DO NOT SET THE PROJECTOR IN GREASY, WET, OR other area of the world. SMOKY CONDITIONS SUCH AS IN A KITCHEN TO PREVENT Your SANYO product is designed and A BREAKDOWN OR A DISASTER. IF THE PROJECTOR manufactured with high quality materials...
SAFETY INSTRUCTIONS All the safety and operating instructions should be read before This projector should be operated only from the type of power the product is operated. source indicated on the marking label. If you are not sure of the type of power supplied, consult your authorized dealer or Read all of the instructions given here and retain them for later local power company.
COMPLIANCES Federal Communication Commission Notice This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
TABLE OF CONTENTS FEATURES AND DESIGN COMPUTER INPUT SELECTING INPUT SOURCE SELECTING COMPUTER SYSTEM PREPARATION PC ADJUSTMENT AUTO PC ADJUSTMENT NAME OF EACH PART OF PROJECTOR MANUAL PC ADJUSTMENT PICTURE IMAGE ADJUSTMENT SETTING-UP PROJECTOR IMAGE LEVEL SELECT CONNECTING AC POWER CORD IMAGE LEVEL ADJUSTMENT LENS INSTALLATION PICTURE SCREEN ADJUSTMENT...
FEATURES AND DESIGN This Multimedia Projector is designed with most advanced technology for portability, durability, and ease of use. This projector utilizes built-in multimedia features, a palette of 1.07 billion colors, and matrix liquid crystal display (LCD) technology. ◆ Motor-driven Lens Shift ◆...
PREPARATION NAME OF EACH PART OF PROJECTOR FRONT OF CABINET INFRARED POWER CORD REMOTE RECEIVER CONNECTOR PROJECTION LENS (Option) MAIN ON / OFF LENS CAP SWITCH (Option) CAUTION CARRYING HANDLE Do not turn on a projector with lens cap LEVEL AND TILT ADJUST HANDLE attached.
PREPARATION SETTING-UP PROJECTOR CONNECTING AC POWER CORD This projector uses nominal input voltages of 120 V or 200-240 V AC. This projector automatically selects correct input voltage. It is designed to work with single- phase power systems having a grounded neutral conductor.
PREPARATION LENS INSTALLATION Before setting up a projector, install Projection Lens on a Projector. 1. Before installation, check where a projector is used and prepare suitable lens. For specifications of Projection Lens, refer to manual separately attached or contact sales dealer where you purchased a projector. 2.
PREPARATION PICTURE LEVEL AND TILT ADJUSTMENT REAR ADJUSTABLE Picture tilt and projection angle can be adjusted with FEET. (Refer to P7). handles on both sides of a projector. Projection angle can be adjusted to 5.7 degrees upper way. LEVEL AND TILT ADJUST HANDLE Press knob on handle.
PREPARATION MOVING PROJECTOR For safety, be sure to hold Carrying Handles CARRYING on both sides by 2 or more people when HANDLE moving a projector. Moving it unproperly may result in damage of cabinet or person's injury. Replace lens cap and retract feet to prevent damage to lens and cabinet.
CONNECTING PROJECTOR TERMINALS OF PROJECTOR This projector applies various input/output terminals and 4 terminal slots for expansion to tune to diversity of signals from computers and video equipment. 4-built-in Terminal Slots enable you to arrange desired combinations of input sources just by changing Terminal Boards.
Page 13
CONNECTING PROJECTOR INPUT/OUTPUT TERMINALS AND JACKS INPUT 2 INPUT 1 INPUT 1, 2, 3 DVI INPUT TERMINAL 5 BNC INPUT JACKS AUDIO INPUT JACKS Connect computer output Connect audio output Connect component video output (Cr, Y, Cb or Pr, Y, Pb) from video equipment to (Digital/Analog DVI-I type) to from computer or video equipment to these jacks.
Page 14
CONNECTING PROJECTOR USB PORT (Series B) SERIAL PORT IN TERMINAL This port is used to service this projector. If you control a projector by computer, Connect USB port of computer to this you must connect a cable (not provided) port. from your computer to this terminal.
