Advertisement
Quick Links
Advertisement
Related Manuals for Beko 01M-8850803200-2721-03
Summary of Contents for Beko 01M-8850803200-2721-03
- Page 1 Cooker Hood User Manual HCB93042X 01M-8850803200-2721-03...
- Page 2 Please read this manual first! Dear Customers! Thank you for preferring a Beko product. We hope that you get the best results from your product which has been manufactured with high quality and state-of-the-art technology. Therefore, please read this entire user manual and all other accompanying documents carefully before using the product and keep it as a reference for future use.
-
Page 3: Table Of Contents
CONTENTS 1 Important safety and 1.1 General safety ......4 ......4 1.1.2 Product safety. -
Page 4: Important Safety And
Important safety and environmental instructions This section contains safety in- If the power cable is faulty, it structions that will help protect should be replaced by a qualified from risk of personal injury or prop- person certified by the manufac- erty damage. -
Page 5: Product Safety
Important safety and environmental instructions 1.1.2 Product safety Therefore, be careful about cloths and curtains. You can use a pipe with a diameter Never leave the cooker unat- of 120 mm or 150 mm on the flue tended when frying foods; other- connection of the hood. -
Page 6: Intended Use
Important safety and environmental instructions Simultaneous and smooth op- This appliance can be used by the eration of the hood and another children who are at the age of 8 or device that require air is only pos- over and by the people who have sible when a low pressure of 4 Pa limited physical, sensory or men- (0.04 mbar) is reached, and thus... - Page 7 Important safety and environmental instructions 1.3 Compliance with WEEE Directive and disposing of the waste product This product complies with EU WEEE Directive (2012/19/EU). This product bears a classification symbol for waste electrical and electronic equipment (WEEE). This product has been manufactured with high quality parts and materials which can be reused and are suitable for recycling.
-
Page 8: Controls And Parts
Technical specifıcations of your appliance 2.1 Controls and parts 1. Chimney Mounting Bracket 2. Upper Chimney Cover 3. Lower Chimney Cover 4. Motor Housing 5. Baffle Filters 6. Safety wire 2.2 Technical data Power con- 220-240V ~50Hz sumption Absorption 400 W Markings on the product or the values stated in other documents supplied with the product are values obtained under laboratory conditions as per relevant standards. - Page 9 Installing your appliance 3.1 Wall drilling and bracket fixing 3.1.1 Wall mounting Mark the center of the bracket holes and drill ø Draw a vertical line on the at the center of the 8 mm holes. Insert wall plug in the wall. Secure wall.
- Page 10 Installing your appliance 3.3.2 Recirculation mode air outlet Insert the connection extension pieces laterally in air outlet connection. Make sure that the outlet of the extension pieces is horizontally and vertically aligned with the chimney outlets. Ensure that the activated charcoal filters have been inserted.
- Page 11 Installing your appliance 3.4 Chimney assembly In this mode, only the aluminum filters are in- stalled. Recirculation mode In the recirculation mode, air is drawn into the hood, fats are trapped by the filters, the air then passes through charcoal filters to remove cooking odors, the purified air is then passed back into the kitchen.
- Page 12 Operating your appliance The hood is equipped with electronic touch con- After activated the long period delay timer func- trol that is located on the front edge of the range o i t i l e l l i l l i hood canopy.
-
Page 13: Surfaces
Cleaning and maintenance 5.1 Surfaces Wash with warm soapy water and a soft sponge. Never use abrasive detergent, scouring pads, steel wool or solvents on any part of this appliance as this will cause irreparable damage. Dry the kitchen hood using a cloth that does not produce fluff. 5.2 Aluminium filters Wash in the dishwasher, it is advisable to stack them vertically to avoid food residue sticking to... - Page 14 Troubleshooting Symptoms Possible Cause Action Motor does not working No electrical supply Ensure the plug is connected properly. Reset circuit breaker. Poor airflow Aluminum filters clogged Clean the filters and replace when dry Charcoal filters clogged Replace charcoal the new filters charcoal with new filterssets Motor running but no airflow Butterfly valve jammed...