The cyber-shot t5 combining 5.1 effective megapixels, a 2.5 inch lcd screen, and carl zeiss 3x zoom, with a super-slim vertical design aluminium body. (2 pages)
SPECIFICATIONS Camera [Power, general] Rechargeable battery pack [System] Power: Rechargeable battery pack NP-BD1, 3.6 V NP-BD1 NP-FD1 (sold separately), 3.6 V Image device: 7.79 mm (1/2.3 type) color CCD, Used battery: Lithium-ion battery AC-LS5K AC Adaptor (sold separately), Primary color filter Maximum voltage: DC 4.2 V 4.2 V Total pixel number of camera: Approx.
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU PUBLISHED BY SONY.
Page 5
ENGLISH JAPANESE ENGLISH JAPANESE 1. SERVICE NOTE 1-1. PRECAUTION ON REPLACING THE SY-225 BOARD RESTORE DATA When you replace to the repairing board, get the acquire data from the former needed for the adjustment from. Start the Adjust Manual in the Adjust Station and perform “RESTORE DATA” to get the data. The data getting for this model is as follows.
ENGLISH JAPANESE ENGLISH JAPANESE 1-3. METHOD FOR COPYING OR ERASING THE DATA IN INTERNAL MEMORY The data can be copied/erased by the operations on the HOME screen. (When erasing the data, execute formatting the internal memory.) Note 1: When replacing the SY-225 board, erase the data in internal memory of the board before replacement. Note 2: When replacing the SY-225 board, execute formatting and initialize the internal memory after replacement.
ENGLISH JAPANESE ENGLISH JAPANESE 1-4. HOW TO WRITE DATA TO INTERNAL MEMORY Usually, the camera has been set so as to disable the data writing from the PC to the internal memory of the camera. This setting must be changed temporarily when the data is to be written to the internal memory such as a case after the board replacement. To change settings is enabled with using the writing enabler tool (WriteEnableTool) on the Adjust manual is activating from the Adjust station.
ENGLISH JAPANESE ENGLISH JAPANESE 1-5. SELF-DIAGNOSIS FUNCTION 1-5-1. Self-diagnosis Function 1-5-2. Self-diagnosis Display When problems occur while the unit is operating, the self-diagnosis When problems occur while the unit is operating, the LCD screen function starts working, and displays on the LCD screen what to shows a 4-digit display consisting of an alphabet and numbers, which blinks at 3.2 Hz.
Page 9
ENGLISH JAPANESE ENGLISH JAPANESE 1-5-3. Self-diagnosis Code Table Self-diagnosis Code Block Detailed Symptom/State Correction Function Code The internal memory has experienced a Turn the power off and on again. media error. The internal memory has experienced a Format the internal memory. format error.
ENGLISH JAPANESE ENGLISH JAPANESE 1-6. PROCESS AFTER FIXING FLASH ERROR When “FLASH error” (Self-diagnosis Code E : 91 : 01) occurs, to prevent any abnormal situation caused by high voltage, setting of the flash is changed automatically to disabling charge and flash setting. After fixing, this setting needs to be deactivated.
Page 11
ENGLISH JAPANESE ENGLISH JAPANESE 1-1. SY-225基板交換時の注意 リストアデータ 補修用基板と交換する時,交換前の基板より調整に必要となるデータを取得してください。 データの取得はAdjust StationからAdjust Manualを起動させて「RESTORE DATA」を実行させてください。 本機で取得されるデータは下記になります。 ・ USB SERIAL No. ・ Angular Velocity Sensor sensitivity adj. (Dp/Dy/Fpy Data) ・ Wide Limit adj. Note:交換前の基板よりデータが読み取れない場合は,SY-225基板とレンズを同時に交換する必要があります。 仕向けデータ 補修用基板と交換する時,補修用基板に書かれている仕向けデータは元の設定と違っている場合があります。 Adjust StationからAdjust Manualを起動させて「DESTINATION DATA WRITE」を実行させてください。 USBシリアルNo. セットは,1台毎に異なる固有のID(USB Serial No.)を書き込んだ後,出荷されています。 新品の補修用基板には,このIDが書き込まれていないので,基板交換後にIDを入力する必要があります。 Adjust StationからAdjust Manualを起動させて「USB SERIAL No. INPUT」を実行させてください。 角速度センサ 補修用基板と交換する時,角速度センサ(SE401)の感度表示を書き留めてください。 Adjust StationからAdjust Manualを起動させて「Angular velocity sensor sensitivity adj.」を実行させて書き留めたデータを入力し てください。 SY-225 BOARD (SIDE B) SE401 PPP: PITCH感度表示 YYY: YAW感度表示 Note:SY-225基板のSE401感度表示は補修用基板にしか記載されておりません。 W端調整データ (2バイトデータ) XXYY 1-2. レンズ交換時の注意 レンズ交換時、補修用レンズ添付のPITCH/YAWデータ, FNデータおよびW端調整データを書き留めてください。...