CONNECTING PROJECTOR CONNECTING TO COMPUTER Cables used for connection ✽ = Cables are not supplied with this projector.) • VGA Cable (HDB 15 pin) NOTE : • DVI Cable ✽ When connecting cable, power cords of both a ✽ • BNC Cable (BNC x 5) projector and external equipment should be •...
BEFORE OPERATION SIDE CONTROLS AND INDICATORS REAR INDICATORS SIDE CONTROLS FRONT INDICATORS SIDE CONTROLS POWER ON–OFF BUTTON ZOOM BUTTONS FOCUS BUTTONS Used to adjust focus. (P24) Used to turn a projector on Used to adjust zoom. or off. (P23) (P24) ZOOM FOCUS ON-OFF...
Page 18
BEFORE OPERATION INDICATORS FRONT INDICATORS LAMP READY WARNING TEMP. LAMP REPLACE LAMP REPLACE INDICATOR LAMP INDICATOR WARNING TEMP. INDICATOR READY INDICATOR This indicator flashes red This indicator lights green This indicator is dim when a This LAMP REPLACE projector is turned on. And when internal projector when a projector is ready to indicator lights yellow when...
BEFORE OPERATION OPERATION OF REMOTE CONTROL AUTO PC ADJ. BUTTON POWER ON-OFF BUTTON LIGHT BUTTON Used to operate AUTO PC Used to turn projector on or Adjustment function. (P28) Lights the buttons on the remote off. (P23) control for about 10 seconds. NO SHOW BUTTON Used to turn picture into MENU BUTTON...
BEFORE OPERATION REMOTE CONTROL BATTERIES INSTALLATION Remove battery Slide batteries into Replace compartment lid. compartment lid. compartment. Two AA size batteries Pull up lid and For correct polarity (+ and remove it. –), sure battery terminals are in contact with pins in compartment. To insure safe operation, please observe following precautions : ●...
BEFORE OPERATION OPERATING ON-SCREEN MENU HOW TO OPERATE ON-SCREEN MENU REMOTE CONTROL UNIT You can control and adjust this projector through ON-SCREEN MENU. Refer to following pages to operate each adjustment on ON-SCREEN MENU. 1 DISPLAY MENU POINT BUTTONS Press MENU button to display ON-SCREEN MENU. Used to move a Pointer UP/ DOWN/ 2 MOVING POINTER...
BEFORE OPERATION MENU BAR FOR PC SOURCE Press MENU BUTTON while connecting to PC input source. IMAGE SELECT MENU SCREEN MENU Used to select Used to adjust size GUIDE WINDOW PC SYSTEM MENU image level among of image. [Normal Shows selected Used to select Standard, Real / True / Wide /...
BASIC OPERATION TURNING ON / OFF PROJECTOR TURNING ON PROJECTOR Complete peripheral connections (with Computer, VCR, etc.) before turning on projector. (Refer to "CONNECTING TO LAMP STATUS PROJECTOR" on Pages 13~16 for connecting that equipment.) INPUT 1 Connect a projector's AC Power Cord into a wall outlet and turn MAIN ON/OFF SWITCH to ON.
BASIC OPERATION ADJUSTING SCREEN ZOOM ADJUSTMENT Press ZOOM ▲/▼ button on Side Control or on Remote Control Unit. Message “Zoom” is displayed. Press ZOOM ▲ button to make image larger, and press ZOOM Zoom ▼ button to make image smaller. Message disappears after 4 seconds.
BASIC OPERATION PICTURE FREEZE FUNCTION Press FREEZE button on Remote Control Unit to freeze picture on-screen. To cancel FREEZE function, press FREEZE button again or press any other button except POINT UP/DOWN/LEFT/RIGHT and SELECT button. NO SHOW FUNCTION Press NO SHOW button on Remote Control Unit to black out a image. No show To restore to normal, press NO SHOW button again or press any other button except POINT UP/DOWN/LEFT/RIGHT and SELECT...
