Especially critical components as indicated on the circuit path to the chassis will indicate an open circuit. diagram should not be replaced by other manufacture's. Furthermore where a short circuit has occurred, replace those components that indicate evidence of overheating. PRO-730HD...
Page 3
1.2 PRODUCT SAFETY NOTICE ANY MEASUREMENTS NOT WITHIN THE LIMITS OUTLINED ABOVE ARE INDICATIVE OF A POTENTIAL Many electrical and mechanical parts in PIONEER set have special SHOCK HAZARD AND MUST BE CORRECTED BEFORE safety related characteristics. These are often not evident from RETURNING THE SET TO THE CUSTOMER.
Page 4
Each Lens Assy POWER SW Assy HV Distributor Focus VR (VR1) POWER SUPPLY Assy CRT Service Assy R, G, B AC Power Cord DEFLECTION SERVICE Assy Fig.1 Carged Section and High Voltage Generation Point Fig.2 Component parts for X-ray protection PRO-730HD...
Page 5
By following the instructions in this manual, be sure to apply the prescribed grease or glue to proper portions by the appropriate amount.For replacement parts or tools, the prescribed ones should be used. PRO-730HD...
4.7 R CRT DRIVE ASSY..........................114 4.8 G CRT DRIVE ASSY ..........................116 4.9 B CRT DRIVE ASSY..........................118 4.10 DEFLECTION SERVICE ASSY ......................120 4.11 DIGITAL CONV.ASSY .......................... 126 4.12 POWER SUPPLY and POWER SW ASSYS..................128 5. PCB PARTS LIST ............................134 PRO-730HD...
More than 1250 lines (PRO-630HD) External dimensions More than 1150 lines (PRO-530HD) PRO-730HD .... 1510 (W) x 1425 (H) x 709 (D) mm [Input digital test pattern (1400 lines resolution)] 59-7/16 (W) x 56-1/8 (H) x 27-15/16 (D) inch PRO-630HD .... 1378 (W) x 1351 (H) x 675 (D) mm Input terminals ..........4 video inputs...
Assy L Frame Cover V Assy R Frame Cover H How to remove Frame Cover Frame Cover V Assy L Frame Cover V Assy R Cloth 5 (PRO-730HD Only) Flat-blade Screw Driver Cloth Frame Cover H Frame Cover H PRO-730HD...
Page 9
See Contrast table (2) Screw ABA1226 Frame Cover V Assy L See Contrast table (2) (2) CONTRAST TABLE PRO-730HD/KUXC/CA, PRO-630HD/KUXC/CA and PRO-530HD/KUXC/CA are constructed the same except for the following : PRO-730HD/ PRO-630HD/ PRO-530HD/ Mark No. Symbol and Description KUXC/CA...
2.2 FRONT SECTION (1) Refer to "2.6 CRT SECTION". ×4 ×4 PRO-730HD...
Page 11
1P Lead Wire (J6) ADX2662 1P Lead Wire (J7) ADX2663 1P Lead Wire (J8) ADX2664 (2) CONTRAST TABLE PRO-730HD/KUXC/CA, PRO-630HD/KUXC/CA and PRO-530HD/KUXC/CA are constructed the same except for the following : PRO-730HD/ PRO-630HD/ PRO-530HD/ Mark No. Symbol and Description KUXC/CA...
2.3 FRONT SECTION (2) Rear View 22 30 • How to check the serial number: Remove the grille and look at the front panel from below. (PRO-730HD Only) (PRO-730HD Only) (PRO-730HD Only) 29 282928 27 27 29 28 29 28...
Page 13
See Contrast table (2) Catcher F2M AEC1609 Side Panel Assy R See Contrast table (2) (2) CONTRAST TABLE PRO-730HD/KUXC/CA, PRO-630HD/KUXC/CA and PRO-530HD/KUXC/CA are constructed the same except for the following : PRO-730HD/ PRO-630HD/ PRO-530HD/ Mark No. Symbol and Description KUXC/CA...
Be sure to remove the mirror inside the cabinet before removing the mirror case. If the mirror case is removed first, the mirror will fall and likely become damaged. A Torx driver is required to remove the No.11 screws. Rear View PRO-730HD...
Page 15
NSP 6 Mirror Upper Stay L ANG2004 NSP 7 Mirror Upper Stay R ANG2005 (2) CONTRAST TABLE PRO-730HD/KUXC/CA, PRO-630HD/KUXC/CA and PRO-530HD/KUXC/CA are constructed the same except for the following : PRO-730HD/ PRO-630HD/ PRO-530HD/ Mark No. Symbol and Description KUXC/CA KUXC/CA...