Page 12
ENGLISH JAPANESE ENGLISH JAPANESE 1-3. 内蔵メモリーのデータコピーおよび消去方法 内蔵メモリーのデータコピーまたは消去はホーム画面の操作から実行可能です。(消去する場合は内蔵メモリーの初期化を行い ます。) Note1: SY-225基板交換の際は,基板交換前に内蔵メモリーのデータを消去して下さい。 Note2: SY-225基板交換の際は,基板交換後に内蔵メモリーのフォーマットおよび初期化を実行して下さい。 内蔵メモリーのコピー方法 コピー 内蔵メモリーに記録した画像を、 メモリースティック デュオ に一括コピーします。 1 充分な空き容量のある メモリースティック デュオ を本機に入れる (メモリー管理) [メモリーツール] HOME [コピー] [実行] ご注意 充分に充電したバッテリーをご使用ください。残量の少ないバッテリーを使用して画像ファイルを コピーすると、バッテリー切れのためデータを転送できなかったり、データを破損するおそれがあり ます。 画像ごとのコピーはできません。 データをコピーしても、内蔵メモリー内のデータは削除されません。内蔵メモリーの内容を消去す るには、コピー後に メモリースティック デュオ を本体から取りはずし、[内蔵メモリーツール]の [フォーマット]を行ってください。 データをコピーすると メモリースティック デュオ 内に新しいフォルダが作成されます。コピー先 のフォルダを指定することはできません。...
Page 13
ENGLISH JAPANESE ENGLISH JAPANESE 1-4. 内蔵メモリへデータを書き戻す方法 通常は,PCからカメラの内蔵メモリへデータを書き込むことはできない設定になっています。 基板交換後などに,内蔵メモリへデータを書き戻す場合には,この設定を一時的に変更する必要があります。 設定の変更は,Adjust StationからAdjust Manualを起動させて書き込み許可ツール(WriteEnableTool)を使用します。 書き戻し方法 Adjust StationからAdjust Manualを起動する。 (WriteEnableTool)ボタンをクリックする。 Activate Write Enable Mode ボタンをクリックする。 設定の変更が終了すると,次のメッセージが表示されますので OK ボタンをクリックする。 ドライバを元に戻して、カメラとPCをマスストレージ接続する。 PCに読み出しておいたデータをカメラの内蔵メモリに書き込む。 カメラとPCの接続を解除し,カメラの電源をOFFにする。 注意: カメラの電源をOFFにすることにより,書き込み許可の設定が解除されます。 DSC-T900_L2...
Page 14
ENGLISH JAPANESE ENGLISH JAPANESE 1-5. 自己診断機能 1-5-2. 自己診断表示 1-5-1. 自己診断機能について 本機の動作に不具合が生じたとき,LCD画面にアルファベッ 本機の動作に不具合が生じたとき,自己診断機能が働き, トと4桁の数字が表示され,3.2Hzで点滅します。この5文字 L C D 画面に,どう処置したらよいか判断できる表示を行い の表示によって対応者分類および不具合の生じたブロックの ます。自己診断機能については取扱説明書にも掲載されて 分類,不具合の詳細コードを示します。 います。 LCD画面 C : 3 2 : 00 3.2Hz点滅 対応者分類 詳細コード ブロック分類 C :お客さま自身で対応 対応方法の違いにより分類 「1-5 -3 . 自己診断コード表」 例 13 ・・・“メモリースティック を参照...
2. DISASSEMBLY NOTE FOR REPAIR • Make sure that the flat cable and flexible board are not cracked of bent at the terminal. Cut and remove the part of gilt Do not insert the cable insufficiently nor crookedly. which comes off at the point. (Be careful or some •...