COMPUTER INPUT SELECTING INPUT SOURCE INPUT 1/2 button INPUT 3/4 button DIRECT OPERATION INPUT 1 INPUT 3 Select INPUT source by pressing INPUT 1/2, INPUT 3/4 or INPUT 1 - INPUT 4 buttons on Side Control or on Remote INPUT 2 INPUT 4 Control Unit.
COMPUTER INPUT WHEN SELECT INPUT 2 (5 BNC INPUT JACKS ) When connect a computer output [5 BNC Type (Red, Green, Blue, INPUT MENU Horiz. Sync and Vert. Sync.)] from a computer to R/Pr, G/Y, B/Pb, H/HV and V jacks. INPUT Menu icon Press MENU button and ON-SCREEN MENU will appear.
COMPUTER INPUT PC ADJUSTMENT AUTO PC ADJUSTMENT Auto PC Adjustment function is provided to automatically adjust Fine sync, Total dots and Picture Position to conform to your computer. Auto PC Adjustment function can be operated as follows. Auto PC Adj. Press MENU button and ON-SCREEN MENU will appear.
COMPUTER INPUT MANUAL PC ADJUSTMENT This projector can automatically tune to display signals from most personal computers currently distributed. However, some computers employ special signal formats which are different from standard ones and may not be tuned by Multi-Scan system of this projector.
Page 30
COMPUTER INPUT Display area Selects area displayed with this projector. Select resolution at Display area dialog box. Press SELECT button at Display area icon and Display Display area H area dialog box appears. Adjustment of horizontal area displayed with this projector. Press Display area POINT LEFT/RIGHT button(s) to decrease/increase value and then press SELECT button.
COMPUTER INPUT PICTURE IMAGE ADJUSTMENT IMAGE LEVEL SELECT (DIRECT) Select image level among Standard, Real, Image 1, Image 2, Image 3 IMAGE button and Image 4 by pressing IMAGE/IMAGE SEL. button on Side Control Standard or on Remote Control Unit. Real Standard Normal picture level preset on this projector.
COMPUTER INPUT IMAGE LEVEL ADJUSTMENT Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT buttons to move a red frame pointer to IMAGE ADJUST MENU IMAGE ADJUST Menu icon. Press POINT DOWN button to move a red frame pointer to item that you want to adjust and then press SELECT button.
COMPUTER INPUT PICTURE SCREEN ADJUSTMENT This projector has a picture screen resize function, which enables you to display desirable image size. Press MENU button and ON-SCREEN MENU will appear. Press SCREEN MENU POINT LEFT/RIGHT button(s) to move a red frame pointer to SCREEN Menu icon.
VIDEO INPUT SELECTING INPUT SOURCE INPUT 1/2 button INPUT 3/4 button DIRECT OPERATION INPUT 1 INPUT 3 Select INPUT source by pressing INPUT 1/2, INPUT 3/4 or INPUT 1 - INPUT 4 buttons on Side Control or on Remote INPUT 2 INPUT 4 Control Unit.
VIDEO INPUT SELECTING VIDEO SYSTEM Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT buttons to move a red frame pointer to AV SYSTEM Menu icon. Press POINT DOWN button to move a red arrow pointer to system that you want to select and then press SELECT button. Y, Pb/Cb, Pr/Cr JACKS AV SYSTEM MENU (COMPONENT VIDEO) Auto...
VIDEO INPUT PICTURE IMAGE ADJUSTMENT IMAGE LEVEL SELECT (DIRECT) Select image level among Standard, Cinema, Image 1, Image 2, IMAGE button Image 3 and Image 4 by pressing IMAGE/IMAGE SEL. button on Side Standard Control or on Remote Control Unit. Cinema Standard Normal picture level preset on this projector.
VIDEO INPUT IMAGE LEVEL ADJUSTMENT Press MENU button and ON-SCREEN MENU will appear. Press IMAGE ADJUST MENU POINT LEFT/RIGHT button(s) to move a red frame pointer to IMAGE ADJUST Menu icon. Press POINT DOWN button to move a red frame pointer to item that you want to adjust and then press SELECT button.
