Agp-v2740 series 3d multimedia accelerator (24 pages)
Summary of Contents for Asus AAEON UP Xtreme i12
Page 1
UP Xtreme i12 Maker Board UPX-ADLP01 User’s Manual 1st Ed Last Updated: October 24, 2022...
Page 2
Copyright Notice This document is copyrighted, 2022. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of the original manufacturer.
Page 3
Acknowledgement All other products’ name or trademarks are properties of their respective owners. Microsoft®, Windows® are registered trademarks of Microsoft Corp. ⚫ Intel®, Pentium®, Iris® and Celeron® are registered trademarks of Intel ⚫ Corporation Debian is a registered trademark of Software in the Public Interest, Inc. ⚫...
Page 4
Packing List Before setting up your product, please make sure the following items have been shipped: Item Quantity UPX-ADLP01 (UP Xtreme i12) with heatsink ⚫ If any of these items are missing or damaged, please contact your distributor or sales representative immediately.
Page 5
About this Document This User’s Manual contains all the essential information, such as detailed descriptions and explanations on the product’s hardware and software features (if any), its specifications, dimensions, jumper/connector settings/definitions, and driver installation instructions (if any), to facilitate users in setting up their product. Users may refer to the product page at AAEON.com for the latest version of this document.
Page 6
Safety Precautions Please read the following safety instructions carefully. It is advised that you keep this manual for future references All cautions and warnings on the device should be noted. Make sure the power source matches the power rating of the device. Position the power cord so that people cannot step on it.
Page 7
If any of the following situations arises, please the contact our service personnel: Damaged power cord or plug Liquid intrusion to the device iii. Exposure to moisture Device is not working as expected or in a manner as described in this manual The device is dropped or damaged Any obvious signs of damage displayed on the device...
Page 8
FCC Statement This device complies with Part 15 FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received including interference that may cause undesired operation.
Page 10
China RoHS Requirement (EN) Poisonous or Hazardous Substances or Elements in Products AAEON Main Board/ Daughter Board/ Backplane Poisonous or Hazardous Substances or Elements Hexavalent Polybrominated Polybrominated Component Lead Mercury Cadmium Chromium Biphenyls Diphenyl Ethers (Pb) (Hg) (Cd) (Cr(VI)) (PBB) (PBDE) PCB &...
Specifications System Processor 12th Gen Intel® Core™ Processor SoC Core i7-1270PE Core i5-1250PE Core i3-1220PE Celeron® 7305E Graphics Intel® Iris® Xe graphics Memory Up to 32GB on board LPDDR5 4800MHz (Dual Channel) Storage M.2 2280 M-Key x 2 (PCIe Gen 4.0 x4) SATA III x 1 10-pin USB 2.0 x 2 / HSUART x 1 4-pin Fan Connector x 1...
Page 15
System Expansion 40-pin GPIO x 1 M.2 2230 E-Key x 1 M.2 2280 M-Key x 2 (PCIe Gen 4.0 x4) SATA III x 1 M.2 3052 B-Key x 1 Micro SIM Slot x 1 Display Interface HDMI 2.0b x 1 DP 1.4a x 1 DP 1.4b via USB Type C x 1 eDP 1.4b x 1...
Page 16
Mechanical Dimension 4.73” x 4.82” (120.35mm x 122.5mm) Net Weight 0.85 lb. (0.39 Kg) Gross Weight 1.33 lb. (0.6 Kg) Environment Operating Temperature With Heatsink: 32°F ~ 140°F (0°C ~ 60°) / 0.5 airflow Operating Humidity 0% ~ 90% relative humidity, non-condensing MTBF (Hours) 362,068 Certification...
List of Jumpers and Connectors Please refer to the table below for all of the board’s jumpers and connectors that you can configure for your application Label Function PWR button HDMI/DP SATA Power SATA Connector USB Type A Dual Port USB Type A DUAL PORT USB Type C...