2.5 SCREEN SECTION When attaching the screen holder to the cabinet, make the left side basically level. 1/10 Cabinet inch Screen Frame Assy Top View Front View Rear View 17 17 17 17 17 17 PRO-730HD...
Page 17
See Contrast table (2) Panel Frame H See Contrast table (2) Panel Frame V See Contrast table (2) (2) CONTRAST TABLE PRO-730HD/KUXC/CA, PRO-630HD/KUXC/CA and PRO-530HD/KUXC/CA are constructed the same except for the following : PRO-730HD/ PRO-630HD/ PRO-530HD/ Mark No. Symbol and Description...
2.6 CRT SECTION Blue Green PRO-530HD Only Front Side To Cabinet 26 26 CRT Stand (Accessory of Cabinet) Rear Side PRO-730HD...
Page 19
VM Coil (L6) ATL1146 Lens Assy See Contrast table (2) Lens Assy See Contrast table (2) (2) CONTRAST TABLE PRO-730HD/KUXC/CA, PRO-630HD/KUXC/CA and PRO-530HD/KUXC/CA are constructed the same except for the following : PRO-730HD/ PRO-630HD/ PRO-530HD/ Mark No. Symbol and Description KUXC/CA...
2.7 REAR SECTION Refer to "2.9 CHASSIS SECTION". Refer to "2.8 DVI SECTION". PRO-730HD...
Page 21
Screw ABA1286 NSP 9 Back Cover Panel See Contrast table (2) Screw ABA1241 (2) CONTRAST TABLE PRO-730HD/KUXC/CA, PRO-630HD/KUXC/CA and PRO-530HD/KUXC/CA are constructed the same except for the following : PRO-730HD/ PRO-630HD/ PRO-530HD/ Mark No. Symbol and Description KUXC/CA KUXC/CA KUXC/CA...
Page 23
Part No. DVI SERVICE Assy AWV1983 Power Switch (S2) ASG1090 Wire Harness B (J14) ADX2810 NSP 4 DVI Chassis ANA1708 NSP 5 DVI Bonnet ANE1606 NSP 6 Lead Clamper M AEC1611 Screw ABZ30P100FZK Screw BPZ30P100FZK Hexagonal Head Screw BBA1051 PRO-730HD...
2.10 REAR PANEL SECTION Caution for the RF Switch installation No Good TUNER TUNER Assy Assy Switch Rear Switch side Top View 13, 9 PRO-730HD...
Page 27
Cable Clip D3S AEC1782 NSP 7 ID Label See Contrast table (2) Rear Panel ANC2350 (2) CONTRAST TABLE PRO-730HD/KUXC/CA, PRO-630HD/KUXC/CA and PRO-530HD/KUXC/CA are constructed the same except for the following : PRO-730HD/ PRO-630HD/ PRO-530HD/ Mark No. Symbol and Description KUXC/CA KUXC/CA...
COMPONENT MAIN U-COM BLOCK BLOCK SCL1 SDA1 IC3901 MDET ESCL CXA2171Q ESDA SCL2 CMUTE SDA2 AUTO CONVERGENCE SCL3 MOFF IC3906 SDA3 AUTO WHITE BALANCE COMPONENT DVIRST CXA2171Q SCL1 BLOCK SDA1 IC6016 CXA1875AM DVI BLOCK SIGNAL ASSY DVI SERVICE ASSY PRO-730HD...
INPUT 2 INPUTF L,R MONITOR/TV INPUT 3 INPUT5,6 INPUT F DVI L,R INPUT 5 AUDIO INPUT 6 VAR/FIX VAR/FIX MUTE FIX L,R VAR/FIX MUTE AUDIO OUT VAR L,R IC2203 MC14066BF CENTER IN MONITOR MUTE MONITOR/ TV OUT MON/TV MUTE PRO-730HD...
Page 33
L,R/CENTER IC5502 PRE AMP IC2202 BH3865S MC14066BF TONE FRONT VOL.CONTROL CONTROL SURROUND AUDIO MUTE BASS BOOST CENTER IC5501 SCL2 AMUTE2 NJM4558MD SDA2 IC5503 DETECTION IC5504 NJM4558MD AUDIO PHASE TRAP MUTE SECURITY IC1101 LA4282 SPEAKER AMUTE POWER AMP CMUTE AMUTE2 PRO-730HD...
V DEF Block Block IC801 IC802 M5220P LA78045 T601 PRE AMP V AMP VOUT ANODE VDRV ± HIGH HOUT VOLTAGE FOCUS OUTPUT Q512,Q513 Q511 H. DEF H. DEF H.V. CPURST HDRV DRIVE CONTROL H. DEF HPIN CONTROL HVRST Q510,Q508 IC502 NJM4558DXP PRO-730HD...
