Table of Contents

Advertisement

Quick Links

HCD-G2BNiP/G2NiP
SERVICE MANUAL
Ver. 1.1 2012.03
• HCD-G2BNiP is compact disc receiver in CMT-G2BNiP.
• HCD-G2NiP is compact disc receiver in CMT-G2NiP.
Note:
Be sure to keep your PC used for service and
checking of this unit always updated with the
latest version of your anti-virus software.
In case a virus affected unit was found during
service, contact your Service Headquarters.
Amplifier section
Tuner section
European models:
AM tuner section:
Power output (rated):
Tuning range:
40 watts + 40 watts (6 ohms at 1 kHz, 1% THD)
European model:
Continuous RMS power output (reference):
531 kHz – 1,602 kHz (with 9 kHz tuning interval)
50 watts + 50 watts (6 ohms at 1 kHz, 10% THD)
Other models:
530 kHz – 1,710 kHz (with 10 kHz tuning interval)
Music power output (reference):
531 kHz – 1,710 kHz (with 9 kHz tuning interval)
60 watts + 60 watts (6 ohms at 1 kHz, 10% THD)
Antenna:
Australian model:
AM loop antenna
Power output (rated):
Intermediate frequency:
40 watts + 40 watts (6 ohms at 1 kHz, 1% THD)
400 kHz
Continuous RMS power output (reference):
FM tuner section:
50 watts + 50 watts (6 ohms at 1 kHz, 10% THD)
FM stereo, FM superheterodyne tuner
Tuning range:
Wireless LAN section
87.5 MHz – 108.0 MHz (50 kHz step)
Compatible standards:
Antenna:
IEEE 802.11 b/g (WEP 64 bit, WEP 128 bit,
FM lead antenna
WPA/WPA2-PSK (AES), WPA/WPA2-PSK
(TKIP))
Antenna terminals:
75 ohms unbalanced
Radio frequency:
2.4 GHz
Intermediate frequency:
200 kHz, 250 kHz, 300 kHz, 350 kHz, 400 kHz
CD player section
DAB/DAB+ tuner section
System:
(HCD-G2BNiP only):
Compact disc and digital audio system
FM stereo, DAB/FM superheterodyne tuner
Laser Diode Properties
Frequency range
Emission Duration: Continuous
Band-III:
Laser Output*: Less than 44.6μW
174.928 (5A) MHz – 239.200 (13F) MHz
* This output is the value measurement at a distance of
200mm from the objective lens surface on the Optical
Antenna:
Pick-up Block with 7mm aperture.
DAB/FM lead antenna
Frequency response:
20 Hz – 20 kHz
Signal-to-noise ratio:
More than 90 dB
Dynamic range:
More than 90 dB
9-893-336-02
Sony Corporation
2012C33-1
©
2012.03
Published by Sony Techno Create Corporation
Photo: HCD-G2BNiP
Model Name Using Similar Mechanism
CD Mechanism Type
Base Unit Name
Optical Pick-up Block Name
SPECIFICATIONS
DAB/DAB+ frequency table (Band-III)
iPod/iPhone section
Frequency
Label
Compatible iPod/iPhone models:
174.928 MHz
5A
176.640 MHz
5B
178.352 MHz
5C
180.064 MHz
5D
181.936 MHz
6A
183.648 MHz
6B
185.360 MHz
6C
iPod touch
187.072 MHz
6D
4th generation
188.928 MHz
7A
190.640 MHz
7B
192.352 MHz
7C
194.064 MHz
7D
195.936 MHz
8A
197.648 MHz
8B
199.360 MHz
8C
iPod touch
1st generation
201.072 MHz
8D
202.928 MHz
9A
204.640 MHz
9B
206.352 MHz
9C
208.064 MHz
9D
209.936 MHz
10A
211.648 MHz
10B
iPod nano
213.360 MHz
10C
4th generation
215.072 MHz
10D
(video)
216.928 MHz
11A
218.640 MHz
11B
220.352 MHz
11C
222.064 MHz
11D
223.936 MHz
12A
225.648 MHz
12B
227.360 MHz
12C
iPod classic
229.072 MHz
12D
230.784 MHz
13A
232.496 MHz
13B
234.208 MHz
13C
235.776 MHz
13D
237.488 MHz
13E
239.200 MHz
13F
iPhone 3G
COMPACT DISC RECEIVER
AEP Model
HCD-G2BNiP/G2NiP
UK Model
Australian Model
HCD-G2BNiP
NEW
CDM77B-K6BD94DC
BU-K6BD94DC
KSM-213DCP
USB section
Supported bit rate:
MP3 (MPEG 1 Audio Layer-3): 32 kbps –
320 kbps, VBR
WMA: 48 kbps – 192 kbps, VBR
AAC: 48 kbps – 320 kbps
Sampling frequencies:
MP3 (MPEG 1 Audio Layer-3): 32/44.1/48 kHz
WMA: 44.1 kHz
AAC: 44.1 kHz
iPod touch
iPod touch
3rd generation
2nd generation
Inputs/Outputs
FM Antenna terminals:
75 ohms unbalanced
DAB/DAB+ Antenna terminal:
75 ohms, F female
AUDIO IN (RCA):
Sensitivity 700 mV, impedance 47 kilohms
iPod nano
iPod nano
6th generation
5th generation
SPEAKERS:
(video camera)
Accepts impedance of 6 ohms – 16 ohms
(USB) port:
Type A, maximum current 1 A
NETWORK
port:
10BASE-T/100BASE-TX
iPod nano
General
iPod nano
3rd generation
2nd generation
(video)
(aluminum)
Power requirements:
European models:
AC 220 V – 230 V, 50/60Hz
Australian model:
AC 230 V – 240 V, 50/60 Hz
Power consumption:
50 watts
iPhone 4
iPhone 3GS
Dimensions (W/H/D) (excl. speakers):
Approx. 220 mm × 141 mm × 335 mm
Mass (excl. speakers):
Approx. 5.6 kg
Design and specifications are subject to change
without notice.
Standby power consumption: 0.5 W
iPhone

