms Base operating system Config mode on master controllers 544 | router mobile Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 545: Router Ospf
OSPFv2 is a dynamic Interior Gateway routing Protocol (IGP) based on IETF RFC 2328. The ArubaOS implementation of OSPF allows controllers to deploy effectively in a Layer 3 topology. For more detailed information, refer to the OSPF Chapter in the Dell PowerConnect W-Series ArubaOS User Guide . Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 546 Command introduced ArubaOS 6.0 Added the options: area, default-cost, nssa, and default-information originate always Command Information Platforms Licensing Command Mode All Platforms Base operating system Configuration Mode (config) 546 | router ospf Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 547 The DHCP command was introduced in ArubaOS 3.0. The network-storage and print-server options was introduced in ArubaOS 3.4 Command Information Platforms Licensing Command Mode All platforms Base operating system Config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide service | 547...
Page 548 MAC address of the Local Certificate Type of certificate used by the local controller. Cert-Type Custom: User-installed, custom certificate Factory: Factory-installed certificate Name of the Certificate Authority (CA) certificate. CA Cert 548 | show local-cert-mac Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 549 Command History Available in ArubaOS 6.1 Command Information Platforms Licensing Command Mode All platforms Base operating system Config or Enable mode on master or local controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show local-cert-mac | 549...
Page 550 Maximum number of hosts supported by a Remote Node using this pool. Num Hosts Related Commands Command Description Mode remote-node-profile The remote-node-profile command lets you create a Config mode Remote Node profile. 550 | show remote-node-dhcp-pool Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 551 Command History Release Modification ArubaOS 6.0 Command introduced Command Information Platforms Licensing Command Mode All platforms Base operating system Enable mode on master and local controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show remote-node-dhcp-pool | 551...
Page 552 0.0.0.0 endip 0.0.0.0 hosts 1 Related Commands Command Description Mode remote-node-profile The remote-node-profile command lets you create a Config mode Remote Node profile. Command History Release Modification ArubaOS 6.0 Command introduced 552 | show remote-node-profile Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 553 Command Information Platforms Licensing Command Mode All platforms Base operating system Enable mode on master and local controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show remote-node-profile | 553...
Page 554 3 ip address 10.3.29.79 255.255.255.0 interface vlan 2 interface vlan 2 ip address 192.167.1.1 255.255.255.240 uplink wired vlan 4 interface tunnel 1 interface tunnel 1 tunnel destination remote-node-master-ip 554 | show remote-node Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 555 Command History Release Modification ArubaOS 6.0 Command introduced Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or config mode on master and local controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show remote-node | 555...
Page 556 This command was introduced in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master and local controllers 556 | show aaa authentication all Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 557 Captive Portal Authentication Profile "portal1" ------------------------------------------------ Parameter Value --------- ----- Default Role guest Default Guest Role guest Server Group default Redirect Pause 10 sec User Login Enabled Guest Login Disabled Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show aaa authentication captive-portal | 557...
Page 558 CPU utilization threshold applied when directing a captive portal user with the logon page. Maximum number of authentication failures before the user is Max Authentication failures blacklisted. 558 | show aaa authentication captive-portal Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 559 Command History This command was introduced in ArubaOS 3.0. Version Description ArubaOS 3.0 Command introduced ArubaOS 6.1 The sygate-on-demand parameter was deprecated, and the white-list and black-list Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show aaa authentication captive-portal | 559...
Page 560 Authentication Protocol parameter was added, and the Use CHAP parameter was deprecated. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master or local controllers 560 | show aaa authentication captive-portal Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 561 Path and filename for a custom JPEG captive portal background image. This Custom page background option is only available if the controller has a custom login page design theme. image Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show aaa authentication captive-portal customization | 561...
Page 562 This command was introduced in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master or local controllers 562 | show aaa authentication captive-portal cus- Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide tomization...
Page 563 (host) #show aaa authentication dot1x pDot1x 802.1X Authentication Profile "pDot1x" -------------------------------------- Parameter Value --------- ----- Max authentication failures Enforce Machine Authentication Disabled Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show aaa authentication dot1x | 563...
Page 564 Interval, in seconds, between unicast key rotations. Unicast Key Rotation Time Interval Authentication Server Retry Interval Server group retry interval, in seconds. The number of server group retries. Authentication Server Retry Count 564 | show aaa authentication dot1x Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 565 OKC do not send the PMKID in their association request.) If enabled, the controller will use a RADIUS session Use Session Key Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show aaa authentication dot1x | 565...
Page 566 This feature is only applicable for phones that support WPA. Shows if the rekey and reauthentication features for Disable rekey and reauthentication for clients voice-over-WLAN clients has been enabled or on call disabled. 566 | show aaa authentication dot1x Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 567 The Check certificate common name against AAA server, Enforce Suite-b-128 and Enforce Suite-b-192 parameters were introduced. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master or local controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show aaa authentication dot1x | 567...
Page 568: Show Aaa Authentication Mac
(host) #show aaa authentication mac MacProfile1 MAC Authentication Profile "MacProfile1" ---------------------------------------- Parameter Value --------- ----- Delimiter colon Case upperMax Authentication failures 568 | show aaa authentication mac Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 569 This command was introduced in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master or local controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show aaa authentication mac | 569...
Page 570 The output of the show aaa authentication mgmtcommand includes the following parameters Related Commands Command Description Mode aaa authentication mgmt Configure management authentication settings. Config mode 570 | show aaa authentication mgmt Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 571 The Mode parameter in the command output was renamed Enable. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master or local controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show aaa authentication mgmt | 571...
Page 572 [config-entries] Description This command displays configuration settings for 802.1X authentication for clients on non-Dell APs. Syntax Parameter Description Display details for the AP Server configuration list. config-entries Usage Guidelines Issue this command to identify the default role assigned to the 802.1X user group, name of the group of RADIUS servers used to authenticate the 802.1X users, and the 802.1X authentication timeout period, in seconds.
Page 573 This command was introduced in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master or local controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show aaa authentication stateful-dot1x | 573...
Page 574 (host) #show aaa authentication stateful-ntlm default Stateful NTLM Authentication Profile "default" ---------------------------------------------- Parameter Value --------- ----- Default Role guest Server Group default Mode Disabled Timeout 10 sec 574 | show aaa authentication stateful-ntlm Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 575 This command was introduced in ArubaOS 3.4.1. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master or local controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show aaa authentication stateful-ntlm | 575...
Page 576 VIA authentication profile via1. VIA Authentication Profile "via1" --------------------------------- Parameter Value --------- ----- Default Role default-via-role Server Group internal Max Authentication failures 576 | show aaa authentication via auth-profile Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 577 This command was introduced in ArubaOS 5.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master or local controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show aaa authentication via auth-profile | 577...
Page 578 VIA Connection Profile "default" -------------------------------- Parameter Value --------- ----- VIA Servers Client Auto-Login Enabled VIA Authentication Profiles to provision 578 | show aaa authentication via connection-profile Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 579 Default: Enabled This is the list of VIA authentication profiles that will be displayed to users in the VIA VIA Authentication client. Profiles to provision Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show aaa authentication via connection-profile | 579...
Page 580 VIA checks for FIPS compliance during startup. This option is disabled by default. Select this option to automatically connect to a configured WLAN network. Auto-Launch Supplicant 580 | show aaa authentication via connection-profile Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 581 Applicable to VIA client installed in computers running Microsoft Windows operating minimized system. Block traffic until If enabled, this feature will block network access until the VIA VPN connection is established. VPN tunnel is up Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show aaa authentication via connection-profile | 581...
Page 582 This command was introduced in ArubaOS 5.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master or local controllers 582 | show aaa authentication via connection-profile Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 583 Description Mode aaa authentication via web- aaa authentication via web-auth to configure the Config mode auth parameters displayed in the output of this show command. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show aaa authentication via web-auth | 583...
Page 584 This command was introduced in ArubaOS 5.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master or local controllers 584 | show aaa authentication via web-auth Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 585 Default Role Server Group The name of the server group that performs the authentication. Number of times a user attempted to authenticate, but failed. Max Authentication failures Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show aaa authentication vpn | 585...
Page 586 The Check certificate common name against AAA server parameter was introduced. Command Information Platforms Licensing Command Mode All platforms The PEFV license and the base Enable or Config mode on master or local operating system. controllers 586 | show aaa authentication vpn Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 587 This command was introduced in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master or local controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show aaa authentication wired | 587...
Page 588 WISPr Location Name Sunnyvale The following example displays configuration details for the WISPr authentication profile “WISPr1”. (host) #show aaa authentication wispr WISPr1 WISPr Authentication Profile "WISPr1" 588 | show aaa authentication wispr Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 589 Configure WISPr authentication values on your Config mode on master or local controller. controllers. Command History This command was introduced in ArubaOS 3.4.1. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show aaa authentication wispr | 589...
Page 590 Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master or local controllers 590 | show aaa authentication wispr Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 591 Shows whether the Authentication server is enable or disabled. Requests Number of authentication requests received by the server. Command History This command was introduced in ArubaOS 3.0. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show aaa authentication-server all | 591...
Page 592 Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master or local controllers 592 | show aaa authentication-server all Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 593 Mismatch Response Users Expired Unknown Response Timeouts AvgRespTime (ms) Uptime (d:h:m) 4:3:32 SEQ first/last/free 1,255,255 The following data columns appear in the output of this command: Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show aaa authentication-server internal | 593...
Page 594 This command was introduced in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master or local controllers 594 | show aaa authentication-server internal Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 595 Auth Port Base-DN cn=Users,dc=1m,dc=corp,dc=com Filter (objectclass=*) Key Attribute sAMAccountName Timeout 20 sec Mode Enabled Preferred Connection Type ldap-s The output of this command includes the following parameters: Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show aaa authentication-server ldap | 595...
Page 596 This command was introduced in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master or local controllers 596 | show aaa authentication-server ldap Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 597 --------- ----- Host 127.0.0.1 ******** Auth Port 1812 Acct Port 1813 Retransmits Timeout 5 sec NAS ID NAS IP Source Interface Use MD5 Disabled Mode Enabled Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show aaa authentication-server radius | 597...
Page 598 The Source Interface parameter was introduced. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master or local controllers 598 | show aaa authentication-server radius Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 599 Include the <tacacs_server_name> parameter to display additional details for an individual server (host) #show aaa authentication-server tacacs tacacs1 TACACS Server "tacacs1" --------------------- Parameter Value --------- ----- Host 10.1.1.16 ******** TCP Port Retransmits Timeout 20 sec Mode Enabled Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show aaa authentication-server tacacs | 599...
