D-Link ENW-3503 User Manual
  1. Manuals
  2. Brands
  3. D-Link Manuals
  4. Modem
  5. ENW-3503
  6. User manual
D-Link ENW-3503 User Manual

D-Link ENW-3503 User Manual

Ethernet + fax/modem multifunction pc card
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
ENW-3503
Ethernet + Fax/Modem
Multifunction PC Card
User' s Manual
PLANET ENW-3503 User's Manual

Advertisement

Table of Contents
loading

Related Manuals for D-Link ENW-3503

Summary of Contents for D-Link ENW-3503

  • Page 1 ENW-3503 Ethernet + Fax/Modem Multifunction PC Card User’ s Manual PLANET ENW-3503 User's Manual...
  • Page 2 FCC REGULATORY STATEMENTS FCC Certification Ethernet + 56K Fax/Modem PC Card FCC ID: MQ4LM560T The United States Federal Communication Commission (FCC) and the Canadian Department of Communications have established certain rules governing the use of modems and other electronic equipment. FCC Part 68 Registration This high speed Ethernet + FAX/MODEM PC Card complies with FCC Part 68 rules, and the use of this modem is subject to the following restrictions:...
  • Page 3 All other trademarks belong to their respective owners. Revision This user's manual is for PLANET PCMCIA LAN + FAX/MODEM PC Card model -- ENW-3503 Rev: 1.00 (May, 1998) Part No: EM3503...

  • Page 4: Table Of Contents

    TABLE OF CONTENTS 1. INTRODUCTION ............1-1 1.1. ABOUT THIS MANUAL........1-1 1.2. ABOUT ENW-3503 ..........1-1 1.2.1. Specifications..........1-2 1.2.2. Features............1-2 1.3. SYSTEM REQUIREMENTS ........1-3 1.4. PACKAGE CONTENTS.........1-3 2. INSTALLATION ............2-1 2.1. HARDWARE INSTALLATION ......2-1 2.2. INSTALLING THE SOFTWARE ......2-2 2.2.1. Novell Netware Installation......2-3 2.2.2.
  • Page 5 8.3. E "AT" (B ..8-6 XTENDED LASH OMMAND 8.4. E "AT%" (P ..8-7 XTENDED ERCENT OMMAND 8.5. E "AT-" (D ....8-8 XTENDED OMMAND 8.6. R ..........8-8 ESULT PTIONS 8.7. E ....8-10 XTENDED ESULT PTIONS ABLE 8.8. S-R , "ATS " ........8-12 EGISTERS...

  • Page 7: Introduction

    Ethernet + Fax/Modem PC Card -- ENW-3503. 1.2. ABOUT ENW-3503 The PC Card -- ENW-3503 is a multifunction communication device that lets you perform multiple communication tasks at the same time: (1) transmit and receive data up to 56,000 bps...

  • Page 8: Specifications

    1 INTRODUCTION enable you to successfully access to the servers on Ethernet LAN and hook up to the Internet, transmit E-Mail, send and receive information and communicate with other PCs, Bulletin Board Services (BBS) or on-line computer networks such as CompuServe and America On line.

  • Page 9: Features

    • RJ45 jack for 10Base-T connectivity to your network resources • Driver software loaded on your PC • Data and/or fax communications software. 1.4. PACKAGE CONTENTS • Multifunction ENW-3503 PC Card • PCMCIA cable with RJ-11 and RJ-45 plugs PLANET ENW-3503 User's Manual...
  • Page 10 1 INTRODUCTION • A 3-1/2” driver diskette • User’s Manual • Windows-based fax/modem application program • RJ-45 extension connector for LAN • RJ-11 extension connector for Fax/Modem LAN + Fax/Modem PC Card...

  • Page 11: Installation

    INSTALLATION This chapter describes how to install your ENW-3503 PC Card. Installation procedures also cover many popular Network Operating Systems. 2.1. HARDWARE INSTALLATION 1. Hold the card label up and insert the card into the computer's PCMCIA slot with the 68 pin connector facing the computer.

