Related Manuals for Toro 74352
Summary of Contents for Toro 74352
- Page 1 Form No. 3353-200 Rev B Z480 TimeCutter Z Riding Mower Model No. 74352—Serial No. 250000001 and Up Operator’s Manual Register your product at www.Toro.com Original Instructions (EN)
-
Page 2: Table Of Contents
Starting and Stopping the Engine ... . . Dealer or Toro Customer Service and have the model and Operating the Power Take Off (PTO) .. -
Page 3: Safety
Safe Operating Practices The following instructions are from ANSI standard B71.1—2003. This product is capable of amputating hands and feet and throwing objects. Always follow all safety instructions to avoid serious injury or death. General Operation m–8112 • Read, understand, and follow all instructions in the Figure 1 operator’s manual and on the machine before starting. - Page 4 Children • Always wear eye protection when operating the mower. • Data indicates that operators, age 60 years and above, Tragic accidents can occur if the operator is not alert to the are involved in a large percentage of riding presence of children.
-
Page 5: Toro Riding Mower Safety
• Check for proper brake operation frequently. Adjust and service as required. • Maintain or replace safety and instruction decals as necessary. • Use only genuine Toro replacement parts to ensure that original standards are maintained. -
Page 7: Slope Chart
Slope Chart... -
Page 9: Safety And Instruction Decals
Replace any decal that is damaged or lost. Note: If needed, a Decal Kit, 108–6110, and French manual are available. Order the Decal Kit from the Toro Parts Department and the French manual from either the Toro Parts Department or online at www.toro.com. - Page 10 98-3798 108-6109 1. To push the machine, move bypass levers forward and then out to lock them into position Battery Symbols Some or all of these symbols are on your battery. 106-8716 1. Explosion hazard 7. Wear eye protection; explosive gases can 2.
-
Page 11: Gasoline And Oil
Gasoline and Oil Recommended Gasoline Warning Use UNLEADED Regular Gasoline suitable for automotive use (87 pump octane minimum). Leaded regular gasoline Gasoline is harmful or fatal if swallowed. may be used if unleaded regular is not available. Long–term exposure to vapors can cause serious injury and illness. -
Page 12: Operation
Operation Controls Become familiar with all of the controls (Fig. 3 and 4) Note: Determine the left and right sides of the machine before you start the engine and operate the machine. from the normal operating position. Think Safety First Please carefully read all of the safety instructions and decals in the safety section. -
Page 13: Operating The Power Take Off (Pto)
2. Move the PTO (power take off) to Off (Fig. 5). 2. Move the PTO to Off (Fig. 5). 3. Turn the ignition key to Off (Fig. 7). 4. Pull the wire off of the spark plug(s) to prevent the possibility of someone accidentally starting the machine before transporting or storing the machine. -
Page 14: Testing The Safety Interlock System
Understanding the Safety Interlock Forward System 1. Move the levers to the center, unlocked position. The safety interlock system is designed to prevent the 2. To go forward, slowly push the motion control levers engine from starting unless: forward (Fig. 9). •... -
Page 15: Adjusting The Height Of Cut
Positioning the Seat Warning The seat can move forward and backward. Position the seat where you have the best control of the machine and are Children or bystanders may be injured if they most comfortable. move or attempt to operate the mower while it is unattended. -
Page 16: Adjusting The Motion Control Levers
Adjusting the Motion Control Levers The motion control levers can be adjusted higher or lower for maximum operator comfort. 1. Remove the 2 bolts holding the control lever to the control arm shaft (Fig. 12). 2. Move the control lever to the next set of holes. Secure the lever with the 2 bolts (Fig. -
Page 17: Removing And Installing The Engine Hood
Removing and Installing the Danger Engine Hood Without the grass deflector, discharge cover, or 1. To remove the hood, loosen the knobs and then pull the complete grass catcher assembly mounted in place, hood back and up (Fig. 15). you and others are exposed to blade contact and thrown debris. - Page 18 File down any nicks and sharpen the blades as necessary. If a blade is damaged or worn, replace it immediately with a genuine Toro replacement blade. Safe Towing Practices Tow only with a machine that has a hitch designed for towing.
-
Page 19: Maintenance
Maintenance Note: Determine the left and right sides of the machine from the normal operating position. Recommended Maintenance Schedule Maintenance Service Maintenance Procedure Interval • Check the engine oil level. Each use • Check the safety system. • Clean the mower housing. After first 5 hours •... -
Page 20: Servicing The Engine Oil
Servicing the Engine Oil Check the oil level daily or after every 8 hours. Change the oil after the first 5 operating hours and every 50 operating hours thereafter. Oil Type: Detergent oil (API service SF, SG, SH, SJ, or higher) Crankcase Capacity: •... -
Page 21: Servicing The Air Cleaner
3. Disengage the PTO and set the parking brake. 2. Remove the old filter and wipe the filter adapter gasket surface (Fig. 20). 4. Stop the engine, remove the key, and wait for all moving parts to stop before leaving the operating 3. -
Page 22: Servicing The Spark Plug
Important Replace the foam element if it is torn or worn. Cleaning the Paper Element: 1. Lightly tap the element on a flat surface to remove dust and dirt. 2. Carefully clean the rubber seal on the paper element to prevent debris from entering the engine. -
Page 23: Servicing The Cutting Blades
Check the cutter blades daily for sharpness, and for any wear or damage. File down any nicks and sharpen the blades as necessary. If a blade is damaged or worn, replace it immediately with a genuine Toro replacement blade. For m–7875 convenient sharpening and replacement, you may want to Figure 23 keep extra blades on hand. - Page 24 Figure 29 optimum performance and continued safety conformance of 1. Blade 2. Balancer the machine, use genuine Toro replacement blades. Replacement blades made by other manufacturers may result in non-conformance with safety standards. Installing the Blades Hold the blade end using a rag or thickly-padded glove.