Page 600 ArubaOS 6.0 The Statistics parameter was introduced. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master or local controllers 600 | show aaa authentication-server tacacs Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 601 IP address of the Windows server host Shows whether this server is Enabled or Disabled. Mode Name of the Windows domain to which this server is assigned. Windows Domain Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show aaa authentication-server windows | 601...
Page 602 This command was introduced in ArubaOS 3.4.1. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master or local controllers 602 | show aaa authentication-server windows Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 603 This command was introduced in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master or local controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show aaa bandwidth-contracts | 603...
Page 604 The priority in which the rules are applied. Rules at the top of the list are applied before rules at the bottom. Attribute This is the attribute returned by the authentication server that is examined for Operation 604 | show aaa derivation-rules Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 605 This is the attribute returned by the authentication server that is examined for Operation and Operand match. Operation This is the match method by which the string in Operand is matched with the attribute value returned by the authentication server. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show aaa derivation-rules | 605...
Page 606 This command was introduced in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master or local controllers 606 | show aaa derivation-rules Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 607: Usage Guidelines
This command was available in ArubaOS 6.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable and Config mode on local and master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show aaa dns-query-interval | 607...
Page 608 This command was available in ArubaOS 6.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable and Config mode on local and master controllers 608 | show aaa fqdn-server-names Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 609 Best practices are to enable this option when you use the aaa derivation-rules command to create a rule with the DHCP-Option rule type. This parameter is disabled by default. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show aaa main-profile | 609...
Page 610 This command was introduced in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master or local controllers 610 | show aaa main-profile Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 611 0. Minimum number of Lower The maximum number of lowercase letters required for a management user password. By Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show aaa password-policy mgmt | 611...
Page 612 Config mode this show command. Command History This command was introduced in ArubaOS 3.4.2. 612 | show aaa password-policy mgmt Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 613 Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master or local controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show aaa password-policy mgmt | 613...
Page 614 Name of the server group used for MAC authentication. 8021.X Authentication Profile Name of the 802.1X authentication profile. 8021.X Authentication Default Role Configured role assigned to the user after 802.1X authentication. 614 | show aaa profile Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 615 This command was introduced in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master or local controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show aaa profile | 615...
Page 616 Related Commands Command Description Mode aaa profile Use the command aaa profile to define AAA profiles. Config mode Command History This command was introduced in ArubaOS 3.0. 616 | show aaa radius-attributes Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 617 Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master or local controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show aaa radius-attributes | 617...
Page 618 Packets received from unknown clients: 0 Packets received with unknown request: 0 Total RFC3576 packets Received The output of the show aaa rfc-3576-server statistics command includes the following parameters: 618 | show aaa rfc-3576-server Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 619 This command was introduced in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master or local controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show aaa rfc-3576-server | 619...
Page 620: Show Aaa Server-Group
Servers Rules hits Out-of-service ---- ------- ----- ---- -------------- auth-profile-2 coltrane-server-group default group1 internal The output of the show aaa server-group summary command includes the following parameters: 620 | show aaa server-group Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 621 This is the match method by which the string in Match-Str is matched with the attribute Match-Op value returned by the authentication server. contains – The rule is applied if and only if the attribute value contains the string in parameter Operand. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show aaa server-group | 621...
Page 622 Config mode in the output of this show command. Command History This command was introduced in ArubaOS 3.0. 622 | show aaa server-group Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 623 Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master or local controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show aaa server-group | 623...
Page 624 This command was introduced in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master or local controllers 624 | show aaa state ap-group Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 625 --------------- ---------- 32235 Idled users = 3366 Mobility = Enabled fast age = Disabled Bandwidth contracts = 2/1 IP takeovers = 21 Ping/SYN/Session attacks = 0/0/0 Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show aaa state configuration | 625...
Page 626 Number of times the RADIUS server did not respond to the authentication Radius server timeouts request. Total number of captive portal authentications or authentication failures since the last controller reset. 626 | show aaa state configuration Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 627 This command was introduced in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master or local controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show aaa state configuration | 627...
Page 628 User Miss Number of ARP packets sent between the datapath and the controlpath. Number of 802.1q (VLAN tag) packets sent between the datapath and the controlpath. 8021q 628 | show aaa state debug-statistics Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 629 Number of users in tunnel forwarding mode that aged out after STM deauthentication, and timer expiration. dtunnel Number of users in decrypt tunnel forwarding mode that aged out after STM deau- thentication, and timer expiration. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show aaa state debug-statistics | 629...
Page 630 Number of authentication rejects for IPv4 users that were processed after the reject was received. IPv6 Number of authentication rejects for IPv6 users that were processed after the reject was received. Command History Release Modification ArubaOS 3.0 Command introduced 630 | show aaa state debug-statistics Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 631 Additional statistics for idled users and user rejects were introduced. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master or local or local controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show aaa state debug-statistics | 631...
Page 632 5519 user 781821 781821 wkey 27109 27109 user tmout 4164 4164 4160 4160 forw unenc 1787103 1787103 auth 5268 5268 5267 5267 aesccm key 17885 17885 632 | show aaa state messages Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 633 This command was introduced in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master or local controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show aaa state messages | 633...
Page 634 This command was introduced in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master and local controllers 634 | show aaa state mux-tunnel Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 635 This command was introduced in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master and local controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show aaa state station | 635...
Page 636 This command was introduced in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master and local controllers 636 | show aaa state user Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 637 (deprecated) show aaa sysgate-on-demand Syntax No parameters. Command History Release Modification ArubaOS 3.0 Command introduced. ArubaOS 3.4 Command deprecated. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show aaa sygate-on-demand (deprecated) | 637...
Page 638: Related Commands
VLAN ID or VLAN name from attributes returned by the server during authentication Command History This command was introduced in ArubaOS 3.0. 638 | show aaa tacacs-accounting Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 639 Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master or local controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show aaa tacacs-accounting | 639...
Page 640 This command was introduced in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master and local controllers 640 | show aaa tacacs-accounting Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 641 This command was introduced in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master and local controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show aaa timers | 641...
Page 642 This command was introduced in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master and local controllers 642 | show aaa web admin-port Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 643 This command was introduced in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master and local controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show aaa xml-api server | 643...
Page 644 Packets received from unknown clients: 0 (0) Packets received with unknown request: 0 (0) Requests Received/Success/Failed 0/0/0 (0/0/0) The output of this command includes the following parameters: 644 | show aaa xml-api statistics Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 645 MAC address Number of packets received from unknown clients. Packets received from unknown clients Number of packets received with unknown request Packets received with unknown request Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show aaa xml-api statistics | 645...
Page 646 This command was introduced in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master and local controllers 646 | show aaa xml-api statistics Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 647 Command History This command was available in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable and Config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show acl ace-table | 647...
Page 648 This ACL permits or denies traffic based on the source address of the packet. Starting index entry for the ACL’s access control entries ACE Index 648 | show acl acl-table Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 649 Command History This command was available in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable and Config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show acl acl-table | 649...
Page 650 Port Based Session ACL ---------------------- Policy Service Action Dest/Opcode New Hits Total Hits Index ------ ------- ------ ----------- -------- ---------- ---- validuser 10.1.1.0 255.255.255.0 deny 4655 validuser permit 2502 4656 650 | show acl hits Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 651 Number of ACL hits that occurred since this command was last issued. Total number of ACL hits recorded since the controller last reset. Total Hits Index number of the ACL. Index ACL number ACE number Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show acl hits | 651...
Page 652 Command History This command was available in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable and Config mode on master controllers 652 | show acl hits Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 653 Description discovery Dell APs send out periodic multicast and broadcast queries to locate the master controller. If the APs are in the same broadcast domain as the master controller and ADP is enabled on the controller, the controller automatically responds to the APs’...
Page 654 Command History This command was available in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master controllers 654 | show adp counters Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 655 The AP has a duplicate AP name. An AP with an external antenna is not provisioned with external antenna gain settings. Both radios on the AP are disabled. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap active | 655...
Page 656 This column displays any flags for this AP. The list of flag abbreviations is also included in Flags the output of the show ap active command. a = Reduce ARP packets in the air A = Enet1 in active/standby mode 656 | show ap active Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 657 The parameter ip6-addr was added to view data for an IPv6 AP. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap active | 657...
Page 658: Show Ap-Group
(host) #show ap-group corp1 AP group "corp1" ------------------- Parameter Value --------- ----- Virtual AP corp1-guest Virtual AP corp1-wpa2 802.11a radio profile default 802.11g radio profile profile1-g Wired AP profile default 658 | show ap-group Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 659 IDS profile for the AP group. IDS profile Mesh radio profile assigned to the AP group. Mesh Radio profile Mesh Cluster profile Mesh cluster profile assigned to the AP group. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap-group | 659...
Page 660 Configure AP group settings using the command ap-group. Command History This command was available in ArubaOS 3.0. Command Information Licensing Command Mode Platforms All platforms Base operating system Enable or Config mode on master controllers 660 | show ap-group Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 661 802.11a Traffic Management profile 802.11g Traffic Management profile Regulatory Domain profile RF Optimization profile RF Event Thresholds profile IDS profile Mesh Radio profile Mesh Cluster profile Excluded Mesh Cluster profile Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap-name | 661...
Page 662 Excludes the specified mesh cluster profile from this AP. Excluded Mesh Cluster profile Related Commands Configure AP settings using the command ap-name. Command History This command was available in ArubaOS 3.0. 662 | show ap-name Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 663 Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master and local controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap-name | 663...
Page 664 802.11a 40MHz (outdoor) 149-153 157-161 Command History Introduced in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master controllers 664 | show ap allowed-channels Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 665 802.11g Traffic Management profile Regulatory Domain profile corp13-channel-profile SNMP profile default RF Optimization profile handoff-aggressive RF Event Thresholds profile default IDS profile ids-low-setting Mesh Radio profile default Mesh Cluster profile Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap ap-group | 665...
Page 666 Configure your AP groups and AP group profiles. Config mode Command History Introduced in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master controllers 666 | show ap ap-group Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 667 I: Interference, R: Radar detection, N: Noise exceeded, E: Error threshold exceeded, INV: Invalid Channel, G: Rogue AP Containment, M: Empty Channel, P+: Increase Power, P-: Decrease Power, OFF: Turn off Radio, ON: Turn on Radio Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap arm history | 667...
Page 668 Command History Introduced in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master or local controllers 668 | show ap arm history Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 669 00:16:b6:f4:59:94:known-interfering/SNR-0/CH-1 00:14:51:6d:d1:d5:known-interfering/SNR-0/CH-1 Command History Introduced in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap arm neighbors | 669...