Label Function CN19 CPLD and OS update CN20 CSI Port Front Panel CN21 1x6P Wafer CN22 DC Power Jack CN23 DC terminal block Fan connector 2.3.1 Power Button (SW1) Signal Signal PWR_SW# PWR_SW# SW1_LED_P SW1_LED_N Chapter 2 – Hardware Information...
2.3.5 SATA Power (CN4) Signal Signal 2.3.6 SATA Connector (CN5) Signal Signal SATA_TXP0 SATA_TXN0 SATA_RXN0 SATA_RXP0 Chapter 2 – Hardware Information...
2.3.7 USB Type A Dual Port (CN6) Signal Signal USB2_D1- USB2_D1+ USB3_RX1- USB3_RX1+ USB3_TX1- USB3_TX1+ USB2_D2- USB2_D2+ Chapter 2 – Hardware Information...
2.3.8 USB Type A Dual Port (CN7) Signal Signal USB2_D3- USB2_D3+ USB3_RX3- USB3_RX3+ USB3_TX3- USB3_TX3+ USB2_D4- USB2_D4+ USB3_RX4- USB3_RX4+ USB3_TX4- USB3_TX4+ Chapter 2 – Hardware Information...
2.3.25 Fan Connector (J1) Signal Signal TACH 2.3.26 AT/ATX Mode (JP1) Signal Signal ATX_MODE PWRBTN AT_MODE ATX Mode (Default) AT Mode Chapter 2 – Hardware Information...
Linux Setup The UP Xtreme i12 supports Linux operating systems (see Chapter 1 for specifications). For instructions on how to install a Linux OS onto your UP Xtreme i12, you can find several guides and tutorials in the wiki section of the UP Board website at https://up-board.org for both installing supported distributions as well as porting your own Linux build.
Dummy Driver Information 3.3.1 Dummy Driver Installation The following instructions detail how to install the dummy driver for your UP Xtreme i12 (UPX-ADLP01). Step 1 – Download UPNullDrv.msi. Step 2 – Click UPNullDrv.msi and follow the steps as per the below images to install Driver.
Page 51
Once you have successfully installed the dummy driver, you will be able to locate it via your system’s Device Manager, as shown below. Chapter 3 – Software Installation...
Introduction This section provides instructions for the installation of the UP Framework SDK. Instructions are provided for Windows 10 and Windows IoT Core. You can download the latest version of UP Framework SDK from the UP community: https://downloads.up-community.org/download/up-sdk-for-windows-10-and-windows-iot/ A.2 Installation for Windows 10 Step 1 Locate the downloaded file UpFrameworkSetup.msi and run the installer.
Page 55
Step 2 Select the installation folder. Default destination path is C:\Program Files(x86)\AAEON\ You may also choose to install the UP Framework SDK for all users or only the current user. Press “Next” to continue installation. Step 3 Press “Next” to confirm the installation. Appendix A –...
Page 56
Step 4 Press “Close” to exit once setup is complete. Appendix A – UP Framework SDK Installation...
A.3 Installation for Windows IoT Core Before you begin, make sure you have downloaded and installed the latest version of the Windows IoT Core image from the UP community. Installation requires using a connected PC with the UP Framework SDK software downloaded and saved.
Page 58
Step 2: Download the UP Framework SDK to your PC and unzip the files. Open PowerShell as an Administrator. Enter the command RemoteInstallation.ps1 to install the UP Framework SDK on the UP IoT Core device. Enter the IP address of the UP IoT Core device when prompted. Note: You must connect Up IoT Core and PC in the same network.
Cables and Connectors This table provides detailed information about the cables and connectors used by the UP Xtreme i12 (UPX-ADLP01). If you have any questions about the configuration of your board, please contact your AAEON sales representative. Mating Label Connector PN Description Mating Cable Description Cable PN...
Page 61
Mating Label Connector PN Description Mating Cable Description Cable PN CN13 165420753A M.2 Key-B Slot CN14 16528X0015 GbE RJ-45 x2 Audio Jack(Line out CN15 1652708203 + Mic in) COM Port.9P .COM Cable to Wafer Box.10P . COM CN16 1655901000 170X000255 VGA.210mm.FLYINGWAY.FW port AA-1375.