Changing The Transmitting Frequency; Changing The Output Level; Playing Tracks In Random Order; Playing Tracks Repeatedly - Sony CDX-505RF Operating Instructions Manual

Listening to a CD
1 Turn on the FM tuner of the car audio.
2 Adjust the selected transmitting frequency
with the wired remote.
(88.3 MHz/88.5 MHz/88.7 MHz/88.9 MHz/
89.1MHz/ 89.3 MHz/89.5 MHz/89.7 MHz/
89.9 MHz)
3 Press the PHl.
CD playback start.
4 Adjust the volume with the volume control
on the car audio.
All the tracks play from the begining.
Stopping CD play
Press (OFF).
Notes
© When CD playback is stopped, you may hear some noise
from the speakers. To prevent this from happening, turn the
volume down before stopping CD playback.
* If you turn off the ignition switch of your car without
stopping CD playback, it will automatically resume CD
playback from where it was stopped the next time you turn
on the ignition switch.
Listening to the radio or a tape
Be sure to stop CD playback before you start
listening to the radio or a tape.
Note
Be sure to stop CD playback, otherwise there may be some
interference with radio reception.
Playing tracks in random order
— Shuffle Play
You can select:
¢SHUF 1 to play the tracks ort the current disc in
a random order.
¢ SHUF 2 to play all the discs in a random order.
Press repeatedly until the desired
setting appears (SHUF1 or SHUF2).
After five seconds, the shuffle play starts.
'Each time you press (SHUF), the display
changes as follows:
—— 1. ———» SHUF 2
Cancel (SHUF off) ie aed
To go back to the normal playback mode,
press until the "SHUF" disappears.
Playing tracks repeatedly
— Repeat Play
You can select:
¢ REP 1 to repeat the track.
¢ REP 2 to repeat the disc.
Press repeatedly until the desired
setting appears (REP1 or REP2).
After five seconds, the repeat play starts.
Each time vou press CREP), the display
changes as follows:
> REP 1—® REP 2 —> Cancel (REP off) 7]
To go back to the normal playback mode,
press CREP) until "REP" disappears.
Changing the transmitting
frequency
Because this unit processes CD playback sound
through an FM tuner, there may be interference
noise during CD playback. In this case change the
frequency of the modulated RF signal transmitted
from hideaway unit. The initial setting is 88.3
MHz.
1 Press for more than two seconds.
2 Press either the left or right side of
to select the frequency.
Each time you press (AMS), the frequencys
change as follows:
Pi - 88.3 MHz — 88.5 MHz — 88.7 MHz >
88.9 MHz — 89.1 MHz — 89.3 MHz
89.5 MHz — 89.7 MHz — 89.9 MHz
Kd: 89.9 MHz — 89.7 MHz — 89.5 MHz —>
89.3 MHz — 89.1 MHz — 88.9 MHz —>
88.7 MHz — 88.5 MHz — 88.3 MHz
3 Press for more than two seconds.
Note
Be sure to set the frequency of your FM tuner to the newly
selected frequency.
ees
Changing the output level
You can select the output level from the CD
changer. Normally the system is used at the
initial output level; change the level if necessary.
1 Press for more than two seconds.
2 Press CREP).
re no
mg 3UU wu Initial setting
3 Press either the left or right side of
to select the output level.
To decrease the output level
wai a> |> ff
co !
CEvEL
To increase the output level
re amr
>: = co 4LILS Lu
4 Press for more than two seconds.