Page 670 0/40//0/0 0/0//0/0 HT Channel Summary ------------------ channel_pair Pairwise_intf_index ------------ ------------------- 1054 7-11 4221 149-153 36-40 157-161 44-48 The output of this command includes the following information: 670 | show ap arm rf-summary Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 671 “x” is the AP’s weighted calculation of the Signal-to-Noise Ratio (SNR) on all valid APs on a specified 802.11 channel, and “y” is the weighted calculation of the Dell APs SNR the neighboring APs see on that channel.
Page 672 D: Default, V: Valid, A: AP Present, C: Reg Domain Channel, O: DOS Channel, T:20MHZ Channel, F: 40MHz Channel, L: Reg Domain 40MHz Channel (lower), U: Reg Domain 40MHz channel (U) 672 | show ap arm scan-times Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 673 Command History Introduced in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap arm scan-times | 673...
Page 674 Name of an AP. IP address of an AP. IP address Signal-to-noise (SNR) ratio. SNR is the power ratio between an information signal and the level of background noise. 674 | show ap arm state Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 675 ArubaOS 6.1 The neighbor density parameter was introduced. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap arm state | 675...
Page 676 AP to which the client was connected. The output of this command in the example below shows the association table for the client with the MAC address 00:13:fd:5c:7c:59. If the flags column in the output of this command 676 | show ap association Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 677 Number of clients associated with the AP. This column displays any flags for this AP. The list of flag abbreviations is included in the flags output of the show ap association command. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap association | 677...
Page 678 Command History Introduced in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master controllers 678 | show ap association Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 679 The output of this command includes the following information: Column Description Name Name of an AP The AP Basic Service Set Identifier (BSSID) bssid MAC address of the AP Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap association remote | 679...
Page 680 Command History Introduced in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master controllers 680 | show ap association remote Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 681 AP Authorization profile "default" (Predefined (editable)) ---------------------------------------------------------- Parameter Value --------- ----- AP authorization group NoAuthApGroup The output of the show ap authorization command includes the following parameters: Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap authorization-profile | 681...
Page 682: Related Commands
This command was introduced in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master or local controllers 682 | show ap authorization-profile Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 683 Amount of time the client has been blocked, in seconds. block-time (sec) Amount of time remaining before the client will be allowed access to the network again. remaining time(sec) Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap blacklist-clients | 683...
Page 684 <macaddr> Command History Introduced in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master controllers 684 | show ap blacklist-clients Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 685 Usage Guidelines The output of the show ap bss-table command shows the Dell AP BSS table for all APs. To filter this information and view BSS table data for an individual AP or a specific port and slot number, include the ap-name, bssid, essid, ip-addr or port keywords.
Page 686 This data column will display a dash (-) if no ACLs are currently configured for the AP. Command History Introduced in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master controllers 686 | show ap bss-table Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 687 Show bandwidth data for an AP with a specific IP address by entering an IP address in ip-addr <ip-addr> dotted-decimal format. Examples The output of the following command shows the Dell AP bandwidth table for an AP with the IP address 192.0.2.170. show ap bw-report ip-addr 192.0.2.170 Bandwidth report for AP "AL16" radio 0...
Page 688 Average throughput for the virtual AP, in kbps. Command History Introduced in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master controllers 688 | show ap bw-report Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 689 1 second. Extended Service Set ID (ESSID) of the client. essid VLAN ID of the VLAN used by the client vlan-id Identification number for the tunnel tunnel-id Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap client status | 689...
Page 690 Command History Introduced in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master controllers 690 | show ap client status Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 691 10 sec 10 sec ap system-profile "default" Maximum Request Retries ap system-profile "default" Keepalive Interval 60 sec 60 sec ap system-profile "default" Dump Server ap system-profile "default" Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap config | 691...
Page 692 Description LMS IP The IPv4 address of the local management switch (LMS)— the Dell controller which is responsible for terminating user traffic from the APs, and processing and forwarding the traffic to the wired network. The IPv6 address of the local management switch (LMS)—...
Page 693 After the maximum number of retries, the AP either reboots or tries the IP address specified by the backup LMS IP address (if configured). Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap config | 693...
Page 694 Enable or disable local network access across VLANs in a Remote-AP Local Network Access Remote-AP. Radio enable Shows if the AP’s radio is enabled or disabled. Shows the operating modes for the AP. Mode 694 | show ap config Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 695 If an AP’s client load is at or over a predetermined threshold as compared to its immediate neighbors, or if a neighboring Dell AP on another channel does not have any clients, load balancing will be enabled on that AP. This feature is disabled by default.
Page 696 (in -dBm). The AP will filter out and ignore weak signals that are below the channel threshold signal strength. If the value is set to zero, the feature will automatically determine an appropriate threshold 696 | show ap config Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 697 AP. An AP in hybrid AP mode will continue to serve clients as an access point while it scans and analyzes spectrum analysis data for a single radio channel. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap config | 697...
Page 698 Active Scan is disabled by default, and should not be enabled except under the direct supervision of Dell Support. Shows if scanning is enabled or disabled for this AP. If this...
Page 699 Parameter Description Default: enabled The Dell coverage index metric is a weighted calculation Ideal Coverage Index based on the RF coverage for all DellAPs and neighboring APs on a specified channel. The Ideal Coverage Index specifies the ideal coverage that an AP should try to achieve on its channel.
Page 700 AP to respond with Clear to Send (CTS). This helps prevent mid-air collisions for wireless clients that are not within wireless peer range and cannot detect when other wireless clients are transmitting. 700 | show ap config Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 701 If disabled, the AP will not resend probes if it does not get a Disable Probe Retry response. Shows if the battery boost feature is enabled or disabled for Battery Boost Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap config | 701...
Page 702 Shows if the AP has enabled or disabled the use of its high- High throughput enable (SSID) throughput SSID in 40 MHz mode. 40 MHz channel usage Determines if this high-throughput SSID allows high- throughput (802.11n) stations to associate. 702 | show ap config Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 703 APs. Shows the band(s) on which to use the virtual AP: Allowed band a—802.11a band only (5 GHz) g—802.11b/g band only (2.4 GHz) Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap config | 703...
Page 704 Authentication Failure Blacklist Time Shows the time, in seconds, a client is blocked if it fails repeated authentication. If the virtual AP shows a value of 0, 704 | show ap config Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 705 Shows the maximum bandwidth that can be handled by one VoIP Bandwidth based CAC radio, in kbps. Show the number of simultaneous calls that can be handled VoIP Call Capacity by one radio. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap config | 705...
Page 706: Related Commands
Use the commands displayed in the column to the left rf arm-profile to configure these parameters. rf ht-radio-profile wlan ht-ssid-profile wlan virtual-ap wlan voip-cac-profile Command History Introduced in ArubaOS 3.0. 706 | show ap config Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 707 Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap config | 707...
Page 708 Description Show information for APs that have detected coverage holes in the wireless network. Command History Version Description ArubaOS 2.0 Command introduced ArubaOS 6.1 Command deprecated 708 | show ap coverage-holes (deprecated) Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 709 If used with the sort-by keyword, status sorts the output of the command by status up|down status type (up or down.) Otherwise, use the status keyword to display APs with the specified status. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap database | 709...
Page 710: Usage Guidelines
192.0.2.58 Up 1h:43m:18s 10.4.97.10 AP-61-20 default 192.0.2.59 Up 21m:36s 10.3.47.189 Flags: U = Unprovisioned; N = Duplicate name; G = No such group; L = Unlicensed 710 | show ap database Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 711 Command introduced ArubaOS 6.2 The usb parameter was introduced Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap database | 711...
Page 712 Total number of APs with an active (up) IPsec tunnel. IPSEC Up Total number of APs with an inactive (down) IPsec tunnel. IPSEC Down Command History Introduced in ArubaOS 3.0. 712 | show ap database-summary Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 713 Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap database-summary | 713...
Page 714 Display association failure information that can be used to troubleshoot problems on an AP. Command History Platforms Licensing ArubaOS 3.0 Command introduced ArubaOS 5.0 Command deprecated 714 | show ap debug association-failure (dep- Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide recated)
Page 715 10.6.1.197 g-HT ap tunnel 0x14c enable enable enable 00:1a:1e:11:5f:11 wpa2 10.6.1.200 a-HT ap tunnel 0x150 0xff0 enable enable The output of this command includes the following information: Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap debug bss-config | 715...
Page 716 Command History Introduced in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master controllers 716 | show ap debug bss-config Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 717 Last SNR Last ACK SNR Last ACK SNR CTL0 Last ACK SNR CTL1 Last ACK SNR CTL2 The output of this command includes the following information: Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap debug bss-stats | 717...
Page 718 Tx HT 120 Mbps Tx HT 162 Mbps Number of frames transmitted at 162 Mbps. Number of frames transmitted at 180 Mbps. Tx HT 180 Mbps 718 | show ap debug bss-stats Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 719 Signal-to-noise ratio for the last received ACK packet on the secondary (extension) channel Last ACK SNR EXT2 2. This parameter is only displayed for APs operating in 40 Mhz mode. Frames Received Number of frames received. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap debug bss-stats | 719...
Page 720 Rx 54 Mbps Command History Introduced in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master controllers 720 | show ap debug bss-stats Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 721 Number of times an AP updated its statistics with the controller. AP Stats Update Message 3087 (For internal use only) (For internal use only) Tunnel VLAN Membership Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap debug client-mgmt-counters | 721...
Page 722 (For internal use only) Command History Introduced in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master controllers 722 | show ap debug client-mgmt-counters Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 723 Rx Data Frames 2930 Null Data Frames 2879 Rx Mgmt Frames PS Poll Frames Rx 6 Mbps Rx 12 Mbps Rx 18 Mbps Rx 24 Mbps Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap debug client-stats | 723...
Page 724 1. This parameter is only displayed for APs operating in 40 Mhz mode. The signal-to-noise ratio for the last received data packet on the secondary (control) Last SNR CTL2 724 | show ap debug client-stats Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 725 Tx WMM [VI]: Video Command History Introduced in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap debug client-stats | 725...
Page 726: Usage Guidelines
D - Delayed BA; G - Greenfield; R - Dynamic SM PS Q - Static SM PS; N - A-MPDU disabled The output of this command includes the following information: 726 | show ap debug client-table Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 727 Number of packets that the client had to resend due to an initial transmission failure. Tx_Retries Command History Introduced in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap debug client-table | 727...