  • Page 12: Installing The Software

    2 INSTALLATION 2.2. INSTALLING THE SOFTWARE For Non-Windows 95 & Windows NT System Plug the driver diskette into the floppy drive and set the current drive to the floppy drive (A:\). Then run INSTALL to install the dirver. LAN + Fax/ Modem PC Card...

  • Page 13: Novell Netware Installation

    OK to exit. 5.Installation program starts installing drivers and modifying AUTOEXEC.BAT and NET.CFG. Select Yes then press Enter to modify the files. 6. Now, the installation is completed. 7. Restart your computer to make Netware connections. PLANET ENW-3503 User's Manual...

  • Page 14: Ms Lan Manager Installation

    2.2.2. MS LAN Manager Installation 1.Cast a look at the README.TXT in the \NDIS2 directory in ENW-3503 PC Card driver disk. Before installing the drivers, please ensure that the Microsoft LAN Manager has been installed in the target path. The installation program will check and modify the PROTOCOL.INI file for LAN...

  • Page 15: Packet Driver Installation

    NCBS = 12 BINDINGS = "LMNDIS_NIF" LANABASE = 0 [LMNDIS_NIF] ; protocol.ini session for multifunction LAN/MODEM driver. IOADDRESS = 0x320 INTERRUPT = 11 DRIVERNAME = LMNDIS$ 2.2.3. Packet Driver Installation 1.Run INSTALL.EXE file driver diskette (A:\INSTALL). PLANET ENW-3503 User's Manual...

  • Page 16: Windows For Workgroups 3.11 Installation

    Enter to modify the files. 6.Now, the installation is completed. 7.Reboot the computer to load driver. 2.2.4. Windows for Workgroups 3.11 Installation 1. Run INSTALL.EXE in root directory of ENW-3503 PC Card driver disk. 2. Select Windows for Workgroup in Network Operating System screen.

  • Page 17: Windows Nt 3.51 & Nt 4.0 Installation

    -- remove all existing network components Note: remove all adapters first, then servers, then workstations, etc. 4. Remove all serial port support -- open Program Manager à Main group à Control Panel à Ports -- remove all the COM port devices PLANET ENW-3503 User's Manual...
  • Page 18 Check Event Viewer when system reboots. Ask your laptop dealer for help if any problems occur during the pre- installation. ENW-3503 PC Card Installation in NT 3.51 1. Insert the Ethernet + /Fax/Modem multifunction PC Card into one of the PCMCIA slots 2.
  • Page 19 Card then press OK. 13. A dialog box will be poped up for the driver settings change. 14. Give appropriate system resources to the ENW-3503 PC Card, the settings must be unique for this device. Resources Recommendation I/O Base I/O:300.
  • Page 20 7. Press CLOSE after all serial port devices are removed. ENW-3503 PC Card Installation in NT 4.0 1. Insert ENW-3503 PC Card into one of the PCMCIA Slots 2. Start Windows NT 4.0 3. Login with a full access level ADMINISTRATOR 4.
  • Page 21 2 INSTALLATION ♦ select the only one choice for the ENW-3503 PC Card, then press OK and NEXT ♦ Windows NT 4.0 will grant configurations for -- TCP/IP -- NWLink IPX/SPX -- NetBEUI These configurations are unique for each network. If you want to change them, ask your network administrator for help.

  • Page 22: Windows 95 Installation

    Control Panel can report on its functionality. If not, check your computer dealer for technical support. 2.Insert ENW-3503 PC Card into PCMCIA slot. Windows 95 will prompt New Hardware Found dialog box. In New Hardware Found dialog box, select Driver from disk provided by hardware manufacturer.

