Miele PDR 514 Operating And Installation Instructions
Commercial tumble dryers
Hide thumbs
Also See for PDR 514:
- Quick start manual (156 pages) ,
- Operating and installation instructions (56 pages) ,
- Operating and installation instructions (38 pages)
Related Manuals for Miele PDR 514
Summary of Contents for Miele PDR 514
- Page 1 Operating and Installation Instructions Commercial Tumble Dryers PDR 514/518/522/528/544 To prevent accidents and machine damage, en-US, CA read these instructions before installation or use. M.-Nr. 11 790 580...
- Page 2 WARNING: FIRE OR EXPLOSION HAZARD Failure to follow safety warnings exactly could result in serious injury, death or property damage. Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. WHAT TO DO IF YOU SMELL GAS Do not try to light any appliance.
-
Page 3: Caring For The Environment
Caring for the environment Disposal of the packaging material The packaging material protects the dryer from transport damage. The packaging materials used are selected from materials which are environmentally friendly for disposal and can therefore be recycled. Recycling the packaging material reduces the use of raw materials in the manufacturing process and also reduces the amount of waste in landfill sites. -
Page 4: Table Of Contents
Contents Caring for the environment .................... IMPORTANT SAFETY INSTRUCTIONS ................. Appropriate use ......................... Preventing misuse ......................Technical safety......................... Dryers with gas heating ....................Correct use........................10 Accessories ........................11 Description of the machine .................... 12 Operating the tumble dryer .................... 13 Machines with residual moisture control (ROP) .............. - Page 5 Contents Transport ........................... 27 Installing the tumble dryer....................27 Securing the machine......................29 Electrical connection ......................29 Supply air, exhaust, and ventilation cross-sections ............30 Supply air/exhaust air ....................30 Calculating the total length and diameter of a supply-air or exhaust pipe ....30 Substitute duct lengths ....................
-
Page 6: Important Safety Instructions
In accordance with standard UL 60335-1, CAN/CSA-C22.2 No. 60335-1, IEC 60335-1, Miele expressly and strongly advises that you read and follow the instructions in the chapter on installing the tumble dryer as well as the IMPORTANT SAFETY INSTRUC- TIONS. -
Page 7: Preventing Misuse
IMPORTANT SAFETY INSTRUCTIONS Preventing misuse Do not make any alterations to the tumble dryer, unless authorized to do so by Miele. Do not lean on the dryer door. Otherwise, the tumble dryer may tip over, causing injury to yourself or others. - Page 8 Unauthorized repairs could result in unforeseen dangers for the user, for which Miele cannot accept liability. Repairs should only be carried out by a Miele authorized technician, otherwise any subsequent damage may not be covered by the warranty. Repair instruc- tions can be requested from Miele.
-
Page 9: Dryers With Gas Heating
Ensure that no closeable door, sliding door, or an oppositely hinged door is installed that would hinder the drum door being opened in any way. If the power cord is damaged, it must be replaced by a Miele authorized technician in order to protect the user from harm. ... -
Page 10: Correct Use
IMPORTANT SAFETY INSTRUCTIONS - Do not smoke. - If there is the smell of gas in a room, never enter the room with an open flame. - Do not carry out any actions that will create electrical sparks (such as pulling out electri- cal plugs or pressing electrical switches or bells). -
Page 11: Accessories
Only use genuine Miele spare parts and accessories with this machine. Using parts or accessories from other manufacturers may invalidate the warranty, and Miele cannot ac- cept liability. Miele cannot be held liable for damage caused by failure to comply with these IM- PORTANT SAFETY INSTRUCTIONS. -
Page 12: Description Of The Machine
Description of the machine ① ⑤ ⑨ ⑥ ⑩ ② ⑦ ③ ⑧ ④ Control panel with Program selector Door Lint filter flap 4 height-adjustable screw feet Electrical connection Communication module slot Intake vents for drying air Exhaust duct Connection for communication box Communication box (optional) For setting up a connection with external systems... -
Page 13: Operating The Tumble Dryer
For starting the selected drying program and canceling a program once it has started. The program selected can be started as soon as the sensor control starts flashing. Optical interface Used for data transfer by Miele Service. Program selector For selecting programs and for switching the machine off. The tumble dryer is switched on when you select a program and switched off by turning the program selector to the position. -
