Page 1
Questo manuale d’istruzione è fornito da trovaprezzi.it. Scopri tutte le offerte per Miele FNS 28463 ED\CS o cerca il tuo prodotto tra le migliori offerte di Frigoriferi e Congelatori Operating and installation instructions Refrigerator To prevent the risk of accidents or damage to the appliance, it is essential to read these instructions before it is installed and used for the first time.
Contents Warning and Safety instructions..............Caring for the environment ................14 Saving energy ....................15 Guide to the appliance ..................17 Ice cube maker with integrated ice cube tray ............. 18 Accessories ....................... 20 Accessories supplied ..................20 Optional accessories................... 20 Before using for the first time ................
Page 3
Contents Explanation of the different settings..............33 Using the minute minder (QuickCool timer) ..........33 Switching the ice cube maker on/off............34 Activating or deactivating the safety lock / ..........36 Switching the appliance off ............... 36 Switching Sabbath mode on/off ..............37 Setting the time before the door alarm ...
Page 4
Contents Service........................ 67 Contact in case of fault ..................67 – Displaying licence agreements..............67 Warranty ......................67 Installation......................68 Installation ......................68 Ventilation ....................... 69 Fitting the supplied wall spacers..............69 Limiting the opening angle of the door ............70 Installation ......................
“Installation”, as well as in the “Warning and Safety instructions”. Miele cannot be held liable for injury or damage caused by non- compliance with these instructions. Keep these instructions in a safe place and pass them on to any future owner.
Page 6
The appliance is also not suitable for use in areas where there is a risk of explosion. Miele cannot be held liable for damage resulting from incorrect or improper use or operation of the appliance. ...
Page 7
– ventilate the room where the appliance is located for several minutes, and – call Miele. The more coolant there is in a refrigeration appliance, the larger the room should be in which it is installed. In the event of a leakage, if the appliance is in a small room, there is a danger of combustible gases building up.
Page 8
If the electrical connection cable supplied is damaged, it must only be replaced by an original spare part to prevent a hazard for the user. Miele can only guarantee the safety of the appliance when original Miele spare parts are used.
Page 9
The ice cube maker must only be connected to a cold water supply. Miele cannot be held liable for damage caused by a faulty water connection. The manufacturer's warranty will be invalidated if the appliance is not repaired by a Miele authorised technician.
Page 10
Warning and Safety instructions To ensure proper air flow in and out of the appliance, the ventilation gaps in the appliance and built-in structure must not be covered or blocked in any way. This would also increase the energy consumption and could cause damage to the appliance.
Page 11
Follow the instructions given on the food manufacturer's packaging regarding storage conditions and use-by dates. Use only genuine original Miele spare parts. If spare parts or accessories from other manufacturers are used, the warranty will be invalidated, and Miele cannot accept liability.
Page 12
Warning and Safety instructions Cleaning and care Throw away the first 3 batches of ice cubes to rinse the ice cube maker and the water pipes. Do this: – before using for the first time – if the ice cube maker has not been used for a long time –...
Page 13
Warning and Safety instructions Transport To avoid damage to the appliance, always transport it upright and in its packaging. Risk of injury and damage! The appliance is very heavy and must be transported by two people. Disposal of your old appliance ...
Please dispose of it at your local community waste collection/recycling centre for electrical and electronic appliances, or contact Miele. You are also responsible for deleting any personal data that may be stored on the appliance being disposed of. Take care not to damage the pipework...
Saving energy Normal energy Increased energy consumption consumption Installation/ In a ventilated room. In an enclosed, unventilated Maintenance room. Protected from direct In direct sunlight. sunlight. Not situated near a heat Situated near a heat source source (radiator, oven). (radiator, oven). Where the ideal ambient Where there is a high room room temperature is approx.
Page 16
Saving energy Normal energy Increased energy consumption consumption Drawers and shelves arranged as they were when the appliance was delivered. Only open the door when Frequent opening of the necessary and for as short a door for long periods will time as possible.
Guide to the appliance a Control panel with display b Interior lighting c NoFrost module d Recessed handle with door opening aid (Click2Open) e Freezer drawers f Ice cube drawer with automatic ice cube maker g Lowest freezer drawer, can also be used as a freezing tray h Ventilation grille For easier installation there are...