  • Page 23: Artisoft Lantastic 6.0 Installation

    2 INSTALLATION 3.Enter the correct path, i.e. “A:\”, then insert ENW-3503 PC Card driver disk. The driver will be installed automatically, and system may ask for the Windows 95 installation CD/disks to update the existing files or drivers. After the update, system will reboot automatically.
  • Page 24 2 INSTALLATION 5.Move cursor to each field you want to make modification and press Enter to set correct value. Then press Enter on the OK. 6.Installation program starts copying drivers and modifying CONFIG.SYS, PROTOCOL.INI, and STARTNET.BAT. 7.Reboot the computer to have the driver take effect. 2-14 LAN + Fax/ Modem PC Card...

  • Page 25: Modem Basics

    This chapter covers the basic commands and techniques involved in modem operation. In many cases, this is the only information you will need in order to get your ENW-3503 PC Card up and running with communication software, and to start making connections with your PC Card.
  • Page 26 “customize” the settings of your ENW-3503 PC Card, or store phone numbers you commonly connect to. Once the ENW-3503 PC Card is connected to your computer’s serial port and telephone line, open the Windows 95 “Accessories” program group, and open the Hyper Terminal Program.
  • Page 27 Auto-Answer and Hook Controls Enabling Auto-Answer: ATS0=n Note: In this example, n is a number from 1 to 255 that corresponds to the number of rings after which your modem answers an incoming call. Disabling Auto-Answer: ATS0=0 PLANET ENW-3503 User's Manual...
  • Page 28 3 MODEM BASICS Manually Answering a Call: Take modem off-hook: ATH1 Hang up modem (on-hook): ATH0 Manually Disconnecting a Call: +++ATH LAN + Fax/ Modem PC Card...

  • Page 29: Drivers Information

    (1,2,3,4) to the driver, there has been another field added. The section of the PROTOCOL.INI file that contains configuration information for this card must begin with [LMNDIS_NIF]. The valid entries in the file are listed below: [LMNDIS_NIF] DRIVERNAME - LMNDIS$ PLANET ENW-3503 User's Manual...

  • Page 30: Notes For Packet Driver

    3 MODEM BASICS This line must always be presend IOADDRESS - value where value is one of the following address: 0x300, 0x320, 0x340, 0x360. The leading 0x for the hex notation is required. To have Card Services select the address base from it's pool of available address then use a value of 0. INTERRUPT - value where values is one of the following interrupts: 3, 4, 5, 7, 9, 10, 11, 12, 15.
  • Page 31 CONFIG.SYS AUTOEXEC.BAT for loading System Soft’s Card Services and drivers for Windows for Workgroups: Examples of CONFIG.SYS file: device=c:\cardsoft\ss365sl.exe device=c:\cardsoft\cs.exe device=c:\cardsoft\csalloc.exe c:\cardsoft\csalloc.ini device=c:\wfw311\carden.exe /iop=nnn /irq=n /com=n /mir=n device=c:\cardsoft\cardid.exe device=c:\wfw311\ifshlp.sys Examples of AUTOEXEC.BAT file: C:\WFW311\NETSTART PLANET ENW-3503 User's Manual...
  • Page 33 C:Make sure the modem is not in Data Mode. type +++ if necessary. C:Make sure your software is set to the same COMx: port as the modem is. Q:The modem does not give a response after an AT command was executed. PLANET ENW-3503 User's Manual...

