Specifications - Panasonic DLP PT-DZ570E Overview

Specifications

PT-DZ570E
Model
Power supply 100 – 240 V AC, 5.0 –1.9 A, 50/60 Hz
Power consumption 415 W (500 VA) (0.3 W at 100 –120 V AC, 0.4 W at 220 –240 V AC with standby mode set to ECO*
DLP™ chip 17.0 mm (0.67 inches) diagonal
( 16:10 aspect ratio )
DLP™ chip × 1, DLP™ projection system
2,304,000 (1,920 × 1,200) pixels
Lens Manual zoom (2× zoom), manual focus F 2.0 – 3.4, f 21.5 – 43.0 mm
Lamp 300 W (max 310 W) UHM lamp
Screen size (diagonal) 1.02–7.62 m (40 – 300 inches), 16:10 aspect ratio
Brightness* 2 4,000 lm (lamp mode: NORMAL)
Centre-to-corner uniformity* 2 90%
2
Contrast* 2,000:1 (full on/full off)
Resolution 1,920 × 1,200 pixels
Scanning HDMI/DVI-D f : 27 kHz–100 kHz; f
H
frequency RGB f : 15 kHz–100 kHz; f
H
YP P (YC C ) f : 15.75 kHz; f : 60 Hz (480i [525i])
B R B R H V
f : 31.50 kHz; f : 60 Hz (480p [525p])
H V
f : 15.63 kHz; f : 50 Hz (576i [625i])
H V
f : 31.25 kHz; f : 50 Hz (576p [625p])
H V
f : 37.50 kHz; f : 50 Hz (720 [750]/50p)
H V
Video/S-Video f : 15.75 kHz; f : 60 Hz (NTSC/NTSC4.43/PAL-M/PAL60), f
H V
Optical axis shift Vertical +60% from centre of screen (manual)
Horizontal ±10% from centre of screen (manual)
Keystone correction range Vertical: ±40°
Installation Ceiling/floor, front/rear
Terminals HDMI IN HDMI 19-pin × 1 (Deep Colour, compatible with HDCP)
480p, 576p, 720/60p, 720/50p, 1080/60i, 1080/50i, 1080/24p, 1080/24sF, 1080/25p, 1080/30p, 1080/60p, 1080/50p,
VGA (640 × 480) – WUXGA (1,920 × 1,200)*
Audio signal: linear PCM (sampling frequencies: 48 kHz, 44.1 kHz, 32 kHz)
DVI-D IN DVI-D 24-pin × 1 (DVI 1.0 compliant, compatible with HDCP, compatible with single link only)
480p, 576p, 720/60p, 720/50p, 1080/60i, 1080/50i, 1080/24p, 1080/24sF, 1080/25p, 1080/30p, 1080/60p, 1080/50p,
VGA (640 × 480) – WUXGA (1,920 × 1,200)*
RGB 1 IN BNC × 5 (RGB/YP P
B
RGB 2 IN D-sub HD 15-pin (female) × 1 (RGB/YP
VIDEO IN BNC × 1 (composite video)
S-VIDEO IN Mini DIN 4-pin × 1 (S-Video)
AUDIO IN 1 RCA × 2 (L, R × 1), 0.5 Vrms
AUDIO IN 2 M3 × 1 (L, R × 1), 0.5 Vrms
AUDIO IN 3 M3 × 1 (L, R × 1), 0.5 Vrms
AUDIO OUT M3 × 1 (L, R × 1) (monitor out: 0 – 2.0 Vrms, variable)
SERIAL IN D-sub 9-pin (female) × 1 for external control (RS-232C compliant)
REMOTE IN D-sub 9-pin (female) × 1 for external control (contact control)
LAN RJ-45 × 1 (for network connection, 10Base-T/100Base-TX, compliant with PJLink™)
Cabinet materials Moulded plastic (PC+ABS)
4
Dimensions (W x H x D) 332 × 168* × 484.5 mm (13-1/16˝ × 6-5/8˝ *
Weight Approximately 8.5 kg (18.7 lbs.)
Operating environment Operating temperature: 0°C – 45°C (32°F– 113°F); operating humidity: 20%–80% (no condensation)
Supplied accessories Power cord with security lock, wireless remote control unit, batteries for remote control (R6/LR6 type × 2), wire rope,
software CD-ROM (Logo Transfer Software, Multi Projector Monitoring & Control Software Ver. 2, Wireless Manager ME 5.5)
* 1 When the standby mode is set to ECO, network functions such as power on over the LAN will not operate. Also, only certain commands can be received for external control using
the serial terminal.