Page 42
Name Name Name V+13 14.5 V+13 V+12VA 12.0 V+12VA V+5V V+5V RGB R 0.01 DSUB R RGB G 0.01 DSUB G RGB B 0.01 DSUB B 0.01 VIDEO RGB H 0.01 DSUB H 0.01 RGB V 0.01 DSUB V PRO-730HD...
3.4 TUNER ASSY TUNER ASSY (AWZ6712) RF SWITCH TV FRONT END SYSTEM UNIT (MAIN) (TV1) TV FRONT END SYSTEM UNIT (SUB) TUNER 1 BLOCK (TV2) TUNER 2 BLOCK PRO-730HD...
Page 45
(TV1) (TV1) CN5302 - pins 3, 25 (TVL) V: 1V/div. H: 500µsec/div. (Input : TUNER, 1kHz, 100% mod. Vol. MAX) (TV1) (TV1) (TV1) (TV2) (TV2) (TV2) (TV1) (TV2) CN2207 : The power supply is shown with the marked box. PRO-730HD...
3.5 SIGNAL ASSY (1/5) CN5302 SIGNAL ASSY (AWZ6716) • AV I/O BLOCK (TV2) (TV2) (TV1) (TV1) (TV1) (SUB) AV SW CN6004 PRO-730HD...
Page 47
: VIDEO SIGNAL ROUTE (SUB) (TV1) : VIDEO SIGNAL ROUTE (TV1) (TV2) : VIDEO SIGNAL ROUTE (TV2) : Y SIGNAL ROUTE : C SIGNAL ROUTE : AUDIO SIGNAL ROUTE (TV1) : AUDIO SIGNAL ROUTE (TV1) (SUB) (SUB) (SUB) (SUB) CN5501 V8 PRO-730HD...
Page 48
Voltage (V) Voltage (V) Voltage (V) 4.5/4.8 4.5/4.8 4.5/4.8 4.5/4.8 0/12 0/12 0/12 0/12 0/12 0/12 0/12 0/12 SIGNAL ASSY IC3901 (CXA2171Q) IC3906 (CXA2171Q) IC3907 (M52055FP) Voltage (V) Voltage (V) Voltage (V) Voltage (V) Voltage (V) Voltage (V) Voltage (V) PRO-730HD...
Page 49
100/0/75/0 Full Field color-bar) CN3905 - pin 17 (MV) IC3906 - pin 23 (SV) V: 1V/div. H: 2msec/div. V: 1V/div. H: 2msec/div. (Input : INPUT1 (COMPONENT), 1080I (Input : INPUT1 (COMPONENT), 1080I 100/0/75/0 Full Field color-bar) 100/0/75/0 Full Field color-bar) PRO-730HD...
: PB SIGNAL ROUTE (RGB) (PR) : PR SIGNAL ROUTE : R, G or B SIGNAL ROUTE (PB SUB) : PB SIGNAL (SUB) : Y SIGNAL ROUTE (PR SUB) : PR SIGNAL (SUB) (SUB) : Y SIGNAL ROUTE (SUB) PRO-730HD...
3.9 SIGNAL (5/5),BNC,FRONT CONTROL,LED RLS and REMOTE SENSOR ASSYS (PB) : VIDEO SIGNAL ROUTE : PB SIGNAL ROUTE (PR) : PR SIGNAL ROUTE : Y SIGNAL ROUTE BNC ASSY (AWZ6720) (PB) (PR) SIGNAL ASSY (AWZ6716) • SR BLOCK RS-232C DRIVER JA1801 JA1802 PRO-730HD...
Page 57
FRONT CONTROL ASSY (AWZ6718) LED RLS ASSY (AWZ6719) REMOTE SENSOR ASSY (AWZ6717) D E F PRO-730HD...
Page 63
VIDEO UCOM SERVICE ASSY IC1904 IC1907 (TC74VHCT541AFT) (TC74VHCT541AFT) IC1906 (PD5815A8) IC1905 (M62399FP) Voltage (V) Voltage (V) Voltage (V) Voltage (V) Voltage (V) 0/3.0 0/3.3 0/3.0 1.3/1.7 0/3.3 0/3.3 0/3.3 0/3.3 PRO-730HD...
Page 67
: C SIGNAL ROUTE UNIT (AXY1061) (PB SUB) (480p/1080i) : PB SIGNAL (SUB) : Y SIGNAL ROUTE (1080i or 480p) (PR SUB) : PR SIGNAL (SUB) (SUB) : Y SIGNAL ROUTE (SUB) (PB) (SUB) (PR) : C SIGNAL ROUTE (SUB) PRO-730HD...