Page 728 AL19 corp1 10.6.1.212 AP Boots Acked Bootstraps (Total) Reboots Crash -------------- ------------------ ------- ----- Total APs :6 The output of this command includes the following information: 728 | show ap debug counters Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 729 Command History Introduced in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap debug counters | 729...
Page 730 <4>Checking for the daddi bug... no. <4>Checking for the daddiu bug... no. <5>detected lzma initramfs <5>initramfs: LZMA lc=3,lp=0,pb=2,dictSize=8388608,origSize=15217664 <5>LZMA initramfs Command History Introduced in ArubaOS 5.0. 730 | show ap debug crash-info Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 731 Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap debug crash-info | 731...
Page 732 If enabled, the AP will respond to broadcast probe requests. If disabled, the AP will not deny-bcast respond to these requests. Number of clients currently using the network. num-clients 732 | show ap debug datapath Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 733 Command History Introduced in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap debug datapath | 733...
Page 734 Use this command to review configuration changes made since the AP was last reset. Command History Introduced in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master controllers 734 | show ap debug driver-log Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 735 An AP’s log files show configuration changes since the AP was last reset. Command History Introduced in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap debug log | 735...
Page 736 (deprecated) Description Show traced 802.11 management frames. Command History Version Modification ArubaOS 3.0 Command Introduced ArubaOS 5.0 Command deprecated 736 | show ap debug mgmt-frames (deprecated) Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 737 Parameter Description Total number of times the radio reset. Total Radio Resets Number of times the radio reset due to beacon failure. Resets Beacon Fail Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap debug radio-stats | 737...
Page 738 If the ARM power-save aware scan feature is enabled, the AP will not scan a different PS aware Scan Rejects channel if it has one or more clients and is in power save mode. The ps aware Scan 738 | show ap debug radio-stats Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 739 Number of broadcast frames with DTIM values. DTIM Broadcast Number of frames that were transmitted after being retried. Success With Retry Tx Mgmt Frames Number of management frames transmitted. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap debug radio-stats | 739...
Page 740 Number of Wifi Multimedia (WMM) packets transmitted for the following access categories. If the AP has not transmitted packets in a category type, this data row will not 740 | show ap debug radio-stats Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 741 2. This parameter is only displayed for APs operating in 40 Mhz mode. Number of frames received. Frames Received Number of frames received with no errors. Good Frames Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap debug radio-stats | 741...
Page 742 Rx Frames Dropped The number of Physical Layer Events, that are not 802.11 packets, detected by radio as PHY Events part of its normal receive operation. 742 | show ap debug radio-stats Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 743 Parameter Description Number of times an AP detects a radar signature. Dell APs are DFS-compliant detects a RADAR Events radar signature, it will change its channel. The number of receive interrupts received by the CPU from the radio. RX Interrupts The number of Receive FIFO overruns.
Page 744 VoIP Aware Scan Enabled Power Save Aware Scan Enabled Load aware Scan Threshold 1250000 Bps 40 MHz intolerance Disabled Honor 40 MHz intolerance Enabled Legacy station workaround Disabled 744 | show ap debug received-config Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 745 Limit Displays whether or not the active scan feature is enabled. Active Scan This option elicits more information from nearby APs, but also creates Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap debug received-config | 745...
Page 746 Parameter Description additional management traffic on the network. Active Scan is disabled by default, and should not be enabled except under the direct supervision of Dell Support. Shows if VoIP aware scanning is enabled or disabled. If you use voice...
Page 747 Shows if the AP has enabled or disabled MAC protocol data unit (MDPU) MPDU Aggregation aggregation. Shows the maximum size, in bytes, of an A-MPDU that can be sent on the AP’s Max transmitted A-MPDU size high-throughput SSID. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap debug received-config | 747...
Page 748 AP profile. Command History Introduced in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master controllers 748 | show ap debug received-config Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 749: Usage Guidelines
MAC address of the client that failed to associate with an AP. Name of an AP to which the client attempted to associate. AP Name Basic Service Set Identifier of an AP. BSSID Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap remote debug association-failure | 749...
Page 750 Reason Command History Introduced in ArubaOS 5.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master controllers 750 | show ap remote debug association-failure Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 751 Numcl TotCl BWmgmt 8144 0-0-0 0-2-0 tokens last-t drop tx-t rx-t al-t rate 2966 The output of this command includes the following information: Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap debug shaping-table | 751...
Page 752 (For internal use only.) rate Command History Introduced in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master controllers 752 | show ap debug shaping-table Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 753 Low values in this table can indicate problems with the wired network, or with the AP itself. Tunnel Heartbeat table This table can indicate the health of the underlying wired network. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap debug system-status | 753...
Page 754 Crash information parameter was introduced. ArubaOS 3.0 Command introduced Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master controllers 754 | show ap debug system-status Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 755 00:1a:1e:c5:d9:56 00:1a:1e:c5:d9:b0 Command History Introduced in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap debug trace-addr | 755...
Page 756 4G-LTE Command History Introduced in ArubaOS 6.2. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master controllers 756 | show ap debug usb ap-name Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 757 Serial # AD0054972 Wired MAC Address 00:1a:1e:c9:17:38 Radio 0 BSSID 00:1a:1e:11:73:90 Radio 1 BSSID 00:1a:1e:11:73:80 Enet 1 MAC Address 00:1a:1e:c9:17:39 AP "AL39" Operating Information ------------------------------- Item Value Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap details | 757...
Page 758 IP address of the AP AP IP Address LMS IP Address The IP address of the local management switch (LMS)—the Dell controller which is responsible for terminating user traffic from the APs, and processing and forwarding the traffic to the wired network.
Page 759 Domain name used by the AP. Domain Name DNS name of the controller from which the AP boots. Server Name IP address of the controller from which the AP boots Server IP Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap details | 759...
Page 760 Horizontal coverage distance of the 802.11g (2.4GHz) antenna from true north, Antenna bearing for 802.11g from 0-360 degrees. 760 | show ap details Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 761 The parameter ip6-addr was added to show data for an IPv6 AP. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap details | 761...
Page 762 This command configures an AP Ethernet link profile. Config mode Command History Introduced in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master controllers 762 | show ap enet-link-profile Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 763 Command History Introduced in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap essid | 763...
Page 764 802.11n data rates for the MCS for 40 Mhz transmissions. 40 MHz 802.11n data rates for the MCS for 40 Mhz transmissions using a short guard interval. 40 MHz SGI 764 | show ap ht-rates Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 765 Command History Introduced in ArubaOS 3.3. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap ht-rates | 765...
Page 766 Matches If yes, the running image version matches the image version currently in the AP’s flash memory. If no, the two image versions do not match. 766 | show ap image version Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 767 In progress: The AP is currently updating its image. Command History Introduced in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap image version | 767...
Page 768 Overall AP Licenses CAPs Number of campus APs currently using a license on the controller. Number of remote APs currently using a license on the controller. RAPs 768 | show ap license-usage Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 769 All platforms Base operating system. The output of this command varies, according Enable or Config mode on to the licenses currently installed on the controller. master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap license-usage | 769...
Page 770 LLDP-MED network policy profile The output of this command includes the following information: Parameter Description PDU transmission Shows if LLDP PDU transmission is enabled on the AP. 770 | show ap lldp Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 771 Command History Command introduced in ArubaOS 6.2. Command Information Platforms Licensing Command Mode All platforms Base operating system. Enable or Config mode on master or local controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap lldp | 771...
Page 772 Number of times that an LLDP neighbor could not be added to the neighbor table (there is Overflow a limit of 8 per port) Number of packets transmitted from that interface Transmitted 772 | show ap lldp counters Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 773 Command History Command introduced in ArubaOS 6.2. Command Information Platforms Licensing Command Mode All platforms Base operating system. Enable or Config mode on master or local controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap lldp counters | 773...
Page 774 AP LLDP-MED Network Policy Profile "default" -------------------------------------------- Parameter Value --------- ----- LLDP-MED application type streaming-video LLDP-MED application VLAN LLDP-MED application VLAN tagging Tagged LLDP-MED application Layer-2 priority 774 | show ap lldp med-network-policy-profile Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 775 0 is the Services Code Point lowest priority level and 63 is the highest priority. Command History Command introduced in ArubaOS 6.2. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap lldp med-network-policy-profile | 775...
Page 776 Command Information Platforms Licensing Command Mode All platforms Base operating system. Enable or Config mode on master or local controllers 776 | show ap lldp med-network-policy-profile Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 777 Name of the LLDP neighbor Interface on the AP sending or receiving LLDP PDUs. Interface Neighbor LLDP neighbor number The name of the LLDP neighbor AP Chassis Name/ID Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap lldp neighbors | 777...
Page 778 Command History Command introduced in ArubaOS 6.2. Command Information Platforms Licensing Command Mode All platforms Base operating system. Enable or Config mode on master or local controllers 778 | show ap lldp neighbors Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 779 AP’s regulatory domain (country). cur-cl Current number of clients on the AP. Current bandwidth utilization, in kbps. util (kbps) Command History Introduced in ArubaOS 3.0. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap load-balancing | 779...
Page 780 Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master controllers 780 | show ap load-balancing Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 781 14d:21h:14m:55s 14d:19h:5m:3s The output of this command includes the following information: Column Description Name of an AP. Name AP group which includes the specified AP. Group Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap mesh active | 781...
Page 782 Enable or Config mode on master controllers the base operating system. Commands to configure the secure enterprise mesh solution for outdoor APs require the Outdoor Mesh license. 782 | show ap mesh active Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 783 The WPA pre-shared key (only for mesh cluster profiles using WPA2 with AES encryption). WPA Hexkey The WPA password that generates the preshared key (only for mesh cluster profiles using WPA Passphrase WPA2 with AES encryption). Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap mesh-cluster-profile | 783...
Page 784 This show command is available in Enable or Config mode on master controllers the base operating system. Commands to configure the mesh feature require the Mesh license. 784 | show ap mesh-cluster-profile Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 785 Enter recovery mode Exit recovery mode Total connections to switch Mesh loop-prevention Sequence No.:1256947 Mesh timer ticks:68930 The output of this command includes the following information: Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap mesh debug counters | 785...
Page 786 This show command is available in Enable or Config mode on master controllers. the base operating system. Commands to configure the mesh feature require the Mesh license. 786 | show ap mesh debug counters Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 787 The WPA pre-shared key (only for mesh cluster profiles using WPA2 with AES encryption). WPA Hexkey The WPA password that generates the preshared key (only for mesh cluster profiles using WPA Passphrase WPA2 with AES encryption). Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap mesh debug current-cluster | 787...