Advertisement

Table of Contents
loading

Summary of Contents for Sony HCD-G2BNiP

  • Page 1 HCD-G2BNiP/G2NiP UK Model Ver. 1.1 2012.03 Australian Model HCD-G2BNiP • HCD-G2BNiP is compact disc receiver in CMT-G2BNiP. Photo: HCD-G2BNiP • HCD-G2NiP is compact disc receiver in CMT-G2NiP. Note: Model Name Using Similar Mechanism Be sure to keep your PC used for service and...
  • Page 2: Table Of Contents

    WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS Professional, Microsoft Windows 7 Ultimate are marking is located on the rear referred to as Windows 7. MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. exterior. ™ and ® marks are omitted in this manual.
  • Page 3: Servicing Notes

    Part No. pickup block. Therefore, when checking the laser diode emission, HCD-G2NiP: AEP model 4-275-277-0[] observe from more than 30 cm away from the objective lens. HCD-G2BNiP: AEP and UK models 4-275-277-1[] UNLEADED SOLDER HCD-G2BNiP: Australian model 4-275-277-2[] Boards requiring use of unleaded solder are printed with the lead- free mark (LF) indicating the solder contains no lead.
  • Page 4 HCD-G2BNiP/G2NiP NOTE OF REPLACING THE WIRELESS LAN MODULE (MOD1) When replacing the wireless LAN module (MOD1), MAC address is changed. Print the following explanation, cut it, and hand over it to the customer with the unit, when returning the unit that the repair is completed to the customer.
  • Page 5 HCD-G2BNiP/G2NiP HOW TO OPEN THE TRAY WHEN POWER SWITCH TURN OFF lever 1 Insert the hard metal fittings of L character type 6 cm or more in the hole of the chassis. 6 cm or more hole 2 Push the lever in the direction of the arrow A.
  • Page 6 HCD-G2BNiP/G2NiP FL-NET, JOG1, JOG2, USB AND HP BOARD SERVICE POSITION JOG1 board HP board JOG2 board USB board FL-NET board insulating sheet CD MECHANISM DECK SERVICE POSITION MAIN board BD94DC board CD mechanism deck (CDM77B-K6BD94DC) front panel block MOTOR board...
  • Page 7 HCD-G2BNiP/G2NiP SUB-PT BOARD SERVICE POSITION SUB-PT board MAIN board AMP BOARD SERVICE POSITION AMP board Note: Connect the alligator clips surely with this position. MAIN board CN103 alligator clips lug wire Connect extension jig (Part No. J-2501-212-A) to the AMP board (CN103) and MOTOR board.
  • Page 8 HCD-G2BNiP/G2NiP DCDC BOARD SERVICE POSITION DCDC board MAIN board TUNER AND DAB BOARD SERVICE POSITION Note: Both the flexible flat cable (9 core) can be connected with the CN406 or CN407 on MAIN board. When you connect the flexible flat cable (9 core) with...
  • Page 9 HCD-G2BNiP/G2NiP WIRE SETTING coating clip holder NET board (BREDGECO) coating clip tape coating clip tape MAIN board wireless LAN module (MOD1) front side MAIN board NET board AMP board MAIN board Note 1: flexible flat cable must not touch a screw.
  • Page 10: Disassembly

    HCD-G2BNiP/G2NiP SECTION 2 DISASSEMBLY • This set can be disassembled in the order shown below. 2-1. DISASSEMBLY FLOW 2-2. CASE BLOCK 2-4. PANEL (CD TRAY) (Page 11) (Page 12) 2-6. PANEL (REAR) BLOCK 2-3. WIRELESS LAN 2-7. MAIN BOARD 2-5. PANEL (FRONT) BLOCK...
  • Page 11: Case Block

    HCD-G2BNiP/G2NiP Note: Follow the disassembly procedure in the numerical order given. 2-2. CASE BLOCK 6 case block 1 four screws (BV/ring) 2 flat head screw (TP) 5 two claws 2 flat head screw (TP) 2-3. WIRELESS LAN MODULE (MOD1) 1 two screws 2 coating clip Note 1: Refer to “WIRE SETTING”...
  • Page 12: Panel (Cd Tray)