Page 73
Voltage (V) 12.0 0.6/5.6 12.0 1.3/5 IC4613 (TC7SB66FU) IC4602 IC4603 (TC7W53FU) IC4609 (AD8057ART) Voltage (V) (TC74HC4053AF) Voltage (V) Voltage (V) Voltage (V) 0.7/5.7 12.0 IC4614 (TC7SB66FU) Voltage (V) IC4612 (TC7SB66FU) Voltage (V) IC4604 (BA7655AF) Voltage (V) IC4615 (TC7SET08FU) Voltage (V) PRO-730HD...
3.15 VIDEO UCOM ASSY ( 4/5) CN3905 RGB SW (R) (G) (B) (PB) (PR) (480p/1080i) MATRIX COLOR CONTROL RGB PREAMP PRO-730HD...
Page 75
VIDEO UCOM SERVICE ASSY (AWV1992) • VIDEO BLOCK : Y SIGNAL ROUTE (RGB) : R, G or B SIGNAL ROUTE (PB) : PB SIGNAL ROUTE (PR) : PR SIGNAL ROUTE OSD SW CN5151 CN5101 CN5201 PRO-730HD...
3.16 VIDEO UCOM ASSY (5/5) VIDEO UCOM SERVICE ASSY (AWV1992) • AUDIO PRE BLOCK PREAMP BLOCK AUDIO PREAMP TRAP BLOCK PRO-730HD...
Page 77
: AUDIO SIGNAL ROUTE IC5502 (BH3865S) IC5501 (NJM4558MD) Voltage (V) Voltage (V) Voltage (V) IC5503 (NJM4558MD) Voltage (V) IC5504 (NJM4558MD) Voltage (V) PRO-730HD...
3.17 R, G and B CRT DRIVE ASSYS R CRT DRIVE ASSY (AWZ6709) R CRT FOCUS VR CRT STAND R VM COIL G CRT DRIVE ASSY ASSY (AWZ6710) G CRT FOCUS VR CRT STAND G VM COIL PRO-730HD...
3.19 DEFLECTION SERVICE ASSY (2/2) : CHARGED SECTION CN202 PRO-730HD...
Page 85
DEFLECTION SERVICE ASSY (AWV1967) • POWER SUPPLY BLOCK S5688G-T S5688G-T CN5102 • NOTE FOR FUSE REPLACEMENT FOR CONTINUED PROTECTION AGAINST RISK OF FIRE. CAUTION - REPLACE WITH SAME TYPE AND RATINGS ONLY. PRO-730HD...
3.21 POWER SUPPLY ASSY (1/3) POWER SUPPLY ASSY (AWV1960) • POWER SUPPLY BLOCK TO REAR PANEL AC IN J901 POWER SW ASSY (AWZ6713) : CHARGED SECTION PRO-730HD...
Page 91
CN6001 • NOTE FOR FUSE REPLACEMENT FOR CONTINUED PROTECTION AGAINST RISK OF FIRE. CAUTION - REPLACE WITH SAME TYPE AND RATINGS ONLY. PRO-730HD...
Transistor B C E SIDE A Transistor with resistor B C E Field effect SIDE B Chip Part P.C.Board transistor Resistor array 3-terminal regulator For DEFLECTION SERVICE and POWER SUPPLY ASSYS Guide page Large size SCH diagram Detailed page PRO-730HD...
4.1 FRONT INPUT and D-SUB ASSYS SIDE A SIDE A CN2204 FRONT INPUT ASSY CN5252 Q5251 Q5252 (ANP2016-B) CN3903 D-SUB ASSY J5271 IC5271 (ANP2016-B) PRO-730HD...
SIDE A CN3901 BNC ASSY J5041 (ANP2018-B) CN1904 FRONT CONTROL ASSY CN5001 (ANP2018-B) J5001 LED RLS ASSY REMOTE SENSOR ASSY J5002 J5002 (ANP2018-B) (ANP2018-B) CN5030 VR5001 PC5001 Q5003 Q5002 Q5001 CN1802 C D E F C D E F PRO-730HD...
Page 107
SIDE B SIDE B BNC ASSY J5041 (ANP2018-B) FRONT CONTROL ASSY CN5001 J5001 (ANP2018-B) LED RLS ASSY REMOTE SENSOR ASSY J5002 J5002 (ANP2018-B) (ANP2018-B) CN5030 C D E F C D E F PRO-730HD...
