Sony ICF-DVD57TV Service Manual page 64

ICF-DVD57TV
MAIN BOARD IC401 µPD789478GC-SR7596A (MAIN SYSTEM CONTROLLER)
Pin No. Pin Name
1, 2
NC
3 to 5
VLC2 to VLC0
6 to 9 COM0 to COM3
10 to 25 SEG0 to SEG15
26 to 28
NC
µ-COM R DATA
29
30
OPEN/CLOSE LED
31
AUX LED
32
TV LED
µ-COM S DATA
33
µ-COM CLOCK
34
35
TUNER LED
36
XRESET
µ-COM LATCH
37
38 AVDD
39
DVD OPEN
ENCODE+,
40, 41
ENCODE-
42
DVD CLOSE
43 to 46 KEY3 to KEY0
47 AVSS
48
RC
49
AC IN
50
DVDXIFBUSY
51 LOADING A
52
BUZZER
53
DVD SI0
54
DVD SO0
55 DVD SCK
56
DVD XIFCS
57
DVD AMUT IN
58
DVD RST
59 DVD LED
60 LOADING B
61
TRAY DET
62 MONITOR ON
63
RADIO MUTE
64 RADIO CE
65
RADIO DATA
66
RADIO CLK
67 VOL CLK
68 VOL DAT
69
IC0
70
XT1
71
XT2
64
All manuals and user guides at all-guides.com
I/O
- Not used
- Terminal for doubler circuit capacitor connection to develop liquid crystal display drive voltage
O
Common drive signal output to the liquid crystal display
O
Segment drive signal output to the liquid crystal display
- Not used
I Serial data input from the sub system controller
O LED drive signal output of the OPEN/CLOSE indicator "H": LED on
O LED drive signal output of the AUX indicator "H": LED on
O LED drive signal output of the TV indicator "H": LED on
O
Serial data output to the sub system controller
O Serial data transfer clock signal output to the sub system controller
O LED drive signal output of the RADIO ON/BAND indicator "H": LED on
O
System reset signal output to the sub system controller
O
Latch signal output to the sub system controller
- Power supply terminal (+3.3V) (for A/D converter)
I Disc tray open detect switch input terminal "H": disc tray is opend
I
Jog dial pulse input from the rotary encoder
I Disc tray close detect switch input terminal "L": disc tray is closed
I Front panel key input terminal (A/D input)
- Ground terminal (for A/D converter)
I SIRCS signal input from the remote control receiver
I Power failure detection signal input terminal
O Busy signal output to the servo DSP
O Disc tray open/close motor drive signal (close direction) output terminal
I Beep sound drive signal output terminal
I Serial data input from the servo DSP
O Serial data output to the servo DSP
I Serial data transfer clock signal input from the servo DSP
I Chip select signal input from the servo DSP
I Audio muting on/off control signal input from the servo DSP
O Reset signal output to the servo DSP
O LED drive signal output of the DVD indicator "H": LED on
O Disc tray open/close motor drive signal (open direction) output terminal
O Disc tray open/close detection signal output to the servo DSP "L": disc tray is closed
O
Power on/off control signal output for the monitor section "H": power on
O Radio muting on/off control signal output to the FM/AM PLL "L": muting on
O PLL chip enable signal output to the FM/AM PLL
O PLL serial data output to the FM/AM PLL
O PLL serial data transfer clock signal output to the FM/AM PLL
O
Serial data transfer clock signal output to the electrical volume
O Serial data output to the electrical volume
- Not used
I Sub system clock input terminal (32.768 kHz)
O Sub system clock output terminal (32.768 kHz)
Description