Guide to the appliance Ice cube maker with integrated ice cube tray For the automatic ice cube maker to operate, it must be connected to a water supply (see “Water supply”). An ice cube tray is integrated in the ice cube maker where ice cubes are produced.
Page 19
Guide to the appliance Symbols in the display Operation Symbol Meaning Standby Switching the appliance on Settings mode For selecting settings (see “Selecting further settings”) / Minus/plus For altering a setting (e.g. temperature) For confirming a setting / Left/right navigation For scrolling in Settings mode to select a arrow...
Accessories Accessories supplied Optional accessories A range of useful Miele accessories and Cool pack care products is available for your appliance. Accessories are available from Miele directly (see back cover for contact details). Miele all purpose microfibre cloth The cool pack prevents the temperature...
Before using for the first time Before using for the first time Connecting the appliance Connect the appliance to the Removing packaging material electricity supply as described in Remove all packaging material from “Electrical connection”. the inside of the appliance. Removing the protective foil ...
-18 °C. Standby Touch briefly. The welcome message Miele - Willkommen will appear in the display for approx. 3 seconds. If this does not happen and appears in the display, the safety lock is activated (see “Selecting further settings”...
Switching on and off Start screen Switching off the appliance You can switch the appliance off in Settings mode (see “Selecting further settings”). °C °C The start screen is the screen from which all settings can be selected. The display is divided into two fields for Start screen this purpose:...
Switching on and off Switching off for longer periods of time If, during a long absence, the appliance is switched off but not cleaned and the door(s) left shut, there is a risk of mould forming inside the appliance. It is essential to clean the appliance. If the appliance is not going to be used for a longer period of time, observe the following:...
The correct temperature It is very important to set the correct Temperature display temperature for storing food in the appliance. Bacteria will cause food which is not stored at the correct °C temperature to deteriorate rapidly. Temperature influences the growth rate of these microorganisms.
The correct temperature Temperature range Setting the temperature The temperature can be adjusted from Touch the temperature display. -14 °C to -28 °C. The previously set temperature will Useful tip: If you have adjusted the appear. temperature, wait for approx. 6 hours if the appliance is not very full and for ...
Using SuperFreeze Switching SuperFreeze on and off The SuperFreeze function can be switched on. Touch the temperature display. SuperFreeze function For best results, switch on the °C SuperFreeze function before putting fresh food into the freezer. This helps ...
Temperature and door alarm The flashing appliance has been fitted The acoustic and visual signals will be with a warning system which ensures activated if: that the temperature in the freezer – The appliance is switched on and the cannot rise unnoticed and to avoid temperature in the appliance differs energy being wasted if the door is left greatly from the set temperature.
Temperature and door alarm The flashing warmest temperature The door alarm is only displayed on displayed will disappear. The display the start screen. will revert to showing the current The door alarm is automatically temperature in the freezer. supressed when you are in Settings mode.
Changing the time before the Levels 1–7 (level 1 = 30 sec) (level 2 = 1 min) door alarm is triggered Miele@home system settings Further setting options are (only visible if the Wi-Fi stick described in the fitting and has been fitted) installation instructions, which are enclosed with the stick.
Page 31
Selecting further settings Resetting factory settings Accessing information about Display (important when your appliance reporting a fault to Miele Service) Reminder to clean ventilation On (orange symbol)/Off grille Cleaning (only appears when On (symbol orange)/Off...
Page 32
Selecting further settings Selecting further settings In Settings mode , certain settings can be adjusted and functions selected, allowing you to adjust the refrigeration appliance to suit your requirements. See the following pages for more Settings mode information on these settings.
Selecting further settings Entering values Explanation of the different settings All values entered must be confirmed with . If the value is not confirmed, Using the minute minder the display will revert to the start screen (QuickCool timer) after approx. 15 seconds and the selected or altered values will not be The minute minder can be used to time adopted.
Selecting further settings – When the minute minder duration Switching the ice cube maker on/ has elapsed An audible signal will sound and will Danger to health! flash. The first three batches of ice cubes Touch the display. made after the ice cube maker is started up must not be consumed, The start screen appears.