* 2 Measurement, measuring conditions and method of notation all comply with ISO 21118 international standards.
* 3 Compliant with VESA CVT-RB.
* 4 With legs at shortest position.
Terminals
1 2 3 4
N O T E S O N U S E
1. Do not install the projector in locations that are subject to excessive water, humidity, steam or oily smoke. Doing so may result in fire, mal-
function or electric shock.
2. The projector uses a high-voltage mercury lamp that contains high internal pressure. This lamp may break, emitting a large sound, or fail to
illuminate, due to impact or extended use.
3. The projector uses a high-wattage lamp that becomes very hot during operation. Please observe the following precautions:
• Never place objects on top of the projector while it is in operation.
• Make sure there is an unobstructed space of 500 mm (19-11/16 in) or more around the projector's exhaust openings.
• Do not stack projector units directly on top of one another for the purpose of multiple (stacked) projection.
When stacking projector units, be sure to provide the amount of space indicated between them. These space requirements also apply to
installation where only one projector unit is operating at one time and the other unit is used as a backup.
• If the projector is placed in a box or enclosure, the temperature of the air surrounding the projector must be between 0°C (32°F) and 40°C
(104°F). Also, make sure the projector's intake and exhaust openings are not blocked. Take particular care to ensure that hot air from the
exhaust openings is not sucked into the intake.
4. The lamp replacement cycle duration becomes shorter if the projector is operated repeatedly for short periods.
• The length of time that it takes for the lamp to break or fail to illuminate varies greatly depending on individual lamp characteristics and
usage conditions.
• The brightness of the lamp will gradually decrease with use.
5. Due to natural characteristics of lamps, screen brightness may vary (flicker). This is not an indication of faulty lamp performance.
Weights and dimensions shown are approximate. Specifications are subject to change without notice. This product may be subject to export
regulations. All other trademarks are the property of their respective trademark owners. Projection images simulated. DLP, DLP logo and DLP
Medallion logo are trademarks or registered trademarks of Texas Instruments. © 2010 Panasonic Corporation. All rights reserved.
PT-DW530E
16.5 mm (0.65 inches) diagonal
( 16:10 aspect ratio )
DLP™ chip × 1, DLP™ projection system
1,024,000 (1,280 × 800) pixels
1,280 × 800 pixels
(input signals that exceed this resolution will
be converted to 1,280 × 800 pixels)
: 24 Hz–120 Hz; dot clock: 25 MHz–162 MHz
V
: 24 Hz–120 Hz; dot clock: 162 MHz or lower
V
f : 45.00 kHz; f : 60 Hz (720 [750]/60p)
H V
f : 33.75 kHz; f : 60 Hz (1035/60i)
H V
f : 33.75 kHz; f : 60 Hz (1080 [1125]/60i)
H V
f : 28.13 kHz; f : 50 Hz (1080 [1125]/50i)
H V
f : 28.13 kHz; f : 25 Hz (1080/25p)
H V
: 15.63 kHz; f
H
+70% from centre of screen (manual)
±10% from centre of screen (manual)
3 ; compatible with non-interlaced signals only; dot clock: 25 –162 MHz
3 ; compatible with non-interlaced signals only; dot clock: 25 –162 MHz
× 1)
R
P × 1)
B R
4
× 19-1/16˝ ) (including the lens)
5 6
8 9 10 11 12
PT-DX500E
1 , 15 W with standby mode set to NORMAL)
17.8 mm (0.70 inches) diagonal
( 4:3 aspect ratio )
DLP™ chip × 1, DLP™ projection system
786,432 (1,024 × 768) pixels
1.02–7.62 m (40 –300 inches), 4:3 aspect ratio
4,500 lm (lamp mode: NORMAL)
1,024 × 768 pixels
(input signals that exceed this resolution will
be converted to 1,024 × 768 pixels)
f : 27.00 kHz; f : 24 Hz (1080/24p)
H V
f : 27.00 kHz; f : 48 Hz (1080/24sF)
H V
f : 33.75 kHz; f : 30 Hz (1080/30p)
H V
f : 67.50 kHz; f : 60 Hz (1080/60p)
H V
f : 56.25 kHz, f : 50 Hz (1080/50p)
H V
: 50 Hz (PAL/PAL-N/SECAM)
V
+60% from centre of screen (manual)
±10% from centre of screen (manual)
7
1. LAN connector 8. Audio 1 input
2. HDMI input 9. Audio 2 input
3. Video input 10. Audio 3 input
4. S-Video input 11. Audio output
5. RGB 1 input 12. Remote input
6. RGB 2 input 13. Serial input
7. DVI-D input
The photo shows the PT-DZ570E/DW530E.