Page 14: Drying Levels
Operating the tumble dryer Drying levels - sensor button = “Normal+” drying level - sensor button = “Normal” drying level - sensor button = “Hand iron” drying level - sensor button = “Machine iron” drying level - sensor button: “Bedding” function - position = “Cottons”... -
Page 15: Indicators
Operating the tumble dryer - sensor button = “Machine iron” drying level - sensor button = “High” temperature setting Temperature set- tings (TOP) - sensor button = “Medium” temperature setting - sensor button = “Low” temperature setting - sensor button = “Cool” temperature setting - sensor button = “High”... -
Page 16: Before Using For The First Time
Complete the initial commissioning process. During the initial com- missioning process, you will need to define the settings for daily use of the tumble dryer. Some settings can only be modified during the initial commissioning process. After that, they can only be changed by Miele Service. -
Page 17: Drying
Drying 1. Notes on correct laundry care Washing before Heavily soiled laundry must be washed particularly thoroughly. Use drying sufficient detergent and select a high wash temperature. If in doubt, wash the items several times. The tumble dryer must not be used for drying items of laundry which have been cleaned using industrial chemicals. -
Page 18: Loading The Tumble Dryer
Drying 2. Loading the tumble dryer Loading the laun- Damage to fabrics caused by incorrect laundry care. Incorrect laundry care can damage fabrics during tumble drying. Before loading, read “1. Notes on correct laundry care”. Open the door. Load the laundry. ... -
Page 19: Drying Level For Programs With A Selectable Drying Level
Drying Drying level for The preset drying level can be changed if required. programs with a Touch the sensor button for the drying level you want. It will then selectable drying light up brightly. level The drying levels that are available for selection depend on the se- lected program. -
Page 20: Starting A Program
Drying Delay Start continues to count down. Turn the program selector to the position. Alternatively, you can Cancelling/deleting Delay Start also cancel Delay Start by opening the door. Delay Start count- - Delay Start times of more than will count down in hours and down then in minutes until the start of the program. -
Page 21: Removing The Laundry
Drying The program is finished when only is visible in the display. If Anti-crease (see “Programmable functions”) has been selected, the drum rotates at intervals. This reduces creasing if the laundry cannot be unloaded straight away. The tumble dryer will switch off automatically after the programmed time after the end of a program. -
Page 22: Changing The Program Sequence
Changing the program sequence Changing a program once it has started You cannot change to another program once a program has started (this prevents unintentional alterations). You will need to cancel the current program before you can select a new one. ... -
Page 23: Time Left
Changing the program sequence Touch the Start/Stop sensor button so that the Delay Start period continues. Time left Altering the program sequence can cause the program duration shown in the display to be adjusted. -
Page 24: Cleaning And Care
Cleaning and care Cleaning the lint filter Risk of fire if the tumble dryer is operated without a lint filter. If there is no lint filter, the air channels, heating elements, and duct- ing can become clogged during drying and may catch fire. The lint filter must not be removed for cleaning. -
Page 25: Additional Annual Cleaning
– clear of lint. Additional annual cleaning Miele Technical Service or a trained specialist must check the interior of the tumble dryer and the ducting for lint deposits once per year and clean the machine if necessary. In the case of electrically-heated tumble dryers, the heater bank and the heating shaft must also be checked by Miele Technical Service Department. -
Page 26: Technical Service
Technical Service Contact in case of fault In the event of a fault which you cannot remedy yourself, please contact your Miele dealer or Miele Technical Service. Contact information for Miele Technical Service can be found at the end of this docu- ment. -
Page 27: Installation
Risk of injury or damage to property due to improper installation. Incorrect installation of the tumble dryer can lead to personal injury or damage to prop- erty. The tumble dryer must only be installed and commissioned by Miele Customer Service or an authorized dealer. ... - Page 28 Installation The floor load created by the tumble dryer is concentrated and transferred to the installa- tion surface via the screw feet. A base is not required. However, an uneven floor surface must be compensated for. (19 11/16") > 300 (24 13/16") (>...
