Acer Altos BrainSphere P150 F8 User Manual
  1. Manuals
  2. Brands
  3. Acer Manuals
  4. Desktop
  5. Altos BrainSphere P150 F8
  6. User manual

Acer Altos BrainSphere P150 F8 User Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Altos
BrainSphere P150 F8
User Guide

Advertisement

Table of Contents
loading

Related Manuals for Acer Altos BrainSphere P150 F8

Summary of Contents for Acer Altos BrainSphere P150 F8

  • Page 1 Altos BrainSphere P150 F8 User Guide...

  • Page 2: System Setup

    System setup System notes Thank you for purchasing your Altos Workstation. This user guide is intended as a reference for experienced Workstation technicians and helps detail many of the features available in Altos Workstations. For more detailed information about any particular component or software solution, you may consult the technical specifications or the user manual for that application.

  • Page 3: System Component Identification

    System component identification Altos BrainSphere P150 F8 Front configuration: 38L ATX Chassis 編號 說明 USB 3.2 Gen 1 Port x 2 USB 3.2 Gen 1 Port x 2 Audio jacks (Mic In/Out) USB 3.2 Gen2 Port (Type C) Power Button...
  • Page 4 Specification introduction Processor type Intel 12 Core™ i7/i9 series, TDP up to 125W Number of processors On-board Devices Chipset Intel ® Z690 Chipset SATA 4 SATA3 (6 Gb/s) ports SATA RAID Intel onboard software RAID 0, 1, 5, 10 (only supports Windows OS) Intel ®...
  • Page 5 Motherboard Layout...
  • Page 6 I/O Port Introduction...
  • Page 7 Hardware Specifications and Configurations...
  • Page 12 Installing the CPU...
  • Page 15 Installing Memory Modules (DIMM)
  • Page 16 M.2_SSD Module Installation Guide...
  • Page 18 M.2 WiFi/BT Module and Intel® CNVi (Integrated WiFi/BT) Installation Guide...

  • Page 24: Jumper And Connector Information

    Jumper and Connector Information...

  • Page 31: Setting Up The System

    Setting up the system Pre-installation requirements Selecting a site Before unpacking and installing the system, select a suitable site for the system for maximum efficiency. Consider the following factors when choosing a site for the system:  Near a grounded power outlet. ...

  • Page 32: Turning On The System

    Turning on the system After making sure that you have properly set up the system, applied power and connected all the necessary peripherals, you can now power on the system. Follow the procedure below. 。 Press the power button The system starts up and displays a welcome message on the monitor. After that, a series of power-on self-test (POST) messages appears.
  • Page 33 Note: If you have gone through the preceding actions and the system still fails to boot, ask your dealer or a qualified technician for assistance.

  • Page 34: Turning Off The System

    Turning off the system There are two ways to turn off the Workstation—via software or via hardware. The software procedure below applies to a system running on a Windows OS. For other shutdown procedures, refer to the related user documentation. To turn off the system via software: Press <Ctrl>...

  • Page 35: System Troubleshooting

    System troubleshooting...

  • Page 38: Initial System Startup Problems

    Initial system startup problems Problems that occur at initial system startup are usually caused by an incorrect installation or configuration. Hardware failure is a less possible cause. If the problem you are experiencing is with a specific application. Initial troubleshooting checklist ...

  • Page 39: Hardware Diagnostic Testing

    Hardware diagnostic testing This section provides a detailed approach to identifying a hardware problem and its cause. Checking the boot-up status Caution: Before disconnecting any peripheral cables from the Workstation, turn off the system and any peripheral devices. Failure to do so can cause permanent damage to the system and/or the peripheral device.

  • Page 40: Specific Problems And Corrective Actions

    Specific problems and corrective actions Listed below are specific problems that may arise during the use of your Workstation and their possible solutions Confirming loading of the operating system Once the system boots up, the operating system prompt appears on the screen. The prompt varies according to the operating system.
  • Page 41 Optical drive tray cannot be ejected Insert the tip of a paperclip into the small hole on the optical drive. Slowly pull the tray out from the drive until the tray is fully extended. Optical drive cannot read a disc Do the following: ...
  • Page 42  Verify that the software is properly configured for the system.  Refer to the software installation and operation documentation for instructions on setting up and using the software. Try a different version of the software to see if the problem is with the copy you are using.
  • Page 43 Note: If POST does not emit any beep code and characters still do not appear, the display monitor or the video controller may be defective. Contact your local Altos representative or authorized dealer for technical assistance.

  • Page 44: Information For Your Safety And Comfort

    Notices Information for your safety and comfort Safety instructions Read these instructions carefully. Keep this document for future reference. Follow all warnings and instructions marked on the product. Turning the product off before cleaning Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners.
  • Page 45 provided.  Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind onto or into the product. ...
  • Page 46 with the performance of this product.  Use the product only with the supplied power supply cord set. If you need to replace the power cord set, make sure that the new power cord meets the following requirements: detachable type, UL listed/CSA certified, VDE approved or its equivalent, 4.6 meters (15 feet) maximum length.

  • Page 47: Energy Star

    Disposal instructions Do not throw this electronic device into the trash when discarding. To minimize pollution and ensure utmost protection of the global environment, please recycle. ENERGY STAR Altos's ENERGY STAR qualified products save your money by reducing energy cost and protecting the environment without sacrificing features or performance.

  • Page 48: Regulations And Safety Notices

    Regulations and safety notices CLASS 1 LASER PRODUCT CAUTION: INVISIBLE LASER RADIATION WHEN OPEN. AVOID EXPOSURE TO BEAM. Declaration of Conformity for EU countries Hereby, Altos, declares that this system is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.
  • Page 49 List of applicable countries This device must be used in strict accordance with the regulations and constraints in the country of use. For further information, please contact local office in the country of use. Please see http://ec.europa.eu/enterprise/rtte/implem.htm or the latest country list. Note: The following sections are applicable only to Class A systems FCC notice Class A...
  • Page 50 Caution Changes or modifications not expressly approved by the manufacture could void the user’s authority, which is granted by the Federal Communications Commission, to operate this computer. Operation conditions This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Table of Contents