Page 35
Selecting further settings The ice cube maker can be switched off – Switching the ice cube maker off independently of the appliance if you do for a long time not want to make any ice cubes. Risk of damage! Useful tip: If the ice cube maker is If the water supply is shut off while switched off, the ice cube drawer can the ice cube maker is in operation,...
Selecting further settings – Switching off the safety lock Activating or deactivating the safety lock / Touch the display. The safety lock can be activated to appears. secure against unintentional: Touch for approx. 6 seconds. – switching off The start screen appears.
Selecting further settings Switching Sabbath mode on/off – Switching Sabbath mode on Touch . The appliance has a Sabbath mode to support the observance of religious lights up orange. customs. Then lights up white in the display. The following are switched off: –...
Selecting further settings Switching the keypad tone Setting the time before the door / alarm is triggered on/off The appliance has a door alarm. If a Each time a selectable field in the door is open for a longer period of time display is touched, a keypad tone an alarm will sound (unless this has sounds.
Setting the temperature unit °C/°F Useful tip: This data is important for You can choose between degrees reporting an appliance fault to Miele's Celsius °C and degrees Fahrenheit °F customer service department.
(if switched on). Useful tip: The ventilation grille should be cleaned on a regular basis with a brush or vacuum cleaner (e.g. use the dusting brush for Miele vacuum cleaners). A build-up of dust will increase the energy consumption of the appliance.
Freezing and storing food Freezing fresh food Storing frozen food Fresh food should be frozen as quickly Never refreeze partially or fully as possible so that the nutritional value defrosted food. Defrosted food may of the food, its vitamin content, only be refrozen after it has been appearance and flavour are maintained.
Freezing and storing food – Allow hot foods and drinks to cool Home freezing down before placing them in the Only freeze food which is fresh and freezer. Placing hot foods or drinks in in good condition. the freezer causes food that is already frozen to partially thaw and Tips on home freezing increases energy consumption.
Freezing and storing food Before placing food in the appliance – Freezing small amounts of food When freezing more than 1 kg of Place the food in the lower freezer fresh food, switch on the SuperFreeze drawers. function some time before placing the ...
Page 44
Freezing and storing food Storage time for frozen food Defrosting frozen food The storage life of food varies greatly, Never refreeze partially or fully even when a constant temperature of defrosted food. Defrosted food may -18 °C is maintained. Even in frozen only be refrozen after it has been products, degradation processes take cooked.
Freezing and storing food Cooling drinks quickly – Switching the ice cube maker off for a long time When chilling drinks in the freezer, make sure that bottles are not left in Risk of damage! for more than one hour. Otherwise If the water supply is shut off while they could burst, causing injury or the ice cube maker is in operation,...
Freezing and storing food Using the cool pack Using accessories The cool pack prevents the temperature Freezer tray in the freezer from rising too quickly in The lowest freezer drawer in your the event of a power cut. This helps to appliance can be used as a freezer tray.
Freezing and storing food To replace the drawer, push the Adjusting the interior fittings runners back in completely and then Removing freezer drawers on place the drawer on them. telescopic runners Push the drawer into the appliance Some of the freezer drawers are on until it clicks into position.
Automatic defrosting The appliance is equipped with a “NoFrost” system. The freezer defrosts automatically. The moisture generated in the appliance collects on the evaporator and is automatically defrosted and dissipated from time to time. This automatic defrosting system enables the freezer to remain permanently ice-free.
Cleaning and care Cleaning agents Do not let water get into the electronic unit. Cleaning and conditioning agents used inside the appliance must be Steam from a steam cleaning food safe. appliance could reach the electrical components and cause a short To avoid damaging the surfaces of your circuit.
Cleaning and care Insert the ice cube drawer back into Cleaning the ice cube tray the appliance. Clean the ice cube tray: After cleaning, confirm with – before switching off the ice cube You will hear the ice cube tray return to maker for a long period of time.
Cleaning and care Removing the telescopic runners Preparing the appliance for cleaning Switch the appliance off. appears in the display and cooling is switched off. If this is not the case, the safety lock is on (see “Further settings - Switching off the safety lock”).
