Output Mode And Output Operation; Setting; Run Mode - Panasonic DP-100 series Instruction Manual

6

OUTPUT MODE AND OUTPUT OPERATION

The EASY mode, hysteresis mode or window comparator mode can be
selected as the output mode for comparative output 1 and comparative
output 2.
Refer to 'Comparative output 1/2 output mode setting' in '
SETTING MODE' for details.
EASY mode
ON / OFF of the comparative output is controlled in this mode.
P
0
ON
Comparative
output OFF
Notes:1) Hysteresis can be fixed in 8 steps.
Refer to <Hysteresis fixed value selection> in '
2 ' ' is displayed for comparative output 1 and '
on the sub-display .
Hysteresis mode
The comparative output ON / OFF state can be controlled with randomly
set hysteresis in this mode.
Hi
Lo
0
Comparative
ON
output
OFF
Note: ' ' or ' ' is displayed for comparative output 1 and '
comparative output 2 on the sub-display.
Window comparator mode
In this mode, the ON or OFF state of the comparative output is controlled
with a pressure in the set range.
Hi
Lo
0
Comparative
ON
output
OFF
Notes:1) Hysteresis can be fixed in 8 steps.
Refer to < Hysteresis fixed value selection> in '
2 ' ' or ' ' is displayed for comparative output 1 and '
comparative output 2 on the sub-display.
7

SETTING

<Setting procedures>

RUN MODE

This is the pressure detection state.
Refer to ' 8 RUN MODE'.
MODE
Press for 2 sec.
MODE
Press for 4 sec.
(Note)
Note: Although the menu setting mode appears two seconds after the mode selection
key is pressed, keep pressing the key.
9 9
H (Hysteresis)
H Hysteresis fixed (Note 1)
10 PRO MODE' for setting.
' for comparative output 2
H: 1 digit or more
H (Hysteresis)
2 digits or more when
using psi unit
' or '
H (Hysteresis)
H (Hysteresis)
H Hysteresis fixed (Note 1)
PRO MODE' for setting.
10
' or '
MENU SETTING MODE
This is the setting mode for simple
setting.
9
Refer to ' MENU SETTING MODE '.
PRO MODE
This is the setting mode for
detailed setting.
Refer to ' PRO MODE '.
10
8 RUN MODE
Setting the threshold value
Refer to 'Comparative output 1/2 output
mode setting' and 'Analog voltage output /
MENU
external input selection' in '
TING MODE' for setting conditions.
Since only the sub-display changes in the threshold setting, the following
shows only the sub-display.
Note: If the set pressure range is exceeded, '
(exceeds the lower limit) will appear on the sub-display.
' ' will also appear if the Hi side threshold value exceeds the Lo side threshold
value when setting the ' hysteresis mode / window comparator mode ' threshold value.
Standard type
<Setting condition 1>
Comparative output 1 output mode: '
Comparative output 2 output mode: '
<Setting condition 2>
Comparative output 1 output mode: '
Comparative output 2 output mode: '
' for
<Setting condition 3>
Comparative output 1 output mode: '
Comparative output 2 output mode: '
MODE
' for
<Setting condition 4>
Comparative output 1 output mode: '
Comparative output 2 output mode: '
<Setting condition 5>
Comparative output 1 output mode: '
Comparative output 2 output mode: '
MODE
<Setting condition 6>
Comparative output 1 output mode: '
Comparative output 2 output mode: '
MODE
9 9 MENU SET-
' (exceeds the upper limit) or '
' (EASY mode)
' (OFF)
<RUN mode state>
' (EASY mode)
' (EASY mode)
<RUN mode state>
Automatic
MODE
Automatic
' (EASY mode)
' (Hysteresis mode) or
' ' (Window comparator mode)
<RUN mode state>
Automatic
MODE
Automatic
MODE
Automatic
' (Hysteresis mode) or
' ' (Window comparator mode)
' (OFF)
<RUN mode state>
Automatic
MODE
Automatic
' (Hysteresis mode) or
' ' (Window comparator mode)
' (EASY mode)
<RUN mode state>
Automatic
MODE
Automatic
MODE
Automatic
' (Hysteresis mode) or
' ' (Window comparator mode)
' (Hysteresis mode) or
' ' (Window comparator mode)
<RUN mode state>
Automatic
MODE
Automatic
MODE
Automatic
MODE
Automatic
DP-100
'