    HCD-G2BNiP/G2NiP 2-4. PANEL (CD TRAY) 5 panel (CD tray) Note: There is a possibility of damaged of the panel (CD tray) when the panel (front) block is removed without removing the panel (CD tray). Remove panel (CD tray) earlier than removing the panel (front) block.
  • Page 13: Panel (Front) Block

    HCD-G2BNiP/G2NiP 2-5. PANEL (FRONT) BLOCK 8 screw (BVTP3 9 two screws 6 flexible flat cable (19 core) (BV/ring) (CN404) 4 Lift up the coating clip. 5 Turn over the flexible flat cable (15 core). qa panel (front) block 0 claw...
  • Page 14: Panel (Rear) Block

    HCD-G2BNiP/G2NiP 2-6. PANEL (REAR) BLOCK Note 1: Refer to “WIRE SETTING” on page 9 for wire setting. 1 two screws (BVTP2.6) 2 coating clip 3 holder (BREDGECO) (G2BNiP) Note 2: When you install the flexible flat cable, please install them qa flexible flat cable (8 core) (CN408) correctly.
  • Page 15: Main Board

    HCD-G2BNiP/G2NiP 2-7. MAIN BOARD Note 1: Refer to “WIRE SETTING” on page 9 for wire setting. (G2BNiP) qs flexible flat cable (8 core) (CN408) 2 connector qa flexible flat cable (9 core) (CN407) (CN701) Note 4: Both the flexible flat cable (9 core) can be connected with the CN406 or CN407 on MAIN board.
  • Page 16: Net Board

    HCD-G2BNiP/G2NiP 2-8. NET BOARD 3 NET board 2 two screws 2 two screws (BVTP3 (BVTP3 1 flexible flat cable (21 core) (CN5005) Note: When you install the flexible flat cable, please install them correctly. There is a possibility that this machine damages when not correctly installing it.
  • Page 17: Amp Board Block

    HCD-G2BNiP/G2NiP 2-10. AMP BOARD BLOCK 4 two screw (BV3) 4 screw (BV3) 2 Lift up the lead pin. 6 AMP board block 1 flexible flat cable (5 core) (CN103) 3 connector (CN301) 5 lug wire – – Note: When you install the flexible flat cable, please install them AMP board correctly.
  • Page 18: Amp Board

    HCD-G2BNiP/G2NiP 2-11. AMP BOARD Note 1: When you install the flexible flat cable, please install them correctly. There is a possibility that this machine damages flexible flat cable (15 core) when not correctly installing it. 35 mm Insert is straight to the interior...
  • Page 19: Power Transformer (T901)

    HCD-G2BNiP/G2NiP 2-12. POWER TRANSFORMER (T901) 9 clamp filter (ferrite core) 0 power transformer (T901) 2 connector 3 Remove the coating clip from (CN301) front side the clamp filter (ferrite core). 9 clamp filter (ferrite core) 5 connector (CN952) 8 plate (trans) 1 Lift up the lead pin.
  • Page 20: Cd Mechanism Deck Block (Cdm77B-K6Bd94Dc)

    HCD-G2BNiP/G2NiP 2-13. CD MECHANISM DECK BLOCK (CDM77B-K6BD94DC) Note: When you install the flexible flat cable, please install them 1 cover (CD top) correctly. There is a possibility that this machine damages when not correctly installing it. Insert is straight to the interior...
  • Page 21: Base Unit (Bu-K6Bd94Dc)

    HCD-G2BNiP/G2NiP 2-15. BASE UNIT (BU-K6BD94DC) 1 floating screw 1 two floating screws (PTPWHM2.6) (PTPWHM2.6) 4 insulator 1 two floating screws (PTPWHM2.6) 2 two cone springs Note: When you install the cone spring, adjust sharp side to 2 two cone springs the floating screw side.
  • Page 22: Holder (Cd) Block

    HCD-G2BNiP/G2NiP 2-17. HOLDER (CD) BLOCK 5 holder (CD) block Note: Confirm the wire does not rear side hit the edge of holder (CD). lead pin clamp filter 3 Remove the coating clip from (ferrite core) the clamp filter (ferrite core).
  • Page 23: Test Mode

    HCD-G2BNiP/G2NiP SECTION 3 TEST MODE COLD RESET PANEL TEST MODE The cold reset clears all data including preset data stored in the This mode is used to check the fl uorescent indicator tube, LED, memory to initial conditions. Execute this mode when returning model, destination, software version and key.
  • Page 24: Electrical Check

    HCD-G2BNiP/G2NiP SECTION 4 ELECTRICAL CHECK DISC TRAY LOCK MODE FM TUNE LEVEL CHECK This mode is used to unable to take sample disc out of disc tray in the shop. signal generator Procedure: unit 1. Press the [ ] button to turn the power on.
  • Page 25: Diagrams