Cleaning and care Cleaning the interior and Cleaning the front of the accessories appliance and the side panels The appliance should be cleaned If soiling is left on for any length of regularly, or at least twice a year. time, it may become impossible to remove.
Reconnect to the mains and switch cleaned on a regular basis with a the appliance back on. brush or vacuum cleaner (e.g. use the dusting brush for Miele vacuum Switch on the SuperFreeze function cleaners). for a while so that the freezer section can cool down quickly.
With the help of the following guide, minor faults in the performance of the appliance, some of which may result from incorrect operation, can be remedied without contacting Miele. This will save you time and money because you won't need a service call.
Page 55
Problem solving guide Problem Possible cause and remedy The compressor is The ventilation gaps and ventilation grille are covered switching on more or have become too dusty. frequently and for Do not block the ventilation gaps and ventilation longer periods of time. grille.
Page 56
No tools are required to change the door seal. damaged and needs to Change the door seal. A replacement is available be replaced. from Miele. Frost has accumulated This is not a fault. Condensation has settled on the on the front panel of the panel and frozen.
Page 57
Problem solving guide Messages in the display Message Possible cause and remedy lights up in the Demo mode is switched on. display, the appliance Switch Demo mode off (see “Selecting further does not get cold even settings – Switching Demo mode off”). though the controls and the interior lighting are working.
Page 58
Problem solving guide Message Possible cause and remedy lights up red in the The temperature alarm has been triggered (see display and an alarm “Temperature and door alarm - Temperature alarm”). sounds. The temperature in the freezer has risen higher or fallen lower than the temperature set.
Page 59
Problem solving guide Message Possible cause and remedy There is a power cut: The temperature in the lights up red in the appliance over the last few days or hours has risen display and an alarm too high because of a power cut or an interruption to sounds.
Page 60
To switch the alarm off touch via the display. sounds. Call Miele. To report the fault you need the fault code and also the model number and serial number of your appliance. You can access these via the display.
Page 61
There is a kink in the stainless steel hose. Check the stainless steel hose; if it is faulty, it must only be replaced by an original Miele spare part. The water connection pressure is too low. Check that the water connection pressure is between 150 kPa and 600 kPa (1.5 bar and 6 bar).
Page 62
sounds. Call Miele. To report the fault you need the fault code and also the model number and serial number of your appliance. You can access these in the display.
Page 63
Problem solving guide Problems with the ice cube maker Problem Possible cause and remedy You cannot switch the The appliance is not connected to the power supply ice cube maker on. or is not switched on. Reconnect to the mains and switch the appliance back on.
Page 64
This lighting corresponds to risk group RG 2. If the cover is defective, the eyes may be injured. If the lighting cover is defective, do not look from a close range directly into the lighting with optical instruments (e.g. magnifying glass or similar). Call Miele.
Page 65
Problem solving guide Other problems Problem Possible cause and remedy Food has frozen The food packaging was not dry when loaded in the together. freezer. Use a blunt instrument, e.g. a spoon handle or plastic scraper, to prise it apart carefully. There is no audible This is not a fault.
Noises Normal What causes them noises Brrrrr ... A humming noise is made by the motor (compressor). This noise can get louder for brief periods when the motor switches on. Blubb, A gurgling noise can be heard when coolant is circulating blubb ...
2 years. Miele. For more information about country- specific warranty terms and conditions, You can book a Miele customer please contact Miele. service call-out online at www.miele.com/service. Contact information for Miele can be found at the end of this booklet.
*INSTALLATION* Installation Climate range Installation This refrigeration appliance is designed Fire risk and danger of damage for use within specific ambient from appliances which give off heat. temperatures (climate range). Do not Appliances which give off heat can use in ambient temperatures for which it catch fire and set fire to the is not designed.
*INSTALLATION* Installation Ventilation Fitting the supplied wall spacers The wall spacers supplied must be Risk of fire and damage due to used in order to achieve the stated insufficient ventilation! energy consumption values and to If the refrigeration appliance is not prevent the build-up of condensation ventilated sufficiently, the at high ambient temperatures.