Page 19
HELP HELP 2-2. DISASSEMBLY EXPLODED VIEW HARDWARE LIST 2-2-1. OVERALL SECTION Follow the disassembly in the numerical order given. (1-1 to 1-8) Front Block (2-1 to 2-2) Lens Block Note: High-voltage cautions Discharging the Capacitor Short-circuit between the two points with the short jig about 10 seconds.
Page 20
2-2-2. REAR SECTION EXPLODED VIEW HARDWARE LIST Follow the disassembly in the numerical order given. (1-1 to 1-4) Cabinet (Rear) Block (2-1 to 2-4) LCD Block 1 Cabinet (Rear) Block Note: 1-4E When the adhesive power is down, (Claws) replace it with new one. (Claws) HELP02 (Peel off)
2-2-3. MAIN SECTION EXPLODED VIEW HARDWARE LIST Follow the disassembly in the numerical order given. (1-1 to 1-5) RL-088 Flexible Board (2-1 to 2-6) SY-225 Board (3-1 to 3-4) ST-216 Flexible Board (Claws) 1-5E 1 RL-088 Flexible Board (Claws) (Peel off) 3-4E HELP10 2 SY-225 Board...
Page 22
HELP Sheet attachment positions and procedures of processing the flexible boards/harnesses are shown. HELP01 PRECAUTION INSTALLING LENS BLOCK Lens Block CD-761 Flexible Board Tripod Screw Main Flame Insert CD-761 Flexible Board between Main Frame and Tripod Screw. HELP02 HOW TO FOLD FLEXIBLE BOARDS AND SHEET (P) PUTTING POSITION Fold Flexible Board to arrow direction.
Page 23
HELP03 SHEET (P) PUTTING POSITION Cabinet (Rear) Assy Sheet (P) When the adhesive power is down, replace it with new one. Bosses Wall surface end HELP04 GROUND SHEET (H) PUTTING POSITION Ground Sheet (H) Cabinet (Rear) Assy Wall surface Wall surface end HELP05 LIGHT INTERCEPTION SHEET (L) PUTTING POSITION...
Page 24
HELP06 HELP07 LIGHT INTERCEPTION SHEET (L) SHEET (CCD-A) AND LIGHT INTERCEPTION PUTTING POSITION SHEET (L) PUTTING POSITION LCD Flexible Board (LCD panel) Edge of LCD Flexible LCD Flexible Board Board (LCD Backlight) (LCD Backlight) Light Interception Sheet (L) Sheet (CCD-A) Width of Multi Fixed Plate Edge of Multi Fixed Plate...
Page 25
HELP09 ST LIGHT INTERCEPTION SHEET AND AF CUSHION PUTTING POSITION AND HOW TO FOLD ST-216 FLEXIBLE BOARD ST Light Interception Sheet ST-216 Flexible Board Edge of ST-216 Flexible Board ST-216 Flexible Board AF Cushion Edge of ST-216 Flexible Board Mountain fold ST-216 Flexible Board Mountain fold DSC-T900_L2...
Page 26
HELP10 GASKET (BL) PUTTING POSITION Dented part Wall surface end Main Flame Gasket (BL) DSC-T900_L2 HELP...
3. BLOCK DIAGRAMS Link Link OVERALL BLOCK DIAGRAM (1/2) POWER BLOCK DIAGRAM (1/2) OVERALL BLOCK DIAGRAM (2/2) POWER BLOCK DIAGRAM (2/2) DSC-T900_L2...
Page 28
3. BLOCK DIAGRAMS 3-1. OVERALL BLOCK DIAGRAM (1/2) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located. CD-761 FLEXIBLE BOARD SY-225 BOARD (1/2) LCD901 (1/2) LENS BLOCK (LCD MODULE) CN705 CN302 LENS...
Page 29
3-2. OVERALL BLOCK DIAGRAM (2/2) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located. RL-088 FLEXIBLE BOARD SY-225 BOARD (2/2) CN704 (2/2) CN702 S002 XPWR_ON XPWR_ON ACV_UNREG ON/OFF SE001 (SHUTTER DOOR DETECT) Q001, D001...
Page 30
3-3. POWER BLOCK DIAGRAM (1/2) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located. SY-225 BOARD (1/2) F002 ST_UNREG CN703 MS_VCC MEMORY Q009 R004 BATT_UNREG STICK SWITCH CN704 PRO DUO F001 ACV_UNREG IC001...
