Toshiba Q9 Series Brochure & Specs page 7

Meets or Exceeds
Your Specifications
Input Voltage
HP Rating 1
Current Rating 4.8
Input Voltage
HP Rating 1
Current Rating 2.1
HP Rating 75
Current Rating 96
Input Voltage Range
Power Terminals Input (L1/R, L2/S, L3/T), Output (T1/U, T2/V, T3/W), DCL (PO, PA), DC Bus (PA, PC)
Voltage Tolerance ±10%
Frequency Tolerance ±2%
Output Method Sine Wave Pulse-Width Modulated System
Output Frequency Range 0 to 299 Hz
Constant Torque, Variable Torque, Automatic Torque Boost, Sensor-Less Vector Control (Speed), V/f Five-Point Setting,
V/Hz Pattern
Permanent Magnet Control, Auto Power-Saver
Overload Current Rating 100% Continuous; 110% for One Minute
Frequency Control Rotary Encoder Integrated Into EOI, 0 to 10 VDC, ±10 VDC, 4 to 20 mA, Binary Input, Motor Operated Potentiometer
Frequency Accuracy Analog Input: ±0.2% of Maximum Output Frequency; Digital Input: ±0.01% of ±0.022 Hz of Output Frequency
Frequency Resolution Operation Panel: 0.01 Hz
Acceleration/Deceleration 0.1 to 6000 Seconds
Analog Inputs Three: One Isolated Input Selectable Between 0 to 10 VDC/4 to 20 mA, One 0 to 10 VDC, and One ±10 VDC
Analog Outputs Two Programmable to 57 Functions (One Switchable 0 to 10 VDC/0 to 20 mA, and One 0 to 1 mA)
Discrete Inputs Eight Programmable to 41 Functions
Sink/Source Switching Ability to Switch Between Sink Logic and Source Logic
Discrete Outputs Three Programmable to 83 Functions (Two Form-A and One Form-C); Outputs Rated at 2 A/120 VAC, 2 A/30 VDC
PID (Set Point Control) Adjustment of Proportional Gain, Integral Time, Differential Time, and Delay Filter
Braking Control DC Braking, Over-Flux Braking
Communication Ports Two-Wire/Four-Wire RS485
Communication Protocol BACNet
Protective Functions Overvoltage Stall, Overcurrent Stall, Critical (Skip) Frequencies, Ride-Through, Electronic Thermal Motor Protection
Interrupting Current Rating 100,000 AIC
Overcurrent, ASD Overheat, ASD Overload, Motor Overload, Overvoltage, Overtorque, Undercurrent, Ground Fault,
Faults Communication Time-Out, Analog-Input Terminal Overvoltage, Emergency Stop, Input/Output Phase Loss, RAM/ROM
Error, Undervoltage
Retry Ability to Reset Certain Faults Automatically; Programmable Up to 10 Retries
Restart Ability to Detect Speed and Direction of Freewheeling Motor and Start into Motor Smoothly
EOI Display Full-English Backlit LCD Display
Keys LOCAL/REMOTE, ESC, RUN, MODE, STOP/RESET
Rotary Encoder Encoder with Integrated Enter Key for Frequency and Parameter Adjustments
Monitoring Monitors 19 Drive Conditions
Display Units Programmed to Display Percentage or Volts/Amps
Temperature -10˚ to 40˚C
Relative Humidity Maximum 93% (Non-Condensing)
Altitude 1000 Meters or Less
3 to
230 V 1 to 2 HP
5 HP
5 to
460 V 1 to 3 HP
7.5 HP
Frame 2 3
Height (in.) 10.0 11.1
Width (in.) 5.1 6.1
Depth (in.) 6.0 6.5
Q9 Standard Specifications
2 3 5 7.5
7.8 11 17.5 25.3
2 3 5 7.5
3.4 4.8 7.6 11
100 125 150 200
124 156 180 240
Power Requirements
200 to 240 V, 50/60 Hz, Three-Phase
Control Specifications
® , LonWorks ® , Metasys N2 ® , Modbus RTU
Protection
Interface
Ambient Conditions
Q9 Dimensions
15 to 25 to
7.5 HP 10 HP
20 HP 30 HP
15 to 25 to
10 HP 40 HP
20 HP 30 HP
4 5A 5B 6
12.6 12.6 15.7 16.5
6.9 8.3 9.1 9.4
6.5 7.5 7.5 8.3
230 V
10 15 20 25
32.2 48.3 62.1 78.2
460 V, 50/60 Hz, Three-Phase
10 15 20 25
14 21 27 34
250 300 350 400
302 361 414 477
380 to 480 V, 50/60 Hz, Three-Phase
® , APOGEE FLN ®
40 to
- - 100 HP 125 HP
60 HP
50 to 75 to
- 150 HP 200 HP 250 HP
60 HP 125 HP
7A 7B 8 9B
21.7 21.7 24.8 36.2
9.4 12.6 12.6 12.2
8.3 9.5 11.4 14.6
30 40 50 60
92 120 150 177
30 40 50 60
40 52 65 77
- - -
300 to
400 HP
350 HP
10B 11B 12B 13A
40.2 46.9 46.9 46.9
13.8 13.0 16.9 23.0
14.6 14.6 14.6 14.6