Huawei SmartLogger3000 Quick Manual
Hide thumbs
Also See for SmartLogger3000:
- User manual (305 pages) ,
- Configuration manual (27 pages) ,
- Commissioning manual (40 pages)
Related Manuals for Huawei SmartLogger3000
Summary of Contents for Huawei SmartLogger3000
- Page 1 SmartLogger3000 Quick Guide Issue: 12 Part Number: 31500BWF Date: 2023-10-11 HUAWEI TECHNOLOGIES CO., LTD.
- Page 2 Log in to the technical support website (https://support.huawei.com/enterprise) to view the user manual and safety precautions. The information in this document is subject to change without notice. Every effort has •...
- Page 3 Overview (1) LED indicators (RUN, ALM, 4G) (2) SIM card slot (SIM) (3) Mounting ear (4) Guide rail clamp (5) MBUS port (MBUS) (6) GE port (WAN) (7) SFP ports (SFP1, SFP2) (8) 4G antenna port (4G) (9) RST button (RST) (10) USB port (USB) (11) GE port (LAN) (12) DI ports (DI)
-
Page 4: Installation Requirements
Installation Requirements Dimensions Space Device Installation Installing the SmartLogger Wall-Mounted Installation • Install the SmartLogger on a flat and secure interior wall. • When wall-mounting the SmartLogger, ensure that the cable connection area faces downwards for ease of cable connection and maintenance. •... -
Page 5: Installing The Power Adapter
Guide Rail-Mounted Installation • Before installing the SmartLogger, prepare a standard 35 mm guide rail and secure it. • The recommended effective length of the guide rail is 230 mm or greater. Installing the Power Adapter Wall-Mounted Installation It is recommended that the power adapter be installed on the right side of the SmartLogger. -
Page 6: Electrical Connections
Flat Surface-Mounted Installation Ensure that the power adapter indicator faces upward or outward. Electrical Connections • Connect cables in accordance with the installation laws and regulations of the country or region where the project is located. • Before connecting cables to ports, leave enough slack to reduce the tension on the cables and prevent poor cable connections. -
Page 7: Connecting The Rs485 Communications Cable
Connecting the PE Cable To enhance the corrosion resistance of the ground terminal, apply silica gel or paint on it after connecting the PE cable. Connecting the RS485 Communications Cable • It is recommended that the RS485 communication distance be less than or equal to 1000 m. •... - Page 8 Cascading Connection • You are advised to connect fewer than 30 devices to each RS485 route. • The baud rate, communications protocol, and parity mode of all devices on the RS485 cascading link must be the same as those of the COM ports on the SmartLogger. Connecting the MBUS Cable •...
- Page 9 MBUS Networking Connecting the DI Signal Cable • The SmartLogger can receive DI signals such as remote power grid scheduling commands and alarms over DI ports. It can only receive passive dry contact signals. • It is recommended that the signal transmission distance be less than or equal to 10 m. Port Description Can receive passive...
-
Page 10: Connecting The Output Power Cable
Connecting the Output Power Cable • In the export limitation or audible and visual alarm scenario, the SmartLogger can drive the coil of the intermediate relay through the 12 V output power port. • It is recommended that the transmission distance be less than or equal to 10 m. Intermediate relay Connecting the AI Signal Cable •... -
Page 11: Connecting The Ethernet Cable
Connecting the DO Signal Cable • The DO port supports a maximum of 12 V signal voltage. The NC/COM is a normally closed contact, while the NO/COM is a normally open contact. • It is recommended that the transmission distance be less than or equal to 10 m. Connecting the Ethernet cable •... - Page 12 4.10 Connecting the Optical Jumper • The SmartLogger can connect to devices such as the access terminal box through optical fibers. • Optical modules are optional. Configure the 100M or 1000M optical module based on the peer port on the optical switch. The optical module should use the SFP or eSFP encapsulation. The transmission distance supported by the 100M optical module should be greater than or equal to 12 km, and the transmission distance supported by the 1000M optical module should be greater than or equal to 10 km.
- Page 13 Monthly Traffic Requirement of the SIM Card Traffic Baseline Without a power • Device meter or energy 10 MB + 4 MB x Number of solar inverters performance data storage can be refreshed With a power every 5 minutes. Solar 10 MB + 7 MB x Number of solar inverters •...
-
Page 14: Check Before Power-On
Check Before Power-On Criterion The SmartLogger is installed correctly and securely. All cables are securely connected. Routing of power cables and signal cables meets the requirements for routing electric and ELV cables and complies with the cable routing plan. Cables are bound neatly, and cable ties are secured evenly and properly in the same direction. - Page 15 Indicator Status Meaning Green off The SmartLogger is not powered on The communication between the Blinking green slowly (on for 1s and then SmartLogger and the management Running indicator off for 1s) system is normal. (RUN) The communication between the Blinking green fast (on for 0.125s and SmartLogger and the management then off for 0.125s)
- Page 16 • When the IP address of the WAN port is in the network segment from 192.168.8.1 to 192.168.8.255, set the default gateway to 192.168.8.1 and the IP address of the LAN port to 192.168.3.10. If the connected port is a LAN port, you need to adjust the network configuration of the PC.
- Page 17 Connecting the SmartLogger to the FusionSolar Smart PV Management System 1. Enable the public network of the mobile phone, open the FusionSolar app, log in to intl.fusionsolar.huawei.com as installer account, and choose Me > Device commissioning to connect to the WLAN hotspot of the SmartLogger.
- Page 18 • The screenshots in this document correspond to the FusionSolar app version 6.22.10.118 (Android) and SUN2000 app version 6.22.10.117 (Android). • The initial WLAN hotspot name of the SmartLogger is Logger_ and the initial password is Changeme. The SN can be obtained from the SmartLogger label. •...
-
Page 19: Rst Button
The 4G Communication Is Abnormal 1. Check whether the SIM card is properly installed. 2. Check whether the SIM card is damaged or the charge is overdue. 3. Check whether the 4G antenna is tightened or damaged. 4. Check whether the management system parameters and wireless network parameters are set correctly. - Page 20 Huawei Technologies Co., Ltd. Huawei Industrial Base, Bantian, Longgang Shenzhen 518129 People's Republic of China e.huawei.com...