Page 31
3-4. POWER BLOCK DIAGRAM (2/2) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located. SY-225 BOARD (2/2) LCD901 (LCD MODULE) CN705 D_1.85V D_1.85V D_1.85V XDD_SYS_RST XDD_SYS_RST 3.5 INCH COLOR L701 D_3.1V XAF_LED...
ENGLISH JAPANESE 4-2. SCHEMATIC DIAGRAMS ENGLISH JAPANESE 4-2. SCHEMATIC DIAGRAMS 4-2. SCHEMATIC DIAGRAMS (ENGLISH) THIS NOTE IS COMMON FOR SCHEMATIC DIAGRAMS (In addition to this, the necessary note is printed in each block) (For schematic diagrams) 1. Connection • All capacitors are in µF unless otherwise noted. pF : µ Pattern box µF.
Page 35
ENGLISH JAPANESE 4-2. SCHEMATIC DIAGRAMS ENGLISH JAPANESE 4-2. SCHEMATIC DIAGRAMS (JAPANESE) 回路図共通ノート (他に必要なノートは各ブロックに記載してあります) 【回路図ノート】 1. 接続図 ・ケミコン,タンタルを除くコンデンサで,耐圧50V以下のもの パターンボックス カラーバーチャート はその耐圧を省略。単位はすべてμF(pはpF)。 For PTB-450: Pattern box PTB-450 ・チップ抵抗で指示のないものは,1/10W以下。 J-6020-250-A J-6082-200-A kΩ=1000Ω,MΩ=1000kΩ ・チップ部品交換時の注意 For PTB-1450: Small pattern box J-6082-559-A PTB-1450 取り外した部品は再使用せず,未使用の部品をご使用くださ J-6082-557-A い。 タンタルコンデンサのマイナス側は熱に弱いため注意してくだ...
Page 36
Schematic diagrams of the CD-761 flexible board and SY-225 board are not shown. Pages from 4-4 to 4-14 are not shown. DSC-T900_L2...
Page 37
• Refer to page 4-2 (English), 4-3 (Japanese) for mark 0. ( L A N D S F O R D I S C H A R G E ) L N D 0 2 4 L N D 0 2 7 N o t e : B T 9 0 0 i s n o t i n c l u d e d i n S T - 2 1 6 f l e x i b l e c o m p l e t e b o a r d .
Page 38
• Refer to page 4-2 (English), 4-3 (Japanese) for mark 0. D 0 0 1 S M L - 4 1 2 M W T 8 6 R 0 0 3 P i n ( P O W E R ) 3 3 0 S003 L N D 0 0 1...
4-3. PRINTED WIRING BOARDS 4-3. PRINTED WIRING BOARDS 4-3. PRINTED WIRING BOARDS (ENGLISH) THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS • : Uses unleaded solder. • Chip parts. • : Circuit board Transistor Diode : Flexible board Pattern from the side which enables seeing. : pattern of the rear side (The other layers’...
Page 41
Printed wiring boards of the CD-761 flexible board and SY-225 board are not shown. Pages from 4-18 to 4-20 are not shown. DSC-T900_L2...
Page 42
ST-216 (2 layers) : Uses unleaded solder. CAUTION Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. Dispose of used batteries according to the instructions. 注意 電池の交換は,正しく行わないと破裂する恐れがあります。 電池を交換する場合には必ず同じ型名の電池又は同等品と交換してください。 使用済み電池は,取扱指示に従って処分してください。 ST-216 FLEXIBLE BOARD LANDS DISCHARGE LND024 LND027...
Page 43
RL-088 (1 layer), BT-052 (1 layers) : Uses unleaded solder. RL-088 FLEXIBLE BOARD S003 S004 (ZOOM) (PLAYBACK) S001 (SHUTTER) R 0 0 3 S005 Note: SP901 is not included in D001 (MODE SWITCH) (POWER) RL-088 flexible complete board. (MOVIE) S002 (CAMERA) ON/OFF SP901...
NOTE NOTE 5. REPAIR PARTS LIST NOTE: Characters A to Z of the electrical parts list indicate location of exploded views in which the desired part is shown. EXPLODED VIEWS EXPLODED VIEWS Link Link OVERALL SECTION REAR SECTION MAIN SECTION ELECTRICAL PARTS LIST ELECTRICAL PARTS LIST Link...