Page 788 This show command is available in Enable or Config mode on master controllers the base operating system. Commands to configure the mesh feature require the Mesh license. 788 | show ap mesh debug current-cluster Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 789 Show data for a remote mesh node with a specific IP address by entering its IP address in ip-addr <ip-addr> dotted-decimal format. Usage Guidelines This is an internal technical support command. Dell technical support may request that you issue this command to help analyze and troubleshoot problems with your mesh network. Command History Introduced in ArubaOS 3.0.
Page 790 <ip-addr> decimal format. Usage Guidelines This is an internal technical support command. Dell technical support may request that you issue this command to help analyze and troubleshoot problems with the hostapd process or your mesh network. Command History Introduced in ArubaOS 3.0.
Page 791 If this parameter is omitted, this command will display all meshd log information, oldest first. Usage Guidelines This is an internal technical support command. Dell technical support may request that you issue this command to help analyze and troubleshoot problems with the meshd process or your mesh network. Command History...
Page 792 The output of this command displays the following information for the AP’s mesh cluster profile and recovery cluster profiles: Column Description Cluster Name Name of the mesh cluster using this profile RF band The RF band in which the AP should operate: 792 | show ap mesh debug provisioned-clusters Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 793 This show command is available in Enable or Config mode on master controllers the base operating system. Commands to configure the mesh feature require the Mesh license. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap mesh debug provisioned-clusters | 793...
Page 794 The output of this command includes the following information: Column Description This parameter shows if the profile enables or disables the 40 MHz channel usage use of 40 MHz channels. 794 | show ap mesh-ht-ssid-profile Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 795 (400ns) guard interval in 20 MHz mode. Shows if the profile enables or disables use of short Short guard interval in 20 MHz mode (400ns) guard interval in 40 MHz mode. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap mesh-ht-ssid-profile | 795...
Page 796 Maximum number of spatial streams usable for STBC transmission Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master controllers 796 | show ap mesh-ht-ssid-profile Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 797 00:1a:1e:88:02:90 00:1a:1e:88:01:f0 157+ 2.00 N 3h:35m:6s A-Req A-Resp A-Fail HT-Details Cluster ID ----- ------ ------ ---------- ---------- Unsupported sw-ad-GB32 HT-40MHzsgi-2ss sw-ad-GB322 Unsupported Unsupported sw-ad-GB32 HT-40MHzsgi-2ss sw-ad-GB32 Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap mesh neighbors | 797...
Page 798 Number of association responses from the mesh node Number of association failures A-Fail Name of the Mesh cluster that includes the specified AP or BSSID. Cluster 798 | show ap mesh neighbors Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 799 This show command is available in Enable or Config mode on master controllers the base operating system. Commands to configure the mesh feature require the Mesh license. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap mesh neighbors | 799...
Page 800 Rate Optimization for delivering EAPOL frames and mesh echoes Disabled Reselection mode startup-subthreshold Retry Limit RTS Threshold 2333 bytes The output of this command includes the following information: 800 | show ap mesh-radio-profile Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 801 The reselection process is canceled if the average RSSI rises on the existing uplink rises above the configured link threshold. reselect-any-time: Connected mesh nodes evaluate Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap mesh-radio-profile | 801...
Page 802 The Rate Optimization for delivering EAPOL frames and mesh echoes parameter was introduced. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master controllers 802 | show ap mesh-radio-profile Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 803 All platforms This show command is available in Config mode on master controllers the base operating system. Commands to configure the mesh feature require the Mesh license. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap mesh tech-support | 803...
Page 804 (R): Recovery AP. (N): 11N Enabled. For Portals 'Uplink Age' equals uptime. The output of this command includes the following information: Column Description Name of the mesh node. Name 804 | show ap mesh topology Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 805 This show command is available in Enable or Config mode on master controllers the base operating system. Commands to configure the mesh feature require the Mesh license. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap mesh topology | 805...
Page 806 Wired Containment Counters: Last Wired Containment Timer Tick Last Tagged Wired Containment Timer Tick Spoof frames sent Spoof frames sent on tagged VLAN Show IDS State. ids-state 806 | show ap monitor Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 807 The output of the command displays the Monitored AP table, which lists all the APs monitored by a specified AP or BSSID. (host) #show ap monitor ap-list ap-name al12 Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap monitor | 807...
Page 808 Radio channel used by the BSSID chan Radio phy type. Possible types include: phy-type 802.11a 802.11a-HT-40 802.11b/g 802.11b/g-HT-20 Shows if the feature to contain DoS attacks has been enabled or disabled. 808 | show ap monitor Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 809 Added the following parameter to ids-state: ap-name bssid ip-addr Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap monitor | 809...
Page 810 Displays a yes if the client has been authenticated. auth The RF band in which the AP should operate: phy-type 802.11g = 2.4 GHz 802.11a = 5 GHz 810 | show ap monitor association Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 811 Command History Introduced in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap monitor association | 811...
Page 812 Show an Air Monitor IDS Signature Matching configuration settings, as defined ids-signature-matching in its IDS Signature Matching profile ids-unauthorized-device Show an Air Monitor IDS Unauthorized Device configuration settings, as defined in its IDS Unauthorized Device profile. 812 | show ap monitor debug Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 813 3323085 AP Name AL12 LMS IP Master IP AP Type Country Code Data Structures ---------------- psta msg-hash ap-l ---- -------- ---- Other Parameters ----------------- value ----- Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap monitor debug | 813...
Page 814 Number of packets seen on the interface. MAC address for the AP’s wired interface. The AP’s IP address. gw-ip IP address for the AP’s gateway. gw-mac MAC address for the AP’s gateway. 814 | show ap monitor debug Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 815 Number of channel entries in the channel table. msg-hash Number of different message types seen on the interface. ap-l (For internal use only) Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap monitor debug | 815...
Page 816 Command introduced ArubaOS 3.4. The tagged-pkts and vlan parameters were added to the Wired Interface table in the output of the show ap monitor debug status command. 816 | show ap monitor debug Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 817 Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap monitor debug | 817...
Page 818 (sec) ---------- ---------- ----------- ----- -------------- Monitored Time:6626 Last Packet Time:585500 Uptime:585502 DoS Frames ---------- old-tx old-rx ------ ------ Interference Baseline --------------------- 818 | show ap monitor stats Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 819 This value indicates the number of consecutive timer ticks over which the value of the Receive Signal Strength Indicator (RSSI) of the client has reduced by more than 3 units. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap monitor stats | 819...
Page 820 Indicates whether the specified MAC address is 40 Mhz intolerant. 40mhz-intolerance Command History Introduced in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master controllers 820 | show ap monitor stats Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 821: Usage Guidelines
IP6 address of the AP for which you are requesting packet capture status information. Usage Guidelines This is the show version for the ap packet-capture commands, used to direct an Dell AP to send packet captures to a client packet capture utility such as Airmagnet, Wireshark and so on, on a remote client.
Page 822 AP. Command History Introduced in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master controllers 822 | show ap profile-usage Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 823 Antenna gain for 802.11a Antenna gain for 802.11g Antenna for 802.11a both Antenna for 802.11g both Single chain mode for Radio 0 Single chain mode for Radio 1 Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap provisioning | 823...
Page 824 2: AP uses antenna 2 both: AP uses both antennas Antenna use for 2.4 GHz (802.11g) frequency band. Antenna for 802.11g 1: AP uses antenna 1 2: AP uses antenna 2 824 | show ap provisioning Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 825 If the mesh role is “none,” the AP is operating as a thin AP. An AP operating as a Mesh Role mesh node can have one of two roles: mesh portal or mesh point. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap provisioning | 825...
Page 826: Related Commands
ArubaOS 3.2 Introduced support for mesh parameters, additional antenna parameters, and AP location parameters. ArubaOS 3.4 Introduced support for the following parameters: Installation Mesh SAE USB User Name 826 | show ap provisioning Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 827 Only the sae-disable option indicates that this parameter is currently in its default disabled state. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap provisioning | 827...
Page 828 Master IP/FQDN PPPOE User Name PPPOE Password PPPOE Service Name USB User Name USB Password USB Device Type USB Device Identifier USB Dial String USB Initialization String 828 | show ap provisioning-profile Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 829 If your AP uses PEAP authentication, this field displays the AP Username of AP so that AP can authenticate username. to 802.1x using PEAP Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap provisioning-profile | 829...
Page 830 ArubaOS 3.0 Command introduced ArubaOS 6.0 The uplink-vlan parameter was introduced. Command Information Platforms Licensing Command Mode All platforms Base operating system Config mode on master controllers 830 | show ap provisioning-profile Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 831 Sort the output of this command by controller ip address switch-ip sort-direction Select a sort direction for the output of this command ascending Sort the output in ascending order. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap radio-database | 831...
Page 832 Switch IP IP address of the AP’s controller. 11g Mode/Chan/EIRP/Cli 802.1g radio type and mode/802.11g radio channel used by the AP/current Effective 832 | show ap radio-database Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 833 In the actual command-line interface, it will appear in a single, long table. (host) #show ap radio-summary APs Radios information ---------------------- Name Group AP Type IP Address Band Mode ---- ----- ------- ---------- ---- ---- Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap radio-summary | 833...
Page 834 Noise Floor (dBm)/Utilization (%)/Interference (%). Time used by data frames (%). Time used by mgmt frames(%). Time used by ctrl frames (%). Command History Introduced in ArubaOS6.2. 834 | show ap radio-summary Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 835 Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap radio-summary | 835...
Page 836 Valid 802.11a channel Valid 802.11a channel Valid 802.11g 40MHz channel pair Valid 802.11a 40MHz channel pair 36-40 Valid 802.11a 40MHz channel pair 44-48 Valid 802.11a 40MHz channel pair 149-153 836 | show ap regulatory-domain-profile Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 837 These channels are limited to those valid for the profile’s country code. channel pair Command History Introduced in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap regulatory-domain-profile | 837...
Page 838 Number of counters recorded since the AP was last reset. Value Command History Introduced in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master controllers 838 | show ap remote counters Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 839 Num Clients:1 The output of this command includes the following information: Column Description Name Name of an AP. The AP Basic Service Set Identifier (BSSID). bssid Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap remote debug association | 839...
