Table of Contents
Advertisement
during start-up. The operator can control torque reac-
tions or kickback forces, if proper precautions are taken.
Never place your hand near the rotating accessory.
u
Accessory may kickback over your hand.
Do not position your body in line with the rotating
u
wheel. Kickback will propel the tool in direction opposite
to the wheel's movement at the point of snagging.
Use special care when working corners, sharp edges
u
etc. Avoid bouncing and snagging the accessory.
Corners, sharp edges or bouncing have a tendency to
snag the rotating accessory and cause loss of control or
kickback.
Do not attach a saw chain, woodcarving blade, seg-
u
mented diamond wheel with a peripheral gap greater
than 10 mm or toothed saw blade. Such blades create
frequent kickback and loss of control.
Do not "jam" the wheel or apply excessive pressure.
u
Do not attempt to make an excessive depth of cut.
Overstressing the wheel increases the loading and sus-
ceptibility to twisting or binding of the wheel in the cut
and the possibility of kickback or wheel breakage.
When wheel is binding or when interrupting a cut for
u
any reason, switch off the power tool and hold the
power tool motionless until the wheel comes to a com-
plete stop. Never attempt to remove the wheel from
the cut while the wheel is in motion otherwise kick-
back may occur. Investigate and take corrective action
to eliminate the cause of wheel binding.
Do not restart the cutting operation in the workpiece.
u
Let the wheel reach full speed and carefully re-enter
the cut. The wheel may bind, walk up or kickback if the
power tool is restarted in the workpiece.
Support panels or any oversized workpiece to minim-
u
ize the risk of wheel pinching and kickback. Large
workpieces tend to sag under their own weight. Supports
must be placed under the workpiece near the line of cut
and near the edge of the workpiece on both sides of the
wheel.
Use extra caution when making a "pocket cut" into ex-
u
isting walls or other blind areas. The protruding wheel
may cut gas or water pipes, electrical wiring or objects
that can cause kickback.
Additional Safety Information
Wear hearing protection, pro-
tective goggles, a dust mask
and gloves. Use at least an FFP
2 protection class particle-fil-
tering half mask.
Use clamps or another practical way to secure and
u
support the workpiece to a stable platform. Holding
the work by your hand or against the body leaves it un-
stable and may lead to loss of control.
Use suitable detectors to determine if utility lines are
u
hidden in the work area or call the local utility com-
pany for assistance. Contact with electric lines can lead
to fire and electric shock. Damaging a gas line can lead to
Bosch Power Tools
explosion. Penetrating a water line causes property dam-
age or may cause an electric shock.
Do not touch the cutting disc after use before it has
u
cooled. The cutting disc becomes very hot during use.
Hold the power tool firmly with both hands and make
u
sure you have a stable footing. The power tool can be
more securely guided with both hands.
Products sold in GB only:
Your product is fitted with an BS 1363/A approved electric
plug with internal fuse (ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets, it should be
cut off and an appropriate plug fitted in its place by an au-
thorised customer service agent. The replacement plug
should have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.
Product Description and
Specifications
Read all the safety and general instructions.
Failure to observe the safety and general in-
structions may result in electric shock, fire
and/or serious injury.
Please observe the illustrations at the beginning of this oper-
ating manual.
Intended Use
The power tool is intended to be used on a stable surface,
with the base plate and the protective guard fitted, to cut or
score horizontally into predominantly mineral materials, e.g.
marble, without using water. The power tool is not suitable
for cutting wood, plastic or metal.
Product Features
The numbering of the product features refers to the diagram
of the power tool on the graphics page.
(1)
On/off switch
(2)
Lock-on button for on/off switch
(3)
Handle (insulated gripping surface)
(4)
Cutting depth scale
(5)
Wing bolt for preselecting the cutting depth
a)
(6)
Diamond cutting disc
(7)
Direction-of-rotation arrow for grinding spindle
(8)
Protective guard
(9)
Base plate
(10)
Drive spindle
(11)
O-ring
(12)
Mounting flange
(13)
Clamping flange
(14)
Ring spanner
(15)
Clamping bolt
English | 7
1 609 92A 6FJ | (11.03.2021)
Advertisement
Table of Contents
