Yamaha DSP-Z11 Owner's Manual page 87

Speakers (Speaker low-frequency effect level)
Select to adjust the speaker LFE level.
Headphones
(Headphone low-frequency effect level)
Select to adjust the headphone LFE level.
Note
Depending on the settings of "Bass Out" (see page 85), some signals may not be output
at the SUBWOOFER PRE OUT jacks.
■ Dynamic Range (Dynamic range)
Use this feature to select the amount of dynamic range compression
to be applied to your speakers or headphones. This setting is
effective only when the unit is decoding bitstream signals.
Speakers (Speaker dynamic range)
Adjusts the dynamic range compression for the speakers.
Headphones (Headphone dynamic range)
Adjusts the dynamic range compression for the headphones.
Choice
MAX Preserves the greatest amount of dynamic range.
STD Adjusts the dynamic range to medium. When this unit is
decoding Dolby TrueHD signals, the dynamic range
control is always active regardless of the instruction of
the input source signals.
MIN/AUTO • MIN: Adjusts the dynamic range to narrow when this
unit is decoding bitstream signals (except Dolby
TrueHD).
• AUTO: Adjusts the dynamic range according to the
instruction of the input source signals when this unit is
decoding Dolby TrueHD signals.
■ S-Wave Control (Standing wave control)
Use this menu to activate or deactivate the specially customized
parametric equalizer to reduce the effects of acoustic standing
waves in the listening room. See page 44 for details.
Choice
On Activates the parametric equalizer.
Off Deactivates the parametric equalizer.
■ Parametric EQ (Parametric equalizer)
Use this feature to adjust the parametric equalizer of each speaker.
PEQ Data Copy (Parametric equalizer data copy)
Use this feature to copy the result data of the automatic setup to the
manual configuration area. You can select the parametric equalizer
type applied to the copied result data of the automatic setup. See
page 46 for the descriptions of each parametric equalizer type.
Choice
Flat → Manual
Copies the result of the automatic setup that the "Flat"
type parametric equalizer is applied to.
Front → Manual
Manual Copies the result of the automatic setup that the
"Front" type parametric equalizer is applied to.
Natural → Manual
Copies the result of the automatic setup that the
"Natural" type parametric equalizer is applied to.
Functions
Functions
Descriptions
PEQ Select (Parametric equalizer type select)
Use this feature to select the parametric equalizer type that applied
to the results of the automatic setup. See page 46 for the
descriptions of each parametric equalizer type.
Choice
Manual Applies the manually configured parametric equalizer in
"Manual Setup".
Flat Applies the "Flat" type parametric equalizer.
Front Applies the "Front" type parametric equalizer.
Natural Applies the "Natural" type parametric equalizer.
Through Does not use the parametric equalizer.
Notes
• When you carry out the automatic setup, this unit automatically set "PEQ Select" to
"Natural".
• "Speaker Level" settings (see page 86) also changes corresponding to the setting of
"PEQ Select".
• This unit does not change the configurations of "Manual" even if you perform the
automatic setup.
Manual parametric equalizer configuration of each
speaker
Use this feature to adjust the tonal quality of each speaker. You can
copy the results of the automatic setup for the base of the manual
configuration by using "PEQ Data Copy". Set "PEQ Select" to
"Manual" in advanced.
1
Press 9 k / n / l / h to select "Test Tone" or the
speaker you want to adjust.
Choice
Front L Front left speaker
Front R Front right speaker
Center Center speaker
Surround L Surround left speaker
Surround R Surround right speaker
Surround Back L Surround back left speaker
Surround Back R Surround back right speaker
Front Presence L Front presence left speaker
Front Presence R Front presence right speaker
Rear Presence L Rear presence left speaker
Rear Presence R Rear presence right speaker
Subwoofer L Subwoofer left
Subwoofer R Subwoofer right
Test Tone
Use this feature to select whether to turn on or off the test tone
output while you are adjusting the tonal quality of each
speaker.
Choice
On Outputs the test tone.
Off Does not output the test tone.
Graphical user interface (GUI) menu
Descriptions
Adjusted speaker
Functions
87
En