Note that the DVI-D input terminal on the
PT-DX500E is located between the LAN
13
connector and the HDMI input.
Dimensions
332
(13-1/16)
Projection Distance
PT-DZ570E (16:10 aspect ratio; throw ratio: 1.45 – 2.94:1)
Projection size Projection distance
(diagonal)
Min Max
(wide) (telephoto)
1.02 m 1.23 2.51
40˝ (4.1)
1.52 m 1.87 3.79
60˝ (6.2)
2.03 m 2.51 5.07
80˝ (8.3)
2.54 m 3.15 6.34
100˝ (10.4)
3.81 m 4.75 9.53
150˝ (15.6)
5.08 m 6.35 12.73
200˝ (20.9)
7.62 m 9.55 19.11
300˝ (31.4)
PT-DW530E (16:10 aspect ratio; throw ratio: 1.53 – 3.09:1)
Projection size Projection distance
PT-DZ570 - E (16:10)
(diagonal)
Min Max
(wide) (telephoto)
1.02 m 1.29 2.64
(4.3)
40˝
1.52 m 1.96 3.98
60˝ (6.5)
2.03 m 2.64 5.32
80˝ (8.7)
2.54 m 3.31 6.66
100˝ (10.9)
3.81 m 4.99 10.01
150˝ (16.4)
5.08 m 6.67 13.36
200˝ (21.9)
7.62 m 10.03 20.07
300˝ (33.0)
PT-DX500E (4:3 aspect ratio; throw ratio: 1.51– 3.05:1)
Projection size Projection distance
PT-DW530 - E (16:10)
(diagonal)
Min Max
(wide) (telephoto)
1.02 m 1.20 2.46
40˝ (4.0)
1.52 m 1.82 3.70
60˝ (6.0)
2.03 m 2.45 4.95
80˝ (8.1)
2.54 m 3.08 6.20
(10.1)
100˝
3.81 m 4.64 9.32
150˝ (15.3)
5.08 m 6.21 12.44
200˝ (20.4)
7.62 m 9.34 18.68
300˝ (30.7)
PT-DX500 - E (4:3)
Optional Accessories
ET-PKD110H
Ceiling mount
bracket
for high ceilings
ET-LAD60A
ET-WM200E
Replacement lamp unit
Wireless module
ET-LAD60AW
Replacement lamp unit
(twin pack)
For more information about Panasonic projectors
http://panasonic.net/avc/projector
JQA-0443 EC98J2010
Factories of Systems Business Group have received ISO 14001:2004—
the Environmental Management System certification (except for third
parties' peripherals).
All information included here is valid as of November 2010.
PT-DZ570E1 Printed in Japan.
unit: millimetres (inches)
484.5
(19-1/16)
unit: metres (feet)
Height from edge
of screen to centre
of lens
-0.05 – 0.27
(8.2) (-0.2 – 0.9)
-0.08 – 0.40
(12.4) (-0.3 – 1.3)
-0.11 – 0.54
(16.6) (-0.4 – 1.8)
-0.14 – 0.67
(20.8) (-0.4 – 2.2)
-0.20 – 1.01
(31.2) (-0.7 – 3.3)
-0.27 – 1.35
(41.7) (-0.9 – 4.4)
-0.40 – 2.02
(62.6) (-1.3 – 6.6)
Height from edge
of screen to centre
of lens
-0.11 – 0.27
(8.6) (-0.4 – 0.9)
-0.16 – 0.40
(13.0) (-0.5 – 1.3)
-0.22 – 0.54
(17.4) (-0.7 – 1.8)
-0.27 – 0.67
(21.8) (-0.9 – 2.2)
-0.40 – 1.01
(32.8) (-1.3 – 3.3)
-0.54 – 1.35
(43.8) (-1.8 – 4.4)
-0.81 – 2.02
(65.8) (-2.7 – 6.6)
Height from edge
of screen to centre
of lens
-0.06 – 0.31
(8.0) (-0.2 – 1.0)
-0.09 – 0.46
(12.1) (-0.3 – 1.5)
-0.12 – 0.61
(16.2) (-0.4 – 2.0)
-0.15 – 0.76
(20.3) (-0.5 – 2.5)
-0.23 – 1.14
(30.5) (-0.8 – 3.8)
-0.31 – 1.52
(40.8) (-1.0 – 5.0)
-0.46 – 2.29
(61.2) (-1.5 – 7.5)
ET-PKD110S
Ceiling mount bracket
for low ceilings
051