Pioneer HTP-3600 Quick Start Manual

HTP-3600 Quick Start Guide
Check that you have all the
1
accessories.
STANDBY/ON
SLEEP STATUS
Speaker cord (x6)
INPUT SELECTOR
DIGITAL STB DVD/DVR
FM/AM TAPE/VCR TV
TUNING
– + –
SYSTEM
SETUP VOLUME
FM wire antenna
+
ENTER
ROOM
SETUP
–
AUTO SURROUND
Batteries (x2)
OFF SOUND TONE
BASS TREBLE
– + –
AM loop
RECEIVER
antenna
Non-skid pads (1x12)
Remote control
You should also have:
• Speakers*
* Before placing the speakers,
• Subwoofer please refer to the speaker
• Operating instructions manual for detailed assembly
• Warranty card
instructions. Also check the
speaker manual for a complete
list of supplied accessories.
4
Connect antennas
Connect the FM wire antenna and fully extend along a
1
window frame or another suitable place that gives good
reception.
To connect the AM loop antenna, twist the exposed wire
2
strands together and insert into the terminal, then snap
the connector shut as shown below.
AM loop
antenna
FM wire antenna
ANTENNA
FM
UNBAL
75Ω
AM
LOOP
3/8 in.
(10mm)
For detailed instructions, see the Operating Instructions supplied and / or contact one of our knowledgeable Pioneer Customer Service Representatives at 1 - (800) 421-1404.
Put the batteries in the remote
2
control and stick the non-skid pads
to the base of the speakers.
Open the battery compartment on
1
MUTE
the rear of the remote control.
DIMMER
TUNER
EDIT
CLASS
Insert the supplied batteries
2
STATION following the markings inside the
+
battery compartment to align
CH LEVEL
them correctly.
TEST
TONE
3 Replace the battery compartment
STEREO
cover.
MPX
+
4 Stick the self-adhesive non-skid
pads to the underside of each
speaker. Use four pads per
speaker. Make sure to use a stable
surface when doing this, and lay
the speakers flat on their side.
Surround speakers Center speaker
Connect the receiver to your DVD
5
player/ recorder.
Use a coaxial digital cord (not supplied) to connect the digital
1
output of your DVD player/ recorder to the DIGITAL INPUT
(COAXIAL) DVD/DVR jack.
Use a red/white stereo audio cord (not supplied) to connect the
2
AUDIO TV IN jack on the receiver to the audio output on your
TV.* This will allow you to listen to your TV through this
speaker system.
* Note that you must also connect the DVD player/ recorder's
video output to your TV's video input to watch a DVD video
(video cable is not supplied).
DIGITAL INPUT
(COAXIAL)
DVD/DVR
Receiver
AUDIO
TV IN
+ +
IN
OUT
– –
R L
DIGITAL VIDEO
OUT OUT
DVD player/ recorder
3 Connect each speaker to the receiver using the
supplied speaker wires.
To connect, insert the colored wire into the matching colored
(+) tab and the other wire into the black (–) tab as shown below.
Note that the color-coded tabs are as follows:
• Red : Front right speaker
• White : Front left speaker
• Green : Center speaker
SPEAKERS
FRONT SUB
R L CENTER
WOOFER
+
–
For the best surround sound, set up your
speakers like this. The front left and right
speakers should be about 6–9 feet apart.
Plug the receiver, DVD player/
6
recorder and TV into a convenient
AC outlet.
1
Press STANDBY/ON to switch on the receiver.
STANDBY/ON
STANDBY/ON
Switch on your DVD player/ recorder and TV, and set the TV to
2
the correct video input.
Receiver
STANDBY/ON
R L
VIDEO AUDIO
TV
IN OUT
STANDBY/ON
DVD player/ recorder
Surround right
• Purple : Subwoofer
• Grey : Surround right speaker
• Blue : Surround left speaker
Receiver
SURROUND
R L
+
–
Front right
After switching on, make any
7
necessary settings required by the
DVD player/ recorder, then you're
ready to start enjoying your home
theater system.
Refer to the receiver's operating instructions for a detailed
explanation of this system's surround sound features.
VOLUME
+
–
Receiver
VIDEO 1
VIDEO SELECT
TV
Surround left
Listening position
Subwoofer
Front left
Center
INPUT SELECTOR
AUTO SURROUND STEREO
DIGITAL STB DVD/DVR
FM/AM TAPE/VCR TV