  • Page 34: Q & A

    5. Q & A C:The echo and/or responses may be turned off by the ATE0Q1 commands. Use AT&V to check that. A:Use ATE1Q0 then Enter to change them back. C:Make sure the modem is in Command Mode not in Data Mode when you type the AT command.
  • Page 35 C:If you are using touch tone dialing on a phone line that requires pulses, then it may not work. Use ATDT in place of ATDP. Q:When your communications software tells the modem to dial, it does not. C:Make sure the software dialing prefix is ATDT. PLANET ENW-3503 User's Manual...
  • Page 36 5. Q & A C:Make sure the software and modem are set to the same COMx: port. C:The modem may not have hung up the phone line since the last call. A:Change to command mode and type ATH then press Enter. Q:The modem can connect to some modems, but not others.
  • Page 37 Q:The text on the screen is not legible. C:Your software settings may not match the settings on the remote site. A:Make sure your data bits, stop bits, and parity settings match the settings that the other computer is using. The two PLANET ENW-3503 User's Manual...
  • Page 38 5. Q & A most common settings are: 8 data bits, None parity, and 1 stop bit (8,N,1) or 7 data bits, Even parity, and 1 stop bit (7,E,1). C:If the telephone line is very noisy, you may see corrupted data on your screen.
  • Page 39 A:Run CARDEN /CHK to check, if the card has been enabled. The resources allocated for the card are shown as below at the last line of display message. “ IOP=0Xnnn IRQ=nn COM=nn MIR=nn” Q: How to install the Win 95 driver over SystemSoft CardWorks ? PLANET ENW-3503 User's Manual...
  • Page 40 5. Q & A A:1.Start the Win 95 then plug the LAN/Modem card into the PCMCIA slot. The SystemSoft Cardwizard window should appear. 2.Select the appropreate slot number which the LAN/Modem card is plugged in. 3.Select View pull down menu 4.Select Properties.

  • Page 41: Appendix A: Ndis2 And Odi Drivers For Wfw 3.11

    12.Move cursor to the setting you want to make a change for then press Enter to select a fit value. When the configuration is set completely, press Enter on the OK field to exit the screen then go back to step 11. PLANET ENW-3503 User's Manual...
  • Page 42 Appendix A 13.Select NDIS Server(LAN Manager,...) as the network server that you will attach to then press Enter key. 14.Installation program starts to copy related files to the destination directory and modifies AUTOEXEC.BAT under user‘s agreement. 15.Reboot the computer to let the driver take effect. ODI Driver for Workgroups 1.Run Windows for workgroups and click Network Setup icon in Network group.
  • Page 43 Enter key. 14.Installation program starts to copy related files to the destination directory and modifies AUTOEXEC.BAT and NET.CFG under user‘s agreement. 15.Reboot the computer to let the driver take effect. PLANET ENW-3503 User's Manual...

  • Page 45: Appendix B: Uninstallation The Ethernet + Faxmodem In Win 95

    Device Manager folder of System in Control Panel program group. Supposedly the Intelligent xxxxx (Modem) Card in Modem properties and the Intelligent xxxxx (Ethernet) Card in Network adapters properties will be removed automatically. If not, remove them manually. PLANET ENW-3503 User's Manual...
  • Page 46 2. Click Start button in Windows 95 main screen then select Run… . 3. Insert the Ethernet + Fax/Modem Program (Driver) Disk, then enter A:\delinf.exe then click on OK. 4. Re-start Windows 95. Now the ENW-3503 PC Card is completely uninstalled. LAN + Fax/ Modem PC Card...
  • Page 47 Appendix B PLANET ENW-3503 User's Manual...

  • Page 49: Appendix C: Fax/Modem At Command

    Select Bell 103 for 300bps connection Dial command, beginning the dialing sequence. The string "n" (telephone number and modifiers) listed as follows is entered after the "D" command Re-dial last number. Should be the first character following ATD, ignored PLANET ENW-3503 User's Manual...
  • Page 50 Appendix C otherwise Pulse dial. Reverse dial. Originate call in answer mode (go on-line in answer mode) Dial the phone number stored in NVRAM at location "n" (n=0, 1, 2, 3) DTMF tone dial Wait for second dial tone. The modem waits for the second dial tone before processing the dial string Pause.
  • Page 51 Select result codes/call progress options Display CONNECT or "1" for all speeds. Ignore dial tone and busy tone detection Display connect message and the modem's data rate, and an indication of the modem's error correction and data PLANET ENW-3503 User's Manual...