-
Page 25: Greasing And Lubrication
Greasing the Bearings Important The curved part of the blade must be pointing upward toward the inside of the mower to ensure 1. Park the machine on a level surface and disengage the proper cutting. blade control (PTO). 2. Install the small flat washer, and the blade nut (Fig. 27). 2. - Page 26 Removing the Battery Warning Battery terminals or metal tools could short against metal machine components causing sparks. Sparks can cause the battery gasses to explode, resulting in personal injury. • When removing or installing the battery, do not allow the battery terminals to touch any metal parts of the machine.
- Page 27 1. Tip the seat forward to see the battery. 1. Remove the battery from the chassis; refer to Removing the Battery, page 26. 2. Look at the side of the battery. The electrolyte must be up to the Upper line (Fig. 33). Do not allow the 2.
-
Page 28: Draining The Fuel Tank
3. Close the fuel shut-off valve located under the front of 6. Install a new filter and move the hose clamps close to the fuel tank. the filter (Fig. 35). 4. Loosen the hose clamp at the fuel filter and slide it up 7. -
Page 29: Adjusting The Front-To-Rear Blade Slope
Adjusting the Front-to-Rear m–8121 Blade Slope Check the front-to-rear blade level any time you install the mower. If the front of the mower is more than 5/16 inch (7.9 mm) lower than the rear of the mower, adjust the blade level using the following instructions: 1. -
Page 30: Inspecting The Belts
8. Set the height-of-cut at position 2.5 [2.5 inch (64 mm)] and carefully rotate the blades so they are facing front to rear (Fig. 40). 9. Measure from the tip of the front blade to the flat surface and the tip of the rear blade to the flat surface (Fig. -
Page 31: Replacing The Mower Belt
Removing the Mower Warning Note: Before removing the mower, make a note for which holes are used in the leveling brackets (Fig. 44). The spring is under tension when installed and can cause personal injury. 1. Park the machine on a level surface and disengage the blade control (PTO). -
Page 32: Installing The Mower
7. Slide the mower rearward to remove the mower belt from the engine pulley. 8. Slide the mower out from underneath the machine. Note: Retain all parts for future installation. Installing the Mower 1. Park the machine on a level surface and disengage the blade control (PTO). -
Page 33: Replacing The Grass Deflector
4. Lower the mower to the lowest height-of-cut. 5. Sit on the seat and start the engine. Engage the PTO and let the mower run for one to three minutes. 6. Disengage the PTO, stop the engine, and remove the ignition key. -
Page 34: Wiring Diagram
Wiring Diagram (IGNITION) KEY SWITCH PN 88–9830 WIRE COLOR CODES NO CONNECTION B I A AND X Y PINK BLACK START B I S BROWN BLUE GREEN VIOLET TERMINAL VIEW FROM GREY WHITE BACK OF SWITCH ORANGE YELLOW KEY SW REGULATOR (PTO) FUEL SOLENOID... -
Page 35: Cleaning And Storage
Cleaning and Storage crank the engine and distribute the oil inside the cylinder. Install the spark plug(s). Do not install the wire on the spark plug(s). 1. Disengage the PTO, set the parking brake, stop the engine, and remove the key. 12. -
Page 36: Troubleshooting
Troubleshooting Problem Possible Causes Corrective Action The engine overheats. 1. The engine load is excessive. 1. Reduce ground speed. 2. The oil level in the crankcase is 2. Add oil to the crankcase. low. 3. The cooling fins and air 3. - Page 37 Problem Possible Causes Corrective Action The engine loses power. 1. The engine load is excessive. 1. Reduce ground speed. 2. The air cleaner is dirty. 2. Clean the air cleaner element. 3. The oil level in the crankcase is 3. Add oil to the crankcase. low.
- Page 38 Problem Possible Causes Corrective Action The blades do not rotate. 1. The drive belt is worn, loose or 1. Install a new drive belt. broken. 2. The drive belt is off of the 2. Install the drive belt and check pulley.
-
Page 40: The Toro Total Coverage Guarantee
If for any reason you are dissatisfied with your Distributor’s service or have difficulty obtaining guarantee information, contact the Toro importer. If all other remedies fail, you may contact us at Toro Warranty Company.