Sony CDX-1000RF Operating Instructions page 2

Connect ions
Caut ion
•This unit is designed for negative ground 12 V DC operation only.
•Before making connections, disconnect the ground terminal of the car battery to avoid short circuits.
•Connect the yellow and red power input leads only after all other leads have been connected.
•Be sure to connect the red power input lead to the positive 12 V power terminal which is energized
when the ignition key is in the accessory position.
• Run all ground w ires to a common ground point.
•Connect the yellow cord to a free car circuit rated higher than the unit's fuse rating.
If you connect this unit in series with other stereo components, the car circuit they are connected to
must be rated higher than the sum of the individual component's fuse rating.
If there are no car circuits rated as high as the unit's fuse rating, connect the unit directly to the
battery.
If no car circuits are available for connecting this unit, connect the unit to a car circuit rated higher
than the unit's fuse rating in such a way that if the unit blows its fuse, no other circuits will be cut
off.
•The use of optical instruments with this product will increase eye hazard.
Reset but t on
When the installation and connections are complete, be sure to press the reset button with a ball-point
pen, etc.
AMS
SHUF DSPL
REPEAT OFF
Reset button
Connect ion exam ple
To a metal point of the car
First connect t he black ground lead, t hen connect t he yellow
and red pow er input leads.
To the +12 V pow er terminal w hich is energized in
the accessory position of the ignition key
Be sure t o connect t he black ground lead f irst .
To the +12 V pow er terminal w hich is energized at
all times
Be sure t o connect t he black ground lead f irst .
Rotary commander RM -X4S *
(not supplied)
If you have a Sony car audio w ith the Sony BUS terminal, the optional source selector
XA-107 can be used in your system.
Sony car audio
AUDIO IN BUS CONTROL IN
AUDIO OUT M ASTER
Source selector
XA-107
AUDIO IN
AUDIO OUT
CDX-1000RF
Downloaded from: https://www.usersmanualguide.com/
Part s f or Inst allat ion and Connect ions
The numbers in the list are keyed to those in the instructions.
1 2
4 5
7 8
× 4
Caut ion
Cautionary notice for handling the bracket 1.
Handle the bracket carefully to avoid injuring your fingers.
Black Blue/ White
To AM P REM OTE IN
of the car audio *
0.5 m 0.5 m
AM P REM OTE OUT
(1 ft. 8 in.) (1 ft. 8 in.)
M ax. supply current 0.3 A
Fuse
Red
0.5 m
(1 ft. 8 in.)
1
* You can only connect a car audio w hich has both a remote
amplifier input (AM P REM OTE IN) and an audio input (AUDIO IN).
Fuse Note
Yellow
Do not connect an ext ernal amplif ier t o t he audio out put (AUDIO
OUT) of t his unit . Ot herw ise, t he volume of t he connect ed
0.5 m
speakers cannot be adjust ed.
(1 ft. 8 in.)
AUDIO OUT
8
L
R
AUDIO OUT
RCA pin cord
(not supplied)
REM OTE IN
1.9 m (6 ft. 3 in.)
2
0.5 m
(1 ft. 8 in.)
Car audio
3
Antenna connector *
2 You can also control the follow ing functions w ith the rotary cammander
*
RM -X4S:
Pow er on – Press SOURCE.
Pow er off – Press OFF.
Locate a specific track
– Rot at e t he SEEK/AM S cont rol moment arily and release.
Locate a specific point w ithin a track
– Rot at e t he SEEK/AM S cont rol and release w hen t he desired point is f ound.
Adjust the volume – Rot at e t he volume cont rol.
* 3 An adaptor (optional) may be necessary for your car and car audio system.
In such a case, consult your dealer.
Inst allat ion
Precaut ions
•Do not tamper with the four holes on the upper surface of the unit. They are for tuner adjustments to be
3
done only by service technicians.
•Choose the installation location carefully so that the unit will not hamper the driver during driving.
•Avoid installing the unit where it would be subject to high temperatures, such as from direct sunlight or
hot air from the heater, or where it would be subject to dust, dirt, or excessive vibration.
•Use only the supplied mounting hardware for a safe and secure installation.
M ount ing exam ple
6
Installation in the dashboard
1
1 8 2
m m
(7
1
× 2
9
1
With the TOP marking up
4
5
With the TOP marking up
1
M ount ing t he unit in a Japanese car
You may not be able to install this unit in some makes of Japanese cars. In such a case, consult your Sony dealer.
TOYOTA
7 max. size 5 × 6 mm
×
( 7 / 1 / in.)
32 4
Bracket
To AUDIO IN
1
of the car audio *
Existing parts supplied w ith your car
Note
From car antenna
To prevent malf unct ion, inst all only w it h t he supplied screw s 7.
Rem oving t he unit
Speaker system
Insert the supplied tool 9 betw een the unit and the frame, and rotate 90° to
1
release the hidden mounting spring. Repeat on the opposite side and remove
the frame.
10 mm ( 13 / in.)
32
M ount ing angle adjust m ent
Adjust the mounting angle to less than 60°.
2 3
/
4 in .)
5 3 m
m
(2 1
/
in .)
8
Bend these claw s, if necessary.
Note
To prevent malf unct ion, inst all
only w it h t he supplied screw s 7.
To support t he unit
1
2
NISSAN
7 max. size 5 × 6 mm
×
( 7 / 1 / in.)
32 4
Car audio w ith FM tuner
to dashboard/ center console
7 max. size 5 × 6 mm
×
( 7 / 1 / in.)
32 4
CDX-1000RF
Bracket
2 Insert a flathead screw driver betw een the bracket and mounting spring. Gently
pry the spring tow ard the unit w hile pulling the unit out a little. Repeat on the
opposite side and remove the unit.
9
90º
max. size 5 × 6 mm
7
7 × 1
( / / in.)
32 4
7
6
6
6 7
max. size 5 × 6 mm
7 × 1
( / / in.)
32 4
Fire w all
2
Dashboard
3 max. size M 4 × 6 mm
×
( 3 / 1 / in.)
16 4
4
1
Car audio w ith FM tuner
to dashboard/ center console
7 max. size 5 × 6 mm
×
7 1
Bracket ( / 32 / 4 in.)
CDX-1000RF
Bracket
Existing parts supplied w ith your car
4 mm ( 3 / in.)
16