    HCD-G2BNiP/G2NiP SECTION 5 DIAGRAMS 5-1. BLOCK DIAGRAM - CD/USB/PANEL Section - CD-MP3 PROCESSOR IC101 AOUT1 CD_DATA BCKO CD_BCK (Page 26) LRCKO CD_LRCK CN4602 USB DRIVER IC601 SIGNAL PATH : CD PLAY 34 USB_DP DATA USB_DATA D– : USB USB_BCK (Page 26)
  • Page 26: Block Diagram - Tuner/Network Section

    HCD-G2BNiP/G2NiP 5-2. BLOCK DIAGRAM - TUNER/NETWORK Section - D/A CONVERTER IC805 IC802 CD_DATA DATAI3 DATAMO DATA1 VOUT1 AUDIO-L (Page 25) CD_BCK BCKI3 11 DATA2 VOUT3 CD_LRCK LRCKI3 BCKO (G2NiP) (Page LRCKO LRCK VOUT2 AUDIO-R AMCLKO USB_DATA DATAI4 VOUT4 (Page 25)
  • Page 27: Block Diagram - Amp Section

    HCD-G2BNiP/G2NiP 5-3. BLOCK DIAGRAM - AMP Section - R-ch is omitted due to same as L-ch. SIGNAL PATH : TUNER ELECTRICAL VOLUME IC101 AUDIO-L IN-R OUT-R LINE LINE Q1101 – IC2222 IC103 AUDIO-R 9 IN-L OUT-L (Page TB301 R-CH Q1102...
  • Page 28: Block Diagram - Power Supply Section

    HCD-G2BNiP/G2NiP 5-4. BLOCK DIAGRAM - POWER SUPPLY Section - T901 MAIN POWER TRANSFORMER F303 +18V RECT D301 –18V F304 D306 D305 D304 +12V IC107_VAA REGULATOR REGULATOR IC112 IC108 A +5V REGULATOR IC807 REGULATOR IC107_VCC Q108 A +7V REGULATOR IC111 +1.2V LAN +1.2V...
  • Page 29 HCD-G2BNiP/G2NiP THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. • Circuit Boards Location. (In addition to this, the necessary note is printed in each block.) For Printed Wiring Boards. For Schematic Diagrams. TUNER board LAN board module (DAB tuner) (DAB1)
  • Page 30: Printed Wiring Board - Bd94Dc Board

    HCD-G2BNiP/G2NiP 5-5. PRINTED WIRING BOARD - BD94DC Board - • See page 29 for Circuit Boards Location. • : Uses unleaded solder. BD94DC BOARD (CONDUCTOR SIDE) BD94DC BOARD (COMPONENT SIDE) CL209 CL210 C405 CL309 C401 R405 R411 CL228 R416 C403...
  • Page 31: Schematic Diagram - Bd94Dc Board

    HCD-G2BNiP/G2NiP 5-6. SCHEMATIC DIAGRAM - BD94DC Board - • See page 50 for Waveforms. • See page 51 for IC Block Diagrams. • See page 56 for IC Pin Function Description. BD94DC BOARD C132 R137 R147 C160 C136 C303 C302...
  • Page 32: Printed Wiring Board - Tuner Board

    HCD-G2BNiP/G2NiP Ver. 1.1 5-7. PRINTED WIRING BOARD - TUNER Board - 5-8. SCHEMATIC DIAGRAM - TUNER Board - • See page 50 for Waveforms. • See page 51 for IC Block Diagrams. • See page 29 for Circuit Boards Location.
  • Page 33: Printed Wiring Board - Dab Board (G2Bnip)

    HCD-G2BNiP/G2NiP 5-9. PRINTED WIRING BOARD - DAB Board (G2BNiP) - 5-10. SCHEMATIC DIAGRAM - DAB Board (G2BNiP) - • See page 51 for IC Block Diagrams. • See page 29 for Circuit Boards Location. • : Uses unleaded solder. DAB BOARD...
  • Page 34: Printed Wiring Boards - Network Section

    HCD-G2BNiP/G2NiP 5-11. PRINTED WIRING BOARDS - NETWORK Section - • See page 29 for Circuit Boards Location. • : Uses unleaded solder. NET BOARD NET BOARD (SIDE A) (SIDE B) ET5001 ET5002 R5011 R5005 (CHASSIS) R5010 R5007 (CHASSIS) R5074 CL5012...
  • Page 35: Schematic Diagram - Network Section

    HCD-G2BNiP/G2NiP 5-12. SCHEMATIC DIAGRAM - NETWORK Section - • See page 50 for Waveforms. • See page 51 for IC Block Diagrams. NET BOARD JL5001 C5033 C5040 1000p D5002 R5075 ANT1 DA2J10100L IC B/D MOD1 L5001 R5085 C5031 WIRELESS 10uH...
  • Page 36: Printed Wiring Board - Main Board (Side A)

    HCD-G2BNiP/G2NiP Ver. 1.1 5-13. PRINTED WIRING BOARD - MAIN Board (Side A) - • See page 29 for Circuit Boards Location. • : Uses unleaded solder. (Page 33) (Page 48) (Page 32) (G2BNiP) DAB BOARD DCDC BOARD TUNER BOARD MAIN BOARD...
  • Page 37: Printed Wiring Board - Main Board (Side B)

