Operation - Bosch SmartphoneGrip BSP3200 Original Operating Instructions

English – 4
Assembly
SmartphoneGrip Assembly (see figure A)
Press and hold the release mechanism (4) to position the
SmartphoneGrip. Place the upper edge of the Smart-
phoneGrip next to the snap-in hook (6) of the display
holder (5) ➊. Pull the SmartphoneGrip towards you and
push the SmartphoneGrip onto the display holder ➋. Let go
of the release mechanism (4).
Press the release mechanism (4) while pulling it towards
you ➊ to remove the SmartphoneGrip. Remove the Smart-
phoneGrip and let go of the release mechanism (4) ➋.
Inserting the Removal Blocker (see figure B)
Insert the removal blocker (12) into the adapter tray (16)
from below until you hear the removal blocker (12) click into
place.
From this point onwards, you can no longer remove the
SmartphoneGrip from the display mount (5) without remov-
ing the display mount (5) from the adapter tray (16) by
loosening the two fastening screws (11).
Note: The removal blocker (12) is not an anti-theft device.
Smartphone Assembly (see figure C)
The SmartphoneGrip can hold smartphones in the following
sizes:
The specified dimensions include any phone cases. Smart-
phones with folio cases must not be used.
The total weight must not exceed 276 g.
Pull the front retaining bracket (1) forwards ➊. Insert your
smartphone (15) with the long side of the phone positioned
against the fixed retaining bracket (2) ➋. Release the front
retaining bracket and place your smartphone (15) in the
centre of the SmartphoneGrip ➌.
Be careful not to pinch your fingers between the movable
u
retaining bracket and the SmartphoneGrip when inserting
your smartphone.
0 275 008 3SG | (25.01.2022)
Once you have inserted your smartphone, check that the
smartphone cannot come into contact with any hard parts on
the bike even in case of vibrations, as this could cause last-
ing damage to the smartphone.
Keypad Lock Assembly (see figure D)
To remove the keypad lock (13), unscrew the securing
screw with a hex key (1.5 mm) (14) ➊ and remove the
keypad lock (13) ➋.
To insert the keypad lock (13), slide the keypad lock (13)
into the provided opening and screw it into place with a hex
key (1.5 mm) (14).
Note: The keypad lock is not an anti-theft device. The
keypad lock prevents the SmartphoneGrip from being
quickly removed from the holder. The keypad lock does not
affect the smartphone in any way
Note: Never leave your smartphone unattended in the
SmartphoneGrip.

Operation

Starting Operation
Place your smartphone in the SmartphoneGrip.
Start the eBike Flow app to have riding data displayed.
Depending on the smartphone's operating sys-
tem, the eBike Flow app can be downloaded
free of charge from the Apple App Store and
the Google Play store.
Use your smartphone to scan the code in order to download
the eBike Flow app.
Charging your Smartphone
While the smartphone is in the SmartphoneGrip, it can be
charged at the same time as displaying riding data. If your
smartphone has an inductive charging function, you can
charge the smartphone without needing a cable.
Inductive Charging
The charging process starts automatically when you place a
smartphone with an inductive charging function in the
SmartphoneGrip. The status LED (9) lights up yellow. When
the smartphone is fully charged, the status LED (9) will light
up green permanently.
The charging voltage is switched off when you remove the
smartphone from the holder.
Charging via USB
If your smartphone does not have an inductive charging
function, you can charge your smartphone via the USB
port (3). To do so, open the USB cap and connect a separate
USB cable (not included in the scope of delivery) to the Mi-
cro-AB USB port.
Pay attention to the type of plug required for your smart-
phone when purchasing the USB cable.
Bosch eBike Systems