Table of Contents
Advertisement
66
GETTING STARTED
Installation
continued
Proceed with the setting instructions described below in order to activate the satellite receiver control functions.
These settings are supported only by the satellite receivers found on the list of compatible satellite receivers ( see page 23).
Satellite Setting
ON/
STANDBY
VTR
TV
CH/TRK
1
2
3
4
5
6
TV VOL
7
8
9
I.SELECT
ENTER
0
F. ADV
INDEX
COUNT/ TR
CLR/ RST
MENU /
REC
TIMER
TXT/ TV
PLAY
SLOW
PAUSE/STILL
OK
CURSOR
REW
F F
STOP
SP/LP
AUDIO
DISPLAY TV/VIDEO
A.DUB
SAT.MONI.
SAT.CONT.
PROG.
PROG.
20
1
Press MENU on the remote control.
Result : The programming menu is displayed.
2
Press the corresponding $, ❷!or
➛, ❿ button to select the
INSTALLATION option.
PROG
OPTIONS
Then press the OK button to select
this option.
BONUS
CLOCK
Result : The INSTALLATION
INSTALLATION
menu is displayed.
$❷!!➛❿
OK
3
Press the $ or ❷ button to select the
SATELLITE SETTING option and
then press the ❿button to select this
INSTALL
AUTO SET UP
option.
MANUAL SET UP
NEXTVIELINK SETTING
SATELLITE SETTING
VCR OUTPUT CH
$❷!!!!!!❿
4
Select SATELLITE INPUT, press
** SATELLITE SETTING **
the ➛ or ❿ button to select input
position where the satellite receiver
SATELLITE INPUT
POSITION CH
is connected.
SAT. BRAND NO
→RF→AV1→AV2→AUX
$❷!!!!!!➛❿
5
Select POSITION CH when RF
has been selected. Press the ➛ or ❿
** SATELLITE SETTING **
button to select position where the
SATELLITE INPUT
POSITION CH
RF OUT of satellite receiver is
SAT. BRAND NO
memorized.
$❷!!!!!!➛❿
6
Press the corresponding $ or ❷
button to select SAT. BRAND
** SATELLITE SETTING **
NO .(see page 23)
SATELLITE INPUT
Result : The first digit of receiver
POSITION CH
SAT. BRAND NO
type number is flashed.
$❷!!!!
0-9
66
GETTING STARTED
Installation
Satellite Setting
7
Press the numeric buttons to set receiver type number.
Result : When you enter the receiver type, the VTR sends a test signal to the satellite receiver to make sure that the
receiver type has been entered correctly. The signal will set the satellite channel to 12. If channel 12 is displayed
on your satellite receiver, it means the receiver type is set correctly. Several types may be allocated to one brand.
Enter one after the other until the channel shows 12.
•
Note :
Before pressing the numeric buttons to set receiver type, you must set the remote controller switch to VTR.
INSTALL
•
First check the list of compatible satellite receivers (see page 23).
•
LANG
It is not possible to control a receiver which is not on the list of compatible satellite receivers.
If no codes work, Press MENU button then select NO SATELLITE CONTROL on SATELLITE CH ORDER menu. Go to step no 10
END:
MENU
** SATELLITE SETTING **
SATELLITE INPUT
POSITION CH
SAT. BRAND NO
TEST CH 12 SENDING
:CH36
$❷!!!!
0-9
END:
MENU
8
You now need to tell the VTR the channel order on your satellite receiver. Most Satellite receivers are preset to either
SKY ANALOGUE, SKY DIGITAL or ON DIGITAL order. If, however, you have changed the order then you will need to select
PERSONAL PREFERENCE and change the VIDEO Plus+ system GUIDE numbers accordingly.
Select any of the SATELLITE CH ORDER and this will customise your VTR to your Satellite receiver.
: RF
: 01
: 017
9
If you select PERSONAL PREFERENCE you will need to select the channel order of the satellite receivers on GUIDE CH menu.
Press FF button to move the active cursor to PR position and select a PR number by using FF or REW button.
Press PLAY or STOP button for other channel orders selection and repeat step 9. Press MENU three times to exit.
MEMORY:
OK
END:
MENU
10
If you selected NO SATELLITE CONTROL you will need to manually select the correct Satellite channel on the receiver when
you want to record a satellite programme.
The set-up is now complete.
: RF
: 01
: 017
How to Preset the Type of Satellite Receiver
MEMORY:
OK
END:
MENU
Note:
The VTR may not be able to control some
types or brands of satellite receiver, due to
: RF
the choice of remote control coding being
: 01
: 017
beyond our control.
Check that the satellite receiver can be
properly controlled.
MEMORY:
OK
Try satellite broadcast timer recording once
END:
MENU
to check that timer recording works properly .
(Refer to page 41).
continued
(continue)
** SATELLITE CH ORDER **
SKY ANALOGUE
: RF
: 01
SKY DIGITAL
ON DIGITAL
: 138
PERSONAL PREFERENCE
NO SATELLITE CONTROL
$❷!!!!
MEMORY:
OK
END:
MENU
END:
MENU
The satellite receiver mode (Power On or Off) must be set before
attempting to perform timer recording.
The procedure to set the mode can be devided into the following 3 types
by satellite receiver. Check which one applies on the attached list before
proceeding.
Preset Type
A
B
C
Please review the compatible satellite receiver list on page 23 before
purchasing a new receiver. In order to assure satellite receiver control,
Satellite Setting must be performed at the installation stage (see page 20).
** GUIDE CH **
GUIDE
PR
101
:
---
102
:
---
103
:
---
104
:
---
105
:
---
$❷!!!!
END:
MENU
Controllable functions
No action needs to be taken. (The satellite
receiver's power may even be OFF.)
Keep the satellite receiver's power OFF.
Keep the satellite receiver's power ON.
21
Advertisement
Table of Contents