    HCD-G2BNiP/G2NiP 5-14. PRINTED WIRING BOARD - MAIN Board (Side B) - • See page 29 for Circuit Boards Location. • : Uses unleaded solder. MAIN BOARD (SIDE B) C627 R606 R604 R608 Q802 Q801 R607 R609 R594 (G2BNiP) C602 R908...
  • Page 38: Schematic Diagram - Main Board (1/3)

    HCD-G2BNiP/G2NiP 5-15. SCHEMATIC DIAGRAM - MAIN Board (1/3) - • See page 50 for Waveforms. • See page 51 for IC Block Diagrams. • See page 56 for IC Pin Function Description. MAIN BOARD (1/3) JL829 Q807-809, 812 D802 R2437...
  • Page 39: Schematic Diagram - Main Board (2/3)

    HCD-G2BNiP/G2NiP Ver. 1.1 5-16. SCHEMATIC DIAGRAM - MAIN Board (2/3) - • See page 50 for Waveforms. • See page 51 for IC Block Diagrams. • See page 56 for IC Pin Function Description. (Page 40) (Page 49) (Page 47)
  • Page 40: Schematic Diagram - Main Board (3/3)

    HCD-G2BNiP/G2NiP Ver. 1.1 5-17. SCHEMATIC DIAGRAM - MAIN Board (3/3) - • See page 50 for Waveforms. • See page 51 for IC Block Diagrams. • See page 56 for IC Pin Function Description. MAIN BOARD (3/3) C622 R648 FB604...
  • Page 41: Schematic Diagram - Amp Section

    HCD-G2BNiP/G2NiP 5-18. SCHEMATIC DIAGRAM - AMP Section - • See page 51 for IC Block Diagrams. AMP BOARD IC B/D W001 IC102 (CHASSIS) Note 1: If checking operations LOADING MOTOR DRIVE IC102 C225 C228 C223 C226 C227 with the power on, be...
  • Page 42: Printed Wiring Board - Amp Section (1/2)

    HCD-G2BNiP/G2NiP 5-19. PRINTED WIRING BOARD - AMP Section (1/2) - • See page 29 for Circuit Boards Location. • : Uses unleaded solder. (Page 36) AMP BOARD MAIN BOARD (COMPONENT SIDE) CN403 (CHASSIS) (CHASSIS) R310 ET302 CN102 ET101 (CHASSIS) ET201...
  • Page 43: Printed Wiring Boards - Amp Section (2/2)

    HCD-G2BNiP/G2NiP 5-20. PRINTED WIRING BOARDS - AMP Section (2/2) - • See page 29 for Circuit Boards Location. • : Uses unleaded solder. (Page 36) MOTOR MAIN BOARD AMP BOARD BOARD CN803 (CONDUCTOR SIDE) C205 R111 FB104 JL107 R110 JL115...
  • Page 44: Printed Wiring Boards - Hp/Jog1/Jog2/Usb Boards

    HCD-G2BNiP/G2NiP Ver. 1.1 5-21. PRINTED WIRING BOARDS - HP/JOG1/JOG2/USB Boards - • See page 29 for Circuit Boards Location. • : Uses unleaded solder. JOG1 BOARD JOG2 BOARD JL4324 JL4323 JL4322 R4307 R4317 R4323 R4327 JL4321 R4321 R4328 NO4302 NO4321...
  • Page 45: Schematic Diagram - Hp/Jog1/Jog2/Usb Boards

    HCD-G2BNiP/G2NiP Ver. 1.1 5-22. SCHEMATIC DIAGRAM - HP/JOG1/JOG2/USB Boards - JOG1 BOARD CN4301 JL4301 JOG1 BASS JL4302 JOG2 TREBLE JL4303 JOG3 FUCTION JL4304 JOG4 VOLUME FL-NET JL4305 JOG2 BOARD R4317 BOARD SIRCS 4.7k JL4306 CN4102 3.3V (Page 47) S4302 S4301...
  • Page 46: Printed Wiring Board - Fl-Net Board

    HCD-G2BNiP/G2NiP 5-23. PRINTED WIRING BOARD - FL-NET Board - • See page 29 for Circuit Boards Location. • : Uses unleaded solder. (Page 44) JOG1 BOARD CN4301 CN4102 JL4117 S4104 JL4119 R4117 JL4118 JL4120 S4103 S4102 T4101 S4101 – 4111...
  • Page 47: Schematic Diagram - Fl-Net Board

    HCD-G2BNiP/G2NiP 5-24. SCHEMATIC DIAGRAM - FL-NET Board - • See page 50 for Waveforms. FL-NET BOARD T4101 R4102 L4101 DC/DC CONVERTER 100uH TRANSFORMER R4136 R4103 R4104 VDD-C R4135 2.7k D4101 MC2836-T112-1 VDD-D C4120 C4121 C4101 D4102 LGND-C C4103 MC2838-T112-1 JL4123 0.01...
  • Page 48: Printed Wiring Boards - Power Supply Section