Page 840 Command History Introduced in ArubaOS 5.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master controllers 840 | show ap remote debug association Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 841 Association Table ----------------- Association Table ----------------- ----------------- Name bssid auth assoc l-int essid ---- ----- ---- ----- ----- ----- AL12 00:1a:1e:11:5f:11 00:21:5c:50:b1:ed ethersphere-wpa2 00:1a:1e:88:88:31 00:19:7d:d6:74:93 ethersphere-wpa2 Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap remote debug association | 841...
Page 842 Command History Introduced in ArubaOS 5.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master controllers 842 | show ap remote debug association Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 843 This column shows if the BSSID is for an access point (ap) or an air monitor (am). fw-mode The configured forward mode for the AP’s virtual AP profile. bridge: Bridge locally Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap remote debug bss-config | 843...
Page 844 Command History Introduced in ArubaOS 5.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master controllers 844 | show ap remote debug bss-config Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 845 Number of times a client was validated. Validate Client Number of times an AP updated its statistics with the controller. AP Stats Update Message 3087 (For internal use only) Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap remote debug client-mgmt-counters | 845...
Page 846 Number of 802.11 disassociation messages to the controller. disassoc Number of 802.11 deauthorization messages from the controller. deauth (For internal use only) sapcp Command History Introduced in ArubaOS 5.0. 846 | show ap remote debug client-mgmt-counters Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 847 Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap remote debug client-mgmt-counters | 847...
Page 848 DHCP LEASE Session ACL Session ACL Name Session ACL Count Session Aces ACL 1 ACL 1 Name logon ACL 1 Count Aces 1 16 1 4294 848 | show ap remote debug flash-config Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 849 ACL1 Aces Command History Introduced in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap remote debug flash-config | 849...
Page 850 The output of this command includes the following information: Column Description The time the management frame was sent Timestamp stype One of the following 802.11 frame types: auth: Authorization frame deauth: Deauthorization frame 850 | show ap remote debug mgmt-frames Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 851 Command History Introduced in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap remote debug mgmt-frames | 851...
Page 852 93 31 bd 44 58 fe fe 6a ad aa 1d d7 29 94 fb 5b 7c 15 76 66 d2 1f Command History Introduced in ArubaOS 6.2. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable mode on master controllers 852 | show ap remote debug r1_key Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 853 The Spectrum Analysis feature provides visibility into RF coverage, allowing you to troubleshoot RF interference and identify 802.11 devices on the network. Issue this command to display and sort APs seen by a specific spectrum monitor. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap spectrum ap-list | 853...
Page 854 BSS (an ibss bit in an 802.11 frame). Time when the AP was first detected by the spectrum monitor. add-time Time when the AP was last seen by the spectrum monitor. last-seen 854 | show ap spectrum ap-list Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 855: Related Commands
Command History Introduced in ArubaOS 6.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master or local controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap spectrum ap-list | 855...
Page 856 The output of this example shows part of the channel metrics table for channels seen by the spectrum monitor ap123. (host)# show ap spectrum channel-metrics ap-name ap123 freq-band 2.4GHz 856 | show ap spectrum channel-metrics Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 857 Set a 802.11a radio so the device operates as Config mode on master or local an spectrum monitor, and can send spectrum controllers analysis data to a desktop or laptop client. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap spectrum channel-metrics | 857...
Page 858 Command History Introduced in ArubaOS 6.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master or local controllers 858 | show ap spectrum channel-metrics Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 859 --------------------- Channel KnownAPs UnknownAPs Util(%) MaxAPSignal(dBm) MaxInterference(dBm) SNIR(dB) ------- -------- ---------- ------- ---------------- -------------------- ------- 149+ 157+ The output of this command includes the following information: Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap spectrum channel-summary | 859...
Page 860 Command History Introduced in ArubaOS 6.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master or local controllers 860 | show ap spectrum channel-summary Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 861 View information for a specific radio type, either 2.4 GHz or 5 GHz. freq-band 2.4ghz|5ghz Usage Guidelines Use this command to view channel and signal information for wireless clients seen by the spectrum monitor. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap spectrum client-list | 861...
Page 862 Identifier assigned to the client by the spectrum monitor. spectrum-id Radio channel used by the BSSID chan Radio phy type. Possible types include: phy-type 802.11a 802.11a-HT-40 802.11b/g 802.11b/g-HT-20 862 | show ap spectrum client-list Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 863 Command History Introduced in ArubaOS 6.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master or local controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap spectrum client-list | 863...
Page 864 IP address of the spectrum monitor for which you want to view spectrum information. Save information for a specific radio type, either 2.4 GHz or 5 GHz. freq-band 2.4ghz|5ghz Usage Guidelines Use this command under the supervision of your Dell technical support representative to troubleshoot spectrum analysis issues or errors. Related Commands Command...
Page 865 Command History Introduced in ArubaOS 6.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master or local controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap spectrum debug | 865...
Page 866 Save FFT information received from driver and its normalized FFT raw-normalized Usage Guidelines Use this command under the guidance of an Dell technical support representative to troubleshoot FFT power issues seen on AP models AP-104, AP-92, AP-93, AP-93H, AP-175 and the AP-130 Series. Related Commands...
Page 867 Command History Introduced in ArubaOS 6.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master or local controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap spectrum debug fft | 867...
Page 868 "ap123"/0/5GHz 10.240.16.165 1700 2010-05-17 01:29:16 PM Success Unsubscribe-All "ap123"/-/- 10.240.16.165 1701 2010-05-17 02:44:18 PM Client Not found Subscribe "ap123"/1/2GHz 10.100.100.67 1716 2010-05-18 03:44:28 PM Success 868 | show ap spectrum debug monitors Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 869 Usage Guidelines Use this command under the guidance of an Dell technical support representative to troubleshoot spectrum analysis errors. Related Commands Command Description Mode ap spectrum local-override Convert an AP or AM into a spectrum Config mode on master or local...
Page 870 <ip-addr> View information for a specific radio type, either 2.4 GHz or 5 GHz. freq-band 2.4ghz|5ghz Usage Guidelines Use this command under the guidance of an Dell technical support representative to troubleshoot spectrum analysis errors. Related Commands Command Description...
Page 871 Generic Interferer 0 WIFI Microwave Bluetooth Generic Fixed Freq Cordless Phone FF Video Audio Generic Freq Hopper Cordless Network FH Xbox Microwave Inverter Cordless Base FH Total:7 Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap spectrum device-duty-cycle | 871...
Page 872 Command History Introduced in ArubaOS 6.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master or local controllers 872 | show ap spectrum device-duty-cycle Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 873 View information for video devices seen by the spectrum device. video xbox View information for Xbox devices seen by the spectrum device. NOTE: This option is available only for 2.4 GHz spectrum devices. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap spectrum device-history | 873...
Page 874 Microwave (Inverter). As in the Microwave category described above, there may be other equipment that behave like inverter microwaves in some industrial, healthcare or manufacturing 874 | show ap spectrum device-history Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 875 FH (frequency hopper) generic interferer microwave microwave inverter video xbox NOTE: For additional details about non-Wi-Fi device types shown in this table, see "Non-Wi-Fi Interferers" on page 874 Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap spectrum device-history | 875...
Page 876 Command History Introduced in ArubaOS 6.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master or local controllers 876 | show ap spectrum device-history Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 877 NOTE: This option is available only for 2.4 GHz spectrum devices. Show only video fixed frequency devices. video Show only xbox frequency hopper devices. xbox NOTE: This option is available only for 2.4 GHz spectrum devices. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap spectrum device-list | 877...
Page 878 APs assign a unique spectrum ID per device type. Center frequency of the signal sent from the device. Cfreq Bandwidth Channel bandwidth used by the device. Radio channels affected by the wireless device. Channels-affected 878 | show ap spectrum device-list Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 879 Command History Introduced in ArubaOS 6.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master or local controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap spectrum device-list | 879...
Page 880 Show only video fixed frequency devices. video Show only xbox frequency hopper devices. xbox NOTE: This option is available only for 2.4 GHz spectrum device radios. 880 | show ap spectrum device-log Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 881 ID per device type. The non-Wi-Fi Device Log table can show signal data for a device when that device was Added/Deleted added or removed from the log table. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap spectrum device-log | 881...
Page 882 Command History Introduced in ArubaOS 6.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master or local controllers 882 | show ap spectrum device-log Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 883 Device Summary Table -------------------- Device ------- Unknown WIFI Microwave Bluetooth Generic Fixed Freq Cordless Phone FF Video Audio Generic Freq Hopper Cordless Phone FH Xbox Microwave Inverter Total:12 Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap spectrum device-summary | 883...
Page 884 Command History Introduced in ArubaOS 6.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master or local controllers 884 | show ap spectrum device-summary Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 885 The output of this example shows interference power levels for each channel seen by the spectrum monitor ap123. (host)# show ap spectrum interference-power ap-name ap123 freq-band 5ghz Interference Power Table ------------------------ Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap spectrum interference-power | 885...
Page 886 Command History Introduced in ArubaOS 6.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master or local controllers 886 | show ap spectrum interference-power Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 887 Number of clients currently using the AP. Command History Introduced in ArubaOS 3.3.2.14. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap spectrum-load-balancing | 887...
Page 888 Set a 802.11g radio so the device operates Config mode on master or local mode as an spectrum monitor, and can send controllers spectrum analysis data to a desktop or laptop client. 888 | show ap spectrum local-override Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 889 Command History Introduced in ArubaOS 6.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master or local controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap spectrum local-override | 889...
Page 890 IP address of the client to which the spectrum monitor or hybrid AP is sending data. Client IP Time at which the spectrum monitor or hybrid AP was connected to the client. Subscribe time Command History Introduced in ArubaOS 6.0. 890 | show ap spectrum monitors Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 891 Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master or local controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap spectrum monitors | 891...
Page 892 <filename> on the controller, the show ap spectrum technical-support command will create this file. Usage Guidelines Use this command under the supervision of your Dell technical support representative to troubleshoot spectrum analysis issues or errors. Command History Introduced in ArubaOS 6.0.
Page 893 Remote-AP Local Network Access Disabled Bootstrap threshold Double Encrypt Disabled Dump Server Heartbeat DSCP Maintenance Mode Disabled Maximum Request Retries Request Retry Interval 10 secNumber of IPSEC retries Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap system-profile | 893...
Page 894 In multi-controller ipv6 networks, this parameter Backup LMS IPv6 specifies the IPv6 address of a backup to the IPv6 address specified with the LMS IPv6 setting. 894 | show ap system-profile Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 895 GRE tunnel timeout is 1.5 x bootstrap- threshold; the tunnel is torn down after this number of seconds of inactivity on the tunnel. This parameter applies only to remote APs. Double Double Encrypt Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap system-profile | 895...
