Husqvarna HG 125 B Original Instructions Manual page 19

justments, changing accessories, or
storing power tools. Such preventive
safety measures reduce the risk of starting the
power tool accidentally.
Store idle power tools out of the reach
u
of children and do not allow persons
unfamiliar with the power tool or these
instructions to operate the power
tool. Power tools are dangerous in the hands
of untrained users.
Maintain power tools. Check for mis-
u
alignment or binding of moving parts,
breakage of parts and any other condi-
tion that may affect the power tool's
operation. If damaged, have the power
tool repaired before use. Many accidents
are caused by poorly maintained power tools.
Keep cutting tools sharp and clean.
u
Properly maintained cutting tools with sharp cut-
ting edges are less likely to bind and are easier
to control.
Use the power tool, accessories and
u
tool bits etc. in accordance with these
instructions, taking into account the
working conditions and the work to be
performed. Use of the power tool for opera-
tions different from those intended could result
in a hazardous situation.
Battery tool use and care
Recharge only with the charger spe-
u
cified by the manufacturer. A charger
that is suitable for one type of battery pack may
create a risk of fire when used with another bat-
tery pack.
Use power tools only with specifically
u
designated battery packs. Use of any
other battery packs may create a risk of injury
and fire.
When battery pack is not in use, keep
u
it away from other metal objects, like
paper clips, coins, keys, nails, screws
or other small metal objects, that can
make a connection from one terminal
to another. Shorting the battery terminals to-
gether may cause burns or a fire.
Under abusive conditions, liquid may
u
be ejected from the battery; avoid con-
tact. If contact accidentally occurs,
flush with water. If liquid contacts
eyes, additionally seek medical help.
Liquid ejected from the battery may cause irrita-
tion or burns.
Service
English
Have your power tool serviced by a
u
qualified repair person using only
identical replacement parts. This will en-
sure that the safety of the power tool is main-
tained.
1 609 92A 6WV • 26.8.22
Safety Warnings for Angle
Grinder
Safety Warnings common for
Grinding, Sanding, Wire Brushing or
Abrasive Cutting Off operations
This power tool is intended to function
u
as a grinder, sander, wire brush or cut-
off tool. Read all safety warnings, in-
structions, illustrations and specifica-
tions provided with this power tool.
Failure to follow all instructions listed below may
result in electric shock, fire and/or serious injury.
Operations such as polishing are not
u
recommended to be performed with
this power tool. Operations for which the
power tool was not designed may create a haz-
ard and cause personal injury.
Do not use accessories which are not
u
specifically designed and recommen-
ded by the tool manufacturer. Just be-
cause the accessory can be attached to your
power tool, it does not assure safe operation.
The rated speed of the accessory must
u
be at least equal to the maximum
speed marked on the power tool. Ac-
cessories running faster than their rated speed
can break and fly apart.
English
The outside diameter and the thick-
u
ness of your accessory must be within
the capacity rating of your power tool.
Incorrectly sized accessories cannot be ad-
equately guarded or controlled.
Threaded mounting of accessories
u
must match the grinder spindle thread.
For accessories mounted by flanges,
the arbour hole of the accessory must
fit the locating diameter of the flange.
Accessories that do not match the mounting
hardware of the power tool will run out of bal-
ance, vibrate excessively and may cause loss of
control.
Do not use a damaged accessory. Be-
u
fore each use inspect the accessory
such as abrasive wheels for chips and
cracks, backing pad for cracks, tear or
excess wear, wire brush for loose or
cracked wires. If power tool or access-
ory is dropped, inspect for damage or
install an undamaged accessory. After
inspecting and installing an accessory,
position yourself and bystanders away
from the plane of the rotating access-
ory and run the power tool at max-
imum no load speed for one minute.
Damaged accessories will normally break apart
during this test time.
English
English
English | 19