    HCD-G2BNiP/G2NiP Ver. 1.1 5-25. PRINTED WIRING BOARDS - POWER SUPPLY Section - • See page 29 for Circuit Boards Location. • : Uses unleaded solder. DCDC BOARD (COMPONENT SIDE) (Page 43) R953 C959 AMP BOARD T901 CN301 C989 MAIN POWER...
  • Page 49: Schematic Diagram - Power Supply Section

    HCD-G2BNiP/G2NiP 5-26. SCHEMATIC DIAGRAM - POWER SUPPLY Section - • See page 51 for IC Block Diagrams. DCDC BOARD IC B/D IC951 DC/DC CONVERTER IC951 BD9329AEFJ-E2 F951 D951 T4AL JL951 JL952 10EDB40-TB3 250V D952 R951 CN952 10EDB40-TB3 C951 C953 R993...
  • Page 50 HCD-G2BNiP/G2NiP • Waveforms – BD94DC Board – – NET Board – – MAIN Board – – FL-NET Board – IC101 wf (XO) IC5002 2 (RCKI) IC805 wf (ERR1_LRC) IC805 ra (LRCKI) IC805 t; (LRCKI4) Q4101 (Base) (CD play mode) 3.7 Vp-p 3.9 Vp-p...
  • Page 51 HCD-G2BNiP/G2NiP • IC Block Diagrams – BD94DC Board – IC201 MM3404A15URE IC401 BA5826HFP-E2 VO1(–) D.BUFF VO4(–) CE 1 BIAS VO1(+) D.BUFF LEVEL D.BUFF VO4(+) SHIFT VOLTAGE – D.BUFF REFERENCE LEVEL SHIFT CURRENT RESET LIMIT VOUT IN4' THERMAL SHUT-DOWN GND 2...
  • Page 52 HCD-G2BNiP/G2NiP – DAB Board – – NET Board – IC4001 MM3291CNRE IC5001 SI-3010KM-TLS REGULATOR VDD 1 VOUT GND 2 CE 3 – VOUT IC5002 SRC4182 LGRP REFERENCE INTERPOLATION DECIMATION RCKI RE-SAMPLER CLOCK FILTERS FILTERS 28 MODE2 SDIN 27 MODE1 AUDIO...
  • Page 53 HCD-G2BNiP/G2NiP – MAIN Board – IC403 PST8429UL GND 1 VREF – VDD 2 IC602 TPS2553DBVR IC704 BD00GA3WEFJ-E2 IC705 BD00GC0WEFJ-SE2 RREVERSE VOLTAGE – COMPARATOR CURRENT IN 1 6 OUT SENSE 4-ms DEGLITCH CHARGE SOFT GND 2 PUMP CURRENT EN 3 DRIVER...
  • Page 54 HCD-G2BNiP/G2NiP IC802 PCM1681PWPR ZR1/ZR1/FMT0 1 SYSTEM CLOCK SYSTEM ZERO MANAGER CLOCK DETECT POWER SUPPLY VOUT1 OUTPUT AMP AND MS/ADR/FMT1 2 CONVERTER LOW-PASS FILTER FUNCTION MC/SCL/DEMP 3 CONTROL MD/SDA/MUTE 4 VOUT2 OUTPUT AMP AND INETERFACE CONVERTER LOW-PASS FILTER VCOM SCK 5...
  • Page 55 HCD-G2BNiP/G2NiP – AMP Board – IC101 NJW1159V (TE2) IC102 BA6956AN OUTL 16 GND BOUTL 15 LATCH – 14 CLOCK INTERFACE & 13 DATA LOGIC VDD_OUT 12 CE1 CONTROL LOGIC 11 CE0 OUTR 10 INR BOUTR – VSS_OUT 9 INL LOSC...
  • Page 56 HCD-G2BNiP/G2NiP • IC Pin Function Description BD94DC BOARD IC101 TC94A70FG-101 (CD-MP3 PROCESSOR) Pin No. Pin Name Description AVSS3 Ground terminal RFZI RF ripple zero crossing signal input terminal RFRP RF ripple signal output terminal SBAD Sub beam addition signal output terminal...
  • Page 57 HCD-G2BNiP/G2NiP Pin No. Pin Name Description Micro controller interface mode selection signal input terminal Fixed at “H” in this unit DOUT Digital audio data output terminal Not used AOUT1 Audio data output to the DSP BCKO Bit clock signal output to the DSP...
  • Page 58 HCD-G2BNiP/G2NiP MAIN BOARD IC402 R5F3650NBDFA (SYSTEM CONTROLLER) Pin No. Pin Name Description DP SDA/SPI DOUT Serial data output to the fl uorescent indicator tube DP SCL Serial data transfer clock signal output to the fl uorescent indicator tube DP CS Chip select signal output to the fl...
  • Page 59 HCD-G2BNiP/G2NiP Pin No. Pin Name Description HP DET Headphone plug insert detection signal input terminal “H”: headphone plug is inserted HP MUTE Headphone muting on/off control signal output terminal “L”: muting on CDM OUT SW Disc tray open position detection switch input terminal “L”: disc tray is opened...
  • Page 60 HCD-G2BNiP/G2NiP Ver. 1.1 MAIN BOARD IC601 BU94604BKV-E2 (USB DRIVER) Pin No. Pin Name Description RESETX Reset signal input from the system controller “L”: reset SEL_SLAVE Mode setting terminal “L”: slave, “H”: stand alone Fixed at “L” in this unit Mode setting terminal “L”: MP1, MP2 and MP3 play, “H”: MP3 play only...
  • Page 61 HCD-G2BNiP/G2NiP MAIN BOARD IC805 BU9408KS2 (DSP) Pin No. Pin Name Description DVDDPLL Power supply terminal (+3.3V) FILT1 Filter connection terminal for the PLL DGNDPLL Ground terminal FILT2 Filter connection terminal for the PLL SCANTEST Digital test signal input terminal Not used...
  • Page 62: Exploded Views