Page 896 Shared secret key for the server Frequency at which packets are sent to the server, in seconds Reports whether telnet access the AP is enabled or Telnet disabled. 896 | show ap system-profile Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 897 Added support for the option to set the RF scanning band (am-scan-rf-band). The keepalive-interval parameter was deprecated. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap system-profile | 897...
Page 898 Save the output of this command into a file on the controller with the specified filename. <filename> Usage Guidelines This is an internal technical support command. Dell technical support may request that you issue this command to help analyze and troubleshoot problems with an AP or your wireless network. Command History Introduced in ArubaOS 3.0.
Page 899 Number of clients currently using the specified VLAN. Clients Command History Introduced in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap vlan-usage | 899...
Page 900 The profile’s switching mode. Switchport mode access: Set access mode characteristics of the interface. mode: Set trunking mode of the interface. trunk: Set trunk mode characteristics of the interface. 900 | show ap wired-ap-profile Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 901 Do Not Broadcast, broadcast traffic will not be forwarded. Command History Introduced in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap wired-ap-profile | 901...
Page 902 An Ethernet Link profile to be used by devices connecting to the AP’s wired Ethernet interface link profile port profile. This profile defines the duplex value and speed to be used by the port. 902 | show ap wired-port-profile Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 903 Command History This command was introduced in ArubaOS 5.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap wired-port-profile | 903...
Page 904 The output of this command includes the following information: Column Description Slot number Slot Port number Port Associated VLAN number VLAN TX Packets Number of packets sent 904 | show ap wired stats Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 905 TX Multicast Bytes Command History Introduced in ArubaOS 5.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap wired stats | 905...
Page 906 6:prio 6:inactivity 2157352960 us:bidir:apsd:normalack:tclas prio 6 ip DIP-192.168.101.194 DP-32514 DSCP-48:one-match AP125-srk 00:90:7a:06:1f:5b tsid 0:prio 0:inactivity 100000000 us:bidir:apsd:normalack:no-match Num Flows:0 The output of this command includes the following parameters: 906 | show ap wmm-flow Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 907 DCSP: The Differentiated Services Code Point (DSCP) priority value that matches the flows 802.1p priority. Command History Introduced in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show ap wmm-flow | 907...
Page 908: Related Commands
Command History This command was available in ArubaOS 3.0. Command Information Licensing Command Mode Platforms All platforms Base operating system Enable and Config mode on master and local controllers 908 | show arp Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 909 This command was available in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Available in Enable and Config modes. Audit trails can only be enabled on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show audit-trail | 909...
Page 910 00:09:ef:05:1e:b2 00:1a:1e:97:e5:42 5 08:08:33 wpa2-key2 -> 00:09:ef:05:1e:b2 00:1a:1e:97:e5:42 failure 5 08:08:34 wpa2-key1 <- 00:09:ef:05:1e:b2 00:1a:1e:97:e5:42 5 08:08:34 wpa2-key2 -> 00:09:ef:05:1e:b2 00:1a:1e:97:e5:42 failure 5 08:08:35 wpa2-key1 <- 00:09:ef:05:1e:b2 00:1a:1e:97:e5:42 910 | show auth-tracebuf Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 911 This command was available in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Available in Enable or Config modes on master or local controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show auth-tracebuf | 911...
Page 912: Show Banner
Command History This command was available in ArubaOS 3.0. Command Information Licensing Command Mode Platforms All platforms Base operating system Config or Enable mode on master or local controllers 912 | show banner Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 913: Show Boot
Command History This command was available in ArubaOS 1.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Config or Enable mode on master or local controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show boot | 913...
Page 914 Default cellular priority: The output of this command includes the following parameters: Parameters Description Name of a cellular profile. Name Vendor ID in hexadecimal Vend 914 | show cellular profile Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 915 Send SCSI CDROM rezero command. Command History Introduced in ArubaOS 3.4. Command Information Platforms Licensing Command Mode 600 Series Base operating system Config or Enable mode on master or local controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show cellular profile | 915...
Page 916: Show Clock
Command History This command was available in ArubaOS 1.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Config or Enable mode on master or local controllers 916 | show clock Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 917 IPsec key for communication between the cluster member cluster member and the controller’s cluster root. controllers Command History This command was introduced in ArubaOS 5.0. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show cluster-config | 917...
Page 918 Command Information Platforms Licensing Command Mode All platforms Base operating system Enable mode on cluster member or cluster root controllers 918 | show cluster-config Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 919 This command sets the controller as a control plane security cluster Config mode on member, and defines the IPsec key for communication between the cluster member cluster member and the controller’s cluster root. controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show cluster-switches | 919...
Page 920 Command History This command was introduced in ArubaOS 5.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable mode on cluster member or cluster root controllers 920 | show cluster-switches Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 921 ..Command History This command was available in ArubaOS 3.0. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show command-mapping | 921...
Page 922 Command Information Platforms Licensing Command Mode All platforms Base operating system Config or Enable mode on master or local controllers 922 | show command-mapping Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 923: Show Configuration
Command History This command was available in ArubaOS 1.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Config or Enable mode on master or local controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show configuration | 923...
Page 924 Command History This command was available in ArubaOS 3.4 Command Information Platforms Licensing Command Mode All platforms Base operating system Config or Enable mode on master or local controllers 924 | show controller-ip Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 925 Command History This command is introduced in ArubaOS 6.1 Command Information Platforms Licensing Command Mode All platforms Base operating system Config or Enable mode on master or local controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show controller-ipv6 | 925...
Page 926 Command History This command was introduced in ArubaOS 5.0. Command Information Platforms Licensing Command Mode All platforms Base operating system. Enable mode on master or local controllers 926 | show control-plane-security Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 927 Command History This command was available in ArubaOS 1.0. Command Information Licensing Command Mode Platforms All platforms Base operating system Config or Enable mode on master or local controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show country | 927...
Page 928 Command History This command was introduced in ArubaOS 3.4 Command Information Platforms Licensing Command Mode All platforms This command requires the PEFNG Config mode on master controllers license. 928 | show cp-bwcontracts Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 929: Show Cpuload
Syntax Parameter Description current Include this optional parameter at the request of Dell technical support to display additional CPU troubleshooting statistics. Example This example shows that the majority of the controller’s CPU resources are not being used by either application (user) or system processes.
Page 930 Tunnel Trusted (Y/N): N Forced NAT-T (Y/N): N Related Commands Command Description Mode crypto-local ipsec-map Use this command to configure IPsec mapping for site- Config mode to-site VPN. 930 | show crypto-local ipsec-map Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 931 The output of this command displays the configured IKE version. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master or local controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show crypto-local ipsec-map | 931...
Page 932 This command was introduced in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master or local controllers 932 | show crypto dp Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 933 Use this command to configure a dynamic map. Config mode Command History Version Modification ArubaOS 3.0 Command introduced. ArubaOS 6.1 The output of this command displays the configured IKE version. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show crypto dynamic-map | 933...
Page 934 Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master or local controllers 934 | show crypto dynamic-map Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 935: Show Crypto Ipsec
= { Transport, Tunnel } Transform set default-rap-transform: { esp-aes256 esp-sha-hmac } will negotiate = { Transport, Tunnel } Transform set default-remote-node-bm-transform: { esp-3des esp-sha-hmac } will negotiate = { Transport, Tunnel } Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show crypto ipsec | 935...
Page 936 This command was introduced in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master or local controllers 936 | show crypto ipsec Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 937 The command show crypto isakmp stats shows the IKE statistics. (host) #show crypto isakmp stats Default protection suite 10001 Version 1 encryption algorithm: 3DES - Triple Data Encryption Standard (168 bit keys) Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show crypto isakmp | 937...
Page 938 This command was introduced in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master or local controllers 938 | show crypto isakmp Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 939 Server certificate name CA certificate name ----------------------- ------------------- (host) #show crypto-local isakmp dpd DPD is Enabled: Idle-timeout = 22 seconds, Retry-timeout = 2 seconds, Retry-attempts = 3 Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show crypto-local isakmp | 939...
Page 940 Use this command to assign the server certificate used Config mode to authenticate the controller for VPN clients. crypto-local isakmp xauth Use this command to enable the IKE XAuth for VPN Config mode clients. 940 | show crypto-local isakmp Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 941 The show crypto-local isakmp certificate-group command was introduced. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master or local controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show crypto-local isakmp | 941...
Page 942 If this information is not present, then the responder always holds up to date status information. Shows the name, original filename, reference count and expiration status of this IntermediateCA certificate. 942 | show crypto-local pki Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 943 TrustedCA parameter in this table. Shows trusted CA certificate information. This certificate can be either a root CA TrustedCA or intermediate CA. Dell encourages (but does not require) an intermediate CA’s signing CA to be the controller itself. <name> ALL Shows the version, signature algorithm, issuer, last update, next update, and CRL extensions and all other attributes of this certificate.
Page 944 SSL server CA : No Netscape SSL server : No Netscape SSL server CA : No S/MIME signing : No S/MIME signing CA : No S/MIME encryption : No 944 | show crypto-local pki Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 945 Command introduced. ArubaOS 6.1 The following parameters were introduced: Intermediate CA OCSPResponderCert OCSPSignerCert global-ocsp-signer-cert service-ocsp-responder Command Information Platforms Licensing Command Mode All platforms Base operating system Enable mode Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show crypto-local pki | 945...
Page 946: Show Crypto Map
Tunnel Trusted (Y/N): Y Forced NAT-T (Y/N): N Related Commands Command Description Mode crypto map global-map Use this command to configure the default global map. Config mode 946 | show crypto map Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 947 The output of this command displays the configured IKE version for the map. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master or local controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show crypto map | 947...