Page 45
5. REPAIR PARTS LIST 5. REPAIR PARTS LIST 5. REPAIR PARTS LIST (ENGLISH) When indicating parts by reference number, NOTE: please include the board name. • -XX, -X mean standardized parts, so they may have some differences from the original one. The components identified by mark 0 or •...
5. REPAIR PARTS LIST 5. REPAIR PARTS LIST 5-1. EXPLODED VIEWS DISASSEMBLY HARDWARE LIST 5-1-1. OVERALL SECTION Rear section (See page 5-3) #160 #161 (Note 2) #160 #161 (Note 2) #160 #161 (Note 2) (including IC001(CCD imager) and CD-761 flexible complete board) (Note 1) Note 2 : Please refer to “THE COMBINATION OF CABINET’S COLOR AND SCREW”...
5. REPAIR PARTS LIST 5. REPAIR PARTS LIST DISASSEMBLY HARDWARE LIST 5-1-2. REAR SECTION LCD901 Main section (See page 5-4) #160 #161 (Note) Note : Please refer to “THE COMBINATION OF CABINET’S COLOR AND SCREW” on page 5-1 about the combination cabinet’s color and screw.
Page 48
5. REPAIR PARTS LIST 5. REPAIR PARTS LIST DISASSEMBLY HARDWARE LIST 5-1-3. MAIN SECTION ns: not supplied SP901 BT901 - 2 2 CAUTION Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. Dispose of used batteries according to the instructions.
Page 49
BT-052 5-2. ELECTRICAL PARTS LIST Ref. No. Part No. Description Ref. No. Part No. Description 1-878-191-11 BT-052 FLEXIBLE BOARD ******************** (BT901 is not included in BT-052 flexible board.) < BATTERY TERMINAL BOARD > 0 BT901 1-780-651-11 TERMINAL BOARD, BATTERY ************************************************************ Electrical parts list of the CD-761 flexible board is not shown.
Page 50
RL-088 ST-216 Ref. No. Part No. Description Ref. No. Part No. Description A-1707-166-A RL-088 FLEXIBLE BOARD, COMPLETE < RESISTOR > ****************************** (SP901 is not included in RL-088 flexible complete board.) R003 1-216-121-11 METAL CHIP 1/10W R004 1-218-989-11 METAL CHIP 1/16W <...
Page 51
Ver. 1.1 2009.07 The changed portions from Ver. 1.0 are shown in blue. Checking supplied accessories. Battery charger Battery charger USB Cable Conversion (2P) Adaptor 0 1-569-008-12 (BC-CSD) (BC-CSD) 1-829-868-41 0 1-480-352-12 (J) 0 1-480-352-32 (E (Except Middle East)) 0 1-480-352-22 (US, CND) (EXCEPT US, CND, J) Rechargeable battery pack Conversion (2P) Adaptor...
Page 52
HARDWARE LIST (1/9) #1: M1.7 X 2.5 #2: M1.7 X 4.0 #3: M1.7 X 2.5 #4: M1.4 X 2.5 (Tapping) (Black) (Black) (Red) (Dark Silver) 2-635-562-11 2-635-562-31 2-660-401-01 3-348-998-81 #5: M1.7 X 3.5 (Tapping) #6: M1.4 X 1.7 #7: M1.7 X 1.6 #8: M1.7 X 3.5 (Tapping) (Black) (Silver)
Page 53
HARDWARE LIST (2/9) #21: M1.4 X 3.0 #22: M1.7 X 5.0 (Tapping) #23: M1.7 X 4.0 (Tapping) #24: B1.7 X 5.5 (Tapping) (Black) (Silver) (Black) (Black) 2-662-396-21 3-083-261-01 3-080-204-11 4-679-805-11 #25: M1.7 X 3.0 #26: M1.4 X 2.0 #27: M1.4 X 2.0 #28: M1.4 X 4.0 (Tapping) (Black) (Silver)
Page 54
