Related Manuals for Fujitsu S540
Summary of Contents for Fujitsu S540
- Page 1 Thin Client Operating Manual FUJITSU Thin Client FUTRO S540 FUJITSU Thin Client FUTRO S740...
- Page 2 Thank you for buying an innovative product from Fujitsu. Latest information about our products, useful tips, updates etc. is available on our website: "http://www.fujitsu.com/fts/" You can find driver updates at: "http://support.ts.fujitsu.com/download" Should you have any technical questions, please contact: •...
- Page 4 Published by / Contact address in the EU Fujitsu Technology Solutions GmbH Mies-van-der-Rohe-Straße 8 80807 Munich, Germany "http://www.fujitsu.com/fts/" Copyright © Fujitsu Technology Solutions GmbH 2019. All rights reserved. Publication Date 02/2019 Order No.: A26361-K1080-Z320-1-7619, edition 2...
- Page 5 FUJITSU Thin Client FUTRO S540 FUJITSU Thin Client FUTRO S740 Operating Manual Your FUTRO... Ports and Operating Elements Important notes Getting started Operation System expansions Technical data Index...
- Page 6 Information on the product description meets the design specifications of Fujitsu and is provided for comparison purposes. Several factors may cause the actual results to differ. Technical data is subject to change without prior notification. Fujitsu rejects any responsibility with regard to technical or editorial mistakes or omissions.
-
Page 7: Table Of Contents
Opening the casing ..............30 Fujitsu... - Page 8 FUJITSU Thin Client FUTRO S540 / S740 ........
-
Page 9: Your Futro
The operating system is installed on a flash memory. Validity of the Reference Manual This Reference Manual is valid for the following system: • FUJITSU Thin Client FUTRO S540 • FUJITSU Thin Client FUTRO S740 Notational conventions Pay particular attention to text marked with this symbol. Failure to observe these warnings could pose a risk to health, damage the device or lead to loss of data. -
Page 10: Ports And Operating Elements
Front view Onswitch Offswitch Headphoneport Microphone jack USB, 1 = ON/OFF switch 3 = Headphone port 2 = USB 3.1 Gen1 ports (USB Type-A) 4 = Microphone jack Fujitsu... -
Page 11: Rear View
7 = Audio output (Line out) optional) with double screw security 8 = DisplayPort Device with Power-over-Ethernet 9 = DC input jack (DC IN) module: No port 3 = USB 2.0 ports (USB Type-A) 4 = Security Lock fixture (positioned at the side) Fujitsu... -
Page 12: Security Functions
You can use the security lock device (positioned at the side) and the Kensington Lock cable (steel cable, accessory) to protect your device against theft. Please consult the manual for your security lock. When using the Security Lock device, opening of the casing is also prevented. Fujitsu... -
Page 13: Securing Usb Covers (Optional)
Please note that USB covers, once fitted, cannot be removed again! Ensure that you fit the USB covers the right way round. ► Insert the USB covers in the USB ports on the front of the device and push the USB covers in firmly. Fujitsu... - Page 14 ► Insert the USB covers in the USB ports on the rear side of the device and push the USB covers in firmly. In the BIOS Setup, under Advanced - USB Port Security, you can also deactivate the USB ports, in order to limit the use of USB devices. Fujitsu...
-
Page 15: Important Notes
Make sure that the rated current of the mains adapter is not higher than that of the power system to which you connect the mains adapter. ON/OFF switches do not disconnect the device from the mains voltage. To completely disconnect the mains voltage, remove the power plug from the power socket. Fujitsu... -
Page 16: Module
Important notes on preparing your FUTRO S740 for use via the Power-over-Ethernet module With the help of the Power-over-Ethernet module, you can operate the FUTRO S540/S740 over the LAN without any additional power supply. You will need a suitable network infrastructure for this. -
Page 17: Energy Saving, Disposal And Recycling
Energysaving Recycling You can find information on these subjects in the "Environment and Energy Information" manual or on our website ("http://www.fujitsu.com/fts/about/fts/environment-care/"). Information on "Ecodesign directive": Regulation 1275/2008, based on the EU Eco-design Directive (2009/125/EU), defines requirements for the power consumption of electrical and electronic domestic and office devices in stand-by and off mode. -
Page 18: Getting Started
If the device is to be built-in, adequate ventilation must be assured. Fit the base feet for horizontal or vertical operation (see "Vertical operating position", Page 15 "Horizontal operating position", Page 17). Fujitsu... -
Page 19: Vertical Operating Position
► Place the feet on the casing (1). In doing so, make sure that the 4 clips (2) on the feet are aligned above the corresponding holes in the casing. ► To secure the feet, press the clips in the direction of the arrow (2) until they are felt to engage in the holes. Fujitsu... - Page 20 M2.5x5 mm. These are not included in the delivery scope. ► Secure the feet with the screws (3). ► Stand the device on the feet. ► If necessary, reconnect any cables that were previously disconnected. Fujitsu...