VIDEO INPUT Store To store adjustment data, move a red frame pointer to Store icon and press SELECT button. Image Level Menu will appear. Move a red frame pointer to Image Level 1 to 4 and then press SELECT button. Image Level Menu Other icons operates as follows.
SETTING SETTING MENU Press MENU button and ON-SCREEN MENU will appear. Press SETTING MENU POINT LEFT/RIGHT button(s) to move a red-frame pointer to SETTING icon. Press POINT DOWN button to move a red-frame pointer to item Set a red frame SETTING Menu icon pointer to item and that you want to set and then press SELECT button.
Page 40
SETTING Power management This function turns Projection Lamp off when this projector detects signal interruption and is not used for a certain period in order to reduce power consumption and maintain Lamp-life. (This projector is Time left until Lamp off. shipped with this function ON.) Power Management function operates to turn Projection Lamp off when input signal is interrupted and any button is not pressed over 5...
Page 41
SETTING Remote control Remote control This projector provides eight different remote control codes (Code 1-Code 8); the factory-set, initial code (Code 1) and the other seven codes (Code 2 to Code 8). This switching function prevents remote control interference when operating several projectors or video equipment at the same time.
APPENDIX MAINTENANCE WARNING TEMP. INDICATOR The Warning Temp. Indicator flashes red to let you know the internal temperature FRONT INDICATORS of the projector exceeds the normal level. If the temperature goes up further, the projector will be turned off automatically and the Ready indicator will go out. (The Warning Temp.
APPENDIX LAMP MANAGEMENT This Projector is equipped with 4 Projection Lamps to ensure brighter image and those lamps are controlled by Lamp Management Function. Lamp Management Function detects status of all lamps and shows status on screen or on LAMP REPLACE indicator.
APPENDIX LAMP REPLACEMENT When the life of the Projection Lamp of this projector draws to an end, the LAMP REPLACE indicator lights yellow. If this indicator lights yellow, replace the projection lamp with a new one promptly. FRONT INDICATORS REAR INDICATORS LAMP READY WARNING:...
APPENDIX ORDER REPLACEMENT LAMP Replacement Lamp can be ordered through your dealer. When ordering a Projection Lamp, give the following information to the dealer. ● Model No. of your projector PLC-XF42 ● Replacement Lamp Type No. POA-LMP49 (Service Parts No. 610 300 0862) LAMP REPLACE COUNTER Be sure to reset Lamp Counter when Lamp Assembly is replaced.
You can often correct operating problems yourself. If a projector fails to work properly, see "TROUBLESHOOT- ING" section on page 47. To correct failure, try "Solutions". If after following all operating instructions, you find that service is necessary, contact Sanyo Service Station or store where you purchased unit.
APPENDIX TROUBLESHOOTING Before calling your dealer or service center for assistance, check matters below once again. 1. Make sure you have connected a projector to your computer or video equipment as described in section "CONNECTING PROJECTOR" on pages 13 ~ 16. 2.
APPENDIX MENU TREE Computer Input/Video Input Go to System Input Input 1 RGB (Analog) RGB (Scart) RGB (PC Digital) RGB (AV HDCP) Input 2 Go to System Go to System Y, Pb/Cb, Pr/Cr Input 3 Go to System ✽N/A not applicable - - - Computer Input Image Select...
Page 49
APPENDIX Video Input Computer Input/Video Input Setting Language English System Auto German 1080i/60 French 1080i/50 Italian 1035i Spanish 720p Portuguese 575p Dutch 480p Swedish 575i Russian 480i Chinese Korean Image Select Standard Japanese Cinema Quit Image 1 Keystone Image 2 Blue back On/Off Image 3...
