Table of Contents
Advertisement
SETTING UP YOUR VCR/DVD COMBINATION
Playing Dolby Digital (5.1 channel), DTS or MPEG audio
Connecting an amplifier with a Dolby Digital/ DTS/ MPEG Audio digital surround processor to your VCR/DVD's coaxial digital
jack provides richer and more powerful audio play.
C C Digital connection to a processor or amplifier with a coaxial digital input jack
You can make this connection using a coaxial digital cable.
NOTES:
• This connection is not possible if the processor or amplifier to which you want to connect does not have a coaxial digital
input jack.
• ANALOG AUDIO OUT and AV (TV) of the VCR/DVD are not available on the DTS audio.
VCR/DVD SET UP
Video Channel Setting
Video Channel setting will be necessary, if your VCR/DVD is
connected to the TV via the round coaxial cable.
1
Press VCR.
2
Insert a pre-recorded tape into the cassette compart-
ment.
Playback will start automatically.
If playback does not start, press PLAY.
3
Select and adjust your TV to channel 35.
• If the playback picture appears on the TV screen, con-
tinue with step
9
.
• If channel 35 is set for broadcasting, or interference
lines appear on the picture, the RF converter must be
set to a different channel between CH22 and CH69.
Continue with step
4
Press MENU.
5
Press K or L repeatedly to select INITIAL, then press B.
6
Press K or L repeatedly to select RF OUT, then press B.
The RF OUT CH menu will appear.
7
Press K or L to select a channel which is not used for
broadcasted between channel 22 and channel 69 in your
area, and B to confirm.
8
Press MENU to exit.
Set the TV channel to the RF OUT CHANNEL which was
selected on the VCR/DVD. A picture from the VCR/DVD
will appear on the TV screen. If a picture does not
appear, repeat steps
which is not used for broadcasting.
9
Press STOP to stop the tape.
NOTES:
• You may also access the RF OUT CH menu by pressing
and holding MENU on the remote control for 3 seconds
during power off until the RF OUT CH menu appears.
DVD
DIGITAL
ANALOG
AUDIO OUT
AUDIO OUT
COAXIAL
To COAXIAL
DIGITAL AUDIO
OUT jack
4
to
using a different channel
4
8
S-VIDEO
OUT
VCR
AV2 (DECODER)
L
DVD/VCR
AV1 (TV)
R
Coaxial digital cable
(commercially available)
DIGITAL IN
COAXIAL
To coaxial digital
input jack
• If this unit and your TV are connected using a SCART
cable, the RF converter may be switched off to avoid any
possibility of interference. To switch off the RF converter,
follow steps
edly until "--" appears next to "RF OUT CH". Press B,
then press MENU to exit.
Setting the Clock
This VCR/DVD incorporates a 24-hour clock. The clock must
be set for the Timer Recording function to operate correctly.
1
Press VCR, then MENU.
2
Press K or L to select INITIAL, then press B.
3
Press K or L to select CLOCK, then press B.
4
Press K or L to select MANUAL or AUTO, then press B.
• If you select MANUAL, continue with step
• If you select AUTO, Auto Clock Setting becomes "ON".
The clock time will appear automatically when you next
turn the VCR mode off and on.
5
Press K or L until the relevant year appears, then press B.
6
Press K or L until the relevant month appears, then
press B.
7
Press K or L until the relevant day appears, then press B.
8
Press K or L until the relevant hour appears, then press B.
9
Press K or L until the relevant minute appears.
10
Press MENU to start the clock.
NOTES:
• Press s to go one step back from the current step
during steps
• Although seconds are not displayed, they begin count-
ing from 00 when you exit by pressing the MENU. Use
this feature to synchronise the clock with the correct
time.
• If this unit is unplugged or if there is a power failure for
more than 1 hour, you may have to reset the clock.
– 12 –
AERIAL
RF OUT
Dolby Digital (5.1 ch) /
DTS / MPEG Audio
processor or amplifier
and
to
above and press L repeat-
1
4
6
5
to
9
.
5
.
EN
Advertisement
Table of Contents