Page 948 49:90:47:f5:2f:e6:4e:dc:c3:06:7e:d2:51:29:ec: 52:8c:40:26:de:ae:c6:a0:21:1b:ee:46:b1:7a:9b: dd:0b:67:44:48:66:19:ec:c7:f4:24:bd:28:98:a2: c7:6b:fb:b6:8e:43:aa:c7:22:3a:b8:ec:9a:0a:50: c0:29:b7:84:46:70:a5:3f:09 Exponent: 65537 (0x10001) Attributes: a0:00 Signature Algorithm: sha1WithRSAEncryption 25:ce:0f:29:91:73:e9:cd:28:85:ea:74:7c:44:ba:b7:d0:5d: 2d:53:64:dc:ad:07:fd:ed:09:af:b7:4a:7f:14:9a:5f:c3:0a: 8a:f8:ff:40:25:9c:f4:97:73:5b:53:cd:0e:9c:d2:63:b8:55: a5:bd:20:74:58:f8:70:be:b9:82:4a:d0:1e:fc:8d:71:a0:33: bb:9b:f9:a1:ee:d9:e8:62:e4:34:e4:f7:8b:7f:6d:3c:70:4c: 4c:18:e0:7f:fe:8b:f2:01:a2:0f:00:49:81:f7:de:42:b9:05: 59:7c:e4:89:ed:8f:e1:3b:50:5a:7e:91:3b:9c:09:8f:b7:6b: 98:80 -----BEGIN CERTIFICATE REQUEST----- MIIB1DCCAT0CAQAwgZMxCzAJBgNVBAYTAlVTMQswCQYDVQQIEwJDQTESMBAGA1UE 948 | show crypto pki Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 949 This command was introduced in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master or local controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show crypto pki | 949...
Page 950 Command History Release Modification ArubaOS 3.0 Command introduced Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or config mode on master and local controllers 950 | show database Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 951 [counters|mac <macaddr>|table] tcp {app <app>|counters|tunnel} tunnel [counters|ipv4|ipv6|station-list|table] user {ap-name <ap-name>|counters|ip-addr <ip-address>|ipv4|ipv6|table} utilization vlan {ap-name <ap-name>}|{ip-addr <ip-address>|table} vlan-mcast wifi-reassembly counters wmm counters Descriptions Displays system statistics for your controller. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show datapath | 951...
Page 952 Dell technical support. performance Datapath performance counters. By default, combined statistics of all CPUs are shown. Packet trace buffer statistics. pkttrace-buffer Debug trace-buffer tables are displayed. trace-buffer 952 | show datapath Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 953 Displays ip-fragment statistics including CPU, current entries, high water mark, max , total, and aged entries. Displays IPv4 fragment statistics. ipv4 Displays IPv6 fragment statistics. ipv6 Hardware counters. counters statistics Hardware packet statistics. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show datapath | 953...
Page 954 Displays port link up and link down event counters. Displays the monitor port configuration. monitor Displays the physical port statistics. stats <slot/port> Displays the physical port status. status <slot/port> 954 | show datapath Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 955 Displays route cache table entries such as IP, mask, gateway, cost, VLAN and table flags. Displays all detailed route cache table entries including IP, mask, gateway, cost, verbose VLAN, flags, Internal VerNum Index. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show datapath | 955...
Page 956 Displays all the IP flows of a wireless device or Dell AP. Statistics include table entries including source IP, destination IP, protocol, SPort, DPort, Cntr, priority, ToS, age, destination, TAge and flags.
Page 957 Use the show datapath command to display various datapath statistics for debugging purposes. Example The following example displays a partial list of cyrpto parameter statistics. .(host) (config) #show datapath crypto counters Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show datapath | 957...
Page 958 The ipv6 filter option is added to the following parameters in the command: session tunnel user route-cache route ip-reassembly 958 | show datapath Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 959 Dell technical support. The firewall-agg-sess parameter is introduced. ArubaOS 6.2 Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or Config mode on master or local controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show datapath | 959...
Page 960 The IP address configured in the alias. This can be a network address, host address or a IP addr range. Network mark or the IP address range. Mask/Range 960 | show destination Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 961 Command Information Platforms Licensing Command Mode All platforms You must have a PEFNG license to Enable or Config mode on master and local configure or view a destination. controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show destination | 961...
Page 962 AT+CGDCONT=1,"IP","ISP.CINGULAR" ATD*99# Command History Introduced in ArubaOS 3.4. Command Information Platforms Licensing Command Mode W-600 series controllers Base operating system Config mode on master and local controllers 962 | show dialer group Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 963: Show Dir
Command History This command was introduced in ArubaOS 3.4. Command Information Platforms Licensing Command Mode W-600 series controllers Base operating system Config mode on master and local controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show dir | 963...
Page 964 Number of stations associated with the specified AP Stations Forwarding mode used by the specified AP Forwarding Mode AP profile Profile Number of ACLs this AP belongs to 964 | show dot1x ap-table Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 965 Command History This command was introduced in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show dot1x ap-table | 965...
Page 966 Command History This command was introduced in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or config mode on master controllers 966 | show dot1x ap-table aes Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 967 Command History This command was introduced in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show dot1x ap-table dynamic-wep | 967...
Page 968 Command History This command was introduced in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or config mode on master controllers 968 | show dot1x ap-table static-wep Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 969 Command History This command was introduced in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show dot1x ap-table tkip | 969...
Page 970 Key Exchange Failures..602 WPA2 Message-1......2630 Message-2......13 Message-3......13 Message-4......13 Rx Failed......2079 IE Mismatches....4158 Key Exchange Failures..549 Radius Accept......1217 Station Deauths....1151 The output of this command includes the following parameters: 970 | show dot1x counters Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 971 Number of key exchange failures Failures Radius Number of RADIUS accepts Accept Station Deauths Number of stations deaths Command History This command was introduced in ArubaOS 3.0. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show dot1x counters | 971...
Page 972 Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or config mode on master controllers 972 | show dot1x counters Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 973 ID of the last radius request Length of the last radius request ID of the last radius response The output of this command includes the following parameters: Parameter Description Name Supplicant name. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show dot1x supplicant-info | 973...
Page 974 Number of WPA group message-1s sent. WPA-GKey Message2 Number of WPA group message-2s sent. ID of the last EAP request The ID of the last EAP request. 974 | show dot1x supplicant-info Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 975 Command History This command was introduced in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show dot1x supplicant-info | 975...
Page 976 Command History This command was introduced in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or config mode on master controllers 976 | show dot1x supplicant-info list-all Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 977 Command History This command was introduces in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show dot1x supplicant-info pmkid | 977...
Page 978 Number of negative-acknowledgement characters sent by the supplicant. Supp-Naks UKeyRotations Number of unicast key rotations. Number of multicast key rotations. MKeyRotations Command History This command was introduced in ArubaOS 3.0. 978 | show dot1x supplicant-info statistics Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 979 Command Information Platforms Licensing Command Mode All platforms Base operating system Enable or config mode on master controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show dot1x supplicant-info statistics | 979...
Page 980: Usage Guidelines
This command allows you to test all of the enabled Config mode on master or local controllers. rule-test parser rules. Command History This command was introduced in ArubaOS 2.5. 980 | show esi groups Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 981 Command Information Platforms Licensing Command Mode All platforms Base operating system Enable and Config mode on master or local controllers. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show esi groups | 981...
Page 982 Config mode on master or local controllers. ESI syslog parser rule. esi parser rule-test This command allows you to test all of Config mode on master or local controllers. the enabled parser rules. 982 | show esi parser Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 983 This command was introduced in ArubaOS 3.1. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable and Config mode on master or local controllers. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show esi parser | 983...
Page 984 Number of ESI groups to which this set of ping attributes is assigned. Num Groups Related Commands Platforms Licensing Command Mode esi ping This command specifies the ESI ping Config mode on master or local controllers. health check configuration. 984 | show esi ping Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 985 This command was introduced in ArubaOS 2.5. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable and Config mode on master or local controllers. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show esi ping | 985...
Page 986 PU:Untrusted Ping response outstanding HT:Health Check Trusted IP HU:Health Check Untrusted IP FT:Trusted Ping failed FU:Untrusted Ping failed The output of this command includes the following information: 986 | show esi servers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 987 This command was introduced in ArubaOS 2.5. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable and Config mode on master or local controllers. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show esi servers | 987...
Page 988 Command History This command was introduced in ArubaOS 6.2. Command Information Licensing Command Mode Platforms All platforms Base operating system Config or Enable mode on master or local controllers 988 | show fast-roaming-r1-efficiency Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 989 All authentication servers in server group sg-auth2 are brought back in service. 2009-03-02 18:13:09 Authentication Server corp1-supersvr is down. 2009-03-02 18:13:09 All authentication servers in server group sg-auth2 are brought back in service. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show faults | 989...
Page 990 Command History This command was introduced in ArubaOS 3.0. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable and Config mode on master or local controllers. 990 | show faults Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 991: Show Firewall
Prohibit ARP Spoofing Disabled Stateful VOCERA Processing Enabled Stateful UA Processing Enabled Enforce bw contracts for broadcast traffic Disabled Multicast automatic shaping Disabled Enforce TCP Sequence numbers Disabled Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show firewall | 991...
Page 992 Shows if the controller allows three-way session when performing Allow tri-session with DNAT destination NAT. Disable FTP server If active, this feature disables the FTP server on the controller. 992 | show firewall Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 993 Layer-2 traffic. When this option is enabled, possible arp spoofing attacks are logged Prohibit ARP Spoofing and an SNMP trap is sent. Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show firewall | 993...
Page 994 Command History This command was introduced in ArubaOS 3.4. Command Information Platforms Licensing Command Mode All platforms Base operating system Enable and Config mode on master or local controllers 994 | show firewall Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 995 Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show firewall | 995...
Page 996 Command introduced. The IP Version parameter was added. ArubaOS Command Information Platforms Licensing Command Mode All platforms Base operating system Config or Enable mode on master or local controllers 996 | show firewall-cp Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 997 Platforms Licensing Command Mode W-3200, W-3400, W-3600, W- This command requires the PEFNG Config or Enable mode on master or local 6000M3, and W-7200 series license controller controllers Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide show firewall-visibility | 997...
Page 998 LMS. The cookie information on the LMS that is used to communicate with the master controller. LMS Cookies 998 | show gap-debug Dell PowerConnect W-Series ArubaOS 6.2 | Reference Guide...
Page 999 The length of the message that the master controller is syncing with the LMS. Attempts Number of times the master controller has attempted to sync with the LMS. Command History This command is introduced in Dell PowerConnect W-Series ArubaOS 6.2. Command Information Platforms Licensing...
Page 1000 Display the current status of the gateway health-check feature. Syntax No parameters. Usage Guidelines The gateway health check feature can only be enabled by Dell Technical Support. Example This example below shows that the gateway health-check feature has not been enabled on the controller. (host) #show gateway health-check...

This manual is also suitable for:

Powerconnect w-series

Dell PowerConnect W-7200 Series Reference Manual

Quick Links

Related Manuals for Dell PowerConnect W-7200 Series

Summary of Contents for Dell PowerConnect W-7200 Series

This manual is also suitable for:

Table of Contents