*INSTALLATION* Installation Limiting the opening angle of the door The door hinges are set at the factory to enable the door to be opened up to 115°. If the appliance door hits an adjacent wall when opened, for example, the opening angle can be limited to approx.
Page 71
*INSTALLATION* Installation – Fitting the soft-close mechanism Insert the soft-close mechanism on the door hinge side (at an angle initially) until it clicks into position. Then press the other end of the soft- close mechanism into the opening. Undo and remove the screw on ...
Page 72
*INSTALLATION* Installation If you intend to install your appliance side by side with another refrigeration appliance, please ensure that you observe the instructions in “Installation in a side-by-side combination”. The necessary installation parts are supplied with your appliance. Fit the cover on the door hinge. ...
*INSTALLATION* Installation Installation Aligning the appliance Two people are required for installing the appliance. The appliance must be empty to be installed. Move the appliance carefully on floors that are sensitive to scratching To align the appliance, adjust the to prevent damage.
*INSTALLATION* Installation Supporting the appliance door Installing the appliance in existing kitchen units Risk of fire and damage due to insufficient ventilation! If the refrigeration appliance is not ventilated sufficiently, the compressor will run more frequently and for longer periods. This will result in increased energy consumption and a higher operating temperature of the compressor.
Page 75
*INSTALLATION* Installation The larger the ventilation gap, the more economically the compressor will work. – A ventilation gap of at least 50 mm depth must be provided at the back of the appliance behind the whole width of the top box for air to circulate.
*INSTALLATION* Installation Appliance dimensions * Dimensions without wall spacers fitted. Appliance depth is increased by 15 mm with the wall spacers supplied fitted. [mm] [mm] FNS 28463 E ed/cs 1,850 1,815...
*INSTALLATION* Installation All fixings required for side-by-side Installation in a side-by-side installation are supplied with the combination appliance: To avoid a build-up of condensation and resulting damage, refrigerators and freezers should not generally be installed directly next to other such appliances (side by side).
Page 78
*INSTALLATION* Installation The following tools are supplied with Installation the appliance: The backs of the appliances must be kept accessible to complete the installation. The freezer must be installed to the The following additional tools are left of the other refrigeration required: appliance (when viewed from the front).
Page 79
*INSTALLATION* Installation Notes on moving side-by-side Installation steps for the front of the appliance combinations: appliances Push the combination alternately from the left and right corners. Whilst doing so grasp the outside front corners. Do not, under any circumstances, use your knees to ...
Page 80
*INSTALLATION* Installation By fitting the upper connecting bracket both appliances are aligned in height and depth. If one appliance stands higher than the other, start with the higher one first. Place the appliances next to each other so that the fronts are aligned, leaving a gap of slightly over 40 mm between them.
Page 81
*INSTALLATION* Installation Installation steps for the back of the appliances Place the connecting bracket so that the horizontal long slots are on the left hand side and secure them as Place the connecting bracket so follows: that the horizontal long slot is on the left hand side and secure it as 1.
Page 82
*INSTALLATION* Installation The holes for securing the connecting bracket have to be pre-drilled. Place the connecting bracket so that the horizontal long slot is on the left hand side and secure it as follows: 1. Secure it loosely with the screw . 2.
Page 83
*INSTALLATION* Installation Additional installation steps for the front of the appliances Place the trim at the front of the appliance underneath the top connecting bracket and carefully work the trim into the groove. Use Adjust the front feet with the a soft cloth to do this to avoid spanner .
Page 84
*INSTALLATION* Installation Connect the side-by-side combination to the mains as described in the operating and installation instructions of the individual appliance. Appliances with an ice cube maker: Connect the appliance to the mains water supply as described in “Water ...
Page 85
*INSTALLATION* Installation Warning! Risk of damage when moving the appliance combination! The assembled side-by-side combination is very heavy. Incorrect moving can cause dents. Follow the instructions on how to move it. The side-by-side combination must be pushed very carefully into ...
*INSTALLATION* Installation Aligning the appliance door Changing the door hinging The appliance door(s) can be height- The appliance is supplied with left-hand adjusted at the lower hinge plates. hinging. If right-hand hinging is required, the hinges must be changed. Please note that the hinging must not be changed if this appliance is going to be installed side by side with another refrigeration appliance.