HARDWARE LIST (3/9) #41: M3.0 X 8.0 (Tapping) #42: M2.0 X 4.0 (Tapping) #43: M1.7 X 4.0 #44: M1.7 X 3.0 (Tapping) (Silver) (Silver) (Red) (Silver) 3-065-748-01 7-628-253-00 2-660-401-31 3-078-890-61 #45: M1.4 X 2.5 #46: M1.7 X 3.0 #47: M1.4 X 3.0 (Tapping) #48: M1.7 X 2.5 (Silver) (Red)
Page 55
HARDWARE LIST (4/9) #64: M1.7 X 5.0 (Tapping) #61: M3.0 X 10.0 #62: M2.0 X 3.0 #63: M5.0 X 12.5 (Silver) (Black) (Silver) (Black) 2-666-551-21 7-682-549-09 3-080-202-21 3-060-811-21 12.5 10.0 #65: M1.4 X 3.5 #66: M1.4 X 1.4 #67: M1.4 X 2.0 #68: M1.7 X 4.0 (Silver) (Silver)
Page 56
HARDWARE LIST (5/9) #81: M1.7 X 2.5 #82: M1.4 X 1.4 #83: M1.7 X 7.0 (Tapping) #84: M2.0 X 3.0 (Silver) (Silver) (Black) (Silver) 2-515-756-01 3-272-251-01 3-080-204-41 3-072-453-11 #85: M1.7 X 2.5 #86: M1.7 X 4.0 (Tapping) #87: M1.6 X 5.3 #88: M1.6 X 5.9 (Tapping) (Black) (Silver)
Page 57
HARDWARE LIST (6/9) #101: M2.0 X 5.0 #102: M2.6 X 8.0 #103: M2.6 X 10.0 #104: M3.0 X 8.0 (Silver) (Black) (Silver) (Black) 7-621-555-39 7-621-284-30 7-685-794-09 7-682-548-09 10.0 #105: M2.0 X 4.0 #106: M2.0 X 6.0 #107: M2.0 X 5.0 #108: M1.7 X 3.0 (Tapping) (Red) (Black)
Page 58
HARDWARE LIST (7/9) #121: M2.0 X 4.0 (Tapping) #122: M3.0 X 6.0 #123: M4.0 X 8.0 #124: M1.7 X 2.0 (Silver) (Black) (Black) (Silver) 7-682-547-09 3-080-205-11 7-682-561-09 2-599-475-01 #125: M1.4 X 3.0 #126: M2.9 X 3.5 #127: M3.0 X 25.0 #128: M4.0 X 12.0 (Black)
Page 59
HARDWARE LIST (8/9) #141: M2.6 X 5.0 (Tapping) #142: M1.4 X 2.0 #143: M1.4 X 2.0 #144: M1.4 X 1.2 (Silver) (Silver) (Black) (Silver) 4-111-392-01 4-111-392-11 4-111-392-21 7-685-791-01 #145: M1.4 X 2.4 #146: M1.4 X 2.4 #148: M1.7 X 3.0 #147: M1.4 X 3.5 (Silver) (Black)
Page 60
HARDWARE LIST (9/9) #161: M1.4 X 3.0 (Black) 4-139-852-01...
Page 64
: Points changed portion & : Points added portion Before Change After Change Page 2 SY-225 Board 2 SY-225 Board Note: Be sure not to give a load. - 2 2 - 2 2 HELP08 HELP08 2 6E 2 6E Before Change LIGHT INTERCEPTION SHEET (L) PUTTING POSITION HELP05...
Page 65
• Change of Exploded Views REPAIR PARTS LIST : Points changed portion 5-1. EXPLODED VIEWS & : Points added portion Before Change Page 5-1-2. REAR SECTION Main section Ref. No. Part No. Description After Change 5-1-2. REAR SECTION Main section Ref.
Page 66
: Points changed portion Before Change After Change Page 5-1-3. MAIN SECTION 5-1-3. MAIN SECTION Ref. No. Part No. Description Ref. No. Part No. Description X-2345-634-1 BTH-ASSY (SILVER) (SILVER) X-2345-634-2 BTH-ASSY (SILVER) (SILVER) X-2345-799-1 BTH-ASSY (BROWN) (BRONZE BROWN) X-2345-799-2 BTH-ASSY (BROWN) (BRONZE BROWN) X-2345-800-1 BTH-ASSY (RED) (RED) X-2345-800-2 BTH-ASSY (RED) (RED) X-2345-801-1 BTH-ASSY (BLACK) (BLACK)
Page 67
Reverse 985267832.pdf Revision History S.M. Rev. Ver. Date History Contents issued 2009.02 Official Release — — 2009.07 Supplement-1 • Change of Disassembly and HELP05 (S1 09-143) • Addition of HELP11 • Change of Exploded Views • Revision of Supplied Accessories S.