Table of Contents
Advertisement
Quick Links
Z500 Series Z Master Diesel Mowers
Loose Parts
Use the chart below to verify all parts have been shipped.
Step
1
No parts needed
2
No parts needed
3
4
5
No parts needed
6
7
Bulk electrolyte with 1.265 specific gravity
(Purchase from a battery supply outlet.)
8
No parts needed
Number 2 general purpose lithium base or
9
molybdenum base grease. (Purchase
separately.)
10
No parts needed
2004-The Toro Company
8111 Lyndale Ave., Blomington, MN 55420, USA
Description
Printed in the USA
All Rights Reserved
Form No. 3351-414 Rev A
Qty.
-
Adding fuel to the machine
-
Raising the machine up
1
1
1
8
Installing the roll over protection system
8
(ROPS)
8
2
2
2
2
Installing the drive wheels
-
Checking the tire pressure
1
1
Adjusting the motion control levers
4
4
1 US
Activating the battery for international
Gallon
machines only
Charging the battery for international and
-
domestic machines
1 tube
Greasing the bearings
-
Preparing the side discharge chute
Register your product at www.Toro.com
Setup Instructions
Use
Original Instructions (EN)
Advertisement
Table of Contents
Related Manuals for Toro Z Master Z597-D
Summary of Contents for Toro Z Master Z597-D
-
Page 1: Table Of Contents
1 tube Greasing the bearings separately.) No parts needed – Preparing the side discharge chute 2004—The Toro Company Printed in the USA Original Instructions (EN) 8111 Lyndale Ave., Blomington, MN 55420, USA All Rights Reserved Register your product at www.Toro.com... - Page 2 Step Description Qty. No parts needed. – Checking the machine before delivery Operator’s Manual Engine Owner’s Manual Delivering the machine to the customer Parts Catalog Safety video Registration card Step Adding Fuel to the Machine Parts needed for this step: m–7424 None Procedure...
-
Page 3: Roll Bar, Right Section
Step 3. Lightly oil the ends m–7432 of the center roll bar section. 4. Loosely install the center roll bar section, using 2 bolts Installing the Roll Over (1/2 x 3-1/4 inches) and 2 flange nuts (1/2 inch). Protection System (ROPS) Note: Make sure the bolts are installed on the outside of the roll bar. -
Page 4: Wheels
8. Tighten the front m–7406 Step handles against the center roll bar ends. Checking the Tire Pressure Parts needed for this step: None Procedure 1. Check the air pressure in the front and rear tires. Pressure: 13 psi (90 kPa) 2. -
Page 5: Control Lever-Right
Step Adjusting the Motion Control Levers Parts needed for this step: Qty. Part m–6867 Control lever–right (assembled) Control lever–left (assembled) Bolt, 3/8 x 1 inch (assembled) Curved washer, 3/8 inch (assembled) Procedure 1. Check the control levers for the correct alignment. - Page 6 1. Remove the battery. Step Refer to the Operator’s Manual for instructions. Important: Do not add electrolyte while the battery is in the machine. You could spill it, causing corrosion. Activating the Battery for International Machines Only Parts needed for this step: Qty.
- Page 7 Step Step Charging the Battery for Checking the Spindles for International and Domestic Grease Machines Parts needed for this step: Parts needed for this step: Qty. Part None 1 tube Number 2 general purpose lithium base or molybdenum base grease. (Purchase separately.) Procedure Procedure...
- Page 8 3. Grease the fittings on the three spindle bearings. Step Add grease until it comes out of the lower seals. Preparing the Side Discharge Chute Parts needed for this step: None Procedure Remove the plastic tie holding the side discharge chute up and lower the chute into place.
- Page 9 Step Checking the Machine Before Delivery to the Customer Parts needed for this step: None Procedure Before delivering the machine to the customer, ensure that you perform or have performed the procedures listed in the following table and initial each when finished. Refer to the Operator’s Manual for instructions on performing these procedures.
- Page 10 Step Delivering the Machine to the Customer Parts needed for this step: Qty. Part Operator’s Manual Parts Catalog Engine Owner’s Manual Registration card Safety video Procedure At delivery, complete the items listed in the following table and initial each when finished. Model Number: Serial Number:...
- Page 11 Describe the post sale service procedures for your store. Assist the customer in filling out and mailing the registration card or register online at www.Toro.com. Make sure that the customer receives the Operator’s Manual , Parts Catalog , and Engine Owner’s Manual, Set Up Instructions , and safety video.