Sealey VSE6198 Quick Start Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Wear eye
instruction protection
manual
1. SAFETY
i
WARNING! Wear approved eye protection. Wear appropriate Personal Protective Equipment. A full range of Personal Protective
‰
Equipment is available from your Sealey stockist.
WARNING! Ensure that Health & Safety, Local Authority Regulations and general workshop practice Regulations are adhered to when
‰
using tools.
DO NOT use tools if damaged.
8
Maintain tools to ensure that they are in an adequate condition for safe use and optimum performance.
9
Ensure that a vehicle that has been raised by a jack is adequately supported. Use axle stands.
9
DO NOT attempt to start or move a vehicle whilst in gear and with timing devices fitted.
8
Wear suitable clothing to avoid snagging. DO NOT wear jewellery. Tie back long hair.
9
Account for all tools, parts and components being used. DO NOT leave these in or near the engine. Return tools to suitable storage
9
after use.
When not in use, store in a safe, dry childproof place.
9
Keep children and unauthorised persons away from the work area.
9
▲ IMPORTANT! These instructions are intended as a guide only. Always refer to the vehicle manufacturer's service instructions or a
proprietary manual to establish the correct procedure and data.
WARNING! The warnings, conditions and instructions in this manual cannot cover all possible conditions and situations. The Operator/
‰
User must apply caution and common sense (good practical sense).
When timing an engine, always prevent the engine from being turned over. Use a notice and/or inhibit the engine.
9
WARNING! Incorrect or out of phase camshaft timing can result in contact between the valve head and the piston crown. This will
‰
cause damage to the engine.
2. INTRODUCTION
Suitable for BMW N20 and N26 2.0L engines. Use in conjunction with VSE6188 Timing Tool Kit. Supplied in a storage case with
instructions.
3. CONTENTS
Item Sealey Part Description
No.
1 VSE6198.01 Sprocket locking tool + bolts
2 VSE6198.02 Balance shaft locking tool
3 VSE6198.03 Tensioner locking pin
Associated tools
VSE6188 Timing tool kit
4. APPLICATIONS
Models:
BMW 1 Series: 125i (12-16)
BMW 2 Series: 220i Coupe F22; 228i (14-16), 220i Coupe (14-16), 228i Coupe (14-16), 220i Cabriolet (15-16
BMW 3 Series: 320i xDrive (12-16), 328i (12-15), 328i xDrive (12-15)
BMW 4 Series: 420i F32 x-Drive Coupe (13-16), x-Drive Gran Coupe (14-16), 420i F33 Cabriolet (14-16)
BMW 5 Series: 520i (11-17), 528i xDrive (11-17)
BMW X1: xDrive 20i(11-15), sDrive 20i(11-15), xDrive 28i(11-15)
BMW X3: xDrive 20i (11-17)
BMW X4: xDrive 40i (14-18)
BMW Z4: sDrive 20i (11-17), sDrive 28i (11-16)
© Jack Sealey Limited
BMW OIL PUMP AND BALANCE SHAFT
ALIGNMENT KIT
VSE6198
MODEL NO:
OEM Number
22-12-825
23-18-117
11-4-120
Original Language Version
Engine codes:
2.0
N20B20,
N20B20A,
N20B20B,
N20B20/UO,
N20B20O0,
N26B20
VSE6198 Issue 1 10/09/20