Siemens SIMATIC IPC3000 SMART Quick Install Manual

安装设备
Mounting the device
安装调试须知 - Before mounting and commissioning
重要信息: 在安装和连接设备前，应先仔细阅读设备附带的所有文档和产品操作手册。您可以在西门子
客户网站上找到产品的操作手册 （http://www.siemens.com/simatic-ipc-doku-portal）。
Important: observe all documents enclosed with the device and the operating instructions manual
before mounting and connecting the device. You can find the complete documentation of the device
on the internet (http://www.siemens.com/simatic-ipc-doku-portal).
此文件标识表示，如需详细信息请参阅操作手册。
The manual symbol refers to detailed information in the operating instructions.
! 小心
在操作带有安全警告标志的步骤时，应采取正确的保护措施，否则会造成轻度人身伤害。
! CAUTION
With a safety alert symbol, indicates that minor injury can result if proper precauions are not taken.
允许的使用位置 - Valid positions
45 °C
设备四周至少要预留 50 mm 的自由空间。
At least 50 mm space has to be left free arount the device.
安装设备 - Installing the device
小心
!
由于设备自身重量，只用前面板上的19英寸支架安装该设备是不安全的。
该设备可能摔落，造成人身伤害并损害设备。
为保证设备安全，应采用额外的安全措施。伸缩导轨的安装螺钉伸向设备的长度不得超过 5 mm。
CAUTION
!
The device is too heavy to be mounted exclusively with the 19 inch brackets of the front panel.
The device may fall down, injure people and get damaged.
Secure the device using addtional measures. The mounting screws of the telescopic rails may not
protrude more than 5 mm into the device.
角形托座安装
Mounting on angle brackets
1
1
2
导轨安装
Mounting on telescopic rails 3
1
2
(SSD) 40 °C (HDD)
5 °C 5 °C
基座安装
Mounting on device bases
1
1
2
1
1
连接设备
Connecting the device
接地连接 - Connecting the function earth
2
1
M4
1
I
0
连接电源– Connecting the power supply
小心
!
本设备仅适用于接地的电源系统系统（即符合IEC 60364-3规定的TN系统）。该产品不得用于非接地或
是阻抗接地的电源网络（IT网络）。
把本设备接入非接地或是阻抗接地的电源网络（IT网络）可能会造成人员触电、火灾、爆炸等事故。
为保证设备安全，应确保本设备接入的电源网络已正确接地。
CAUTION
!
The device is intended for operation on grounded power supply systems (TN systems according to IEC
60364-3). It is not designed for opertion on undergrounded or impedance-grounded power networks
(IT networks).
In case of connect the device to ungrounded or impedance-grounded power networks (IT networks),
there is a risk of electric shock, fire and burst.
Ensure the power supply system the device operating on is correctly grounded.
I
0
调试设备
Commissioning the device
接通设备 - Switching on the device
1
I
0
I
2
2
PH2
2.5mm²
I
O
1
1 设置开关位置到 " "。
Set the on/off switch to p
2 按开关键启动电脑。
Press the power on/off button to
start the computer.
1
I
0
2
osition " ".