Philips 43PUH6101/88 Service Manual page 29

Picture mode Screen size
Cool (11000K) 43PUH6101/88 118
43PUS6101/12 117
43PUT6101/12 116
43PUT6101/60 118
43PUS6201/12 125
43PUT6201/12 123
49PUH6101/88 120
49PUS6101/12 118
49PUT6101/12 118
49PUT6101/60 119
55PUH6101/88 122
55PUS6101/12 123
55PUT6101/12 123
55PUT6101/60 122
55PUS6201/12 122
55PUT6201/12 124
65PUS6121/12 121
65PUT6121/12 121
Warm (6500K) 43PUH6101/88 126
43PUS6101/12 125
43PUT6101/12 127
43PUT6101/60 126
43PUS6201/12 127
43PUT6201/12 126
49PUH6101/88 127
49PUS6101/12 125
49PUT6101/12 124
49PUT6101/60 123
55PUH6101/88 127
55PUS6101/12 125
55PUT6101/12 127
55PUT6101/60 126
55PUS6201/12 121
55PUT6201/12 122
65PUS6121/12 127
65PUT6121/12 126
This group setting of colour temperature will be applied
automatically to the TV / VGA / HDMI / AV sources.
Note: The information of the RGB value is only for reference,
the specific value is based on model adjustment.
6.4 Option Settings
6.4.1 Introduction
The microprocessor communicates with a large number of I
ICs in the set. To ensure good communication and to make
digital diagnosis possible, the microprocessor has to know
which ICs to address. The presence / absence of these
MT5561 ICs is made known by the option codes.
Notes:
• After changing the option(s), save them by pressing the OK
button on the RC before the cursor is moved to the left,
select STORE and press OK on the RC.
• The new option setting is only active after the TV is
switched "off" / "stand-by" and "on" again with the mains
switch (the NVM is then read again).
6.4.2 Option Code Overview
Enter SAM mode to check the option codes. they could be
edited in the NVM.
6.4.3 Display Code Overview
Press the following key sequence on a standard RC
transmitter: "062598" directly followed by MENU and "xxx",
where "xxx" is a 3 digit decimal value of the panel type: see
Colour temperature
Red Green Blue
123 128
122 127
123 125
124 126
127 126
125 126
127 121
126 121
125 123
125 122
117 127
115 126
116 125
117 124
118 124
119 126
122 127
121 127
112 77
113 78
113 79
112 80
114 88
113 87
75 70
77 69
76 68
78 71
90 81
91 80
92 82
93 82
95 88
96 89
116 98
115 97
2
C
Alignments
column "Display Code" in
the Display Code, restart the set immediately.
Table 6-3 Display code overview
CTN_ALT BOM#
43PUH6101/88
43PUS6101/12
43PUT6101/12
43PUT6101/60
43PUS6201/12
43PUT6201/12
49PUH6101/88
49PUS6101/12
49PUT6101/12
49PUT6101/60
55PUH6101/88
55PUS6101/12
55PUT6101/12
55PUT6101/60
55PUS6201/12
55PUT6201/12
65PUS6121/12
65PUT6121/12
6.5 Reset of Repaired SSB
A very important issue towards a repaired SSB from a Service
repair shop (SSB repair on component level) implies the reset
of the NVM on the SSB.
A repaired SSB in Service should get the service Set type
"00PF0000000000" and Production code "00000000000000".
Also the virgin bit is to be set. To set all this, you can use the
"NVM editor" and "Dealer options" items in SAM (do not forget
to "store").
After a repaired SSB has been mounted in the set (set repair
on board level), the type number (CTN) and production code of
the TV has to be set according to the type plate of the set. For
this, you can use the NVM editor in SAM.
In case of a display replacement, reset the "Operation hours
display" to "0", or to the operation hours of the replacement
display.
Remark:
- After the NVM has been replaced, go to SAM and scroll to the
<Reload MAC address> (see figure 1*).
- Select the item and press <OK> on the RC.
6.5.1 Reset of Repaired SSB
Instruction
After NVM replacement, reload MAC address via SAM
menu.This ensures the correct MAC address to be available in
CSM for future repair actions.
Way of working:
• After the NVM has been replaced, go to SAM and scroll to
the <Reload MAC address> .
• Select the item and press <OK> on the RC.
Notes:
• Only applicable to all related models that are "Smart TV
level 0"enabled (only YouTube access). For models
without internet connection feature, no action is needed.
• HDCP keys are located in the NVM.
New NVM EEPROMs are shipped with pre-loaded HDCP keys.
6.5.2 SSB Identification
SSB's of this chassis are identified by a "715" code on the SSB.
back to
div.table
TPL16.1E LA 6.
back to div.table 6-3. After resetting
Panel Type
TPT430U3-EQYSHM.G S1G
TPT430U3-EQYSHM.G S1G
TPT430U3-EQYSHM.G S1G
TPT430U3-EQYSHM.G S1G
TPT430U3-EQYSHM.G S1H
TPT430U3-EQYSHM.G S1H
TPT490U2-EQYSHM.G SC1L
TPT490U2-EQYSHM.G SC1L
TPT490U2-EQYSHM.G SC1L
TPT490U2-EQYSHM.G SC1L
TPT550J1-QUBN0.K S8940D
TPT550J1-QUBN0.K S8940D
TPT550J1-QUBN0.K S8940D
TPT550J1-QUBN0.K S8940D
TPT550J1-QUBN0.K S8940L
TPT550J1-QUBN0.K S8940L
TPT650UA-QVN06.U S600C
TPT650UA-QVN06.U S600C
EN 29
Display Code
213
213
213
213
217
217
214
214
214
214
215
215
215
215
218
218
216
216
2016-Sep-23