  • Page 52: Extended "At&" (Ampersand) Command Set

    Appendix C compression. Ignore dial tone and busy tone detection Display connect message and the modem's data rate, and an indication of the modem's error correction and data compression. Check dial tone before proceeding dialing, ignore busy tone detection Display connect message and the modem's data rate, and an indication of the modem's error correction and data compression.
  • Page 53 &P1 Make=33%, Break=67%, international version. Make=33%, Break=67% for use in 10 pps, Japanese version (Default) &Qn Async communications mode options &Q0 Async mode, buffered (same as "AT\N0") &Q5 * Error control mode, buffered (same as "AT\N3") PLANET ENW-3503 User's Manual...
  • Page 54 Appendix C &Q8 MNP error control mode. If an MNP error control protocol is not established, the modem will fallback according to the current setting in S36 register &Q9 V.42 or MNP error control mode. If neither error control protocol is established, the modem will fallback according to the current setting in S36 register &Sn...
  • Page 55 * Disable inactive timer n=1 - Enable inactive timer. Length in minutes Protocol result codes Disable protocol result code appended to DCE speed \V1 * Enable protocol result code appended to DCE speed *: Manufacturer default PLANET ENW-3503 User's Manual...
  • Page 56 Appendix C 8.4. Extended "AT%" (Percent) Command Command Options Function & Description View numbers in blacklist. If blacklisting is in effect, this command displays the numbers for which the last call attempted in the past two hours failed. The ERROR result code appears in the countries that do not require blacklisting.
  • Page 57 CONNECT 42000 EC * CONNECT 44000 EC * CONNECT 46000 EC * CONNECT 48000 EC * CONNECT 50000 EC * CONNECT 52000 EC * CONNECT 54000 EC * CONNECT 56000 EC * CONNECT 16800 EC * PLANET ENW-3503 User's Manual...
  • Page 58 Appendix C CONNECT 115200 EC * % % % % DELAYED ** BLACKLISTED ** BLACKLIS FULL ** : DTE/DCE speed : DCE speed (line speed) : DTE speed : EC only appears when the Extended Result Code options are enabled :For Blacklisting function enabled countries only 8.7.
  • Page 59 CONNECT 40000 EC* CONNECT 42000 CONNECT 42000 EC* CONNECT 44000 CONNECT 44000 EC* CONNECT 46000 CONNECT 46000 EC* CONNECT 48000 CONNECT 48000 EC* CONNECT 50000 CONNECT 50000 EC* CONNECT 52000 CONNECT 52000 EC* CONNECT 54000 PLANET ENW-3503 User's Manual 8-11...
  • Page 60 Appendix C CONNECT 54000 EC* CONNECT 56000 CONNECT 56000 EC* CONNECT 16800 CONNECT 16800 EC * CONNECT 115200 CONNECT 115200 EC * *: EC is replaced by one of the following symbols. V.42bis V.42 error control and V.42bis data compression V.42 V.42 error control only MNP5...
  • Page 61 1-255 second, that the modem waits before hanging up after a loss of carrier S11= DTMF duration and inter digit delay. Set the duration and spacing, in mini- 50-150 seconds, in DTMF touch tine dialing PLANET ENW-3503 User's Manual 8-13...
  • Page 62 Appendix C S12= Define the maximum period, in 2- 0-255 hundredths of a second, allowed between consecutive asynchronous escape character "+" for the escape sequence to be considered valid S28= V.34 modulation en-/disabler 0: disabled 0-255 1- 255: enabled S30=0-90 Inactivity timer.
  • Page 63 S36=1 or 3, and S48=7 LAPM or async S36=1 or 3, and S48=128 Async S36=4 or 6, and S48=7 LAPM, MNP or hang up S36=4 or 6, and S48=128 MNP or hang S36=5 or 7, and S48=7 LAPM, MNP or PLANET ENW-3503 User's Manual 8-15...
  • Page 64 Appendix C async S36=5 or 7, and S48=128 MNP or hang S89= Sleep mode control timer. Specify the number of seconds of inactivity (no 0,5-60 character sent from DTE, no RING) in the off-line command state before the modem places itself into standby mode. A value of "0"...

Table of Contents