-
Page 21: Horizontal Operating Position
To protect your device against unauthorised removal of the feet, the feet can also be secured with two screws, each of type M2.5x5 mm. These are not included in the delivery scope. ► Secure the feet with the screws (3). Fujitsu... - Page 22 Getting started ► Place the device on the feet. ► If necessary, reconnect any cables that were previously disconnected. Fujitsu...
-
Page 23: Connecting External Devices
► Follow the instructions contained in the monitor manual to prepare the monitor for operation (e.g. connecting cables). Monitor, ► Connect the data cable to the required monitor port on your device. ► Plug the monitor power cable into the grounded mains outlet. Fujitsu... -
Page 24: Connecting A Usb Mouse
The devices connected to the serial interface require drivers. Your operating system already includes many drivers. If the required drive is missing, install it. The latest drivers are usually available on the Internet or will be supplied on a data carrier. Fujitsu... -
Page 25: Connecting External Devices To The Usb Ports
Connect microphone and headphones Microphone Headphones ► Connect the microphone to the microphone port. ► Connect the headphones to the headphones port. Connecting the device to the network (LAN) ► Connect the 10/100/1000 Base T network cable to the RJ45 LAN port. Fujitsu... -
Page 26: Connecting The Mains Adapter
► Connect the mains cable (1) to the mains adapter. ► Connect the mains adapter cable (2) to the DC jack (DC IN) of the device. ► Plug the mains cable (3) into a mains socket. Fujitsu... -
Page 27: Operation
Citrix and Microsoft clients as well as the optional VMware client. It has a user-friendly licence model, with the possibility of transferring licences to new devices. Updates for eLux® can be found on the Fujitsu support pages or on the Internet at "www.myelux.com". -
Page 28: Windows® 10 Iot Enterprise
The write protect filter is not enabled in the delivery state, to make it easier to adapt the thin client to your requirements. Fujitsu strongly advises that the write protect filter should be enabled during normal operation, because only then is the typical thin client high security of the device guaranteed. -
Page 29: Scout Enterprise Management Suite® - The Management Solution For Thin Clients
• Support of Wake-On-LAN and Remote Power On/Off Mirroring of desktops, encrypted and audit-proof • • Extensive diagnostic information For more information on Scout Enterprise, go to "http://www.unicon-software.com/produkte/scout-enterprise/". More information and manuals are available on the Internet at "http://www.unicon-software.com/udocs". Fujitsu... -
Page 30: Switching Off The Device
BIOS Setup will be started. Select one of the tabs to access other setting options in BIOS Setup. PXE system boot PXEsystem boot ► Switch the device on with the ON/OFF switch. ► When starting the system, press the key several times. The boot menu is displayed. ► Select the desired boot option. Fujitsu... -
Page 31: Bios Update
BIOS Update When should a BIOS update be performed? Fujitsu Technology Solutions makes new BIOS versions available to ensure compatibility with new operating systems, new software or new hardware. In addition, new BIOS functions can be integrated. A BIOS update should also always be performed if there is a problem that cannot be solved using new drivers or new software. -
Page 32: System Expansions
When installing components that become very hot, make sure that the maximum permissible temperature of the components in operation is not exceeded. It may be necessary to update the BIOS when carrying out a system expansion or hardware upgrade. For additional information, refer to the section "BIOS Update", Page Fujitsu... -
Page 33: Information About Boards
The equipment and tools you use must be free of static charges. • Only touch or hold the boards by the edge or, if present, at the areas marked green (Touch Points). • Never touch pins or conductors on boards fitted with ESDs. Fujitsu... -
Page 34: Opening The Casing
Please observe the safety information in "Important notes", Page Disconnect the mains plug from the mains outlet. Only insert the power plug after you have closed the casing. ► Remove any connected wires which are in the way. Horizontal operating position: Fujitsu... - Page 35 System expansions Vertical operating position: ► To remove the feet, undo the screws (1), open the clips (2) and lift the feet away from the device (3). Fujitsu...
- Page 36 System expansions ► Undo the screws (4). ► Slide the casing cover in the direction of the arrow (5) as far as it will go. ► Lift the casing cover off the casing in the direction of the arrow (6). Fujitsu...
-
Page 37: Adding Memory
Installing a memory module ► Insert the memory module with the contacts and the recess (a) facing the slot (1). Memory expansion Memory module ► Carefully push the memory module downwards until you feel it click into place (2). Fujitsu... -
Page 38: Install And Remove Loudspeaker
"Opening the casing", Page 30). ► To release the front panel, press the front panel down slightly (1) at the level of the catches (a). ► Lift the front cover from the casing in the direction of the arrow (2). Fujitsu... - Page 39 System expansions ► Place the loudspeaker in the front panel (3). ► Guide the loudspeaker cable through the opening (b) and into the casing. ► Connect the loudspeaker cable to the connector on the mainboard (4). Fujitsu...
