Advertisement
Quick Links
Owner's Manual
IP
R
0
F E S
S
I
0
N A L I
318 in., 9.6 VOLTS PROFESSIONAL
CORDLESS DRILL-DRIVER
Variable Speed / Reversible
Model No.
315.273980
Save this manual
for
future reference
_,
CAUTION:
Read and
follow all Safety Rules and
Operating Instructions before
first use of this product.
Customer
Help Line:
1-800-932-3188
Sears,
Roebuck
and Co., Hoffman
Estates,
IL 60179
U
Visit the Craftsmen
web page: www.sears.com/craftsman
972000-809
1-01
• Safety
• Features
• Assembly
• Operation
• Maintenance
_l=,_,-List
®
Advertisement
Related Manuals for Craftsman 315.273980
Summary of Contents for Craftsman 315.273980
- Page 1 Safety Rules and • Features Operating Instructions before • Assembly first use of this product. • Operation • Maintenance Customer Help Line: 1-800-932-3188 _l=,_,-List ® Sears, Roebuck and Co., Hoffman Estates, IL 60179 Visit the Craftsmen web page: www.sears.com/craftsman 972000-809 1-01...
- Page 2 TABLE OF CONTENTS • General Safety Rules ..............................• Specific Safety Rules/Symbols ..........................• Features ..................................• Assembly ..................................• Operation .................................. 9-14 • Maintenance ................................• Accessories ................................. • Warranty ..................................• Exploded View And Repair Parts List ......................... •...
- Page 3 Tool Use end Care Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained tools, with sharp • Use clamps or other practical way to secure and cutting edges are less likely to bind and are easier to support the workpiece to a stable platform.
- Page 4 c. That wire size is large enough for AC ampere Important Safety Charger Instructions rating of charger as specified below: • Save these Instructions. This manual contains Cord Length (Feet) 100' important safety and operating instructions for battery charger part number 9-11040 (981399-001). Cord Size (AWG) Following this rule will reduce the risk of electric Note: AWG = American Wire Gage...
- Page 5 WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • lead from lead-based paints, • crystalline silica from bricks and cement and other masonry products, and •...
-
Page 6: Switch Lock
FORWARD/REVERSE SELECTOR KNOW YOUR DRILL-DRIVER (DIRECTION OF ROTATION SELECTOR) See Figure 1. Your driU-driver has a forward/reverse selector located Before attempting to use your drill-driver, familiarize yourself with all operating features and safety above the switch trigger. .requirements. WRIST STRAP A wrist strap is provided to reduce the chances of dropping WARNING: Carefully read through this entire owner's... - Page 7 TWO SPEED GEARTRAIN(HI-LO) ,___ SCREWDRIVER BITS KEYLESS CHUCK CHARGER YELLOWUGHT"ON" AND RED LIGHT FLASHINGINDICATES DEFECTIVEBATrERYPACK DIRECTIONOF ROTATIONSELECTOR (FORWARD/REVERSE) TORQUE ADJUSTMENT RING SWITCH TRIGGER BA'I3'ERY PACK RED LIGHT "ON" INDICATESFAST CHARGINGMODE GREENLIGHT "ON" INDICATESFULLY CHARGEDANDSLOWCHARGING TO MAINTAINBAI"rERYPACK WRISTSTRAP Fig. 1 CHARGER See Figure 2.
- Page 8 TO AI-I'ACH BA'I-I'ERYPACKTO DRILL TO REMOVE BATTERY PACK FROM DRILL See Figure 4. See Figure 3. • Lock the switch trigger by placing the direction of Note: Battery pack is shipped in a low charge condition. rotation selector in center position, See Figure 10. Therefore, it must be charged priorto use.
- Page 9 If after one hour red light is still flashing, this indicates a WARNING: Always wear safety goggles or safety defective battery pack and should be replaced. glasses with side shields when operating tools. Failure to do so could result in objects being thrown Green light on indicates battery pack is fully charged into your eyes, resulting in possible serious injury.
- Page 10 INSTALLINGBITS WARNING: Make insert drill bit straight into sure to See Figure 6. chuck Jaws."Do not insert drill bit into chuck jaws at an angle and then tighten, as shown in Figure 7. This • Lock the switch trigger by placing the direction of could cause drill bit to be thrown from drill, resulting in rotation selector in center position.
- Page 11 SWITCH LOCK SWITCH See Figure 10. See Figure 8. The switch trigger can be locked in the OFF position. This To turn your drill ON, depress the switch trigger. To turn it feature can be used to prevent the possibility of accidental OFF, release the switch trigger.
- Page 12 KEYLESSCHUCK ADJUSTABLE TORQUE CLUTCH See Figure 11. Your drill is equipped with an adjustable torque clutch for Your new drill has a keyless chuck. As the name implies, driving different types of screws into different materials. you can hand tighten or release drill bits in the chuck jaws. The proper setting depends on the type of material and Grasp and hold the collar of the chuck with one hand.
- Page 13 APPLICATIONS When drilling hard smooth surfaces use a center punch to mark desired hole location. This will prevent the drill bit (Use drill-driver only for the purpose listed below) from slipping off center as the hole is started. However, • Drilling in wood.
- Page 14 CHUCK REMOVAL Insert hex key wrench in chuck and tighten chuck jaws securely. Tap sharply with a mallet in a counter- See Figures 14, 15, and 16. clockwise direction. This will loosen chuck on the The chuck must be removed in order to use some spindle.
- Page 15 Do not abuse power tools. Abusive practices can WARNING: When servicing use only identical Craftsman replacement parts. Use of any other damage tool as well as workpiece. parts may create a hazard or cause product damage, Only the parts shown on parts list, page 17, are intended to be repaired or replaced by the customer.
- Page 16 Thefollowing recommended accessories a recurrently available at SearsRetail S tores. • 17-Pc. Power Screwdriver/Nutdriver Set and Case • 6-Pc. Extra Length Magnite Power Bit Set • High Speed Bits (For Wood or Metal)..3/4 in. Max, • 30-Pc. Power Screwdriver/Nutdriver Set and Case WARNING: The use of attachments or accessories not listed might be hazardous.
-
Page 17: Parts Orderinginstructions
DRILL-DRIVER MODEL NO. 315.273980 The model number will be found on a plate attached to the motor housing. Always mention the model number in all correspondence regarding your CRAFTSMAN 3/8 in., 9.6 VOLTS PROFESSIONAL CORDLESS DRILL-DRIVER or when ordering repair parts. - Page 18 For repair of major brand appliances in your own home... no matter who made it, no matter who sold it! 1-800-4-MY-HOME sM Anytime, day or night (1-800-469-4663) www.sears.com To bring in products such as vacuums, lawn equipment and electronics for repair, call for the location of your nearest Sears Parts & Repair Center. 1-800-488-1222 Anytime, day or night www.sears.com...