Huawei SUN2000-12KTL Quick Manual
Hide thumbs
Also See for SUN2000-12KTL:
- User manual (138 pages) ,
- Quick manual (22 pages) ,
- Quick installation manual (12 pages)
Related Manuals for Huawei SUN2000-12KTL
Summary of Contents for Huawei SUN2000-12KTL
- Page 1 SUN2000-(8KTL-12KTL) and SUN2000-(3KTL- 20KTL)-M0 Replacement Quick Guide Issue: 04 Part Number: 31500EPF Date: 2021-11-22 HUAWEI TECHNOLOGIES CO., LTD.
- Page 2 Removing Cables from SUN2000-(8KTL–12KTL) for Future Use 1. Power off the SUN2000 to be replaced. 2. Remove the AC connector and remove the AC output power cable from the mating socket for future use. Copyright © Huawei Technologies Co., Ltd. 2021. All rights reserved.
- Page 3 3. Remove the DC connectors and use a cable cutter to cut off the terminals of DC input power cables. Set the cables aside for future use. The DC terminals of SUN2000-(8KTL–12KTL) must be cut off. If the DC connectors of SUN2000- (8KTL–12KTL) are directly connected to SUN2000-(8KTL–12KTL)-M2, the SUN2000 may be burnt.
- Page 4 Removing SUN2000-(8KTL–12KTL) 2. Remove the two hexagonal screws. 1. (Optional) Open the anti-theft lock. 3. Remove the SUN2000 from the rear panel. 4. Remove the nuts, spring washers, and flat washers, and then remove the rear panel.
- Page 5 Installing SUN2000-(8KTL–20KTL)-M2 The installation of the new rear panel is the same as that of the SUN2000-(8KTL–12KTL) rear panel. Align the mounting holes. 1. Install the new rear panel. 2. Install the mounting bracket. 3. Install the SUN2000 onto the mounting bracket. (Optional) Install an anti- theft lock.
- Page 6 Installing the PE Cable for SUN2000-(8KTL–20KTL)-M2 Before connecting cables, ensure that the DC switch on the SUN2000 and all the switches connected to the SUN2000 are set to OFF. Otherwise, the high voltage of the SUN2000 may result in electric shocks. It is recommended that silica gel or paint be applied around the ground terminal after the PE cable is connected.
- Page 7 Five-Core Cable (L1, L2, L3, N, and PE) • This section describes how to connect a five-core AC output power cable to an AC connector. • A three-core AC output power cable can be connected similarly. The three-core cable (L1, L2, and L3) is not connected to the N terminal or PE terminal.
- Page 8 Installing DC Input Power Cables for SUN2000-(8KTL–20KTL)-M2 1. Ensure that the PV module output is well insulated to ground. 2. Use the positive and negative Staubli MC4 metal terminals and DC connectors supplied with the SUN2000. Using incompatible positive and negative metal terminals and DC connectors may result in serious consequences.
- Page 9 Pull the DC input power cables back to Click ensure that they are connected securely. Extension cables for DC terminals Installing the Signal Cable for SUN2000-(8KTL–20KTL)-M2 Communications Port Signal Definitions for SUN2000-(8KTL–12KTL) Color Pin Description Ensure that the protective White and orange RS485A, RS485 differential signal+ layer of the cable is inside Orange...
- Page 10 Terminals for the Signal Cable The figures show the RJ45 connector when the surface without the fastener faces upwards. If the colors and functions of the wires are different, connect the wires based on their functions. (Optional) Connecting RS485 Communications Cables (SUN2000 Cascading) 1.
-
Page 11: Post-Installation Check
2. Connect the signal cable connector to the communications port. Communications port (COM) Checking the Installation of SUN2000-(8KTL–20KTL)-M2 and Powering On the SUN2000 Post-installation Check No. Acceptance Criterion The SUN2000 is installed correctly and securely. The cables are routed properly as required by the customer. The communications expansion module is installed correctly and securely. - Page 12 Commissioning SUN2000-(8KTL–12KTL)-M2 1. Downloading the App Method 1: Search for FusionSolar on Huawei AppGallery and download the latest installation package. Method 2: Access https://solar.huawei.com using the mobile phone browser and download the latest installation package. Method 3: Scan the following QR code and download the latest installation package.
- Page 13 3. Connect to the solar inverter WLAN and log in as installer to access the device commissioning screen. At the first login, the Quick settings screen is displayed by default. Exit the quick settings. 4. Choose Maintenance > Device replacement, select the type of the original device, and complete the replacement.
- Page 14 5. (Optional) If you need to set other parameters, tap Settings. 6. Connect the SUN2000 to the management system. SmartLogger1000 Networking Choose Maintenance, log in to the SmartLogger1000 as Advanced User or Special User, and choose Device Mgmt. to connect the new SUN2000 to the system. Connect the new SUN2000 to the system.
- Page 15 SmartLogger1000A/SmartLogger3000 Networking Connect to the SmartLogger WLAN. Log in to the app as Advanced User or Special User for the SmartLogger1000A, or as Installer for the SmartLogger3000. Choose Maintenance > Device Mgmt. to connect the new SUN2000 to the system. Connect the new SUN2000 to the system.