- Page 40 ► Place the catches (a) in the corresponding openings in the casing. ► Press the front panel in the direction of the arrow (5) until the catches (a) are felt to engage in the casing. ► Refit the casing cover on the casing (see chapter "Closing the casing", Page 49). Fujitsu...
-
Page 41: Removing The Loudspeaker
► To release the front panel, press the front panel down slightly (2) at the level of the catches (a). ► Lift the front panel a few centimetres away from the casing in the direction of the arrow (3). In doing so, be careful not to damage the loudspeaker cable. Fujitsu... - Page 42 System expansions ► Guide the loudspeaker cable through the opening (b) and out of the casing. ► Remove the loudspeaker from the front panel (4). ► Place the catches (a) in the corresponding openings in the casing. Fujitsu...
-
Page 43: Install And Remove Usb Port
► Secure the USB port using the 2 x M2.5 screws provided (3), max. torque 0,4 Nm. ► Connect the cable of the USB port to the connector on the mainboard (3). ► Refit the casing cover on the casing (see chapter "Closing the casing", Page 49). Fujitsu... -
Page 44: Remove Usb Port
► Disconnect the cable of the USB port from the connector on the mainboard (1). ► Undo the screws (2) on the USB port. ► Remove the USB port (3). ► Refit the casing cover on the casing (see chapter "Closing the casing", Page 49). Fujitsu... -
Page 45: Installing And Removing A Power Over Ethernet Module (Optional)
Installing the Power over Ethernet module Power overEthernetmodule, ► Open the casing (see "Opening the casing", Page 30). ► Remove the cover of the pin connector (1). Keep the cover carefully in a safe place. This must be reattached when removing the Power-over-Ethernet module. Fujitsu... - Page 46 ► Carefully press the Power-over-Ethernet module on the pin connectors at the points marked (2) in the Figure. Ensure that it engages in the slot. ► Close the casing (see "Closing the casing", Page 49). Fujitsu...
-
Page 47: Removing The Power Over Ethernet Module
System expansions Removing the Power over Ethernet module Power overEthernetmodule, ► Open the casing (see "Opening the casing", Page 30). ► Pull the Power-over-Ethernet module from the pin connector (1). Fujitsu... - Page 48 System expansions ► Place the cover on the pin connector (2). ► Close the casing (see "Closing the casing", Page 49). Fujitsu...
-
Page 49: Install And Remove Serial Port
Dispose of the removed sheet metal plate according to the national regulations. ► Position the serial port on the inside of the device at the flagged location (2). ► Secure the serial port using the 2 x M2.5 bolts provided (3), max. torque 0,4 Nm. Fujitsu... - Page 50 System expansions ► Connect the cable of the serial port to the connector on the mainboard (4). ► Refit the casing cover on the casing (see chapter "Closing the casing", Page 49). Fujitsu...
-
Page 51: Remove Serial Port
► Disconnect the cable of the serial port from the connector on the mainboard (1). ► Undo the bolts (2) on the serial port. ► Remove the serial port (3). ► Refit the casing cover on the casing (see chapter "Closing the casing", Page 49). Fujitsu... -
Page 52: Replacing The Lithium Battery
► Press the catch in the direction of the arrow (1). The battery jumps out of the holder slightly. ► Remove the battery (2). ► Push the new lithium battery of the identical type into the holder (3) and press it down until it engages. Fujitsu... -
Page 53: Closing The Casing
► Slide the casing cover in the direction of the arrow (2) as far as it will go. ► Secure the casing cover with the screws (3). ► Secure the feet (see "Vertical operating position", Page 15 "Horizontal operating position", Page 17). ► Connect all the cables removed before. Fujitsu... -
Page 54: Technical Data
Technical data Technical data Technicaldata FUJITSU Thin Client FUTRO S540 / S740 Electrical data Processor: • S540: Intel Celeron J4005, Gemini Lake Dual Core 2,0 GHz (max. 2,7 GHz Single Core Burst Freq.) with integrated Intel UHD Graphics 600 •... -
Page 55: Ac Adapter
100 - 240 V Max. rated current: 1.85 A Rated frequency: 50 - 60 Hz Only the following adapters with Limited Power Source may be used: S26113-E622-V55 Model ADP-40HH A • • S26113-E623-V55 Model ADP-65JH AB • CP500624-01 Model A12-065N2A A Fujitsu... -
Page 56: Index
20–21 Microphone port 19 Display port 7 Monitor port 7 Disposal 13 Monitor, Connecting 19 switching off 26 Energy saving 13 switching on 23 External devices Ports 19 External devices, Note connecting 20–21 safety 11 Notes important 11 Fujitsu... - Page 57 20 Replacing, USB port, lithium battery 48 connecting devices 21 Replacing, lithium battery 48 USB ports 7 Retransportation 12 USB, ports 6 Safety notes 11 Security Lock 7 Vertical operating position 15 Security Lock device 7 Serial interface 20 Fujitsu...