4.9 B CRT DRIVE ASSY SIDE A SIDE A B CRT DRIVE ASSY CN4601 Pins 1 - 5 IC5201 VR5201 Q5201 FOCUS VR CRT STAND (ANP2016-B) CN5207 CN5206 J5203 BLUE CN751 J5203 SVM COIL Pins 7 - 9 PRO-730HD...
Page 119
SIDE B SIDE B B CRT DRIVE ASSY CN5201 (ANP2016-B) J5203 CN5206 CN5207 mark shows a high voltage generation point. PRO-730HD...
4.11 DIGITAL CONV.ASSY SIDE A SIDE A DIGITAL CONV. ASSY IC1201 IC1203 Q1203 CN406 IC1204 Q1204 Q1206 Q1205 Q1202 IC1205 IC1202 IC1207 IC1206 CN405 IC1209 IC1210 IC1211 IC1208 (ANP2020-A) PRO-730HD...
Page 127
SIDE B SIDE B DIGITAL CONV. ASSY Q1201 (ANP2020-A) PRO-730HD...
Page 148
PIONEER CORPORATION 4-1, Meguro 1-chome, Meguro-ku, Tokyo 153-8654, Japan PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A. PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936 PIONEER CORPORATION 2002 T-ZZY OCT.
Page 149
By following the instructions in this manual, be sure to apply the prescribed grease or glue to proper portions by the appropriate amount.For replacement parts or tools, the prescribed ones should be used. PRO-730HD...
Page 150
6.5 FACTORY ADJ MODE..........................154 6.6 ADJUSTMENT............................156 7. GENERAL INFORMATION ...........................174 7.1 DIAGNOSIS............................174 7.1.1 DIAGNOSIS METHOD........................174 7.1.2 DISASSEMBLY ..........................178 7.1.3 WIRING DIAGRAM ..........................182 7.1.4 ABOUT THE SERVICE (RS-232C) PORT ..................184 7.2 IC ................................185 7.3 EXPLANATION ............................237 8. PANEL FACILITIES ............................250 PRO-730HD...
Check the status of the unit after replacement of the EEPROMs, and readjust if necessary. 6.2 JIGS AND MEASURING INSTRUMENTS Remote control unit Color bar generator Adjustment screwdriver Screwdriver AXD1468 D. DC Voltmeter DVD / LD Player Dual-trace oscilloscope Monoscope For HD Signal generator Soldering iron PRO-730HD...
• The necessary adjustment items differ, depending on the assembly or optical part replaced. Check and readjust the adjustment items corresponding to the replaced assembly or part, following adjustment procedures 1 to 8. Example: When the DIGITAL CONV. Assy is replaced, perform the following: 3. Focus check/adjustment → 4. Screen size check/adjustment → 5. Convergence check/adjustment PRO-730HD...
• During power-saving mode operation (power management) Flashing: Repeat 2s on and 2s off. About power management: When input signal disappears only at the time of INPUT5 and 6, it becomes the power-saving mode. (Refer to page 248.) PRO-730HD...
Page 155
Telop : White (MUTING) (MUTING) (SPLIT) (SPLIT) PICTURE OFFSET SIGNAL ADJ mode PureCinema mode mode Telop : White Telop : White Telop : White (MUTING) (MUTING) (MUTING) COLOR TEMP CONVER ADJ mode OFFSET mode Telop : White Telop : White PRO-730HD...
4. 2 – 2 COMPONENT ADJ 5. IP SETTING 5. 2 – 2 S–VIDEO ADJ 6. FREQ JUDGMENT ADJ 6. 2 – 2 COMPOSITE ADJ Do not perform the adjustment for service. Do not perform the adjustment for service. PRO-730HD...
Page 157
TP-BK of the CRT DRIVE assembly. If the levels are within 180 V ±5 V, the adjustment is not necessary. Input the noted data. If the levels are not within the above level, proceed with the above adjustment. PRO-730HD...
Page 158
Cross hatch • Apply an adhesive between the neck part of CRT and centering magnet so that the centering magnet of the deflection yoke does not move. Deflection yoke Centering magnet (Turn in either direction until cross signal becomes white.) PRO-730HD...
Page 159
• the green halo disappears, and the blue halo begins to appear. Note on tightening the thumbscrew after adjustment : Observe the crosshatch signals on the screen while tightening the thumbscrew, to check that the lens does not rotate with the thumbscrew. PRO-730HD...
Page 160
Vertical Size Adjustment Note : Screen mode : FULL 1st FAC Start ADJUST V SIZE INPUT 1:Monoscope 91% ± 2% Green screen INPUT TV Adjust the size so that the picture is completely General displayed on the screen. broadcasting PRO-730HD...