    HCD-G2BNiP/G2NiP SECTION 6 EXPLODED VIEWS Note: • -XX and -X mean standardized parts, so • The mechanical parts with no reference The components identifi ed by mark 0 they may have some difference from the number in the exploded views are not sup- or dotted line with mark 0 are critical for original one.
  • Page 63: Front Panel Section

    HCD-G2BNiP/G2NiP Ver. 1.1 6-2. FRONT PANEL SECTION not supplied (FL-NET board) not supplied ND4102 not supplied not supplied (JOG2 board) S4322 S4321 S4301 not supplied (JOG1 board) included in S4322 included in S4321 Note 1: When replacing the rotary encoder (Ref. No. S4301 (JOG1 board),...
  • Page 64: Rear Panel Section

    HCD-G2BNiP/G2NiP 6-3. REAR PANEL SECTION not supplied not supplied ANT1 (G2BNiP) not supplied not supplied CN01 (G2BNiP) DAB1 not supplied F4401 not supplied (DAB board) not supplied not supplied supplied not supplied not supplied not supplied (LAN board) not supplied...
  • Page 65: Main Board Section

    HCD-G2BNiP/G2NiP Ver. 1.1 6-4. MAIN BOARD SECTION not supplied MOD1 supplied not supplied not supplied board supplied not supplied supplied F303 F304 not supplied supplied not supplied not supplied chassis section Ref. No. Part No. Description Remark Ref. No. Part No.
  • Page 66: Chassis Section

    HCD-G2BNiP/G2NiP 6-5. CHASSIS SECTION not supplied T901 CD mechanism deck section (CDM77B-K6BD94DC) supplied not supplied not supplied F951 not supplied DCDC board not supplied not supplied not supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark...
  • Page 67: Cd Mechanism Deck Section (Cdm77B-K6Bd94Dc)

    HCD-G2BNiP/G2NiP 6-6. CD MECHANISM DECK SECTION (CDM77B-K6BD94DC) not supplied not supplied (MOTOR board) not supplied (including sled motor, spindle motor) spindle motor sled motor S201 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark A-1242-967-B LOADING (BK) ASSY (Including MOTOR board)
  • Page 68: Electrical Parts List

