Table of Contents
Advertisement
●
Place the disc with its printed side upward and gently put it on the tray.
●
Do not scratch the disc or write anything directly on it with a pencil or ball-point pen.
Keep the disc away from cigarette smoke.
●
●
Do not leave the disc in a high-temperature place (e.g., place exposed to direct sunlight or close to a heater).
●
When dust or fingerprints are attached on the disc, wipe the disc from its center to edge with a dry soft cloth slowly and gently.
●
Use the CD cleaner to clean the disc. Do not use record spray/cleaner, benzene, or thinner.
Keep the disc in a disc case when not in use.
●
●
If the disc emits large noise in the optical disk drive, remove the disc and insert it back again.
Writing Data onto Disc
After writing the data onto disc, be sure to perform data compare process.
●
●
An operator should always be concerned with data writing (unattended writing should not be performed).
Do not use a cellular phone or pager around this product.
Turn off the cellular phone or pager. Radio interference may cause malfunctions this product.
●
Handling of Optical Disk Drive.
Do not leave the tray ejected from the optical disk drive.
●
Do not leave the drive with an optical disc being contained.
●
●
Clean the disc and drive in regular basis. Be careful not to touch the lens while cleaning the drive.
●
Make sure that the drive works normally by reading a disc such as NEC EXPRESSBUILDER.
About Write Error.
A write error might occur when writing a data by using the optical disk drive due to the operating environment or characteristics of disc, etc..
●
If a write error occurs even after the cleaning, try another disc.
Before Writing onto Disc.
●
It is prohibited by the law to reproduce audio CD and the application without the permission of the writer except for the personal use.
●
The data stored in DVD-R, DVD+R, or CD-R may be destroyed partially or entirely due to write error. To prevent the data loss, observe the
following instructions.
-
Quit the program including an application software that might consume a large amount of memory.
-
Disable the screen saver utility.
-
Quit the program to check the disc such as virus checker or system agency.
-
Disable the utility that might start during writing, such as scheduler or timer.
-
Disable the power-saving feature in power management.
-
Do not boot any application while writing.
Writing/Reading Time Fluctuation.
●
The optical disk drive has a feature to detect the disc condition and determine the optimum writing or reading speed for the disc.
Accordingly, the time required for writing or reading data may not be constant, depending on disc condition.
Compensation for Saved Data.
●
NEC is not liable for data saved in optical disc and will not provide compensation if such data is lost.
- 15 -
Anti-Static Measures
Installing or Uninstalling an Internal Optional Device
1. Notes before carrying out the work
(1) To avoid electric hazard and malfunction, be sure to turn off the Power switch of this product and unplug the power cord from an outlet
before carrying out the work. However, there is no need to do this if the internal optional device is hot-swappable.
(2) This internal optional device consists of static-sensitive electronic components. To avoid failures caused by static electricity when
installing or uninstalling the internal optional device, wear an anti-static wrist strap on your wrist and provide earthing before carrying
out the work. And also connect a wrist strap to earth ground when you wear a wrist strap.
(3) Handling of cables When connecting a cable (e.g., LAN cable), static electricity may also be charged due to friction against the floor.
Connecting a charged cable with an I/O device may cause damage to the devices. It is recommended to discharge static electricity
before connecting a cable by using neutralization apparatus and so on.
Be sure to read this before replacing an optical disk drive.
1. Before replacement
Before replacing an optical disk drive, check and make a note of the drive letter (*) of the optical disk drive.
The drive letter may be changed after the replacement.
*The drive letter is an alphabetical letter that is assigned to each drive in Windows.
2. Drive letter change
If the drive letter is changed due to the replacement of an optical disk drive, the letter could be restored to the one recorded in step 1
by following the steps below.
2-1. Start Windows, and log in as an administrator.
2-2. Point to [Administrative Tools], open [Computer Management], and select [Disk Management].
2-3. Right-click on a drive for the optical disk, and select [Change Drive Letter and Paths].
2-4. Change back the drive letter.
4. Specifications
Compatible interface
SATA
Data transfer mode
1.5Gbits/sec
Outside dimensions
130 (width)ｘ132 (depth)ｘ9.5 (height) mm
Weight
0.2kg or less
Power supply (rating)
DC+5V
Temperature: 5 to 35/45℃
Operating environment
(It depends on environmental condition of a server.)
(during operation)
Humidity: 10 to 80% (no condensation)
This product utilizes a laser.
CAUTION : Use of control, adjustment or performance of procedures other than those
specified herein may result in hazardous radiation exposure.
Do not open covers and do not repair yourself. Refer servicing to qualified personnel.
.
Este producto utiliza un láser.
PRECAUCIÓN:Si se realiza un ajuste que pueda afectar el nivel de potencia de la emisión láser,
no toque ni ajuste sin la autorización del personal de servicio.
De lo contrario pueden producirse emisiones dañinas de láser a las que quedaría expuesto.
Ce produit utilise un laser.
ATTENTION:Si un ajustement est nécessaire, seul le personnel de service est autorisé à contrôler
le niveau d'émission laser. Si vous tentez de le faire vous même, vous risquez de vous
exposer a des émissions laser dangereuses.
- 16 -
Advertisement
Table of Contents