Page 161
H PHASE is set in factory shipment by the most suitable value. But, there is the case that screen is missed as an upper figure occurs by the signal format of other apparatus to be connected to. A screen can be improved as the following by the readjustment. However, attention is necessory because in convenience may occur when connected to another apparatus. PRO-730HD...
Page 162
SERVICE ASSY DIGITAL CONV. ASSY The data stored in the EEPROMs are as follows: IC1903 IC1203 24LC32A(I)P OFFSET CONVER. MODE 1 (DFH, DFV) IC1906 OFFSET CONVER. MODE 3 PD5815 Factory-preset values for convergence User-adjusted values for convergence (CENTER, MULTI-POINT) PRO-730HD...
Page 163
Cyclically changes with the CH+ or CH- key as follows: The above offset convergence values are common to the PRO-530HD, PRO-630HD and PRO-730HD. If the offset convergence values are as indicated in Table 2, proceed to 3.3. If the values are not the same, adjust the values with the numeric keys and VOL +/–...
Page 164
The Screen modes change cyclically with each press of the SCREEN mode key. Note: The actual shape of the cursor is " [ ] ". The position of the cursor in this figure is different from the actual position on the screen. PRO-730HD...
Page 165
(CONTRAST +10) and decreases with the VOL- key (CONTRAST -40). (The brightness can be changed only in Fine- If an adjustment point is Peripheral points may adjustment mode. The brightness of the cross hatch screen greatly moved to the right, be affected. cannot be changed.) PRO-730HD...
Page 166
SKEW upper half of the screen first, then the lower half. (See 3.4.) SUBPIN SUBPIN SIZE SIZE SIZE SIZE Upper half : Adjust from the edge toward the center. Lower half : Adjust from the center toward the edge. PRO-730HD...
Page 167
Repeat the adjustments described in 3.6.2 and 3.6.3 so that all the screen, then the left half. Adjustment should be done from the red vertical and horizontal lines converge with the green lines. part where convergence is greatly dislocated. (Completion of one screen mode) PRO-730HD...
Page 168
At the TP-BK of the B CRT DRIVE Assy, check that the signal is shaped as shown below. OFFSET Saturated Shapely waveform Shapeless waveform "Normal video signal" CONTRAST After the STD adjustment is complete, adjust the 33K COMP and PURE RGB. PRO-730HD...
Page 169
Do not move the screen VR. : CUT-G Cut-G can be adjusted with little movement in STD OFFSET mode. Note : Refer to the following adjustment procedure. After the STD adjustment is composite adjustment the 33k Component and PURE RGB. PRO-730HD...
Page 170
Check that the value is the same as that for R CUT CH+ G CUT COMP (33 kHz). If it is not, enter the same value CH+ G CUT CH– B CUT as that for COMP (33 kHz). CH– B CUT PRO-730HD...
Page 171
CH– B CUT – 2 MODULE COLOR TINT CONTRAST BLACK LVL SHARPNESS DETAIL R DRV B DRV R CUT CH+ G CUT CH– B CUT ADJ :Adjustment item The numerical value is shipping a set value in the factory. PRO-730HD...
Page 172
• When perform the above adjustment, and display "END NG", input a value of "45". (Method refers to the following.) Start 1st FAC < Data value > AUTO ACL ADJUST AUTO ACL ADJUST SUB CH START ? EEPROM WRITE! Data value Data value: 45 PRO-730HD...
Page 173
Adjust so that the level of the luminosity of the panel and that of the main screen become the same. Approx. 0V Main screen (white) The level of the panel part changes with the CONTRAST data. The level of the main screen heightens or lowers in the reverse direction. PRO-730HD...
Page 174
• Send a 100%-white 480P signal to the INPUT 1 connector. • When 480P signal is not obtained and adjustment does not complete, input a value the same as BRIGHT and the CONTRAST data value that adjusted with step PRO-730HD...
VIDEO UCOM SERVICE Assy is defective. If the same symptom occurs, replace the POWER SUPPLY Assy. In the latter case, the VIDEO UCOM SERVICE Assy may not be defective. SIGNAL and TUNER Assemblies also perform the same thing as VIDEO UCOM SERVICE Assy, and exchange the unit that verified the unit and has broken. PRO-730HD...
Page 176
Check that the electric potential of pin 3 and pin 4 of IC401 Q404, Q402 CONVER. MUTING not activated and IC402 are at the same level when the power is turned on. (POWER SUPPLY Assy) PRO-730HD...
Page 177
3. Block Diagram of the Protection Circuit POWER SW ASSY POWER SUPPLY ASSY (AWZ6713) (AWV1960) VIDEO UCOM SERVICE ASSY (AWV1992) PRO-730HD...
Page 178
DEFLECTION SERVICE ASSY (AWV1967) PRO-730HD...