    HCD-G2BNiP/G2NiP SECTION 7 ELECTRICAL PARTS LIST Note: • Due to standardization, replacements in • CAPACITORS When indicating parts by reference num- the parts list may be different from the uF: μF ber, please include the board name. parts specifi ed in the diagrams or the com- •...
  • Page 69 HCD-G2BNiP/G2NiP Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C1104 1-162-966-11 CERAMIC CHIP 0.0022uF D108 8-719-081-97 DIODE MMDL914T1 C1105 1-162-966-11 CERAMIC CHIP 0.0022uF D109 6-501-768-01 DIODE MAZ8120GMLS0 C1106 1-162-964-11 CERAMIC CHIP 0.001uF C1107 1-114-236-21 CERAMIC CHIP 22uF...
  • Page 70 HCD-G2BNiP/G2NiP Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < TRANSISTOR > R195 1-216-837-11 METAL CHIP 1/10W 0 R196 1-215-895-71 METAL OXIDE 3.3K Q018 8-729-038-23 TRANSISTOR RT1N141C-TP-1 0 R197 1-215-895-71 METAL OXIDE 3.3K Q104 8-729-620-07 TRANSISTOR...
  • Page 71 HCD-G2BNiP/G2NiP BD94DC Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark A-1857-582-A BD94DC BOARD, COMPLETE < CONNECTOR > *********************** CN202 1-784-833-51 CONNECTOR, FFC (LIF (NON-ZIF)) 21P < CAPACITOR > CN301 1-770-425-51 CONNECTOR, FFC/FPC 16P C101 1-164-677-11 CERAMIC CHIP 0.033uF <...
  • Page 72 HCD-G2BNiP/G2NiP BD94DC DCDC Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R221 1-216-845-11 METAL CHIP 100K 1/10W R4003 1-216-864-11 SHORT CHIP R222 1-216-845-11 METAL CHIP 100K 1/10W R4004 1-216-864-11 SHORT CHIP R223 1-216-845-11 METAL CHIP 100K...
  • Page 73 HCD-G2BNiP/G2NiP DCDC FL-NET Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark D956 6-500-334-01 DIODE MC2836-T112-1 R982 1-216-821-11 METAL CHIP 1/10W D957 6-502-969-01 DIODE DZ2J06800L R983 1-216-841-11 METAL CHIP 1/10W D958 6-503-022-01 DIODE DZ2J100M0L R988 1-216-864-11 SHORT CHIP...
  • Page 74 HCD-G2BNiP/G2NiP Ver. 1.1 FL-NET JOG1 JOG2 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R4102 1-218-446-11 METAL CHIP 1/10W < DIODE > R4103 1-216-826-11 METAL CHIP 2.7K 1/10W R4104 1-216-833-11 METAL CHIP 1/10W D4201 6-500-848-01 DIODE MC2840-T112-1...
  • Page 75 HCD-G2BNiP/G2NiP Ver. 1.1 JOG2 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < ROTARY ENCODE > C623 1-125-777-11 CERAMIC CHIP 0.1uF C626 1-125-777-11 CERAMIC CHIP 0.1uF S4321 1-418-725-51 ENCODER, ROTARY (12 TYPE) (TONE TREBLE) S4322...
  • Page 76 HCD-G2BNiP/G2NiP Ver. 1.1 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C870 1-164-870-11 CERAMIC CHIP 68PF C2425 1-164-882-11 CERAMIC CHIP 220PF C872 1-164-870-11 CERAMIC CHIP 68PF C2426 1-164-854-11 CERAMIC CHIP 15PF C873 1-125-777-11 CERAMIC CHIP 0.1uF...
  • Page 77 HCD-G2BNiP/G2NiP MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark IC706 6-708-913-01 IC TK73400AU3G0L-C R436 1-218-941-81 METAL CHIP 1/16W IC801 8-759-564-10 IC 74LVC157A-PW (G2BNiP) R437 1-218-941-81 METAL CHIP 1/16W IC802 6-712-740-01 IC PCM1681PWPR R438 1-218-941-81 METAL CHIP...
  • Page 78 HCD-G2BNiP/G2NiP Ver. 1.1 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R500 1-218-990-81 SHORT CHIP R562 1-218-990-81 SHORT CHIP R501 1-218-990-81 SHORT CHIP 0 (G2BNiP) R563 1-218-990-81 SHORT CHIP R502 1-218-990-81 SHORT CHIP 0 (G2BNiP)
  • Page 79 HCD-G2BNiP/G2NiP MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R628 1-218-965-11 METAL CHIP 1/16W R808 1-218-965-11 METAL CHIP 1/16W R629 1-218-965-11 METAL CHIP 1/16W (G2BNiP) R630 1-218-965-11 METAL CHIP 1/16W R809 1-218-935-11 METAL CHIP 1/16W...
  • Page 80 HCD-G2BNiP/G2NiP MAIN MOTOR Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R876 1-218-959-11 METAL CHIP 3.3K 1/16W R1421 1-218-990-81 SHORT CHIP R877 1-216-836-11 METAL CHIP 1/10W R1428 1-208-709-11 METAL CHIP 0.5% 1/16W R878 1-218-990-81 SHORT CHIP...
  • Page 81 HCD-G2BNiP/G2NiP Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C5016 1-117-681-11 ELECT CHIP 100uF R5011 1-216-864-11 SHORT CHIP C5017 1-107-826-11 CERAMIC CHIP 0.1uF R5012 1-216-864-11 SHORT CHIP C5018 1-164-854-11 CERAMIC CHIP 15PF R5013 1-218-990-81 SHORT CHIP...
  • Page 82 HCD-G2BNiP/G2NiP SUB-PT TUNER Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R5087 1-218-831-11 METAL CHIP 0.5% 1/10W < DIODE > R5088 1-218-990-81 SHORT CHIP D4401 6-500-335-01 DIODE MC2838-T112-1 R5089 1-218-990-81 SHORT CHIP D4402 6-500-335-01 DIODE MC2838-T112-1...
  • Page 83 HCD-G2BNiP/G2NiP TUNER Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < IC > 1-481-530-21 FILTER, CLAMP (FERRITE CORE) 1-839-670-21 CABLE, FLEXIBLE FLAT (8 CORE) (G2BNiP) IC4501 6-717-268-01 IC RZ5B800-0002E2 1-839-671-21 CABLE, FLEXIBLE FLAT (9 CORE) < JUMPER RESISTOR >...
  • Page 84 Description of Revision 2011.10 2012.03 Addition of AEP model (HCD-G2BNiP) Change of HP, JOG1, JOG2, SUB-PT, TUNER and USB boards (Suffi x-12) Change of Part for Ref. No. IC601 on the MAIN board Change of Part for Ref. No. S4301 on the JOG1 board Change of Part for Ref.

This manual is also suitable for:

Hcd-g2nip

Table of Contents