APPENDIX INDICATORS AND PROJECTOR CONDITION Check the Indicators for projector condition. Indicators Projector Condition LAMP WARNING READY LAMP REPLACE TEMP. green yellow The projector is OFF. (The MAIN switch OFF position or the AC Power Cord is unplugged.) The projector is READY to be turned on with the POWER ON- ✽...
APPENDIX COMPATIBLE COMPUTER SPECIFICATIONS Basically this projector can accept a signal from all computers with V, H-Frequency mentioned below and less than 230 MHz of Dot Clock. ON-SCREEN H-Freq. V-Freq. ON-SCREEN H-Freq. V-Freq. RESOLUTION RESOLUTION DISPLAY (kHz) (Hz) DISPLAY (kHz) (Hz) VGA 1 640 x 480...
APPENDIX When a input signal is digital from DVI terminal, refer to chart below. ON-SCREEN H-Freq. V-Freq. ON-SCREEN H-Freq. V-Freq. RESOLUTION RESOLUTION DISPLAY (kHz) (Hz) DISPLAY (kHz) (Hz) D-VGA 640 x 480 31.47 59.94 D-WXGA 8 1280 x 768 68.633 84.837 720 x 480 D-480p...
APPENDIX TECHNICAL SPECIFICATIONS Projector Type Multi-media Projector Dimensions 22.9" x 10" x 30.9" (581 mm x 252 mm x 783 mm) (W x H x D) Net Weight 80.3 lbs (36.5 kg) LCD Panel System 1.8" TFT Active Matrix type, 3 panels Panel Resolution 1024 x 768 dots Number of Pixels...
APPENDIX CONFIGURATIONS OF TERMINALS DVI-I TERMINAL (DIGITAL/ANALOG) This terminal accepts only Digital (TMDS) or Analog (RGB) output signal. Connect display output terminal of computer to this terminal with DVI cable (not supplied). Pin Configuration Analog Red Input C1 C2 Analog Green Input Analog Blue Input Analog Horiz.
LCD PROJECTOR LENS REPLACEMENT AND INSTALLATION PROCEDURES CAUTION When installing or replacing the Projection Lens, refer to this manual. For installation of the lens, use the parts designated in the manual. Do not use the installation manual and Light-Block Sheets in the lens package. Check the following parts supplied to this projector.
Page 58
LENS REPLACEMENT AND INSTALLATION PROCEDURE NOTE : The installation procedure and needed parts for lens installation depend on the type of the Projection Lens. Check the Model No. of the Projection Lens and be sure to install or replace the lens following procedure below.
Page 59
Remove Lens Cap on the rear (mounting side) of Projection Lens and mount Lens on the lens Attachment with 4 Screws. (Use screws attached on lens.) Connect the Lens Motor Lead connector to the socket on the right-top of the lens attachment. (Motor Driven Lens only.) See Fig.
Page 60
This projector has 6 Light-Block Sheets. Use 2 Light-Block Sheets corresponding with lens. (Refer to the list below.) Use 1 Light-block Sheet for MODEL LNS-W03 Set 2 Light-Block Sheets through the lens. Make sure the shape of the Light-Block Sheets are correct and be sure to set them as shown in the Fig. 8. NOTE: ●...
Page 61
Adjust focus of the Projection Lens. (LNS-W01, LNS-W01Z, LNS-T01, LNS-T01Z and LNS-W03 only.) Set up the projector and project image on the screen. Loosen Focus Lens Lock Screw and rotate Projection Lens to obtain proper focus. After adjusting focus, be sure to lock Projection Lens with Focus Lens Lock Screw securely.
Page 62
FOCUS ADJUSTMENT (For Model LNS-W03) Set up the projector and project image on the screen. 1. Loosen the Focus Lock Screw on the projection ● mark (yellow) lens. 2. Rotate the projection lens to obtain proper focus on center area of the screen. When the distance of the screen and lens is 1 meter, ●...
Correcting the focus When the lens is attached to the projector and images are being projected onto the screen, the peripheral focus may be out of focus in some localized areas. If this happens, insert the accessory in between the lens attachment and the lens to correct the focus. D’...