Table of Contents
Advertisement
One-touch Timer Recording (OTR)
The One-touch Timer Recording feature provides a
simple and convenient way to make a timed recording.
Example: One-touch Timer Recording for 30 minutes.
1
Load a cassette tape with the erase prevention tab
intact.
The unit will automatically turn on.
2
Press SPEED to select the desired tape speed SP or
SLP.
The tape counter and SP or SLP will appear on the
screen for about 4 seconds.
3
Set the TV/CABLE option to the appropriate position.
4
Press Number keys or CH
to be recorded.
5
Press REC. Press the button again to stop recording after
30 minutes. Each additional press of REC will increase
recording time as shown in the chart below, up to a
maximum of 6 hours. The OTR and recording time will
appear on the screen for about 4 seconds. And, REC will
keep blinking in the display.
Press
Recording time Press
once
NORMAL REC
twice
0:30
1:00
3 times
4 times
1:30
5 times
2:00
To cancel OTR
Press STOP or turn off the power.
"
" will appear on screen for about 4 seconds.
NOTE:
If you wish to watch the DVD playback during the OTR, press
DVD/VCR to change to DVD mode and perform the DVD
playback (see page 24).
20
/
to select the channel
Recording time
3:00
6 times
7 times
4:00
5:00
8 times
6:00
9 times
10 times
NORMAL REC
Timer recording
Timer recording can be programmed on-screen with the
remote control. The built-in timer allows automatic
unattended recording of up to 8 programs within 1 month.
Example: Program a timer recording for the 26th day,
channel 125 (CABLE), 11:00 - 11:30 PM on timer program
number 1 (Tape speed: SLP).
1
Press VCR MENU. Select
the "TIMER REC SET"
option, then press ENTER.
2
Press SET + or – to select
one of the program line,
then press ENTER.
3
Press SET + or – to select
the date, then press
ENTER.
4
Set the start time, end time,
channel and tape speed as
in step 3.
NOTES:
• Press CANCEL to move cursor backward for correction.
• To record from external source set the channel to "L". "L"
will appear next to CH 125 (or 69).
5
To enter other programs, repeat step 2 through 4.
• To return to the normal screen, press VCR MENU twice.
6
Press TIMER REC. The clock symbol(
display and the VCR stands by for recording. At the same
time, VCR mode will change to DVD mode automatically.
You can use DVD even if the VCR is in the Timer recording
mode.
If you do not use the DVD, turn the power off.
The timer recording will start at 20 seconds before the time
you predetermined.
NOTES:
• If the clock symbol (
in spite of the pressing of TIMER REC, the cassette may
not have been loaded yet. (see page 17)
• If the cassette is ejected in spite of the pressing of TIMER
REC, the erase prevention tab of the cassette may have
been removed. (see page 17)
NOTES:
• If the clock symbol (
ended, the TV program has not been completely recorded
because of an insufficient tape supply. Press TIMER REC to
cancel the timer program or press VCR EJECT to remove the
cassette tape.
• During timer recording standby mode, the VCR mode cannot
be selected. To use the VCR, press TIMER REC at first,
then press DVD/VCR to change to VCR mode. After you
use the VCR, press TIMER REC again to put the VCR into
timer recording standby mode.
• If you press TIMER REC during timer recording, the recording
operation will be interrupted. If you press TIMER REC
again within the programmed time, the recording operation
will start again.
• After a power failure or disconnection of the power plug, all
programmed recording settings and time display will be lost
upon resumption of power. In this case, reset the clock
(see page 16) and reprogram any timer recordings.
MENU
TIMER REC SET
AUTO REPEAT
ON OFF
SAP
ON OFF
CH SETUP
SYSTEM SETUP
+/-/ENTER/MENU
á
ñ
DATE
START END
26(SU) 11:00
11:30
PM
+/-/ENTER/CANCEL/MENU
á
) will appear on the
) does not appear on the display
) blinks when the timer recording
CH
125
PM
SLP
ñ
Advertisement
Table of Contents