Page 87
*INSTALLATION* Installation Preparing to change the door hinging Removing the top covers Open the appliance door. To change the door hinging, you will need the following tools: Place a suitable cover on the floor in front of the appliance to protect the ...
Page 88
*INSTALLATION* Installation Removing the upper soft-close Removing the door mechanism Danger of injury when removing the appliance door! The door is not secure as soon as the pin has been removed from the door hinge. The door must be held by a second person.
Page 89
*INSTALLATION* Installation Changing over the lower hinge plate Secure the hinge plate on the opposite side, starting with screw in the middle at the bottom. Pull the hinge pin complete with Then screw in the other two washer and adjusting foot upwards to screws .
Page 90
*INSTALLATION* Installation Changing over the upper door hinge Slide the cover off to the side. Turn the cover 180° and refit it on the opposite side. Slide on the cover from the side and click it into position. ...
Page 91
*INSTALLATION* Installation Preparing the upper door Useful tip: Place a suitable cover over a stable surface to protect the appliance door from damage. Place the door on it with the outside facing down. Changing over the door opening aid Fully unscrew the screw with the grey plastic collar ...
Page 92
*INSTALLATION* Installation Refit the door opening aid on the Secure the door opening aid using opposite side. the screw with the plastic collar and the screw without plastic The plastic lug on the slider must not collar . Do not overtighten the abut the door seal.
Page 93
*INSTALLATION* Installation Changing over the soft-close mechanism If you want to limit the door opening angle to approx. 90° you need to fit the door opening angle limiter supplied before refitting the soft-close mechanism (see “Installation - Fitting the door opening angle limiter”). ...
Page 94
*INSTALLATION* Installation Refitting the door Use your fingers to insert the pin into the door bearing bush. Screw in the pin (by approx. ¼ turn) until it clicks into position. Fit the safety cover onto the pin. Place the door onto the hinge pin The appliance door is not secure until from above and guide the upper the safety cover ...
Page 95
*INSTALLATION* Installation Securing the soft-close mechanism Fitting the upper covers Open the door 90°. Fit the cover on the door hinge. Fit the panel so that it clicks into position. Slide on the cover until it clicks into position.
*INSTALLATION* Installation Aligning the appliance doors The appliance door can be aligned with the appliance housing after it has been fitted. In the following illustration the door is not shown in the closed position to make it easier to see what you have to To align the appliance door, use the outer slots in the lower hinge plate: ...
The stainless steel hose must only the refrigeration appliance is being be replaced by an original Miele used. spare part. A stainless steel hose Connect the refrigeration appliance which is suitable for use with to the drinking water supply.
*INSTALLATION* Installation Water supply – Connecting the stainless steel hose to the refrigeration appliance Ensure that all connections are watertight. Risk of damage to the stainless steel hose. The water supply from the tap to the ice cube maker may become interrupted.
Page 99
*INSTALLATION* Installation Tighten the nut with the tool supplied by turning it clockwise until the maximum torque is reached and the tool is over-torqued. – Connecting the stainless steel hose to the tap Unscrew the safety cap from the nut ...
*INSTALLATION* Installation The socket must not be concealed Electrical connection behind the appliance and must be The appliance must only be connected easily accessible so that the appliance using the connection cable supplied can be quickly disconnected from the (AC 220–240 V, 50 Hz supply). electricity supply in case of an emergency.
Page 101
*INSTALLATION* Installation Do not connect the refrigeration Connecting the appliance appliance to a stand-alone inverter such as those used with an autonomous energy source, e.g. solar power. When the refrigeration appliance is switched on, power surges could result in a safety switch-off. This could damage the electronics.
Page 103
Wellington 6011 43rd Floor Unit 4301-4303 689 Sukhumvit Road 0800 464 353 (0800 4 MIELE) North Klongton Sub-District www.miele.co.nz Vadhana District Bangkok 10110, Thailand Miele Global Headquarters Germany Miele & Cie. KG, Carl-Miele-Straße 29, 33332 Gütersloh, Federal Republic of Germany...