- Page 16 You can also manage devices on the SmartLogger WebUI. Log in to the SmartLogger WebUI as Advanced User or Special User for the SmartLogger1000 or SmartLogger1000A, or as an admin user for the SmartLogger3000. Choose Maintenance > Connect Device to connect the new SUN2000 to the system.
- Page 17 You can also complete historical data inheritance in the FusionSolar app. Log in to the app and choose Device management > Device Replacement to replace the SN of the old SUN2000 with the SN of the new SUN2000. The historical data of the old SUN2000 will be inherited.
- Page 18 SUN2000-(8KTL–20KTL)-M0 Replacement Scenario Remove SUN2000- Install SUN2000- Perform SUN2000-(8KTL– Start (8KTL–20KTL)-M0. (8KTL–20KTL)-M2. 20KTL)-M2 electrical connections. Perform the SUN2000-(8KTL– Check the installation and 20KTL)-M2 deployment wizard. power on the SUN2000. Removing SUN2000-(8KTL–20KTL)-M0 • Before removing the original SUN2000, ensure that the DC switch on the SUN2000 and all the switches connected to the SUN2000 are set to OFF.
- Page 19 4. (Optional) Remove the Smart Dongle for future use. • This section describes how to remove a WLAN-FE Smart Dongle. • The 4G Smart Dongle and WLAN Smart Dongle can be removed similarly. 5. Remove the signal cable connector for future use. Smart Dongle port (GPRS/4G/WLAN) Communications port (COM) 6.
- Page 20 Install SUN2000-(8KTL–20KTL)-M2 1. Install the SUN2000 onto the mounting bracket. 2. (Optional) Install an anti-theft lock. Performing SUN2000-(8KTL–20KTL)-M2 Electrical Connections Before connecting cables, ensure that the DC switch on the SUN2000 and all the switches connected to the SUN2000 are set to OFF. Otherwise, the high voltage of the SUN2000 may result in electric shocks.
- Page 21 3. Install DC input power cables. 1. Ensure that the PV module output is well insulated to ground. 2. Use the positive and negative Staubli MC4 metal terminals and DC connectors supplied with the SUN2000. Using incompatible positive and negative metal terminals and DC connectors may result in serious consequences.
- Page 22 Pull the DC input power cables back to Click ensure that they are connected securely. Extension cables for DC terminals 4. (Optional) Install the Smart Dongle. • If a Smart Dongle is configured, it is recommended that you install it before connecting the signal cable.
- Page 23 See section 1.7 "Checking the Installation of SUN2000-(8KTL–20KTL)-M2 and Powering On the SUN2000". Commissioning SUN2000-(8KTL–12KTL)-M2 1. Downloading the App Method 1: Search for FusionSolar on Huawei AppGallery and download the latest installation package. Method 2: Access https://solar.huawei.com using the mobile phone browser and download the latest installation package.
- Page 24 3. Connect the SUN2000 to the management system. Smart Dongle Networking Scenario A. Connect to the solar inverter WLAN and log in as installer to access the device commissioning screen. tap Quick settings to complete the deployment of the new SUN2000 as prompted. At the first login, the Quick settings screen is displayed by default.
- Page 25 SmartLogger1000A/SmartLogger3000 Networking A. Connect to the SmartLogger WLAN. Log in to the app as Advanced User or Special User for the SmartLogger1000A, or as Installer for the SmartLogger3000. Choose Maintenance > Device Mgmt. to connect the new SUN2000 to the system. Connect the new SUN2000 to the system.
- Page 26 You can also manage devices on the SmartLogger WebUI. Log in to the SmartLogger WebUI as Advanced User or Special User for the SmartLogger1000A, or as an admin user for the SmartLogger3000. Choose Maintenance > Connect Device to connect the new SUN2000 to the system.
- Page 27 4. Log in to the SmartPVMS and navigate to the Device Management page to replace the SN of the old SUN2000 with the SN of the new SUN2000. The historical data of the old SUN2000 will be inherited. You can also complete historical data inheritance in the FusionSolar app.
- Page 28 SUN2000-(3KTL–10KTL)-M0 Replacement Scenario Remove SUN2000- Install SUN2000- Perform SUN2000-(3KTL– Start (3KTL–10KTL)-M0. (3KTL–10KTL)-M1. 10KTL)-M1 electrical connections. Perform the SUN2000-(3KTL– Check the installation and 10KTL)-M1 deployment wizard. power on the SUN2000. • The methods for removing the SUN2000-(3KTL-10KTL)-M0 and SUN2000-(8KTL-20KTL)-M0 are the same. For details, see section 2 ''SUN2000-(8KTL–20KTL)-M0 Replacement Scenario.'‘ •...
- Page 29 Assembling DC Connectors Positive connector Positive metal terminal PV-CZM-22100/19100 (Staubli) Negative Ensure that the cable connector Click Negative metal terminal cannot be pulled out after being crimped. Use the wrench Ensure that cable shown in the figure to polarities are correct. tighten the locking nut.
- Page 30 Huawei Technologies Co., Ltd. Huawei Industrial Base, Bantian, Longgang Shenzhen 518129 People's Republic of China solar.huawei.com...