(Remote control unit key is impossible.) Standby LED starts flashing RETURN when presses a key more than five seconds. POWER RETURN Press it within five seconds. INPUT Flat-blade Screw Driver Cloth Start with the service factory mode. Frame Cover H PRO-730HD...
Page 180
If stains persist, use undiluted alcohol. ×2 AR Panel ×2 ×2 Remove the Panel Frame H Remove the Panel Frame V Panel Frame H Remove five screws Remove the Panel Frame H Panel Frame V Panel Frame V Panel Frame H ×5 PRO-730HD...
Page 181
Upper Cabinet Metal ×2 Upper Cabinet Metal Screen Side Fitting Notes: Screen Side To assemble the screen, perform the above procedures in Fitting ×2 reverse order. After assembling it, put positions together so that right and left ×2 become equal. PRO-730HD...
Page 182
POWER SUPPLY assy) Pull straight up Cover Pull straight up Note : When reconnecting the cable, proceed in the reverse order. After reconnecting, tug on the cable to check that it is secure. Rear View DEFLECTION SERVICE Assy PRO-730HD...
Yoke Wire Purse Lock Purse Lock FBT Focus Wire more than 15 mm Focus VR (VR1) Binder 10 cm more than 15 mm FBT Focus Wire At least 15 mm away from any other parts. Binder 5 cm HV Distributor PRO-730HD...
Page 184
Rear Section R 30 mm more than 15 mm Anode Cable R 50 mm DEFLECTION SERVICE Assy POWER SUPPLY Assy PRO-730HD...
7.1.4 ABOUT THE SERVICE (RS-232C) PORT Rear Panel INPUTS S-VIDEO CONTROL SERVICE ONLY INPUT 1 INPUT 2 INPUT 3 • Specification of this port is not decided at present. Please refer to the service information issued separately after specification was decided. PRO-730HD...
Page 186
Output voltage (V) current (I) 1.8V 2.5V 3.3V PQ018EZ01ZP PQ025EZ01ZP PQ033EZ01ZP TC7SB66FU (VIDEO UCOM SERVICE ASSY : IC4612, IC4613, IC4614) Single Bus Switch (analog) Pin Assignment (Top view) Block Diagram Inputs Function A port = B port Disconnect B GND PRO-730HD...
Page 187
TC7W53FU (VIDEO UCOM SERVICE ASSY : IC4603) Logic IC Pin Assignment (Top view) Block Diagram PQ30RV21 (DEFLECTION SERVICE ASSY : IC1001) Low Power-Loss Voltage Regulators Pin Assignment (Top view) Block Diagram Output Output voltage (V) Reference voltage precision: ± 2% current (I) PQ30RV21 PRO-730HD...
Page 188
M62399FP (VIDEO UCOM SERVICE ASSY : IC1905) 8-Bit D-A Converter with Buffer Amplifiers Pin Assignment (Top view) Block Diagram Pin Function PRO-730HD...
Page 189
(VIDEO UCOM SERVICE ASSY : IC4302, IC4303, IC4307) 2 Channel Analog Multiplexer Pin Assignment (Top view) Features Output Output voltage (V) current (I) 5V output PQ05DZ11 Block Diagram 24LC02B(I)SN (DVI SERVICE ASSY : IC6003, IC6014) Serial EEPROM Pin Assignment (Top view) Pin Function Block Diagram PRO-730HD...
Page 190
24LC64(I) P (DIGITAL CONV. ASSY : IC1203) Serial EEPROM Pin Assignment (Top view) Pin Function Block Diagram STK392-180 (POWER SUPPLY ASSY : IC401, IC402) Power Pack IC for TV Block Diagram Equivalent Circuit PRO-730HD...
Page 191
M52055FP (VIDEO UCOM SERVICE ASSY : IC2804, IC2805, IC4305, IC4306, IC4601) (SIGNAL ASSY: IC3907) 3ch Analog SW IC Block Diagram Pin Function Pin No. Symbol Equivalent Circuit Description of terminal Input terminal Output terminal Pulse Input terminal PRO-730HD...
Page 235
Serial input and output mode change signal input ACLOFF ACL OFF signal output at the time of AUTO ACL. CMUTE Conver mute output RESET Reset input XOUT Output terminal of system clock generating circuit Input terminal of system clock generating circuit PRO-730HD...
Page 236
4:3 panel signals, component signal / RGB signal change (MD) MMUTE Main video mute signal SMUTE Sub video mute signal 3DRST Reset signal output for 3-dimensional YC (MCOMPSW) Main video signal composite / component change signal Sub video signal composite / component change signal (SCOMPSW PRO-730HD...