-
Page 29: Securing The Machine
Installation Adjust the tumble dryer screw feet until the machine is level. After the machine has been aligned, screw the washers tightly to the base plate using a screwdriver. Tip: Use a level to ensure correct alignment. Securing the machine The tumble dryer must be secured to the floor by installing the tensioning strips supplied ... -
Page 30: Supply Air, Exhaust, And Ventilation Cross-Sections
If more than one voltage is specified on the data plate, the tumble dryer can be con- verted for connection to the relevant input voltage. This conversion must be performed by Miele Customer Service or by an authorized dealer. During the conversion, the wiring in- structions given on the wiring diagram must be followed. -
Page 31: Substitute Duct Lengths
Installation In upward exhaust ducting systems, a condensate drain must be fitted to the bottom. The condensate must be drained via a water collection tray or a floor drain positioned in an ap- propriate location. If air is being directed from multiple appliances into a combined line (exceptional circum- stances), a non-return device (non-return flap) must be installed in each separate line to prevent backflow. -
Page 32: Maximum Permissible Total Ducting Length
Installation Maximum permissible total ducting length Internal minimum pipe diameter PDR x14 PDR x18 PDR x22 PDR x28 PDR x44 (metal ducting) 5 7/8" (150 mm) 62' 4 1/16" 49' 2 9/16" 39' 4 7/16" 32' 9 11/16" 32' 9 11/16" (19 m) (15 m) (12 m) (10 m) (10 m) 7 1/16"... -
Page 33: Room Ventilation Opening For Air Intake From The Setup Room
Installation Room ventilation opening for air intake from the setup room The minimum dimension of the ventilation opening depends on the cross-section of the vent duct. Vent duct Minimum dimension for ventilation opening 6" (150 mm) 27 7/16"² 82 5/16"² 10 1/4"... -
Page 34: Exhaust Connection
Installation 13/16" (20 mm) >35 7/16" (900 mm) 2 1/16" (52 mm) Exhaust connection 1 7/16" (37 mm) - Page 35 Installation Example 1 Configuring vent ducting made from steel piping for the PDR 914/514 tumble dryers: L1, L2: each 9' 10" (3 m) steel piping B1, B2: each 90° concertina pipe elbow (r = 2d) 90° elbow (r = d) 1. Total duct length Steel pipe L1 = 9' 10" (3.0 m) Steel pipe L2 = 9' 10" (3.0 m) 90°...
- Page 36 Installation Example 2 Common combined exhaust ducting for multiple appliances should only be considered as a solution in exceptional cases. Configuring combined exhaust ducting made from steel for the PDR 914/514 and PDR 918/518 series tumble dryers: L1–L4 each 6' 6" (2 m) steel piping B1–B3 each 90°...
- Page 37 Installation 1. Total pipe length PDR 914/514 Steel pipe L1 = 6' 6" (2.0 m) Steel pipe L2 = 6' 6" (2.0 m) Steel pipe L4 = 6' 6" (2.0 m) 90° concertina pipe elbow B1 = 10' 6" (3.2 m)* (r = 2d) 90° concertina pipe elbow B2 = 10' 6" (3.2 m)* (r = 2d) 90° elbow (r = d) B5 = 6' 3" (1.9 m*) Total duct length 14.3 m * Substitute pipe lengths according to Table 1...
- Page 38 Installation Example 3 Configuring exhaust ducting and a supply pipe made from steel for the PDR 914/514 se- ries tumble dryer: L1, L2: each 6' 6" (2.0 m) steel piping 8' 2" (2.5 m) steel piping B1, B2: 90° concertina pipe elbow for each B3, B4: 90° elbow (r = d) for each 1. Total duct length Steel pipe L1 = 6' 6" (2.0 m)
-
Page 39: Steam Connection (Only For Steam-Heated Variants)
Installation Configuring the room ventilation opening Rooms in which rotary irons and tumble dryers are operated must have an induced ventilation system (e.g., ventilation slots in windows and doors, wall openings with grilles, or opened windows or skylights). For example 1 A duct diameter of 6" (150 mm) was specified in example 1. -
Page 40: Gas
The gas heating is configured at the factory in line with the gas specifications on the sticker on the rear of the machine. If the gas type is changed, a conversion kit must be requested from Miele Service (please specify the machine type, serial number, gas type, gas group, gas connection pressure, and country of installation). - Page 41 Installation If liquid gas-heated machines are being set up below ground level, the operator must pro- vide the system with the necessary aeration and induced ventilation equipment in accor- dance with technical regulations for liquid propane. If no low pressure occurs when a full fire is burning in all fuel-burning installations, this means that the room ventilation is working properly, even if the exhaust gases from the in- stallations are being extracted mechanically.
- Page 42 17.64 lb/h (8.0 kg/h) 11.02 lb/h (5.0 kg/h) Exhaust gas evacuation ducts Gas-heated Miele Tumble Dryers are type B gas fuel-burning installations without flow safeguarding equipment, and with a fan behind the heater. - The mixtures of exhaust gas and air that are emitted by gas-heated tumble dryers must be evacuated through a suitable chimney and out into the atmosphere via the roof.
- Page 43 If the gas family needs to be changed, please request the appropriate conversion kit from Miele Service. When doing so, please specify the product name and the appli- ance number, as well as the gas family, gas group, gas connection pressure, and country where the appliance has been set up.