Page 237
External parts for sub CCD timing signal generating circuits are connected. SCCY Picture signal input for small screen V CHIP detection (1.5Vpp) TVSETB Test input terminal (it fixes to Lo) VCCE STB5V MCCY Picture signal input for parent screen V CHIP detection (1.5Vpp) ( ) is undecided. PRO-730HD...
RGB signals are input. • The RGB input jack is designed for use in connecting a digital tuner with RGB signal output, and it should accordingly never be used for connecting to a personal computer or other device. PRO-730HD...
Page 239
When mute is turned on, a volume indicator will appear in red on the screen (and will disappear in a few seconds). If the MUTING button is pressed while a closed caption signal is being received, CC/TEXT will be displayed. Press MUTING again to return to the previous volume level. PRO-730HD...
Page 240
(S) Explicit sexual activity contains material that parents may find unsuitable (V) Graphic violence for younger children. The program contains one or more of the following: (D) Some suggestive dialogue (L) Infrequent coarse language (V) Moderate violence (S) Some sexual situations PRO-730HD...
Page 241
13. Programming is not suitable for children under the age of 16 (16 ans+) Contains frequent scenes of violence or intense violence. Programming restricted to adults (18 ans+) Contains constant violence or scenes of extreme violence. PRO-730HD...
Page 242
R A T I N G S Y S T E M C A N A D I A N R A T I N G S Y S T E M SET/ ENTER E X I T SELECT MENU PRO-730HD...
Page 243
T V — MA V — — V V V ‘View’ or ‘Block’ without regard to other ratings. E X I T SELECT MENU • Each time the SET/ENTER button is pressed, the setting will toggle between ‘B’ (Block) and ‘V’ (View). PRO-730HD...
Page 244
B L O C K ENTER 1 6 + : B L O C K 1 8 + : B L O C K E X I T SELECT MENU 13. After setting, press MENU to turn the menu off. TV/SAT/DVD MENU PRO-730HD...
Page 245
If you forget the password “PROGRAM BLOCKED”. When the message ‘INPUT YOUR PASSWORD’ in step 3 is displayed, press the RETURN button on the front panel and hold it down for 3 seconds or longer. The password reverts to “1234”. PRO-730HD...
Page 246
• If the non-interlace signal for a TV game etc. is entered to the left screen during SPLIT screen mode, the right screen may be disrupted. If this occurs, use the right screen for TV game etc. entry. PRO-730HD...
Page 247
9 screen or 4 the yellow arrow. (Use only the selector buttons, direct channel selection screen modes, the screen may be disrupted. buttons if channel, antenna or CH +,– buttons.) • Sound output is limited to the main picture. PRO-730HD...
Page 248
• It is not possible to adjust all these points (points of change on the cross-hatch). • Some of the cross-hatch lines are not straight, but this is not a malfunction. They are not always straight on a normal TV. PRO-730HD...
Page 249
INPUT SELECT, or MENU button on the front panel or on the remote control. Pushing the POWER button sets it in standby status. Control panel of the monitor STANDBY ROOM LIGHT SENSOR PRO-730HD...
Page 250
• Setting SYSTEM MODE ON will cause RGB input signals and DIGITAL input signals to not be displayed. • Changing Screen Mode • When 1080i, 720p component signals or RGB signals, 1080i DIGITAL signals are input, SCREEN MODE will be limited to FULL. PRO-730HD...
Press plus (+) button to increase the volume, press minus (-) button to decrease it. Press to select or adjust items on the menu screen. MAIN POWER STANDBY/ON SELECT STANDBY ROOM LIGHT SENSOR POWER INPUT CHANNEL MENU MENU MENU ACCESS PRO-730HD...
Page 252
MODE: NATURAL WIDE button. If the normal operation cannot be restored after the above RLS: treatment, immediately unplug the power cord and call SYSTEM IN/OUT your nearest PIONEER-authorized service center. SPEAKER: NORMAL AUDIO OUT: FIXED NOTES: SYSTEM MODE: • On rare occasions, an electrical discharge may occur inside the CRT*.
Page 253
MENU 0 ANT (antenna selector) button LEARN SOURCE Press to switch between ANTENNA-A and ANTENNA-B DTV/SAT when you wish to watch TV. GUIDE POWER SET/ ENTER DTV/SAT INFO VCR REC FAVORITE CH ¡ RECEIVER INPUT Î HDTV PROJECTION MONITOR PRO-730HD...
Page 254
SPLIT screen. ~ CH ENTER button Fix the selected channel with the direct channel selection buttons. ! CH RETURN (channel return) button Press to switch between the current channel and the channel you were watching immediately before. PRO-730HD...