- Page 44 Connection and conversion instructions Connection and conversion work must be performed by Miele Service or by an autho- rized dealer. The settings for tumble dryers are made at the factory in line with the gas specifications at the rear of the appliance.
- Page 45 Installation Main connection PDR 914/918/922/928/944/514/518/522/528/544 Natural gas Liquid propane Hose Reduction sleeve* Threaded union* * Supplied with the kit for converting natural gas to propane (LP).
- Page 46 Installation Gas regulator valve PDR 914/918/922/928/944/514/518/522/528/544 Connection pressure measuring stub Jet pressure measuring stub Pressure regulator Screw Plug Jet pressure adjustment Make sure that the maximum pressure is set first. Else the minimum pressure would be changed by turning the nut. Loosen the locking bolts of the connection pressure and jet pressure measuring stub.
- Page 47 Installation Burner PDR 914/918/922/514/518/522 = 1 jet; PDR 928/944/528/544 = 2 jets PDR 928/528 PDR 944/544 Burner conversion Replace the jet and the sealing ring (included with the conversion kit). - Natural gas = large hole - Liquid propane = small hole Additional steps necessary to convert to liquid gas are outlined in the “Conversion kit for natural gas to liquid gas conversion”.
-
Page 48: Steam
The steam connection may only be carried out by a certified installer. In addition to these installation instructions, the information from the data plate, wiring diagram, and documentation accompanying the appliance must also be noted and com- plied with when connecting steam-heated Miele appliances. Operating pressure values High-pressure steam version, indirect HP indir. -
Page 49: Fitting Information For Steam And Condensate Hoses
The hot water connection may only be carried out by an authorized or trained/certi- fied technician. In addition to these installation instructions, the information from the data plate, wiring diagram, and documentation accompanying the appliance must also be noted and com- plied with when connecting hot water-heated Miele appliances. -
Page 50: Operating Conditions
Installation Operating conditions Operating pressure Feed water temperature Peak capacity 87 - 145 psi / 600 – 1,000 kPa (6 – 10 bar) 158 – 203°F (70 – 95°C) 1.32 – 6.6 gal/min (0.3 – 1.5 m³/h) For reasons of efficiency, the operating pressures must not fall below the specified values. ... -
Page 51: Networking
Networking Pairing instructions Follow the steps below to connect the tumble dryer to your network. System requirements for WiFi - WiFi 802.11b/g/n - 2.4 GHz band - WPA/WPA2 encryption - DHCP activated - multicastDNS/Bonjour/IGMP snooping activated - Ports 443, 80, 53, and 5353 open - IP DNS server = IP standard gateway/router - Mesh/repeater use: same SSID and password as standard gateway/router - SSID must be permanently visible... - Page 52 Networking - other machines with Bluetooth or WiFi wireless technology...
-
Page 53: Optional Accessories
This module forms the basis for wired communication with Miele MOVE. It is not possible to integrate the machine into the “Miele@home” app for domestic in- stallations. The communication module is intended exclusively for commercial use and is supplied with voltage directly via the Miele Professional machine. -
Page 54: Original Spare Parts And Accessories
Original spare parts and accessories Miele will guarantee to supply functional spare parts for up to 15 years following the dis- continuation of your machine (this does not apply to digital products or products for process documentation). In many cases, genuine Miele spare parts are available for much longer. -
Page 55: Technical Data
Technical data PDR 514 PDR 518 PDR 522 PDR 528 PDR 544 Height 55 1/8" 55 1/8" 55 1/8" 64 9/16" 64 9/16" (1,400 mm) (1,400 mm) (1,400 mm) (1,640 mm) (1,640 mm) Width 35 11/16" 35 11/16" 35 11/16" 47 1/2" 47 1/2" (906 mm) (906 mm) (906 mm) (1,206 mm) (1,206 mm) Depth 33 9/16" 40 3/4" 45 3/4" 40 1/8" 54 1/2" (852 mm) (1,035 mm) (1,162 mm) (1,019 mm) (1,385 mm) Depth with door open 57 5/16"... - Page 56 Miele Professional Technical proservice@mieleusa.com Service | Service Technique Phone | Tél. : 1-888-325-3957 serviceprofessional@miele.ca Manufacturer | Fabricant : Miele & Cie. KG Carl-Miele-Straße 29, 33332 Gütersloh, Germany | Allemagne Alteration rights reserved / Publication date: 35.23 M.-Nr. 11 790 580 / 02...